SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A new method is presented for the calculation of heats of formation, lattice parameters and cohesive energies of binary alloys. The method is applied to some fcc alloys and compared with experimental data, as well as other semiempirical results.
Prototypical single-crystal NiAlCrX superalloys were studied to examine the effects of the common major alloying elements, Co, Mo, Nb, Ta, Ti, and W, on yielding behavior. The alloys contained about 10 at. pct Cr, 60 vol pct of the gamma' phase, and about 3 at. pct of X in the gamma'. The critical resolved shear stresses (CRSSs) for octahedral and primary cube slip were measured at 760 C, which is about the peak strength temperature. The CRSS(sub oct) and CRSS(sub cube) are discussed in relation to those of Ni, (Al, X) gamma' alloys taken from the literature and the gamma'/gamma lattice mismatch. The CRSS(sub oct) of the gamma + gamma' alloys reflected a similar compositional dependence to that of both the CRSS(sub cube) of the gamma' phase and the gamma'/gamma lattice parameter mismatch. The CRSS(sub cube) of the gamma + gamma' alloys also reflected the compositional dependence of the gamma'/gamma mismatch, but bore no similarity to that of CRSS(sub cube) for gamma' alloys since it is controlled by the gamma matrix. The ratio of CRSS(sub cube)/CRSS(sub oct) was decreased by all alloying elements except Co, which increased the ratio. The decrease in CRSS(sub cube)/CRSS(sub oct) was related to the degree in which elements partition to the gamma' rather than the gamma phase.
Intrinsic properties of a compound (e.g. electronic structure, crystallographic structure, optical and magnetic properties) define notably its chemical and physical behavior. In the case of nanomaterials, these fundamental properties depend on the occurrence of quantum mechanical size effects and on the considerable increase of the surface to bulk ratio. However, the literature on this size-dependence and on the involved mechanisms is quite elusive and scarce. Here, we explore the size-dependence of both crystal and electronic properties of CeO2 nanoparticles (NPs) with different sizes by state-of-the art spectroscopic techniques. XRD, XPS and HERFD-XANES demonstrate that the as-synthesized NPs crystallize in the fluorite structure and they are predominantly composed of CeIV ions. The strong dependence of the lattice parameter with the NPs size was attributed to the presence of adsorbed species at the NPs surface thanks to FTIR and TGA measurements. In addition, the size-dependence of the eg level in the Ce LIII XANES spectra was experimentally observed by HERFD-XANES and confirmed by theoretical calculations.
A portion of the Muon g-2 Storage Ring electric system, which provides vertical beam focusing, exhibited an unexpected time dependence that produced a characteristic evolution of the stored beam during Run-1 of the Muon g-2 Experiment at Fermilab (E989). A method to reconstruct the Run-1 electric guide fields has been developed, which is based on a numerical model of the muon storage ring and optimization algorithms supported by COSY INFINITY. This method takes beam profile measurements from the Muon g-2 straw tracking detectors as input, and it produces a full reconstruction of the time-dependent fields. The fields can then be used for the reproduction of detailed beam tracking simulations and the calculation of ring lattice parameters for acceptance studies and systematic error evaluations.
Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs. The term EE (8% > 235 U > 5%) is used in this report to refer to a subset of high assay low-enriched uranium (HALEU) that is considered usable in commercial US LWRs in the near term. ATF features are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current maximum pin burnup limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. To prepare for and support these potential changes, the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases: this report summarizes the findings of Phase 1, which focuses on the lattice physics parameter and used fuel isotopic changes for a conventional Westinghouse 17×17 pressurized water reactor (PWR) design. The primary investigation tool is the SCALE Polaris code using the SCALE 56-group Evaluated Nuclear Data File (ENDF)/B-VII.1 cross sections. The goal of the current work is to (1) identify and explain important effects of EE and HBU (reactivity, lattice physics, and isotopic effects) assuming that PWR fuel design and usage remain similar to those for current enrichment fuel, (2) provide limited code-to-code comparisons with higher order cross section libraries and/or codes, and (3) identify any apparent anomalous trends in the results for further investigation.
Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs to further improve reactor safety and plant economics. Extended fuel enrichments above 5% 235 U pin enrichment and up to 10% 235 U are a subset of high assay low-enriched uranium (HALEU) that may be deployed in commercial US LWRs in the near term. ATF features, such as cladding coatings or alternative cladding materials, are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. As part of the US Nuclear Regulatory Commission (NRC) agreement number 31310019N0008, “SCALE Code Development, Assessment and Maintenance,” the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases, and this report summarizes the findings of the Phase 1 work, which focuses on lattice physics parameter and used fuel isotopic changes for a conventional GE14 10 x 10 boiling water reactor (BWR) design with GNF-2 part length rod patterns to model a modern BWR assembly design.
The goal of this study is to analyze the effect of radial void fraction distribution, considered at three degrees of fidelity, on lattice and 2-group homogenized cross sections. The novelty of this work lies in its use of experimentally-determined radial void fraction distributions which allows for fine-scale coolant density data with no predictive uncertainty and which could be prohibitively expensive to simulate over the range of operational parameters used in the experiments. The experimentally-determined radial void fraction distributions are also characterized using a statistical tool called a semi-variogram in order to determine the scale of continuity. Void fraction distributions are averaged at the lattice and subchannel level for comparison with the fine-scale model. Models averaged at the subchannel and lattice level show a difference in about 68% of the time. Also, by comparing 2-group homogenized cross-sections, the differences between the subchannel and homogeneous cases are measurable.
Commercial light water reactor (LWR) operators and fuel vendors in the United States (US) are pursuing changes to the reactor fuel that include increased enrichment and accident-tolerant fuel (ATF) designs. Enrichments under consideration are between 5 wt % and 10 wt % 235 U, which are a subset of high-assay low-enriched uranium fuels. ATF features are designed to improve fuel system performance under accident conditions. With increased enrichment, fuel cycle economics can be improved if fuel can be licensed for higher burnup (HBU) than typical current limits (e.g., 62 GWd/MTU maximum fuel pin).
The parameter values measured are in agreement with those reported by Mazelsky and Lubell (1963) and data of Bis and Dixon (1969). The measurements for SnTe introduce a large amount of data into a defect model analysis that shows that the ratio of the number of holes per tin-vacancy acceptor to the 77 K Hall factor is independent of the apparent hole concentration. The measurements reveal some interesting problems in handling the Sn-rich alloys in fine powder form due to the uptake of oxygen.
Explore the source record for details and available documents.
The inherent errors introduced by the algorithm of standard procedures of evaluation of powder diffractograms of nanopowders are shown. The implications of the errors are discussed and illustrated based on the results reported in the literature.
Inherent errors introduced by the algorithm of standard procedures of evaluation of powder diffractograms when applied for nanopowders are shown. The implications of the errors are discussed in connection with some results reported in the literature. Alternate methodology of evaluation of powder diffractograms of nanocrystals is presented.
Explore the source record for details and available documents.
Undoped (B 4 C), B rich (B 5.5 C), and B/Si co-doped (Si-B 6.5 C) boron carbides were annealed at 500 °C for up to 21 days to investigate the thermal stability of primary dopants, B and Si. Structural changes associated with dedoping were investigated by X-ray diffraction (XRD) and Raman spectroscopy. The stable phase B 4 C showed no microstructural or lattice parameter changes. Similarly, lattice parameters of B 5.5 C remained constant, suggesting that B dopant is stable at the given conditions. However, the shortened lattice parameters and reduced Si content of Si-B 6.5 C over the annealing time indicated that Si dopant was in a metastable state at the annealing temperature. Consequently, Si dedoping led to an increase in amorphization (a loss of local crystalline order) which degrades the ballistic performance of boron carbide. The insight highlights the importance of Si dopant in boron carbide and suggests that rapid processing may be necessary to retain more silicon for better performance.
Alloying and site ordering play complementary roles in dictating a material’s properties. However, deconvolving the impacts of these separate phenomena can be challenging. In this work, we simulate structures of Zn(Sn,Ge)N 2 with varied Sn content and site ordering to determine the impacts of order and composition on structural and electronic properties. We assess the formation enthalpy, lattice parameters, elastic constants, spontaneous polarization, and piezoelectric coefficients. In mostly disordered structures (order parameters ranging from 0.2 to 0.4), the formation enthalpy exhibits local extrema as a function of the order parameter, deviating from the more linear trends seen in both fully disordered and fully ordered systems. This anomalous deviation from the otherwise linear trend in formation enthalpy with order manifests in each of the other properties calculated. This range of order parameters of interest may be caused by a transition in the ordering of the quaternary material similar to phase changes seen in ternary compounds but stretched over a region inclduing 20% of the order parameter range. Most parameters calculated are more sensitive to order than to composition in the limited composition range tested; however, the lattice parameter c, piezoelectric coefficient e 33 , and elastic moduli C 12 , C 13 , and C 23 are more sensitive to composition. Of the properties compared, the piezoelectric coefficients are influenced most significantly by changes in both the composition and order parameter. Lattice parameters undergo the smallest changes with order and composition, but these small differences appear to impart large trends in the other properties. Better understanding the effects of disorder and group IV alloying in Zn(Sn,Ge)N 2 allows for more accurate modeling of characteristics of this material system for solid state lighting and other applications.
The effect of the chemical state of the surface of nanoparticles on the relaxation in the near-surface layer was examined using the concept of the apparent lattice parameter (alp) determined for different diffraction vectors Q. The apparent lattice parameter is a lattice parameter determined either from an individual Bragg reflection, or from a selected region of the diffraction pattern. At low diffraction vectors the Bragg peak positions are affected mainly by the structure of the near-surface layer, while at high Q-values only the interior of the nano-grain contributes to the diffraction pattern. Following the measurements on raw (as prepared) powders we investigated powders cleaned by annealing at 400C under vacuum, and the same powders wetted with water. Theoretical alp-Q plots showed that the structure of the surface layer depends on the sample treatment. Semi-quantitative analysis based on the comparison of the experimental and theoretical alp-Q plots was performed. Theoretical alp-Q relations were obtained from the diffraction patterns calculated for models of nanocrystals with a strained surface layer using the Debye functions.
With a Curie temperature just above room temperature, AlFe 2 B 2 is a useful magnetocaloric material composed of earth-abundant elements. Here, we employ temperature-dependent high-resolution synchrotron X-ray diffraction to establish with high certainty that the paramagnetic to ferromagnetic transition in AlFe 2 B 2 is of second order, showing no discontinuity in lattice parameters or cell volume. Nevertheless, the lattice parameters undergo anisotropic changes across the transition with distinct differences in the thermal expansion coefficients. While the $a$ and $b$ lattice parameters show a positive thermal expansion, $c$ shows a negative thermal expansion. We link these changes to the respective interatomic distances to determine the contribution of magnetism to the anisotropic structural evolution. The work underpins the possible role of magnetostructural coupling in driving the magnetocaloric effect in AlFe 2 B 2 .
The high-pressure equation of state (EOS) of energetic materials (EMs) is important for continuum and mesoscale models of detonation performance and initiation safety. Additionally, obtaining a high-fidelity EOS of the insensitive EM 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) has proven to be difficult because of challenges in experimental characterization at high pressures (HPs). In this work, powder X-ray diffraction patterns were fitted using the recently discovered monoclinic I2/a phase above 4 GPa, which shows that TATB is less compressible than when indexed with the triclinic $P\bar{1}$ phase. First-principles calculations were performed with Perdew–Burke–Ernzerhof (PBE) and PBE0 functionals including thermal effects using the $P\bar{1}$ phase. PBE0 improves the description of hydrogen bonding and thus predicts accurate planar a and b lattice parameters under ambient conditions. However, discrepancies in the predicted lattice parameters above 4–10 GPa compared with experimental measurements indexed with $P\bar{1}$ are further evidence of a structural modification at high pressure. Layer sliding defects are formed during molecular dynamics simulations, which induces an anharmonic effect on the thermal expansion of the c lattice parameter. In short, the results provide several insights into determining high-fidelity EOS parameters for TATB and other molecular crystals.