Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser beam cutting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Velocity surface measurements for ZnO films over /001/-cut GaAs

A potential application for a piezoelectic film deposited on a GaAs substrate is the monolithic integration of surface acoustic wave (SAW) devices with GaAs electronics. Knowledge of the SAW properties of the filmed structure is critical for the optimum design of such devices. In this article, the measurements of the velocity surface, which directly affects the SAW diffraction, on the bare and metallized ZnO/SiO2 or Si3N4/GaAs /001/-cut samples are reported using two different techniques: (1) knife-edge laser probe, (2) line-focus-beam scanning acoustic microscope. Comparisons, such as measurement accuracy and tradeoffs, between the former (dry) and the latter (wet) method are given. It is found that near the group of zone axes (110) propagation direction the autocollimating SAW property of the bare GaAs changes into a noncollimating one for the layered structure, but a reversed phenomenon exists near the group of zone axes (100) direction. The passivation layer of SiO2 or Si3N4 (less than 0.2 micrometer thick) and the metallization layer change the relative velocity but do not significantly affect the velocity surface. On the other hand, the passivation layer reduces the propagation loss by 0.5-1.3 dB/microseconds at 240 MHz depending upon the ZnO film thickness. Our SAW propagation measurements agree well with theorectical calculations. We have also obtained the anisotropy factors for samples with ZnO films of 1.6, 2.8, and 4.0 micrometer thickness. Comparisons concerning the piezoelectric coupling and acoustic loss between dc triode and rf magnetron sputtered ZnO films are provided.

Kim, Yoonkee↗
NASA NTRS1995

ZnO films on /001/-cut (110)-propagating GaAs substrates for surface acoustic wave device applications

A potential application for piezoelectric films substrates is the monolithic integration of surface acoustic wave (SAW) devices with GaAs electronics. Knowledge of the SAW properties of the layered structure is critical for the optimum and accurate design of such devices. The acoustic properties of ZnO films sputtered on /001/-cut group of (110) zone axes-propagating GaAs substrates are investigated in this article, including SAW velocity, effective piezoelectric coupling constant, propagation loss, diffraction, velocity surface, and reflectivity of shorted and open metallic gratings. The measurements of these essential SAW properties for the frequency range between 180 and 360 MHz have been performed using a knife-edge laser probe for film thicknesses over the range of 1.6-4 micron and with films of different grain sizes. The high quality of dc triode sputtered films was observed as evidenced by high K(sup 2) and low attenuation. The measurements of the velocity surface, which directly affects the SAW diffraction, on the bare and metalized ZnO on SiO2 or Si3N4 on /001/-cut GaAs samples are reported using two different techniques: (1) knife-edge laser probe, (2) line-focus-beam scanning acoustic microscope. It was found that near the group of (110) zone axes propagation direction, the focusing SAW property of the bare GaAs changes into a nonfocusing one for the layered structure, but a reversed phenomenon exists near the (100) direction. Furthermore, to some extent the diffraction of the substrate can be controlled with the film thickness. The reflectivity of shorted and open gratings are also analyzed and measured. Zero reflectivity is observed for a shorted grating. There is good agreement between the measured data and theoretical values.

Hickernell, Frederick S.↗
NASA NTRS1995

ZnO Films on {001}-Cut <110>-Propagating GaAs Substrates for Surface Acoustic Wave Device Applications

A potential application for piezoelectric films on GaAs substrates is the monolithic integration of surface acoustic wave (SAW) devices with GaAs electronics. Knowledge of the SAW properties of the layered structure is critical for the optimum and accurate design of such devices. The acoustic properties of ZnO films sputtered on {001}-cut <110> -propagating GaAs substrates are investigated in this article, including SAW Velocity effective piezoelectric coupling constant, propagation loss. diffraction, velocity surface, and reflectivity of shorted and open metallic gratings. The measurements of these essential SAW properties for the frequency range between 180 and 360 MHz have been performed using a knife-edge laser probe for film thicknesses over the range of 1.6-4 micron and with films or different grain sizes. The high quality of dc triode sputtered films was observed as evidenced by high K(exp 2) and low attenuation. The measurements of the velocity surface, which directly affects the SAW diffraction, on the bare and metalized ZnO on SiO2, or Si3N4 on {001}-cut GaAs samples are reported using two different techniques: 1) knife-edge laser probe, 2) line-focus-beam scanning acoustic microscope. It was found that near the <110> propagation direction, the focusing SAW property of the bare GaAs changes into a nonfocusing one for the layered structure, but a reversed phenomenon exists near the <100> direction. Furthermore, to some extent the diffraction of the substrate can be controlled with the film thickness. The reflectivity of shorted and open gratings are also analyzed and measured. Zero reflectivity is observed for a shorted grating. There is good agreement between the measured data and theoretical values.

Kim, Yoonkee↗
DOE OSTI2021

Proton beam quality enhancement by spectral phase control of a PW-class laser system

We report on experimental investigations of proton acceleration from solid foils irradiated with PW-class laser-pulses, where highest proton cut-off energies were achieved for temporal pulse parameters that varied significantly from those of an ideally Fourier transform limited (FTL) pulse. Controlled spectral phase modulation of the driver laser by means of an acousto-optic programmable dispersive filter enabled us to manipulate the temporal shape of the last picoseconds around the main pulse and to study the effect on proton acceleration from thin foil targets. The results show that applying positive third order dispersion values to short pulses is favourable for proton acceleration and can lead to maximum energies of 70 MeV in target normal direction at 18 J laser energy for thin plastic foils, significantly enhancing the maximum energy compared to ideally compressed FTL pulses. The paper further proves the robustness and applicability of this enhancement effect for the use of different target materials and thicknesses as well as laser energy and temporal intensity contrast settings. We demonstrate that application relevant proton beam quality was reliably achieved over many months of operation with appropriate control of spectral phase and temporal contrast conditions using a state-of-the-art high-repetition rate PW laser system.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2011

Laser Oscillator Incorporating a Wedged Polarization Rotator and a Porro Prism as Cavity Mirror

A laser cavity was designed and implemented by using a wedged polarization rotator and a Porro prism in order to reduce the parts count, and to improve the laser reliability. In this invention, a z-cut quartz polarization rotator is used to compensate the wavelength retardance introduced by the Porro prism. The polarization rotator rotates the polarization of the linear polarized beam with a designed angle that is independent of the orientation of the rotator. This unique property was used to combine the retardance compensation and a Risley prism to a single optical component: a wedged polarization rotator. This greatly simplifies the laser alignment procedure and reduces the number of the laser optical components.

Li, Steven↗
NASA NTRS1987

Determining Optical Axes of Uniaxial Crystals

Polarizing-microscope concept adapted for thick samples. Optical axis of crystal usually found by examining sample thinner than 1 mm between crossed polarizing plates. Frequently impractical to cut off small sample of crystal for testing, technique modified to accommodate large crystals. Ability to circumvent effect of birefringence has applications where laser beams must be transmitted through uniaxial crystals, as in laser diagnostics of contained flows in systems requiring windows for optical access.

Schock, H. J.↗
NASA NTRS2013

A Hybrid Fiber/Solid-State Regenerative Amplifier with Tunable Pulse Widths for Satellite Laser Ranging

A fiber/solid-state hybrid seeded regenerative amplifier, capable of achieving high output energy with tunable pulse widths, has been developed for satellite laser ranging applications. The regenerative amplifier cavity uses a pair of Nd:YAG zigzag slabs oriented orthogonally to one another in order to make thermal lensing effects symmetrical and simplify optical correction schemes. The seed laser used is a fiber-coupled 1,064-nm narrowband (<0.02 nm) diode laser that is discretely driven in a new short-pulsed mode, enabling continuously tunable seed pulse widths in the 0.2-to-0.4-ns range. The amplifier gain unit consists of a pair of Brewster-cut 6-bounce zigzag Nd:YAG laser slabs, oriented 90deg relative to each other in the amplifier head. This arrangement creates a net-symmetrical thermal lens effect (an opposing singleaxis effect in each slab), and makes thermo-optical corrections simple by optimizing the curvature of the nearest cavity mirror. Each slab is pumped by a single 120-W, pulsed 808-nm laser diode array. In this configuration, the average pump beam distribution in the slabs had a 1-D Gaussian shape, which matches the estimated cavity mode size. A half-wave plate between the slabs reduces losses from Fresnel reflections due to the orthogonal slabs Brewster-cut end faces. Successful "temporal" seeding of the regenerative amplifier cavity results in a cavity Q-switch pulse envelope segmenting into shorter pulses, each having the width of the input seed, and having a uniform temporal separation corresponding to the cavity round-trip time of approx. =10 ns. The pulse energy is allowed to build on successive passes in the regenerative amplifier cavity until a maximum is reached, (when cavity gains and losses are equal), after which the pulse is electro- optically switched out on the next round trip The overall gain of the amplifier is approx. =82 dB (or a factor of 1.26 million). After directing the amplified output through a LBO frequency doubling crystal, approx. = 2.1 W of 532-nm output (>1 mJ) was measured. This corresponds to a nonlinear conversion efficiency of >60%. Furthermore, by pulse pumping this system, a single pulse per laser shot can be created for the SLR (satellite laser ranging) measurement, and this can be ejected into the instrument. This is operated at the precise frequency needed by the measurement, as opposed to commercial short-pulsed, mode-locked systems that need to operate in a continuous fashion, or CW (continuous wave), and create pulses at many MHz. Therefore, this design does not need to throw away or dump 99% of the laser energy to produce what is required; this system can be far smaller, more efficient, cheaper, and readily deployed in the field when packaged efficiently. Finally, by producing custom diode seed pulses electronically, two major advantages over commercial systems are realized: First, this pulse shape is customizable and not affected by the cavity length or gain of the amplifier cavity, and second, it can produce adjustable (selectable) pulse widths by simply adding multiple seed diodes and coupling each into commercial, low-cost fiber-optic combiners.

Coyle, Barry↗
DOE OSTI2020

Coating adhesion of a chromate-containing epoxy primer on Al2024-T3 surface processed by laser-interference

In this work, the coating adhesion test results are presented for a primer that was coated on laser-interference structured surfaces of as-received Al2024-T3 specimens, i.e., without employing any polishing, cleaning, or any other surface alteration techniques. All of the laser-interference processing was performed by splitting the primary beam of a Q-switched Nd:YAG pulsed nanosecond laser into two beams and focused them to the same spot. The specimens were spray painted with a chromate-containing epoxy primer, CA7233, compliant to MIL-PRF-23377 Type I Class C2 specification. The adhesion of primer on Al surface with different treatments was assessed using the ASTM D3359 X-cut and cross-hatch tests. It was found that the laser processed specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking for coating adhesion specimens than those prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. The rastering with either 4 mm/s or 6 mm/s with a laser fluence of 1.78 J/cm2 is recommended to attain acceptable coating adhesion, even higher than that with the anodizing surface treatment.These results indicate that laser-interference shows significant potential as a non-chemical surface preparation technique for these coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Topological Excitations in Pyrochlore Heterostructures

This research project focuses on developing innovative materials that demonstrate unique quantum properties, specifically within electron systems that exhibit complex interactions, known as "correlated electron systems." Unlike non-correlated materials, finding topological phases (special states of matter with protected properties that make them stable against defects) in these correlated systems is a significant challenge. The project aims to design synthetic templates of two-dimensional "Kagome lattice" structures, made from specific materials called iridates and osmates, to study and control these exotic quantum behaviors. To achieve this, the project employs a cutting-edge spectroscopic tools that allow precise analysis of artificial quantum materials in terms of both energy and momentum while they are being created, using a specialized laser-based process called laser Molecular Beam Epitaxy.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Automated space fabrication of structural elements

A description is presented of an automated space fabrication technique for basic structural elements, taking into account as representative the design loads and requirements of the solar power satellite structure. Roll forming for continuous cap and brace members is applicable for all proposed metallic materials. Spot-welding, electron beam welding, ultrasonic welding, laser welding, cold welding, and various mechanical fastening techniques are applicable for the automated fabrication process. Termination of the formed cap and brace members can be accomplished by sawing, shearing, punching, and laser cutting. The most cost effective materials were found to be the aluminum alloys. Selected for further study were AL20224T3 and AL2219-T62. In the area of fiber composites, thermoplastic matrix materials with graphite fibers were selected for future studies.

Engler, E. E.↗
DOE OSTI2025

Experimental Generation of Extreme Electron Beams for Advanced Accelerator Applications

In this Letter, we report on the experimental generation of high energy (10 GeV), ultrashort (femtosecond-duration), ultrahigh current (∼ 0.1 MA), petawatt peak power electron beams in a particle accelerator. These extreme beams enable the exploration of a new frontier of high-intensity beam-light and beam-matter interactions broadly relevant across fields ranging from laboratory astrophysics to strong field quantum electrodynamics and ultrafast quantum chemistry. We demonstrate our ability to generate and control the properties of these electron beams by means of a laser-electron beam shaping technique. In conclusion, this experimental demonstration opens the door to on-the-fly customization of extreme beam current profiles for desired experiments and is poised to benefit a broad swath of cross-cutting applications of relativistic electron beams.

43 PARTICLE ACCELERATORS↗
NASA NTRS2000

Fluid Inclusions in Extraterrestrial Samples Fact or Fiction?

Over the years there have been numerous reports of liquid inclusions in meteorites. Roedder reviews the reported occurrences of liquid inclusions in meteorites and states that "silicate-melt inclusions are expectable and apparently ubiquitous, but the presence of actual liquid inclusions (i.e., with moving bubbles at room temperature) would seem almost impossible." The reason for this conclusion is that meteorites (presumably) form in space at high temperatures and very low pressures where liquid water (or carbon dioxide) is not stable. Perhaps the most infamous report of fluid inclusions in meteorites was that of Warner et al. In that study, the authors reported the presence of two-phase, liquid-vapor inclusions in a diogenite from Antarctica. This report of fluid inclusions generated considerable interest in the meteorite community, and caused many to question existing models for the origin of the diogenites. This interest was short-lived however, as later investigations of the same samples showed that the inclusions were most likely artifacts. Rudnick et al. showed that many of the inclusions in meteorites prepared at the Johnson Space Center contained a fluid that fluoresced strongly under the laser beam on the Raman microprobe. They interpreted this to indicate that the inclusions contained Almag oil used in the preparation of thin sections. Presumably, the Almag oil entered empty vesicles along fractures that were opened intermittently during cutting. Here, the occurrence of unambiguous fluid inclusions that could not have been introduced during sample preparation are described in samples from two different extraterrestrial environments. One environment is represented by the SNC (martian) meteorites ALH 84001 and Nakhla. The second environment is represented by the Monahans 1998 meteorite that fell recently in the USA.

Bodnar, R. J.↗
DOE OSTI2020

Poling thin-film x-cut lithium niobate for quasi-phase matching with sub-micrometer periodicity

Quasi-phase-matched grating structures in lithium niobate waveguides with sub-micrometer periodicities will benefit the development of short-wavelength nonlinear optical devices. Here, we report on the reproducible formation of periodically poled domains in x-cut single-crystalline thin-film lithium niobate with periodicities as short as 600 nm. Shaped single-voltage poling pulses were applied to electrode structures that were fabricated by a combination of electron-beam and direct-writing laser lithography. Evidence of successful poling with good quality was obtained through second-harmonic microscopy and piezoresponse force microscopy imaging. For the sub-micrometer period structures, we observed patterns with a double periodicity formed by domain interactions and features with sizes <200 nm.

Zhao, Jie (ORCID:0000000306230125)↗
DOE OSTI2025

Wafer-Free Crystalline Silicon Solar Cells (CRADA Final Report)

This CRADA project, based on the DOE Solar Energy Technologies Office (SETO) Solar Prize Voucher program, helped Leap Photovoltaics to develop methodologies to immobilize Si particles by permanently attaching them to an Al-coated substrate and thereby forming carrier-selective electrical contacts to the Si particles. The bigger goal was to help Leap Photovoltaics develop these immobilized and contacted particle arrays into relatively efficient, inexpensive, and industrially relevant solar cells. By using Si particles instead of wafers in a solar cell absorber layer, one can avoid costs associated with growing monocrystalline Si ingots, then diamond-sawing them into wafers, then processing wafers into cells – a mainstream practice in today's high-efficiency Si cell and module technology. Monocrystalline or polycrystalline Si particles can be obtained in various ways: for example, Si kerf from wafer sawing is monocrystalline; recycled Si cell wafers can be ball-milled into particles; particles can be grown using various gas-phase techniques (mostly from SiH4). These Si particles can be assembled onto a substrate and serve as an absorber layer for the solar cell, absorbing photons to generate photocarriers. The challenge with this technique is to collect photocarriers from individual Si particles, with separation of photogenerated electrons to the negative cell’s electrode and positive photogenerated holes to the positive electrode. Therefore, each particle must have two isolated, carrier-selective contacts: one for electrons and one for holes. Plus, particles need to be immobilized onto a solid substrate. The goal of this work was focused on the immobilization of Si particles and creating hole-selective contact to them at the same time, using industrially relevant Si photovoltaic (PV) cell technology: screen printing of Al back-surface field electrodes. This is used in the mainstream Propane Education and Research Council (PERC) technology for hole-collecting contacts at the back of the cell. The work performed at NREL consisted of screen printing of Al metal paste on substrates, spreading Si particles onto it, and thermally processing the structures to form hole-collecting contacts. The final structures were investigated by scanning electron microscopy (SEM) after focused ion beam (FIB) cross-sectioning and polishing. The work was done jointly by NREL staff and Leap Photovoltaics (Leap PV) employees stationed at NREL. The samples were then taken to Leap PV for further processing. Training the Leap PV employee on various NREL techniques (laser cutting, screen printing, thermal processing, characterization) was part of the scope.

14 SOLAR ENERGY↗
NASA NTRS1995

Instruments Sniff Organic Surface Contaminants

Portable instruments detecting both nonvolatile and volatile organic surface contaminants in real time developed. Instruments easy to use: operate under ordinary ambient atmospheric conditions, without need to use messy liquid solvents or install and remove witness plates, and without need to cut specimens from surfaces to be inspected. Principle of detection involves sweeping pure, activated gas across surface spot inspected, then monitoring light emitted at wavelengths characteristic of excited molecules formed by chemical reactions between activated gas and contaminants. Gas activated by dc discharge, radio-frequency induction, microwave radiation, laser beam, hot filaments, or any other suitable means that excites some of gas molecules.

Adler-Golden, Steven↗
NASA NTRS1997

Super-Compact Laser

Microcosm, Inc. produced the portable Farfield-2 laser for field applications that require high power pulsed illumination. The compact design was conceived through research at Goddard Space Flight Center on laser instruments for space missions to carry out geoscience studies of Earth. An exclusive license to the key NASA patent for the compact laser design was assigned to Microcosm. The FarField-2 is ideal for field applications, has low power consumption, does not need water cooling or gas supplies, and produces nearly ideal beam quality. The properties of the laser also make it effective over long distances, which is one reason why NASA developed the technology for laser altimeters that can be toted aboard spacecraft. Applications for the FarField-2 include medicine, biology, and materials science and processing, as well as diamond marking, semiconductor line-cutting, chromosome surgery, and fluorescence microscopy.

Source record↗
NASA NTRS2000

Pumped up Lasers

Cutting Edge Optronics released the first of potentially three products to result from an SBIR contract with Goddard Space Flight Center. The first commercial result is the WhisperMiniSlab, a diode pump for high performance laser systems. The slab uses a zig-zag path through the laser crystal which eliminates the need for thermal lensing. The result is smaller lasers with better beam quality for use in medical and industrial applications.

Source record↗
NASA NTRS1998

Off-beam (multiply-scattered) lidar returns from stratus: Cloud-information content and sensitivity to noise - 1

We review the basic multiple scattering theory of off-beam lidar returns from optically thick clouds using the diffusion approximation. The shape of the temporal signal - the stretched pulse - depends primarily on the physical thickness of the cloud whereas its spatial counterpart - the diffuse spot - conveys specific information on the cloud's optical thickness, as do the absolute returns. This makes observation of the weak off-beam lidar returns an attractive prospect in remote sensing of cloud properties. By estimating the signal-to-noise ratio, we show that night-time measurements can be performed with existing technology. By the same criterion, day-time operation is a challenge that can only be met with a combination of cutting-edge techniques in filtering and in laser sources.

Davis, Anthony B.↗