SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The processing gain of a direct sequence spread spectrum system is approximately the ratio of the spreading code chip rate to the data rate. This paper provides a more accurate understanding of the performance of such systems as a function of the modulation scheme and jammer characteristics.
Pyrotechnic emergency-separation system includes shaped explosive charges that sever pair of hinges. System ensures reliable opening of escape hatch. Two pairs of cutters provided for each hinge so if one pair of cutters fails, other completes job. Pressure of explosions vented to prevent charge holders from fragmenting and forming sharp edges around open hatch. Exit slide deployed without tearing. Before detonation L-shaped retainers bear on hinge. After denonation, retainers fold outward to facilitate egress of severed hinges.
No abstract available
No abstract available
No abstract available
Granular matter takes many paths to pack in natural and industrial processes. The path influences the packing microstructure, particularly for frictional grains. We perform discrete element modeling simulations of different paths to construct packings of frictional spheres. Specifically, we explore four stress-controlled protocols implementing packing expansions and compressions in various combinations thereof. We characterize the eventual packed states through their dependence of the packing fraction and coordination number on packing pressure, identifying non-monotonicities with pressure that correlate with the fraction of frictional contacts. These stress-controlled, bulk-like particle simulations access very low-pressure packings, namely, the marginally stable limit, and demonstrate the strong protocol dependence of frictional granular matter.
Explore the source record for details and available documents.
A method transmitting a message over at least one of a plurality of radio frequency (RF) channels of an RF communications network is provided. The method comprises the steps of detecting a presence of jamming pulses in the at least one of the plurality of RF channels. The characteristics of the jamming pulses in the at least one of the plurality of RF channels is determined wherein the determined characteristics define at least interstices between the jamming pulses. The message is transmitted over the at least one of the plurality of RF channels wherein the message is transmitted within the interstices of the jamming pulse determined from the step of determining characteristics of the jamming pulses.
A method transmitting a message over at least one of a plurality of channels of a communications network is provided. The method comprises the steps of detecting a presence of jamming pulses in the at least one of the plurality of channels. The characteristics of the jamming pulses in the at least one of the plurality of channels is determined wherein the determined characteristics define at least interstices between the jamming pulses. The message is transmitted over the at least one of the plurality of channels wherein the message is transmitted within the interstices of the jamming pulse determined from the step of determining characteristics of the jamming pulses.
Packing of particles in a disordered arrangement has tremendous significance in both condensed matter physics and engineering applications. The last three decades have seen remarkable progress in our understanding of the physics of granular packings that has been largely facilitated by a rapid growth in the power of modern computers. Although granular packings are ubiquitous in diverse natural settings, from clogging of powders in hoppers to the crowding of living cells, a significant motivation for modeling granular packings has emerged from a proposal that the transition from a fluid-like state to a solid-like state of a granular material upon increasing volume fraction, called jamming, is intimately related to the origins of glass transition in thermal systems. As such, a majority of modeling efforts have focused on the jamming behavior of an idealized granular material: frictionless, monodisperse sphere. While such studies have illuminated the rich physics of jamming, granular materials in nature and engineering practice are rarely frictionless or monodisperse. The analogous research on the packing of these ‘real-world’ granular materials is still not fully developed. Besides requiring the exploration of a huge parameter space, three key computational considerations have inhibited their modeling: (i) traditional computational methods are not adept at simulating mechanically-stable packings of frictional particles near the jamming transition; (ii) standard algorithms of contact detection in discrete element methods are impractical to simulate granular packings with a wide distribution of particle sizes; (iii) a lack of well-established contact mechanics models of friction that can accurately reproduce experimental data. This chapter will review the latest computational advances to simulate the jamming of size-dispersed frictional particles, and describe the rich microstructural diversity that emerges in their packings.
Partial band noise jamming can severely degrade the performance of frequency-hopped, M-ary frequency-shift keyed communciation systems. This paper illustrates the tradeoffs between channel coding, diversity, and block orthogonal (MFSK) modulation as a means of overcoming the advantage of worst case, non-adaptive (as opposed to repeat-back) partial band jamming. For ease of computation, the analysis relies on exponentially tight error bounds, and is based on a noncoherent detection metric that requires jamming state information for each hop. A more robust, less complex receiver structure which eliminates the jamming knowledge requirement is shown to degrade performance less than 2-1/2 dB. The coding tradeoffs discussed in this report are exemplified in the design of a hypothetical 32 kb/s military frequency-hopped communication link.
In the event of a control surface failure, the purpose of a reconfigurable control system is to redistribute the control effort among the remaining working surfaces such that satisfactory stability and performance are retained. An Off-line Nonlinear General Constrained Optimization approach was used for the reconfigurable X-33 control design method. Three examples of failure are shown using a high fidelity 6 DOF simulation (case 1: ascent with a left body flap jammed at 25 deg.; case 2: entry with a right inboard elevon jam at 25 deg. and case 3: landing (TAEM) (Terminal Area Energy Management) with a left rudder jam at -30 deg.) Failure comparisons between responses with the nominal controller and reconfigurable controllers show the benefits of reconfiguration. Single jam aerosurface failures were considered, and failure detection and identification is considered accomplished in the actuator controller. The X-33 flight control system will incorporate reconfigurable flight control in the baseline system.
A reconfigurable control law for the full X-33 flight envelope has been designed to accommodate a failed control surface and redistribute the control effort among the remaining working surfaces to retain satisfactory stability and performance. An offline nonlinear constrained optimization approach has been used for the X-33 reconfigurable control design method. Using a nonlinear, six-degree-of-freedom simulation, three example failures are evaluated: ascent with a left body flap jammed at maximum deflection; entry with a right inboard elevon jammed at maximum deflection; and landing with a left rudder jammed at maximum deflection. Failure detection and identification are accomplished in the actuator controller. Failure response comparisons between the nominal control mixer and the reconfigurable control subsystem (mixer) show the benefits of reconfiguration. Single aerosurface jamming failures are considered. The cases evaluated are representative of the study conducted to prove the adequate and safe performance of the reconfigurable control mixer throughout the full flight envelope. The X-33 flight control system incorporates reconfigurable flight control in the existing baseline system.
In the event of a control surface failure, the purpose of a reconfigurable control system is to redistribute the control effort among the remaining working surfaces such that satisfactory stability and performance are retained. An Off-line Nonlinear General Constrained Optimization (ONCO) approach was used for the reconfigurable X-33 control design method. Three example failures are shown using a high fidelity 6 DOF simulation (case I ascent with a left body flap jammed at 25 deg.; case 2 entry with a right inboard elevon jam at 25 deg.; and case 3, landing (TAEM) with a left rudder jam at -30 deg.) Failure comparisons between responses with the nominal controller and reconfigurable controllers show the benefits of reconfiguration. Single jam aerosurface failures were considered, and failure detection and identification is considered accomplished in the actuator controller. The X-33 flight control system will incorporate reconfigurable flight control in the baseline system.
This work focuses on the properties of sheared granular materials near the jamming transition. The project currently involves two aspects. The first of these is an experiment that is a prototype for a planned ISS (International Space Station) flight. The second is discrete element simulations (DES) that can give insight into the behavior one might expect in a reduced-g environment. The experimental arrangement consists of an annular channel that contains the granular material. One surface, say the upper surface, rotates so as to shear the material contained in the annulus. The lower surface controls the mean density/mean stress on the sample through an actuator or other control system. A novel feature under development is the ability to 'thermalize' the layer, i.e. create a larger amount of random motion in the material, by using the actuating system to provide vibrations as well control the mean volume of the annulus. The stress states of the system are determined by transducers on the non-rotating wall. These measure both shear and normal components of the stress on different size scales. Here, the idea is to characterize the system as the density varies through values spanning dense almost solid to relatively mobile granular states. This transition regime encompasses the regime usually thought of as the glass transition, and/or the jamming transition. Motivation for this experiment springs from ideas of a granular glass transition, a related jamming transition, and from recent experiments. In particular, we note recent experiments carried out by our group to characterize this type of transition and also to demonstrate/ characterize fluctuations in slowly sheared systems. These experiments give key insights into what one might expect in near-zero g. In particular, they show that the compressibility of granular systems diverges at a transition or critical point. It is this divergence, coupled to gravity, that makes it extremely difficult if not impossible to characterize the transition region in an earth-bound experiment. In the DE modeling, we analyze dynamics of a sheared granular system in Couette geometry in two (2D) and three (3D) space dimensions. Here, the idea is to both better understand what we might encounter in a reduced-g environment, and at a deeper level to deduce the physics of sheared systems in a density regime that has not been addressed by past experiments or simulations. One aspect of the simulations addresses sheared 2D system in zero-g environment. For low volume fractions, the expected dynamics of this type of system is relatively well understood. However, as the volume fraction is increased, the system undergoes a phase transition, as explained above. The DES concentrate on the evolution of the system as the solid volume fraction is slowly increased, and in particular on the behavior of very dense systems. For these configurations, the simulations show that polydispersity of the sheared particles is a crucial factor that determines the system response. Figures 1 and 2 below, that present the total force on each grain, show that even relatively small (10 %) nonuniformity of the size of the grains (expected in typical experiments) may lead to significant modifications of the system properties, such as velocity profiles, temperature, force propagation, and formation shear bands. The simulations are extended in a few other directions, in order to provide additional insight to the experimental system analyzed above. In one direction, both gravity, and driving due to vibrations are included. These simulations allow for predictions on the driving regime that is required in the experiments in order to analyze the jamming transition. Furthermore, direct comparison of experiments and DES will allow for verification of the modeling assumptions. We have also extended our modeling efforts to 3D. The (preliminary) results of these simulations of an annular system in zero-g environment will conclude the presentation.
A piloted simulator experiment, designed to evaluate and optimize certain backup control system (BUCS) engagement parameters and to provide pilot familiarization with aircraft response prior to flight test of the BUCS in the YAH-64 Advanced Attack Helicopter, is described. Key elements of the simulation were the representation of a control system jam, the pilot's breaking of a shear pin in the jammed control, and the resultant BUCS engagement. To minimize the excursions in aircraft motion which could result from the pilot's control inputs after shear pin breakage, the BUCS control function is blended in gradually. The experiment's results indicate that optimum time to full control authority after shear pin breakage is three seconds in all axes for certain critical tasks. Special pilot training in the recovery from a control system jam may be necessary to minimize unacceptably large aircraft transients in the off-axis.
In the event of a control surface failure, the purpose of a reconfigurable control system is to redistribute the control effort among the remaining working surfaces such that satisfactory stability and performance are retained. Four reconfigurable control design methods were investigated for the X-33 vehicle: Redistributed Pseudo-Inverse, General Constrained Optimization, Automated Failure Dependent Gain Schedule, and an Off-line Nonlinear General Constrained Optimization. The Off-line Nonlinear General Constrained Optimization approach was chosen for implementation on the X-33. Two example failures are shown, a right outboard elevon jam at 25 deg. at a Mach 3 entry condition, and a left rudder jam at 30 degrees. Note however, that reconfigurable control laws have been designed for the entire flight envelope. Comparisons between responses with the nominal controller and reconfigurable controllers show the benefits of reconfiguration. Single jam aerosurface failures were considered, and failure detection and identification is considered accomplished in the actuator controller. The X-33 flight control system will incorporate reconfigurable flight control in the baseline system.