SEARCH · Search NASA

Results for “laser annealing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2022

The electronic Raman scattering spectrum of PuO 2

Here the Raman spectrum of PuO 2 was measured up to 13,000 cm –1 with three different laser excitation wavelengths spanning the resonance (405 nm), near-resonance (457 nm), and preresonance (514 nm) energy range. Approximately 26 never-before-seen bands were observed between 3500 and 13,000 cm –1 . Given the very high energy of the Raman shifts of these bands and the relative insensitivity of their spectral position to the interrogating laser wavelength, they are believed to arise from an electronic origin. These bands are present in both freshly calcined and radiolytically aged PuO 2 , although a broad luminescence is observed in the aged material, which obscures many of the high frequency features. In situ laser annealing of the material attenuated this luminescence and allowed for clear observation of these never-before-seen spectral features. Discovery of these high-energy bands presents a new way of identifying PuO 2 for nuclear nonproliferation and forensics purposes.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2025

Laser-induced selective local patterning of vanadium oxide phases

The same elements can form different compounds with widely different physical properties. Synthesis of a single-phase material is commonly achieved by controlling experimental conditions. Synthesizing materials that incorporate multiple specific spatially distributed chemical phases is often challenging, especially if different phases must be organized into well-defined spatial patterns. Here, we present an efficient solid reaction laser annealing (SRLA) approach to directly write regions of different local chemical compositions. We demonstrate the practical utility of our approach by locally writing microscale patterns of distinct chemical phases in vanadium oxide thin films. Specifically, we achieved the controlled local recrystallization of a uniform V 2 O 3 matrix into VO 2 , V 3 O 5 , and V 4 O 7 regions exhibiting sharp 1st- and 2nd-order metal–insulator phase transitions over a wide range of critical temperatures, i.e., a characteristic feature of select vanadium oxides that is extremely sensitive to even minute structural or compositional imperfections. We utilized the local chemical phase writing to pattern spiking oscillators with distinct electrical behavior directly in the thin film sample without employing elaborate lithography fabrication. Our laser tuning local chemical composition opens a pathway to synthesize a wide range of artificially micropatterned composite materials, with precision and control unattainable in conventional material synthesis methods.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

One–Step Fabrication of Nanocrystalline Nanonetwork SnO 2 Gas Sensors by Integrated Multilaser Processing

An integrated multilaser process is developed to fabricate nanocrystalline nanonetwork SnO 2 gas sensors in one integrated procedure, which combines electrodes fabrication, nanomaterials deposition, and postannealing. Interdigit electrodes are fabricated on an Au-coated fused silica substrate using a picosecond (ps) laser, which ablates the Au coating from the back of the substrate to pattern the electrodes. A novel transmitted Ps laser deposition (TPLD) process is designed to deposit SnO 2 nanonetwork on the interdigit electrodes with precise deposition area control under a close target-to-substrate distance. The obtained SnO 2 nanonetwork is in situ postannealed by a CO 2 laser to improve the crystallinity, while the nano morphology and grain size keep intact. To investigate the morphology and formation process of the nanonetwork, the microstructure of the laser-deposited SnO 2 layer is characterized. As a result, the crystallization control of CO 2 laser annealing is investigated through analyzing the Raman spectrum, X-ray diffraction (XRD) patterns, and lattice structures of the samples. By exposed to H 2 atmosphere, the fabricated gas sensor is demonstrated for H 2 monitoring.

08 HYDROGEN↗

DOE OSTI2021

Raman signatures from age-dating PuO 2 since last calcination

The self-irradiation of PuO 2 has been shown to affect the attributes of fifteen vibrational bands in the Raman spectrum. The vibrational bands correspond to the Raman allowed vibrational mode T 2g , overtones, defects, and bands from electronic origin. Defects in the crystal lattice from low-calcination temperature and alpha decay origins are responsible for the changes in the band attributes (band position, full-width half maximum (FWHM), intensity). Crystal lattice defects are also responsible for the growth of the defect bands. The temporal behavior of the vibrational bands can be used to estimate the age of the material since last calcination. Laser annealing was used to reset the material to full crystallinity prior to the aging study. 240 PuO 2 , with an alpha decay rate of 3.67 greater than the decay rate of 239 PuO 2 , was primarily used to assess the alpha decay-induced damage within 3 years. The aging study focused on the time-dependent properties of the T 2g band and the growth of defect bands. The FWHM of the T 2g band and the ratio of the areas of the defect bands/T 2g band were measured through a time period in excess of 3 years. The data from this study were found very close to the data describing the temporal evolution of the lattice constant measured with the X-ray diffraction (XRD) technique. The local physical properties of the material measured with Raman spectroscopy and the lattice parameter constant measured with XRD indicates a strong correlation between the two techniques. Although both techniques provide similar age-dating information, in contrast to the few milligram quantities required for XRD, Raman spectroscopy requires a 10 µm diameter PuO 2 particle to provide an estimate of the material age since last calcination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Investigating rapid alpha-decay induced aging of 238 PuO 2 by Raman Spectroscopy

Investigating alpha-decay induced aging in PuO 2 is useful in nuclear forensics; helping to determine the time since last calcination. This was previously investigate by monitoring the damage to 240 PuO 2 over the course of a few years. The rate of alpha-decay induced aging has long been assumed to scale only with the decay rate of other isotopes without direct verification. This article reports the first alpha-decay aging study of 238 PuO 2 by Raman spectroscopy. Contrary to the expected 10 days for 238 PuO 2 to reach steady state based on 240 PuO 2 studies, the alpha aging curve reached an approximate steady state ∼24–30 h after laser annealing. While the cause of the order of magnitude decrease is unknown, it is speculated that dynamic annealing could contribute to the differences in rate of induced aging. The Raman spectra of annealed and aged 238 PuO 2 matched the expected features in 239 PuO 2 and 240 PuO 2 spectra; showing no formation of new stable chemical species in the material such as secondary Pu oxide phases (e.g., Pu 4 O 9 ). In conclusion, results indicate that 238 Pu could be leveraged for rapid alpha-decay aging studies to characterize alpha-decay induced features and better understand matrix temperatures and the annealing of Frankel pair defects.

Actinide↗

DOE OSTI2020

Synthesis, Elasticity, and Spin State of an Intermediate MgSiO 3 -FeAlO 3 Bridgmanite: Implications for Iron in Earth's Lower Mantle

Fe-Al-bearing bridgmanite may be the dominant host for ferric iron in Earth's lower mantle. Here we report the synthesis of (Mg 0.5 Fe 3+ 0.5 )(Al 0.5 Si 0.5 )O 3 bridgmanite (FA50) with the highest Fe 3+ -Al 3+ coupled substitution known to date. X-ray diffraction measurements showed that at ambient conditions, the FA50 adopted the LiNbO 3 structure. Upon compression at room temperature to 18 GPa, it transformed back into the bridgmanite structure, which remained stable up to 102 GPa and 2,600 K. Fitting Birch-Murnaghan equation of state of FA50 bridgmanite yields V 0 = 172.1(4) Å 3 , K 0 = 229(4) GPa with K 0 ' = 4(fixed). Furthermore, the calculated bulk sound velocity of the FA50 bridgmanite is ~7.7% lower than MgSiO 3 bridgmanite, mainly because the presence of ferric iron increases the unit-cell mass by 15.5%. This difference likely represents the upper limit of sound velocity anomaly introduced by Fe 3+ -Al 3+ substitution. X-ray emission and synchrotron Mössbauer spectroscopy measurements showed that after laser annealing, ~6% of Fe 3+ cations exchanged with Al 3+ and underwent the high- to low-spin transition at 59 GPa. The low-spin proportion of Fe 3+ increased gradually with pressure and reached 17–31% at 80 GPa. Since the cation exchange and spin transition in this Fe 3+ -Al 3+ -enriched bridgmanite do not cause resolvable unit-cell volume reduction, and the increase of low-spin Fe 3+ fraction with pressure occurs gradually, the spin transition would not produce a distinct seismic signature in the lower mantle. However, it may influence iron partitioning and isotopic fractionation, thus introducing chemical heterogeneity in the lower mantle.

58 GEOSCIENCES↗

DOE OSTI2025

Laser activation of single group-IV colour centres in diamond

Abstract Spin-photon interfaces based on group-IV colour centres in diamond offer a promising platform for quantum networks. A key challenge in the field is realising precise single-defect positioning and activation, which is crucial for scalable device fabrication. Here we address this problem by demonstrating a two-step fabrication method for tin vacancy (SnV − ) centres that uses site-controlled ion implantation followed by local femtosecond laser annealing with in-situ spectral monitoring. The ion implantation is performed with sub-50 nm resolution and a dosage that is controlled from hundreds of ions down to single ions per site, limited by Poissonian statistics. Using this approach, we successfully demonstrate site-selective creation and modification of single SnV − centres. Our in-situ spectral monitoring opens a window onto materials tuning at the single defect level, and provides new insight into defect structures and dynamics during the annealing process. While demonstrated for SnV − centres, this versatile approach can be readily generalised to other implanted colour centres in diamond and wide-bandgap materials.

Science & Technology - Other Topics↗

DOE OSTI2022

Pressure-induced metallization and 3d-like behavior in TcS 2

TcS 2 undergoes a charge transfer insulator to metal transition above 28 GPa. Here, laser annealing reveals a kinetically hindered high pressure arsenopyrite phase that is recoverable to ambient. The new phase is similar to the Mn-dichalcogenides rather than the expected Redichalcogenides and involves the formation of S–S and Tc–Tc bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Novel Q-Carbon Anodes for Sodium-Ion Batteries

The lack of a standard anode for sodium-ion batteries (SIBs) has greatly hindered their applications. Herein, we show that a novel phase of carbon, namely Q-carbon, is an effective anode material for sodium-ion batteries. The Q-carbon, which is a metastable phase of carbon consisting of about 80% sp 3 - and 20% sp 2 -bonded carbon, is synthesized by nonequilibrium pulsed laser annealing and arc-discharge methods. Two types of Q-carbons, Q1 and Q2, were evaluated as anode material for SIBs. Q1 had a slow quench and was used as the control, whereas Q2 was Q-carbon with a rapid quenching. Q1 exhibits a high initial columbic efficiency of 81% and a low-capacity retention of less than 60%, whereas Q2 has a low initial columbic efficiency of 58% and a high-capacity retention of 81%. Q2 exhibits a stable capacity of 168 mAh·g −1 at a cycling rate of C/3 (124 mA·g −1 ), which is comparable to other hard carbon anodes reported in the literature. This unique synthesis method opens a pathway for the further tuning of Q-carbon with higher trapping/charging of Na + ions in improved SIBs.

25 ENERGY STORAGE↗

DOE OSTI2023

Enhancement in electro-optic performance of InAlGaAs/GaAs quantum dot lasers by ex situ thermal annealing

Here, this Letter reports the growth, fabrication, and characterization of molecular beam epitaxy (MBE)-grown quaternary InAlGaAs/GaAs quantum dot (QD) lasers emitting at sub-900 nm. The presence of Al in QD-based active regions acts as the origin of defects and non-radiative recombination centers. Applying optimized thermal annealing annihilates the defects in p-i-n diodes, thus lowering the reverse leakage current by six orders of magnitude compared to as-grown devices. A systematic improvement in the optical properties of the devices is also observed in the laser devices with increasing annealing time. At an annealing temperature of 700°C for 180 s, Fabry–Pérot lasers exhibit a lower pulsed threshold current density at infinite length of 570 A/cm 2 .

42 ENGINEERING↗

DOE OSTI2023

Microstructural evolution of rapidly solidified hypoeutectic Al 10Cu alloy during non-isothermal annealing transients induced by nano-second laser pulses

The evolution of characteristic nonequilibrium features presenting in morphologically distinct regions of rapid solidification (RS) microstructures in a hypoeutectic Al—10Cu (atomic %) in response to non-isothermal annealing transients has been studied by transmission electron microscopy (TEM). The capabilities of the Movie-Mode Dynamic TEM (MM-DTEM) instrument were used to expose select regions of the RS microstructure to sequences of rapid heating and cooling transients induced by nanosecond laser pulses while permitting in-situ observation. Partial melting, microstructural scale coarsening, morphological changes of the nonequilibrium features in the multi-phase RS microstructure, and solid-state phase transformation were observed. Heterogeneous nucleation of nanoscale θ-Al 2 Cu phase involved metastable supersaturated α-Al and the θ'-Al 2 Cu phases, establishing different sets of orientation relationships for the stable θ-Al 2 Cu and α-Al phases. Replacement of banded morphology grains that formed under conditions driven farthest from equilibrium by an equiaxed nanocrystalline structure comprised of α-Al phase, the primary solidification product, and an intergranular network of Al 2 Cu crystals has been attributed to local remelting. Here the experimental approach explored, permitted discovery of mechanistic details of location-specific transformation pathways activated in the multi-phase RS microstructure of hypoeutectic Al—Cu during subsequent nonisothermal transients.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Role of scan strategies and heat treatment on grain structure evolution in Fe-Si soft magnetic alloys made by laser-powder bed fusion

A major goal in printing soft magnetic Fe-Si steels using additive manufacturing is to take advantage of the potential for complex geometric designs and site-specific grain control. One major step in the processing of these alloys is understanding how processing parameters might impact how the as-built microstructure responds to annealing (i.e. the annealing response). The impact of scan strategy on the annealing response for thin wall geometries is specifically explored. Two scan strategies were explored for a thin wall geometry that produced a strongly columnar grain structure and equiaxed grain structure. Additionally, samples from both scan strategies annealed at 1200 °C showed a marked difference in annealing response with the more equiaxed sample seeing full recrystallization and grain growth, while the more columnar grain structure saw little change in microstructure. After analysis through characterization techniques and thermal-mechanical simulations Differences in internal energy within the grains were ruled out because calculated GND density values were similar for both samples. The formation of secondary particles was ruled out as a contributing factor due to the type of oxide formations and their size. It was concluded that the contributing factor to the difference in the annealing response were a difference in the resulting grain size and the density of high angle grain boundaries. These two differences were largely attributed to differences in the thermal gradient conditions due to grains preferentially growing in the direction of the steepest thermal gradient.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗

DOE OSTI2021

β -Technetium: An allotrope with a nonstandard volume-pressure relationship

In this work, we report the synthesis and structure of the second allotrope of technetium, β-Tc. Transformative pathways are accessed at extreme conditions using the laser-heated diamond anvil cell and confirmed with in situ synchrotron x-ray diffraction and Raman spectroscopy. βTc is fully recoverable to ambient conditions, although counter to our DFT calculations predicting a face-centered-cubic lattice, we observe a tetragonal structure (I4/mmm) that exhibits further tetragonal distortion with pressure. β-Tc has an expanded volume relative to the hcp ground state phase, that when doped with nitrogen has an unexpected volume lowering. Such anomalous behavior is possibly indicative of a rare electronic phase transition in a 4d element.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Laser Crystallization and Dopant Activation of a-Si:H Carrier-Selective Layer in TOPCon Si Solar Cells

Herein, we present a pulsed-laser processing method for crystallization and dopant activation of a highly n-doped amorphous silicon (a-Si:H) carrier-selective layer in a tunnel oxide passivated contact (TOPCon) Si solar cell structure. Here, the laser method provides enhanced conductivity and implied open circuit voltage while reducing emitter saturation current density and surface heating, as opposed to conventional high-temperature furnace annealing of the bulk Si wafer with a TOPCon structure. We identify an appropriate laser wavelength, fluence, and layer thickness using modeling and simulations. Raman and Hall effect measurements demonstrate increased crystallinity and dopant activation, whereas photoconductive decay shows enhanced surface and interface passivation quality. Additionally, we examine the role of subsequent SiNx deposition on further improving the passivation of laser-processed TOPCon layers to achieve a 5.9 kΩ/sq film sheet resistance, 2 ms effective carrier lifetime, 718 mV implied open-circuit voltage (iVOC), and 8.6 fA/cm 2 one-side recombination current density (J0) with the potential for further passivation improvement via laser process and a-Si layer thickness optimization.

14 SOLAR ENERGY↗

DOE OSTI2026

Laser-Induced Enhancement of Acoustic Mode Quality Factor Revealed by Correlated Single-Particle Optical and Electron Microscopy

Acoustic modes in plasmonic nanostructures provide fundamental insights into their optomechanical behavior at the nanoscale, enabling emerging applications in plasmon-enhanced optomechanics, ultrasensitive sensing, and nanoscale energy transduction. Here we explore the modulation of acoustic phonon dynamics in lithographically fabricated gold nanodisks via laser-induced photothermal annealing. Using a correlated approach that utilizes both single-particle transient extinction spectroscopy and advanced electron microscopy, we directly link nanoscale structural transformations to changes in mechanical properties as probed through the coherence of the excited acoustic modes. Specifically, ultrafast pump–probe microscopy reveals an enhancement in the acoustic mode quality factor of annealed gold nanodisks, indicative of reduced damping and improved vibrational coherence. Structural characterization via scanning electron microscopy and electron backscatter diffraction confirms that photoinduced annealing results in smoother surface morphology and overall enhanced crystallinity. The improved crystalline order reduces defect and crystal boundary scattering, which we suggest as the reason underlying the lower quality factor before annealing. Furthermore, these findings demonstrate that targeted structural engineering at the nanoscale offers a powerful strategy for optimizing the optomechanical performance of plasmonic nanostructures, with broad implications for the design of next-generation nanophotonic and optomechanical systems.

Annealing (metallurgy)↗

DOE OSTI2022

A Laboratory-driven Multiscale Investigation of X-Ray Induced Mass Loss and Photochemical Evolution in Cosmic Carbon and Silicate Dust

We present the results of an integrated laboratory and modeling investigation into the impact of stellar X-rays on cosmic dust. Carbonaceous grains were prepared in a cooled (< 200 K) supersonic expansion from aromatic molecular precursors, and were later irradiated with 970 eV X-rays. Silicate (enstatite) grains were prepared via laser ablation, thermally annealed, and later irradiated with 500 eV X-rays. Infrared spectra of the 3.4 μm band of the carbon sample prepared with benzene revealed 84% ± 5% band area loss for an X-ray dose of 5.2 x 10 23 eV.cm -2 . Infrared spectra of the 8 -12 μm Si-O band of the silicate sample revealed band area loss up to 63% ± 5% for doses of 2.3 x 10 23 eV.cm -2 . A hybrid Monte Carlo particle trajectory approach was used to model the impact of X-rays and ensuing photoelectrons, Auger and collisionally ionized electrons through the bulk. As a result of x-ray ionization and ensuing Coulomb explosions on surface molecules, the calculated mass loss is 60% for the carbonaceous sample and 46% for the silicate sample, within a factor of 2 of the IR band loss, supporting an X-ray induced mass-loss mechanism. We apply the laboratory X-ray destruction rates to estimate the lifetimes of dust grains in protoplanetary disks surrounding 1 M ⊙ and 0.1 M ⊙ G and M stars. In both cases, X-ray destruction timescales are short (a few million years) at the disk surface, but are found to be much longer than typical disk lifetimes (≳10 Myr) over the disk bulk.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2024

Atomistic Probing of Defect-Engineered 2H-MoTe 2 Monolayers

Point defects dictate various physical, chemical, and optoelectronic properties of two-dimensional (2D) materials, and therefore, a rudimentary understanding of the formation and spatial distribution of point defects is a key to advancement in 2D material-based nanotechnology. In this work, we performed the demonstration to directly probe the point defects in 2H-MoTe 2 monolayers that are tactically exposed to (i) 200 °C-vacuum-annealing and (ii) 532 nm-laser-illumination; and accordingly, we utilize a deep learning algorithm to classify and quantify the generated point defects. We discovered that tellurium-related defects are mainly generated in both 2H-MoTe 2 samples; but interestingly, 200 °C-vacuum-annealing and 532 nm-laser-illumination modulate a strong n-type and strong p-type 2H-MoTe 2 , respectively. While 200 °C-vacuum-annealing generates tellurium vacancies or tellurium adatoms, 532 nm-laser-illumination prompts oxygen atoms to be adsorbed/chemisorbed at tellurium vacancies, giving rise to the p-type characteristic. This work significantly advances the current understanding of point defect engineering in 2H-MoTe 2 monolayers and other 2D materials, which is critical for developing nanoscale devices with desired functionality.

2H-MoTe 2↗