Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser induced plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Assessment Study of Small Space Debris Removal by Laser Satellites

Space debris in Earth orbit poses significant danger to satellites, humans in space, and future space exploration activities. In particular, the increasing number of unidentifiable objects, smaller than 10 cm, presents a serious hazard. Numerous technologies have been studied for removing unwanted objects in space. Our approach uses a short wavelength laser stationed in orbit to vaporize these small objects. This paper discusses the power requirements for space debris removal using lasers. A short wavelength laser pumped directly or indirectly by solar energy can scan, identify, position, and illuminate the target, which will then be vaporized or slow down the orbital speed of debris by laser detonation until it re-enters the atmosphere. The laser-induced plasma plume has a dispersive motion of approximately 105 m/sec with a Lambertian profile in the direction of the incoming beam [1-2]. The resulting fast ejecting jet plume of vaporized material should prevent matter recombination and condensation. If it allows any condensation of vaporized material, the size of condensed material will be no more than a nanoscale level [3]. Lasers for this purpose can be indirectly pumped by power from an array of solar cells or directly pumped by the solar spectrum [4]. The energy required for vaporization and ionization of a 10 cm cube (~ 2700 gm) of aluminum is 87,160 kJ. To remove this amount of aluminum in 3 minutes requires a continuous laser beam power of at least 5.38 MW under the consideration of 9% laser absorption by aluminum [5] and 5% laser pumping efficiency. The power needed for pumping 5.38 MW laser is approximately 108 MW, which can be obtained from a large solar array with 40% efficiency solar cells and a minimal area of 450 meters by 450 meters. This solar array would collect approximately 108 MW. The power required for system operation and maneuvering can be obtained by increasing solar panel size. This feasibility assessment covers roughly the power requirement, laser system, and a potential operational scenario.

Choi, Sang H.↗
NASA NTRS1974

Extreme ultraviolet spectra of highly ionized oxygen and fluorine

The foil-excitation method has been used to study the extreme ultraviolet spectra of highly ionized oxygen and fluorine. Several previously unreported lines in heliumlike fluorine are reported and other newly reported lines in heliumlike oxygen have been measured to higher accuracy. Included in the measurements are certain heliumlike oxygen transitions of significance in interpretation of solar-flare spectral observations. The wavelength determinations are usually in good agreement with calculated results which includes relativistic corrections, but discrepancies arise when nonrelativistic calculations are used. A comparison of the present results and those recently obtained by theta-pinch and laser-induced plasma sources is made for both heliumlike and lithiumlike ions; a few discrepancies occur, with results in most cases in better agreement with relativistically corrected calculations. Certain unidentified lines in the spectra may be attributable to radiative transitions between quartet states of lithiumlike ions.

Pegg, D. J.↗
NASA NTRS1978

Shock tube and shock wave research; Proceedings of the Eleventh International Symposium, University of Washington, Seattle, Wash., July 11-14, 1977

Papers are presented on the applications of shock-wave technology to the study of hydrodynamics, the use of the pressure-wave machine for charging diesel engines, and measurements of the heat-transfer rate in gas-turbine components. Consideration is given to shock propagation along 90-degree bends, the explosive dissemination of liquids, and rotational and vibrational relaxation behind weak shock waves in water vapor. Shock phenomena associated with expansion flows are described and stratospheric-related research using the shock tube is outlined. Attention is given to shock-wave ignition of magnesium powders, Mach reflection and boundary layers, and transition in the shock-induced unsteady boundary layer on a flat plate. Shock-tube measurements of induction and post-induction rates for low-Btu gas mixtures are presented and shock-initiated ignition in COS-N2O-Ar mixtures is described. Cluster growth rates in supersaturated lead vapor are presented and a study of laser-induced plasma motion in a solenoidal magnetic field is reviewed.

Ahlborn, B.↗
NASA NTRS1987

Optical efficiencies of lightning in planetary atmospheres

The first simulations of lightning in planetary atmospheres by laser-induced plasmas are reported. These simulations show that the fraction of the energy in lightning discharge channels that is radiated in the visible spectrum is similar for earth, Venus, and Titan, but quite different for Jupiter. One implication of these results is that the amount of trace gases produced by lightning in the Jovian atmosphere must be larger than previously estimated.

Borucki, W. J.↗
NASA NTRS1988

Systems report for payload G-652: Project origins

Experiments conducted to investigate possible hardware configurations and methodologies for a Get Away Special payload designated G-652 are discussed. Test data collected from the operation of a free electron laser wiggler using simulated ram glow phenomenon are described. Results of an experiment to synthesize organic compounds within a primordial atmosphere using a laser induced plasma are discussed. An experiment is described which utilized neutron bombardment to assess the risk of genetic alterations in embyros in space.

Bellina, J.↗
NASA NTRS1992

Time resolved simulation of lightning by LIP

Results of time-resolved spectra of lightning simulation in air by laser-induced plasma (LIP) are reported. The measured electron temperatures varied from 17,000 +/-1000 K at 600 ns to 12,000 +/-1000 K at 4 microsec after the ignition of the plasma. Electron densities in the plasma varied from (7.0 +/-1.4) x 10 exp 17/cu cm to (9.0 +/-1.8) x 10 exp 16/cu cm for the above times. A comparison of state variables for LIP and natural lightning is presented. Immediately following the ignition, both natural lightning and LIP are found to reach temperatures in excess of 16,000 K and relax to ambient pressure with different rates. They are expected to approach the 2000-4000-K temperature range, which is important to chemical synthesis, in an asymptotically similar fashion.

Jebens, D. S.↗
NASA NTRS2001

Flame Synthesis of Single- and Multi-Walled Carbon Nanotubes and Nanofibers

Metal-catalyzed carbon nanotubes are highly sought for a diverse range of applications that include nanoelectronics, battery electrode material, catalysis, hydrogen storage media and reinforcing agents in polymer composites. These latter applications will require vast quantities of nanotubes at competitive prices to be economically feasible. Moreover, reinforcing applications may not require ultrahigh purity nanotubes. Indeed, functionalization of nanotubes to facilitate interfacial bonding within composites will naturally introduce defects into the tube walls, lessening their tensile strength. Current methods of aerosol synthesis of carbon nanotubes include laser ablation of composite targets of carbon and catalyst metal within high temperature furnaces and decomposition of a organometallics in hydrocarbons mixtures within a tube furnace. Common to each approach is the generation of particles in the presence of the reactive hydrocarbon species at elevated temperatures. In the laser-ablation approach, the situation is even more dynamic in that particles and nanotubes are borne during the transient cooling phase of the laser-induced plasma for which the temperature far exceeds that of the surrounding hot gases within the furnace process tube. A shared limitation is that more efficient methods of nanoparticle synthesis are not readily incorporated into these approaches. In contrast, combustion can quite naturally create nanomaterials such as carbon black. Flame synthesis is well known for its commercial scalability and energy efficiency. However, flames do present a complex chemical environment with steep gradients in temperature and species concentrations. Moreover, reaction times are limited within buoyant driven flows to tens of milliseconds. Therein microgravity can greatly lessen temperature and spatial gradients while allowing independent control of flame residence times. In preparation for defining the microgravity experiments, the work presented here focuses on the effect of catalyst particle size and reactant gas in 1g.

VanderWal, R. L.↗
NASA NTRS1996

Spectral Irradiance Measurements of Simulated Lightning in Planetary Atmospheres

Optical emissions from lightning provide information to estimate the altitude, latitude and longitude of lightning storms, the energy of the discharges, and the production of important trace species such as HCN and C2H2. Knowledge of the spectra of planetary lightning is needed to deduce the total energy dissipated by lightning (and thereby, the production of trace gases) and to help design experiments to detect and track lightning storms. Measurements of the spectral irradiance from approximately 380 to 820 nm are reported for laboratory simulations of lightning in the atmospheres of Venus, Jupiter, and Titan. In our laboratory, laser-induced plasmas (LIP) are used to simulate lightning discharges. This technique avoids contamination of the spectra by elect-ode material and maintains a safe environment while allowing the use of flammable gases, such as hydrogen and methane, found in outer planet atmospheres. The observations were made at I and 5 bars pressure for Venus and Jupiter and at 1 bar for the Titan mixture. At a pressure of one bar, our results show prominent lines from H(sub alpha), H(sub beta), H(sub gamma), and H(sub delta) lines of the Balmer Series of atomic hydrogen, a single line from Helium at 588 nm and strong continuum radiation. At pressures of 5 bars, the H(sub alpha) and H(sub beta) lines are wider, the H(sub gamma), and H(sub delta) lines merge into the continuum because of pressure broadening, and the helium line at 588 nm is no longer visible. The observed spectra of simulated lightning in the venusian atmosphere at 1 and 5 bars shows that the OI multiplet at 777.7 nm dominates the spectra, but weak features due to atomic carbon and singly excited and singly ionized oxygen atoms are also visible. Although lightning has not yet been observed on Titan, it conceivable that some form of lightning discharge could be occurring. Therefore experiments on a Titan atmosphere mixture were conducted. The most prominent features seen in the simulated spectra are the H(sub alpha) at 656 nm. from the dissociation of the methane and two strong features at 740 and 820 nm from singly excited nitrogen atoms. Most of the features between 400 and 656 nm are due to ionized nitrogen atoms. A broad, highly structured feature centered near 389 nm is molecular band radiation from CN molecules formed in the cooling plasma of atomic nitrogen, carbon, and hydrogen. It is observed in the lightning simulations of both the venusian and Titan atmospheres, For Venus, Jupiter, and Titan, narrow spectral features that are ideal for detecting lightning in the presence of sunlight are present in the spectra. These features could allow lightning to be detected and tracked by Earth-based instruments.

Borucki, W. J.↗
NASA NTRS2002

Prebiotic Processing induced by Comet and Meteor Impact

In their study of organic synthesis from impact shocks using the laser-induced-plasma (LIP) technique, McKay and Borucki(l) found that organic synthesis preferentially occurred in a reducing gas mixture rich in methane, and not in a mixture rich in carbon dioxide. This result means chemical models based on the thermodynamical equilibrium approach do not apply to shock chemistry. In this study, we employ the technique of reacting flow, i.e., chemical kinetics in a fluid flow, to simulate the chemistry occurring in LIP and in the wake region from comet or meteor impact. Three different air compositions have been used: (1) 1/3 CO2 and 2/3 H2, (2) pure CH4, and (3) 1/4 CH4, 1/4 CO2, and 1/2 H2O. The stoichiometric ratio of gas mixtures (1) and (3) are kept the same. For (1) we obtain equal mole fractions of CO and H2O as the major products and for (2) C2H2 is the major product. In both cases our results are in agreement with Ref. (1). For (3) we find an interesting case where the nature of chemicals produced to be critically dependent on the flowfield temperature. At the higher temperature part of the wake region, CO and H2O are the dominant products, whereas in the cooler region C2H2 is the dominant product. Further studies of these reactions, as well as for the gas mixture including N2, are being pursued.

Dateo, Christopher E.↗
NASA NTRS2003

Effects of Two-Pulse Sequencing on Characteristics of Elementary Propellants for Ablative Laser Propulsion

This work continues on previous investigations of elementary propellants for Ablative Laser Propulsion (ALP). This paper details the experimental methods used for alignment of a non-colinear temporal pulse splitting apparatus. Spatial coincidence of the separate pulses is established, the pulses are delayed, and first data is reported on this pulse spacing effect on time-of-fight (TOF) measurements. This includes ion velocity and number density measurements, and this data is compared to results from a previous work. Also, first data on the experimental determination of the time required for the laser-induced plasma to become purely reflective to incident pulses is presented.

Thompson, M. Shane↗
NASA NTRS1994

Laser-Induced Fluorescence Helps Diagnose Plasma Processes

Technique developed to provide in situ monitoring of rates of ion sputter erosion of accelerator electrodes in ion thrusters also used for ground-based applications to monitor, calibrate, and otherwise diagnose plasma processes in fabrication of electronic and optical devices. Involves use of laser-induced-fluorescence measurements, which provide information on rates of ion etching, inferred rates of sputter deposition, and concentrations of contaminants.

Beattie, J. R.↗
NASA NTRS1979

Research on fission induced plasmas and nuclear pumped lasers at the Los Alamos Scientific Laboratory

A program of research on gaseous uranium and uranium plasmas is being conducted at The Los Alamos Scientific Laboratory under sponsorship of the National Aeronautics and Space Administration. The objective of this work is twofold: (1) to demonstrate the proof of principle of a gaseous uranium fueled reactor, and (2) pursue fundamental research on nuclear pumped lasers. The relevancy of the two parallel programs is embodied in the possibility of a high-performance uranium plasma reactor being used as the power supply for a nuclear pumped laser system. The accomplishments in the two above fields are summarized

Helmick, H. H.↗
NASA NTRS1992

Plasma erosion rate diagnostics using laser-induced fluorescence

An optical technique for measuring the sputtering rate of a molybdenum surface immersed in a xenon plasma has been developed and demonstrated. This approach, which may be useful in real-time wear diagnostics for ion thrusters, relies on laser-induced fluorescence to determine the density of sputtered molybdenum atoms.

Gaeta, C. J.↗
NASA NTRS2015

Time-Frequency Analysis of Boundary-Layer Instabilites Generated by Freestream Laser Perturbations

A controlled disturbance is generated in the freestream of the Boeing/AFOSR Mach-6 Quiet Tunnel (BAM6QT) by focusing a high-powered Nd:YAG laser to create a laser-induced breakdown plasma. The plasma then cools, creating a freestream thermal disturbance that can be used to study receptivity. The freestream disturbance convects down-stream in the Mach-6 wind tunnel to interact with a flared cone model. The adverse pressure gradient created by the flare of the model is capable of generating second-mode instability waves that grow large and become nonlinear before experiencing natural transition in quiet flow. The freestream laser perturbation generates a wave packet in the boundary layer at the same frequency as the natural second mode, complicating time-independent analyses of the effect of the laser perturbation. The data show that the laser perturbation creates an instability wave packet that is larger than the natural waves on the sharp flared cone. The wave packet is still difficult to distinguish from the natural instabilities on the blunt flared cone.

Chou, Amanda↗
NASA NTRS1991

Computer modeling of pulsed CO2 lasers for lidar applications

The experimental results will enable a comparison of the numerical code output with experimental data. This will ensure verification of the validity of the code. The measurements were made on a modified commercial CO2 laser. Results are listed as following. (1) The pulse shape and energy dependence on gas pressure were measured. (2) The intrapulse frequency chirp due to plasma and laser induced medium perturbation effects were determined. A simple numerical model showed quantitative agreement with these measurements. The pulse to pulse frequency stability was also determined. (3) The dependence was measured of the laser transverse mode stability on cavity length. A simple analysis of this dependence in terms of changes to the equivalent fresnel number and the cavity magnification was performed. (4) An analysis was made of the discharge pulse shape which enabled the low efficiency of the laser to be explained in terms of poor coupling of the electrical energy into the vibrational levels. And (5) the existing laser resonator code was changed to allow it to run on the Cray XMP under the new operating system.

Spiers, Gary D.↗
NASA NTRS2018

Effectiveness of Surface Treatment Techniques for Composite Bonding with Different Contamination Levels

Various surface treatment techniques have been developed to promote adhesive bond performance for composite structural components in aerospace applications. The condition of the pre-bond surface is critical to achieving desirable bond quality. Contamination on bonding surfaces is well recognized as a major threat to ultimate bond performance. Variation in contamination level has brought additional challenges into manufacturing process control. High fidelity surface treatment techniques are required for effective removal of contaminants over a wide range of contamination levels. In this study, a common contaminant, i.e. silicone mold release, was introduced to pre-bond composite surfaces with different concentrations. Plasma and laser surface treatment techniques were performed and their effectiveness in restoring and enhancing desirable bond quality was investigated. Surface characterization techniques, including water contact angle goniometry, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, were conducted to assess the condition of contaminated surfaces and the improvement induced by plasma and laser surface treatments. Failure modes from a customized double cantilever beam test were investigated before and after surface treatments. Fundamental mechanisms of plasma and laser surface treatments on the composite bonding surfaces were also investigated.

Fang, Xiaomei↗
NASA NTRS1987

Pulsed source of energetic atomic oxygen

A pulsed high flux source of nearly monoenergetic atomic oxygen was designed, built, and successfully demonstrated. Molecular oxygen at several atmospheres pressure is introduced into an evacuated supersonic expansion nozzle through a pulsed molecular beam valve. An 18 J pulsed CO2 TEA laser is focused to intensities greater than 10(9) W/sq cm in the nozzle throat to generate a laser-induced breakdown. The resulting plasma is heated in excess of 20,000 K by a laser supported detonation wave, and then rapidly expands and cools. Nozzle geometry confines the expansion to provide rapid electron-ion recombination into atomic oxygen. Average O atom beam velocities from 5 to 13 km/s were measured at estimated fluxes to 10(18) atoms per pulse. Preliminary materials testing has produced the same surface oxygen enrichment in polyethylene samples as obtained on the STS-8 mission. Scanning electron microscope examinations of irradiated polymer surfaces reveal an erosion morphology similar to that obtained in low Earth orbit, with an estimated mass removal rate of approx. 10(-24) cu cm/atom. The characteristics of the O atom source and the results of some preliminary materials testing studies are reviewed.

Caledonia, George E.↗