Search NASA⌕ Search

SEARCH · Search NASA

Results for “laminate modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Insulation or Irradiance: Exploring Why Bifacial Photovoltaics Run Hot

Bifacial photovoltaics are predicted to become the dominant device architecture over the next couple of years, but their thermal performance is not yet well understood. In this study, we model the thermal effects of different backside lamination materials on the performance of bifacial PERC cells. Glass-glass laminated cells were found to operate hotter than equivalent glass-polymer backsheet packed cells. This was solely due to the increased absorption of rear side incident light.

bifacial↗
DOE OSTI2023

Analyzing photovoltaic module mechanics using composite plate theories and finite element solutions

Deflection and stress calculated from an experimentally validated, high-fidelity finite element model (FEM) of a photovoltaic module experiencing mechanical load was compared to results from a simplified FEM treating the module laminate as a homogenized composite using a rule of mixtures approach, and further compared to analytical calculations treating the module as a Kirchoff-Love flat plate. The goal of this study was to determine the error incurred by analyzing module mechanics with varying levels of simplification, since resolving the aspect ratios of a module is computationally expensive. Homogenized FEMs were found to underpredict peak deflection under a 1.0 kPa load by between 13 and 19% for lower and upper bound application of the rule of mixtures. However, module shape was captured, implying that a useful replication of a resolved model could be achieved with a reduced, calibrated material stiffness. Homogenized stress results captured glass layer tensile stress components to within 46 to 52% at a sample location of interest, though agreement was poor through the remainder of the laminate due to the lack of material resolution. For plate theory, deflection was overpredicted by 45 to 67% for upper and lower bound homogenizations, and frame-adjacent module shapes were not adequately replicated. Stress results mirrored FEM trends but magnitudes were not well correlated to resolved model values. These results support the use of homogenized laminate models for module shape derivation, though resolved models remain necessary for stress analyses. The accuracy of plate theory was found to be inadequate for most applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Interface microstructure effects on dynamic failure behavior of layered Cu/Ta microstructures

Abstract Structural metallic materials with interfaces of immiscible materials provide opportunities to design and tailor the microstructures for desired mechanical behavior. Metallic microstructures with plasticity contributors of the FCC and BCC phases show significant promise for damage-tolerant applications due to their enhanced strengths and thermal stability. A fundamental understanding of the dynamic failure behavior is needed to design and tailor these microstructures with desired mechanical responses under extreme environments. This study uses molecular dynamics (MD) simulations to characterize plasticity contributors for various interface microstructures and the damage evolution behavior of FCC/BCC laminate microstructures. This study uses six model Cu/Ta interface systems with different orientation relationships that are as- created, and pre-deformed to understand the modifications in the plasticity contributions and the void nucleation/evolution behavior. The results suggest that pre-existing misfit dislocations and loading orientations (perpendicular to and parallel to the interface) affect the activation of primary and secondary slip systems. The dynamic strengths are observed to correlate with the energy of the interfaces, with the strengths being highest for low-energy interfaces and lowest for high-energy interfaces. However, the presence of pre-deformation of these interface microstructures affects not only the dynamic strength of the microstructures but also the correlation with interface energy.

42 ENGINEERING↗
DOE OSTI2026

Ultrafast (1‐5 sec) Lamination of Perovskite Solar Cells With Self‐Encapsulation Using Rapid Joule Heating

Perovskite solar cells (PSCs) are traditionally fabricated using sequential layer‐by‐layer deposition, in which each layer of the device is processed on top of the preceding layer. This constrains the processing techniques and selection of transport layer materials that can be used in the solar cell. To overcome these challenges, two half‐cells can be processed independently and then diffusion‐bonded through a lamination process. However, current lamination processes for perovskite solar cells suffer from relatively long process times, which can limit throughput when moving toward high‐volume manufacturing. In this study, a custom platform was designed for rapid‐joule heating of perovskite materials and devices. This enabled more than a 99% reduction in lamination time from 26 min to 1 s. Perovskite samples that were laminated in 1 s exhibited comparable values of percent bonded area, interfacial toughness, grain domain size, and X‐ray diffraction spectra to those laminated in greater than 10 min. As a proof‐of‐concept, 18.3% efficient devices were successfully laminated in 5 s. A transient heat transfer model was developed to describe the relationship between the perovskite temperature and the electrical power supplied to the heaters, establishing a baseline for predicting processing conditions in large‐scale manufacturing systems. Ultra‐fast lamination provides a pathway toward scalable roll‐to‐roll or sheet‐to‐sheet manufacturing of PSCs.

heat transfer↗
DOE OSTI2022

In-situ imaging of flexure-induced fracture in tape-laminate composites using high-resolution X-ray computed tomography

Here, this study presents development of an in-situ flexure test for imaging progressive inter- and intralaminar fracture in tape-laminate composites using X-ray computed tomography (CT). The intent of this test is to provide detailed experimental observations of ply-level damage that can be used to validate existing, and develop new, progressive damage analysis (PDA) tools. The test consists of a vertically mounted specimen which is flexed using two eccentric compressive loads using an in-situ uniaxial load stage. The flexure specimen contains a starter notch mid-span which promotes initiation of composite failure within the X-ray field of view. Specimens with two different laminate stacking sequences were tested, imaged, analyzed. For a quasi-isotropic laminate with large angle changes between adjacent plies, there was near simultaneous growth of transverse cracks and delaminations below the midplane of the laminate. For a laminate with small angles between adjacent plies, there was extensive formation of transverse crack networks which penetrated the laminate thickness without delamination growth. In addition to imaging fracture, the X-ray CT data from both specimen types were used to quantify the variability in thickness and analyze the local orientation of individual plies. Overall, the proposed test and the image-data analysis methodology provided an important insight into the fracture processes in tape laminates and highlights the inherent ply-level geometrical variabilities that should be accounted for in PDA simulations.

42 ENGINEERING↗
DOE OSTI2021

Next Generation Co-Molded One-Piece Automotive Parts

The purpose of this project was to determine the feasibility of co-molding Class A Sheet Molding Compound (SMC), structural SMC, and continuous fiber prepreg materials to produce a single piece co-molded automotive part, such as a hood. The combination of the three molding materials and the incorporation of selective design features (ribs, flanges, corrugations) was expected to eliminate the need for inner reinforcement panels, significantly reducing tooling costs and simplifying the manufacturing process. A multi-material solution would also result in significant weight savings. The scope of this project included the material characterization of the three materials, development of cure and flow simulation models, and validation of the models against parts molded with different combinations of the materials on an 11”x11” plaque tool with rib features. The intent of this project was to apply the learnings obtained from co-molding a part with simplified geometry to a Phase 2 project that would produce a single piece hood, co-molded with the same materials. Resins from INEOS Composites were provided to IDI to produce SMC and continuous fiber prepregs. Purdue University and INEOS Composites characterized the rheological and curing behavior of the different materials as well as the mechanical properties of the co-molded parts. This data was used by Purdue University to create simulation models. Models were created to predict both flow patterns and predict mechanical properties of different laminate constructions in and around the ribs. Michigan State University - Corktown validated Purdue’s models by co-molding the three materials in different combinations on a tool containing rib features provided by Century Tool. The co-molded parts were evaluated against the simulation models by Purdue, Corktown and INEOS. The project team demonstrated the following: • The ability to obtain a cohesive co-molded structure made up of Class A SMC, Structural SMC, and continuous fiber prepreg. • The ability to obtain a co-molded part with a Class A surface • Modeling of flow and fiber orientation • Modeling to predict mechanical properties of multi-material co-molded structures The predicted flow behavior and fiber orientation from simulations were then compared with the molded samples. Exact local orientation state was difficult to compare between microscopy and flow simulation, but captured general trends. Multi-material flow behavior was generally modeled well with SMC materials, but the introduction of woven material sheets requires further model development. Purdue compared the predicted versus actual mechanical properties, and INEOS Composites evaluated the surface appearance of unpainted and painted co-molded parts. The models developed by Purdue demonstrated that the mechanical properties can be predicted for parts with varying material configurations. The resulting models can be applied to future co-molded part design, tooling design, and molding conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact Fracture and Fragmentation of Glass via the 3D Combined Finite-Discrete Element Method

A driving technical concern for the automobile industry is their assurance that developed windshield products meet Federal safety standards. Besides conducting innumerable glass breakage experiments, product developers also have the option of utilizing numerical approaches that can provide further insight into glass impact breakage, fracture, and fragmentation. The combined finite-discrete element method (FDEM) is one such tool and was used in this study to investigate 3D impact glass fracture processes. To enable this analysis, a generalized traction-separation model, which defines the constitutive relationship between the traction and separation in FDEM cohesive zone models, was introduced. The mechanical responses of a laminated glass and a glass plate under impact were then analyzed. For laminated glass, an impact fracture process was investigated and results were compared against corresponding experiments. Correspondingly, two glass plate impact fracture patterns, i.e., concentric fractures and radial fractures, were simulated. The results show that for both cases, FDEM simulated fracture processes and fracture patterns are in good agreement with the experimental observations. The work demonstrates that FDEM is an effective tool for modeling of fracture and fragmentation in glass.

42 ENGINEERING↗
DOE OSTI2025

Experimental Validation of a Module Cell Cracking Model

The What's Cracking app can predict how changes in crystalline silicon photovoltaic (PV) module materials, design, and mounting affect its susceptibility for cell fracture under uniform loading. This work has experimentally validated the app. A set of commercial crystalline silicon PV modules was obtained for this study. The modules were uniformly loaded at three different mounting points, and their subsequent cell fractures were recorded. A large sample size allowed for the development of an experimental statistical model for cell fracture. Here, the comparison of the experiment to predictions from the app is in excellent agreement. Both experimental and modeling results also elucidate how moving the module mounting points toward the center of the module increases the probability of cell fracture.

14 SOLAR ENERGY↗
DOE OSTI2024

Understanding Process–Structure Relationships during Lamination of Halide Perovskite Interfaces

Fabrication of halide perovskite (HP) solar cells typically involves the sequential deposition of multiple layers to create a device stack, which is limited by the thermal and chemical incompatibility of top contact layers with the underlying HP semiconductor. One emerging strategy to overcome these restrictions on material selection and processing conditions is lamination, where two half-stacks are independently processed and then diffusion bonded to complete the device. Lamination reduces the processing constraints on the top side of the solar cell to allow new device designs, expanded use of deposition methods, and self-encapsulation of devices. While laminated perovskite solar cells with high efficiencies and novel interlayer combinations have been demonstrated, there is a limited understanding of how the lamination process parameters affect the diffusion-bond quality and material properties of the resulting HP layer. In this study, we systematically vary temperature, pressure, and time during lamination and quantify the resulting impacts on bonded area, grain domain size, and photoluminescence. A design of experiments is performed, and statistical analysis of the experimental results is used to quantitatively evaluate the resulting process–structure–property relationships. The lamination temperature is found to be the key parameter controlling these properties. Furthermore, a temperature of 150 °C enables successful bonding over 95% of the substrate area and also results in increases in apparent grain domain size and photoluminescence intensity. Based on these insights, the lamination temperature of functional perovskite solar cell devices is varied, demonstrating the importance of the resulting bond quality on device performance metrics.

14 SOLAR ENERGY↗
DOE OSTI2020

Hybrid fiber metal composite laminate interlaminar reinforcement through metal interlocks

Aircraft and automobile industries are continually seeking high-performance and lightweight solutions. Fiber-reinforced composites in conjunction with metals are being considered in the form of hybrid materials. There is a continuous need for improvement of interfacial bonding between composite layers and metal constituents. In this study, an innovative hybrid fiber interlocking metal hooks laminate (FIMHL) system was developed in which fiber-reinforced thermoset composite, and metal sheets are mechanically bonded together using out of plane hooks stamped in the metal. Process optimization was performed to gain the full benefit of the through-thickness reinforcement. Microstructural analysis showed improved interaction between the metal hooks and the fiber layers which reduced porosity and resin richness. This was reflected in mechanical properties, as tensile and flexural strength of FIMHL was enhanced by 38.5 and 18.8%, respectively, after process optimization. Furthermore, normalized weight fraction (76.4%) properties of FIMHL also confirmed that the increase in mechanical properties of optimized panel were not only due to increased reinforcement (glass fiber + aluminum) volume fraction but also because of improved metal hooks and fibers interaction. There was no significant effect on lap shear and fracture toughness, as they depend on bend back behavior of the hooks. A bilinear traction-separation model was used to characterize mode-I interlaminar fracture toughness properties, and 4.5% variation was recorded when modeling and experimental values were compared.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strength distributions of laminated FeNi-based metal amorphous nanocomposite ribbons

Metal Amorphous Nanocomposite (MANC) materials offer low losses at high magnetic switching frequency, enabling high power density motors with increased rotational speed. While MANCs have high strength, they are brittle. The use of motor components such as a rotor consisting of brittle material presents a reliability concern. Here, a promising MANC alloy is subjected to tensile tests and failure is observed with high-speed photography. A method is developed to prepare tensile specimens of laminated MANC and epoxy layers, simulating the stacking of an epoxy-impregnated tape-wound core. Tensile tests are conducted for single layer ribbon and for five- and ten-layer stacks of laminated material with thin layers of thermosetting epoxy. Failure distributions are shown to have increasing Weibull modulus with increasing layer count. The composite MANC material system is modeled using chain-of-bundles models. Using a k-failure model, we show that single ribbon strength distribution data can be used to predict well the failure distribution of laminated stacks. The agreement occurs when the assumed ineffective length, over which load is recovered in a failed layer, is comparable to the observed interlaminar separation length.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2026

Thermal Management for a Novel Non-Heavy Rare-Earth Interior Permanent Magnet Machine

The work presents a thermal management solution for a novel non-heavy rare-earth permanent magnet machine being developed at Oak Ridge National Laboratory. The motor has been designed to minimize losses while maximizing performance for a range of speeds and power ratings. The novel motor design reduces rare-earth magnet usage, thereby avoiding supply chain issues. The motor component heat losses are established for operating windows and desired performance. These heat losses, along with windage losses, are being used to develop cooling solutions for different components of this machine. A novel thermal management solution for stators and rotors has been developed, and progress is presented in this paper. The stator cooling is achieved with the help of water-ethylene glycol flowing over the finned aluminum stator jacket, and rotor cooling with automatic transmission fluid passing through novel channels designed in the rotor laminations. The attempt is to establish effective cooling of the stator winding, laminations, and rotor magnets. A 3D conjugate heat transfer model has been developed for overall thermal analysis to establish a down- selected thermal management solution for the machine. The model, in addition to estimated component heat losses, includes windage losses and its impact on rotor and stator cooling. Overall, the work presents a workable thermal solution for the interior permanent magnet machine with potential for further improvements. Future work will involve establishing end winding and refinement of other end parts of the machine with the aim of establishing a robust thermal management solution. The work will also focus on different shapes (e.g., round, non-round, presence of wedges) of rotor-stator gaps and investigate windage losses and their impact on thermal management for higher rotational speeds for the machine.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Non-local large-strain FFT-based formulation and its application to interface-dominated plasticity of nano-metallic laminates

Here, this paper presents a novel formulation and its robust numerical implementation of strain-gradient (SG) crystal plasticity within a large-strain (LS) elasto-viscoplastic (EVP) fast Fourier transform (FFT)-based micromechanical model. The resulting non-local SG-LS-EVPFFT formulation is used to model and understand the process of kink band formation during layer-parallel compression of nano-metallic laminates (NMLs). NMLs are layered composites with nanoscale thicknesses, thus requiring consideration of the interaction between dislocations and interfaces within the micromechanical model. The length-scale parameter of the SG model is calibrated by simulating a double pile-up and comparing predictions to analytical solution. This required new expressions for the defect energy, resulting in more accurate double pile-up predictions. The calibrated SG-LS-EVPFFT model is then used to simulate layer-parallel compression of copper-niobium NML. Formation of kink bands is predicted, and the model is used to rationalize the microscopic mechanisms enabling the formation process. It is found that accumulation of dislocations at interfaces leads to activation of layer-parallel slip, which in turn leads to kink band formation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhanced Planar Antenna Efficiency Through Magnetic Thin-Films

This work proposes to use magnetic material as the substrate of planar antennas to overcome the platform effect caused by the conducting ground plane. The upper bound of the radiation efficiency of an electric-current-driven low-profile antenna is theoretically derived, which is inversely proportional to the Gilbert damping factor of the magnetic material. Meanwhile, the improvement of radiation due to the use of magnetic material is demonstrated by a three-dimensional (3D) multiphysics and multiscale time-domain model. The simulation results match the theoretical derivation, showing 25% radiation efficiency from a planar antenna backed by a FeGaB thin film with 2.56 m thickness. Furthermore, for conductive ferromagnetic materials, it is shown that the eddy current loss can be well suppressed by laminating the thin film into multiple layers. Here, the radiation efficiency of the modeled antenna with a conductive ferromagnetic substrate is improved from 2.2% to 11.8% by dividing the substrate into 10 layers, with a ferromagnetic material fill factor of 93%.

42 ENGINEERING↗
DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗
DOE OSTI2026

Novel application of the modal strain energy technique for state-of-the-art damping predictions

Structural damping, which measures the energy dissipation of a vibrating structure, is a key modeling input for lightweight structures but is notoriously hard to predict. This work utilizes vibration-based measurements of centimeter-scale coupons and the modal strain energy approach to predict structural damping of a lightly damped structure. The approach was originally validated with panels shorter than a meter in length. This work extends the validation to a 2.75 m beam made of unidirectional and biaxial glass fiber laminates bonded by adhesive. The comparison between three-dimensional finite element model predictions and full-scale experimental measurements of damping show an average error of 5.2% for the first five modes. Additionally, the modal strain energy approach is newly applied with a one-dimensional geometrically exact beam theory model and a two-dimensional sectional analysis solver. This beam approach accurately predicts the damping behavior of the first bending modes but loses accuracy for higher order modes that are dominated by three-dimensional effects. This novel approach provides faster simulations while allowing arbitrary beam cross sections. The paper also investigates traditional and high-force dynamic mechanical analysis to measure structural damping of coupons. Both alternatives show significant errors in attempted validation against the theoretical thermoelastic damping of aluminum coupons.

17 WIND ENERGY↗
DOE OSTI2020

Angle of Incidence Characterization of Six Laminated Solar Cells for 2020 DTU Fotonik Inter-Laboratory Comparison Study

Photovoltaic energy prediction models include functions or modifiers to account for sun angle reflection losses. These functions may be known interchangeably as Angle of Incidence (AOI) or Incident Angle Modifier (IAM). While standards exist, there is no universally accepted single best practice for developing these functions. They can be generated through characterization of representative modules or single cells, in natural sunlight or indoors using simulated light sources. Repeatability of measurements and the viability of cross-laboratory comparisons are critical to confidence in validation of both methods. To investigate the differences between methods and labs, The Technical University of Denmark (DTU) initiated an international round-robin test comparison between several key test labs with AOI measurement capability. A total of six minimodules were provided in three different cell/interconnect/backsheet combinations. Sandia characterized these minimodules using methods developed over two decades specifically for the outdoor characterization of full-size photovoltaic modules. This report documents the characterization results, summarizes key observations and tabulates the processed data for comparison to results provided by other characterization labs.

14 SOLAR ENERGY↗
DOE OSTI2023

Residual Stresses Affect Cell Fragment Movement

Predictive modeling tools such as the finite element method can be of tremendous help in assessing the reliability and long-term performance of photovoltaic modules. In order to obtain accurate results, the proper modeling of materials and manufacturing processes are of utmost importance. Module fabrication introduces thermo-mechanical stresses inside the module laminate, which need to be accounted for as residual stresses in finite element simulations. We found that cell fragment movement and crack opening displacements of fractured silicon cells within modules are affected by those residual stresses. Cell cracking remains a challenging topic in assessing the reliability and durability of damaged modules. Hence, accurately quantifying the separation and movement between cell fragments creates the foundation for establishing reliable lifetime and performance assessments of fractured silicon modules. Here, we present a modeling approach that uses upper and lower bounds to accurately account for the residual stresses introduced by the module lamination process. We designed a four-point flexure coupon test of a laminated, fractured silicon strip to validate our numerical results and found good agreement between our modeling methodology and the experimental data. Finally, we discuss the implications of the residual stresses on the normal crack opening and metallization wear-out of fractured silicon cells.

14 SOLAR ENERGY↗