Search NASA⌕ Search

SEARCH · Search NASA

Results for “lift modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Optimal trajectories for aeroassisted orbital transfer

Consideration is given to classical and minimax problems involved in aeroassisted transfer from high earth orbit (HEO) to low earth orbit (LEO). The transfer is restricted to coplanar operation, with trajectory control effected by means of lift modulation. The performance of the maneuver is indexed to the energy expenditure or, alternatively, the time integral of the heating rate. Firist-order optimality conditions are defined for the classical approach, as are a sequential gradient-restoration algorithm and a combined gradient-restoration algorithm. Minimization techniques are presented for the aeroassisted transfer energy consumption and time-delay integral of the heating rate, as well as minimization of the pressure. It is shown that the eigenvalues of the Jacobian matrix of the differential system is both stiff and unstable, implying that the sequential gradient restoration algorithm in its present version is unsuitable. A new method, involving a multipoint approach to the two-poing boundary value problem, is recommended.

Miele, A.↗
NASA NTRS1985

An exploratory study of apex fence flaps on a 74 deg delta wing

An exploratory wind tunnel investigation was performed to observe the flow field effects produced by vertically deployed apex fences on a planar 74 degree delta wing. The delta shaped fences, each comprising approximately 3.375 percent of the wing area, were affixed along the first 25 percent of the wing leading edge in symmetric as well as asymmetric (i.e., fence on one side only) arrangements. The vortex flow field was visualized at angles of attack from 0 to 20 degrees using helium bubble and oil flow techniques; upper surface pressures were also measured along spanwise rows. The results were used to construct a preliminary description of the vortex patterns and induced pressures associated with vertical apex fence deployment. The objective was to obtain an initial evaluation of the potential of apex fences as vortex devices for subsonic lift modulation as well as lateral directional control of delta wing aircraft.

Wahls, R. A.↗
NASA NTRS1984

Approximate solutions to minimax optimal control problems for aeroassisted orbital transfer

The maneuver considered in the present investigation involves the coplanar transfer of a spacecraft from a high earth orbit (HEO) to a low earth orbit (LEO). HEO can be a geosynchronous earth orbit (GEO). The basic concept utilized involves the hybrid combination of propulsive maneuvers in space and aerodynamic maneuvers in the sensible atmosphere. The considered type of flight is also called synergetic space flight. With respect to the atmospheric part of the maneuver, trajectory control is achieved by means of lift modulation. The Bolza problem of optimal control is stated, and the first-order optimality conditions for this problem are given. The one-arc approach, the two-arc approach, and the three-subarc approach are discussed. Attention is given to the Chebyshev problem of optimal control, details concerning aeroassisted orbital transfer (AOT), AOT optimization problems, and numerical experiments.

Miele, A.↗
NASA NTRS1986

Nearly-grazing optimal trajectories for aeroassisted orbital transfer

In the present treatment of optimal control problems arising in the study of coplanar aeroassisted orbital transfer, the hybrid combination of propulsive parameters in space and aerodynamic maneuvers employing lift modulation in the sensible atmosphere indicates that the optimal energy-viewpoint solution is the grazing trajectory; this trajectory is characterized by favorable values of the peak heating rate and the peak dynamic pressure. Numerical solutions are obtained by means of the sequential gradient restoration algorithm for optimal control problems. It is found that nearly-grazing trajectories yielding the least-square value of the path inclination have desirable characteristics from the standpoints of energy, heating rate, and dynamic pressure.

Miele, A.↗
NASA NTRS1988

Atmospheric maneuvering during Martian entry

A comparative-advantages study is made of two different Martian atmospheric entry maneuvers, on the basis of calculation results for the case of a vehicle with a maximum L/D ratio of 2.3. Entries from a highly elliptical Martian orbit at 5 km/sec are more difficult than those from a lower altitude and speed orbit at 3.5 km/sec, due to their more stringent guidance requirements. Efforts to reduce the deceleration for the higher speed entry by lift-modulation achieved a 40-percent reduction, but at the cost of a 50-percent decrease in lateral range. The lower-speed entry's gliding trajectory is noted to encounter a far more benign atmospheric environment.

Tauber, Michael E.↗
NASA NTRS1972

Apollo 16 Press Kit

The Apollo 16 spacecraft is scheduled for launch on Apr. 16, 1972 from Complex 39A at the Kennedy Space Center, Florida by the Saturn V launch vehicle. Crewmen are mission commander John W. Young, command module pilot Thomas K. Mattingly II and lunar module pilot Charles M. Duke Jr. Objectives of the mission, to last up to 12 days, as outlined by NASA: to perform selenological inspection, survey and sampling of materials in a preselected region of Descartes using a lunar roving' vehicle; deploy and activate Apollo surface experiments; develop man's capability to work in the lunar environment; obtain photographs of candidate exploration sites; and toconduct inflight experiments and photographic tasks in lunar orbit. Following launch, the spacecraft will reach Earth Parking Orbit and remain in orbit for about two and one-half revolutions prior to Translunar Injection. Next, the Command and Service Module docks with the Lunar Module and the spacecraft "coasts" to the moon. In orbit around the moon, the Command and Service Module/Lunar Module combination will descend to within 50,000 feet of the lunar surface before undocking. The Lunar Module will continue to descend while the Command and Service Module returns to an orbit approximately 60 miles high. Stay time on the lunar surface is scheduled for approximately 73 hours. The ascent stage of the Lunar Module then lifts the astronauts back into lunar orbit where they will dock with the Command/Service Module. The Lunar Module is jettisoned and Transearth Injection follows. Just prior to reentry into the earth's atmosphere, the Service Module is jettisoned, and the astronauts in the Command Module splashdown in the Pacific Ocean. The target point for end-of-mission splashdown is at 05 degrees 0 minutes north latitude and 158 degrees 40 minutes west longitude or approximately 985 nautical miles south of Honolulu, Hawaii. Splashdown is scheduled for Apr. 28, 1972 at 10:30 a.m. Hawaiian Standard Time (2:30 p.m. CST). Recovery forces for Apollo 16, stationed in both the Atlantic and Pacific Oceans, will consist of three ships, nine aircraft and nearly 1,700 personnel. CTF-130 (Manned Spacecraft Recovery Force, Pacific) forces will be stationed south of Hawaii. Three ships, eight helicopters and three Air Force HC-130H aircraft, and nearly 1,100 personnel, will take part. Task Force 140 (Manned Spacecraft Recovery Force, Atlantic), comprising one ship, six HC-130H aircraft, three helicopters and approximately 300 personnel, will be positioned for possible launch abort operations. Two ships in the Atlantic will also be used for acoustical testing. Other forces, primarily aircraft and personnel of the Air Force Aerospace Rescue and Recovery Service will be on alert around the world for contingency recovery support.

Source record↗
NASA NTRS2018

Studies in Support of Venus Aerocapture Utilizing Drag Modulation

Aerocapture has been extensively studied and these studies have shown the benefit for planetary exploration missions. While the traditional approach to aerocapture with lifting configurations and lift-guided modulations have been assessed to be technologically feasible, aerocapture using purely drag modulation was proposed and studied by Prof. Braun and his students. These studies show that if one can assess the feasibility of aerocapture using drag modulation at Venus, and develop tall pole technologies needed at Venus, then this concept is much easier to execute at all other relevant destinations. Based on the above finding, partnered proposals were submitted by Adam Nelessen at JPL and Ethiraj Venkatapathy at Ames in collaboration with Prof. Braun at the University of Colorado, Boulder (UCB). Under this partnership, Ames Research Center (ARC) is working to address some of the key entry technology challenges associated with drag modulation aerocapture at Venus. Drag modulation aerocapture is a simple, scalable, and likely cost-effective way to enhance planetary science missions. The approach envisioned is to design a small spacecraft, that would most likely be a secondary payload, with a removable drag skirt. The vehicle would enter the atmosphere at Venus with a low ballistic coefficient, decelerate rapidly, drop the skirt resulting in a smaller vehicle with a higher ballistic coefficient which would skip out of the atmosphere and enter into a desired orbit. ARC's role in this collaboration is multifold. First of which is to perform design studies on various pre- and post-jettison geometries utilizing a 3-DOF trajectory code to determine the aerodynamics and aerothermodynamics of the vehicles and evaluate viable thermal protection material system designs. Once these design studies are complete, Ames will then perform higher fidelity CFD and TPS sizing to further design the vehicles. Second, the multi-body separation dynamics of the drag modulation event will be explored using both CFD simulations (CART3-D and US3D) as well as possible ballistic range testing. ARC's tools and expertise have been used to assess and advise on the selection of the separating configuration. In addition to the preliminary evaluation, ARC will provide tools and expertise to UCB team members to further assess aerodynamic interactions between the separating bodies and provide guidance as to the feasibility of stable transition.

Beck, Robin↗
NASA NTRS2019

Towards Articulated Mobility and Efficient Docking for the DuAxel Tethered Robot System

Sites of increasing interest for planetary science,such as craters, cold traps, and vents lie in terrains that are inaccessible to state-of-the-art rovers. The Jet Propulsion Laboratory, in collaboration with Caltech, is actively developing a tethered mobile robot, Axel, for traversing and exploring extremely steep terrain, such as Recurring Slope Lineae on Mars and vertical pits on the Moon. However, on Mars, where landing-site uncertainty is high due to the presence of an atmosphere, Axel may need to traverse several kilometers from its lander untethered due to a finite tether carrying capacity (⇠300m). This paper proposes a novel design for a hybrid mobility system that allows a pair of Axel rovers to dock, lock, and drive long distances as a four-wheeled, articulated steering vehicle. The design improves upon prior efforts to achieve DuAxel mobility by leveraging two actuated docking mechanisms attached on opposite ends of a central module to enable ‘sit/stand’ functionality; the prior DuAxel system was limited to skid steering, which was inefficient due to Axel’s grouser-style, high-friction wheels. In the proposed system, the ‘sit’ configuration is achieved by aligning each dock parallel to the surface, allowing one Axel to detach and explore while the other remains docked and serves as a backup. While ‘sitting’, the central module rests on the ground and is outfitted with shovel-style wedges for passive anchoring to sandy terrain (an optional drill can be integrated for anchoring to rock). In order to ‘stand’, the exploring Axel reattaches, locks, and both docks are rotated until Axel’s tether caster arm is upright and the central module is lifted off the ground. Once upright, each Axel rotates about a pivot point for articulated, all-wheel steering, which is accomplished by applying differential wheel torques. The main contributions of this paper are i) a detailed systems design of the docking mechanism and central module, ii) kinematic modeling of articulated mobility and ‘sit/stand’ docking functionality, and iii) initial testing in a relevant environment to characterize the mobility of the proposed system.

Nesnas, Issa↗
NASA NTRS1986

Towards an advanced vortex flap system: The cavity flap

An extension of the vortex flap concept was explored with the aim of providing high-alpha flight control capability coupled with maneuver drag reduction for highly swept wing configurations. A retractable lower surface flap mounted on a translating hinge is proposed, allowing chordwise extension as well as deflection, the two movements being independently controlled. The frontal cavity formed by the partially extended and deflected flap captures a vortex above a certain angle of attack. The cavity vortex downwash alleviates the effective incidence of the wing leading edge, thus modulating vortex lift; at the same time, the induced suction in the cavity generates thrust. These postulated aerodynamic features of the cavity flap were validated through low speed tunnel pressure and visualization tests on a 65 deg swept oblique wing model, which also provided initial trends of the leading edge vortex alleviation and cavity suction with respect to flap extension, deflection and angle of attack. Force tests on a 60 deg delta model further showed the cavity flap L/D performance to compare favorably with the conventional vortex flap. A two segment flap arrangement with independently control led segments was envisaged for exploiting the vortex modulation capability of the cavity flap for pitch, roll and yaw control, in addition to drag reduction at high angles of attack.

Rao, D. M.↗
NASA NTRS2021

Mars 2020 Perseverance Entry Controller Design and Flight Reconstruction

On February 18th, 2021, NASA landed Perseverance on the Jezero crater (on Mars). An entry Guidance, Navigation, and Control (GNC) system delivered the vehicle to the desired landing ellipse. The navigation filter propagated position and attitude states initialized from cruise using Inertial Measurement Unit (IMU) measurements. The entry guidance modulated the lift vector through bank commands to reach the parachute deploy conditions. The entry controller commanded the propulsive Reaction Control System (RCS) to track the bank commands while doing rate damping on angle-of-attack and sideslip. This paper describes the design and the as-flown performance of the entry controller.

Way, David W.↗
NASA NTRS1991

The power induced effects module: A FORTRAN code which estimates lift increments due to power induced effects for V/STOL flight

A user friendly FORTRAN code that can be used for preliminary design of V/STOL aircraft is described. The program estimates lift increments, due to power induced effects, encountered by aircraft in V/STOL flight. These lift increments are calculated using empirical relations developed from wind tunnel tests and are due to suckdown, fountain, ground vortex, jet wake, and the reaction control system. The code can be used as a preliminary design tool along with NASA Ames' Aircraft Synthesis design code or as a stand-alone program for V/STOL aircraft designers. The Power Induced Effects (PIE) module was validated using experimental data and data computed from lift increment routines. Results are presented for many flat plate models along with the McDonnell Aircraft Company's MFVT (mixed flow vectored thrust) V/STOL preliminary design and a 15 percent scale model of the YAV-8B Harrier V/STOL aircraft. Trends and magnitudes of lift increments versus aircraft height above the ground were predicted well by the PIE module. The code also provided good predictions of the magnitudes of lift increments versus aircraft forward velocity. More experimental results are needed to determine how well the code predicts lift increments as they vary with jet deflection angle and angle of attack. The FORTRAN code is provided in the appendix.

Sandlin, Doral R.↗
NASA NTRS2008

Enabling and Enhancing Space Mission Success and Reduction of Risk through the Application of an Integrated Data Architecture

The engineering phases of design, development, test, and evaluation (DDT and E) and subsequent planning, preparation, and operation (Ops) of space vehicles in a complex and distributed environment requires massive and continuous flows of information across the enterprise and across temporal stages of the vehicle lifecycle. The resulting capabilities at each subsequent stage depend in part on the capture, preparation, storage, and subsequent provision of information from prior stages. The United States National Aeronautics and Space Administration (NASA) is currently designing a fleet of new vehicles that will replace the Space Shuttle and expand space operations and exploration capabilities. This includes the 2 stage human rated lift vehicle Ares 1 and its associated crew vehicle the Orion, and a service module; the heavy lift cargo vehicle, Ares 5, and an associated cargo stage known as the Earth Departure Stage; and a Lunar Lander vehicle that contains a descent stage, and ascent stage, and a habitation module. A variety of concurrent assorted ground operations infrastructure including software and facilities are also being developed, assorted technology and assembly designs and development for equipment such as EVA suits, life support systems, command and control technologies are also in the pipeline. The development is occurring in a distributed manner, with project deliverables being contributed by a large and diverse assortment of vendors and most space faring nations. Critical information about all of the components, software, and procedures must be shared during the DDT and E phases and then made readily available to the mission operations staff for access during the planning, preparation, and operations phases, and also need to be readily available for system to system interactions. The Constellation Data Systems Project (CxDS) is identifying the needs, and designing and deploying systems and processes to support these needs. This paper details the steps and processes that NASA is applying within the Constellation Program to manage this data and information, and to insure that the correct information is available, correctly annotated, and can be provisioned digitally to enhance response times, and support engineering analysis and anomaly resolution.

Brummett, Robert C.↗
NASA NTRS1980

US Coast Guard lightweight fire-fighting module

The U.S. Coast Guard Fire-fighting Module developed for the purpose of fighting fires in harbors and on ships is described. The module can be lifted by a dockside crane or helicopter and placed on the deck of a patrol boat or cutter for transportation to the scene of the fire. At the fire the module can be set up and put in operation by a crew of two in approximately fifteen minutes. Once in operation the module will deliver water to two fire nozzles at a pressure of 150 psi and a flow rate of 2000 gpm. Sufficient fuel is carried in the module for three hours of continuous operation. A record of the development of the fire fighting module is also presented.

Source record↗
NASA NTRS2014

Habitat Demonstration Unit (HDU) Vertical Cylinder Habitat

NASA's Constellation Architecture Team defined an outpost scenario optimized for intensive mobility that uses small, highly mobile pressurized rovers supported by portable habitat modules that can be carried between locations of interest on the lunar surface. A compact vertical cylinder characterizes the habitat concept, where the large diameter maximizes usable flat floor area optimized for a gravity environment and allows for efficient internal layout. The module was sized to fit into payload fairings for the Constellation Ares V launch vehicle, and optimized for surface transport carried by the All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) mobility system. Launch and other loads are carried through the barrel to a top and bottom truss that interfaces with a structural support unit (SSU). The SSU contains self-leveling feet and docking interfaces for Tri-ATHLETE grasping and heavy lift. A pressurized module needed to be created that was appropriate for the lunar environment, could be easily relocated to new locations, and could be docked together in multiples for expanding pressurized volume in a lunar outpost. It was determined that horizontally oriented pressure vessels did not optimize floor area, which takes advantage of the gravity vector for full use. Hybrid hard-inflatable habitats added an unproven degree of complexity that may eventually be worked out. Other versions of vertically oriented pressure vessels were either too big, bulky, or did not optimize floor area. The purpose of the HDU vertical habitat module is to provide pressurized units that can be docked together in a modular way for lunar outpost pressurized volume expansion, and allow for other vehicles, rovers, and modules to be attached to the outpost to allow for IVA (intra-vehicular activity) transfer between them. The module is a vertically oriented cylinder with a large radius to allow for maximal floor area and use of volume. The modular, 5- m-diameter HDU vertical habitat module consists of a 2-m-high barrel with 0.6-mhigh end domes forming the 56-cubicmeter pressure vessel, and a 19-squaremeter floor area. The module has up to four docking ports located orthogonally from each other around the perimeter, and up to one docking port each on the top or bottom end domes. In addition, the module has mounting trusses top and bottom for equipment, and to allow docking with the ATHLETE mobility system. Novel or unique features of the HDU vertical habitat module include the nodelike function with multiple pressure hatches for docking with other versions of itself and other modules and vehicles; the capacity to be carried by an ATHLETE mobility system; and the ability to attach inflatable 'attic' domes to the top for additional pressurized volume.

Howe, Alan↗
NASA NTRS2000

An Entry Flight Controls Analysis for a Reusable Launch Vehicle

The NASA Langley Research Center has been performing studies to address the feasibility of various single-stage to orbit concepts for use by NASA and the commercial launch industry to provide a lower cost access to space. Some work on the conceptual design of a typical lifting body concept vehicle, designated VentureStar(sup TM) has been conducted in cooperation with the Lockheed Martin Skunk Works. This paper will address the results of a preliminary flight controls assessment of this vehicle concept during the atmospheric entry phase of flight. The work includes control analysis from hypersonic flight at the atmospheric entry through supersonic speeds to final approach and landing at subsonic conditions. The requirements of the flight control effectors are determined over the full range of entry vehicle Mach number conditions. The analysis was performed for a typical maximum crossrange entry trajectory utilizing angle of attack to limit entry heating and providing for energy management, and bank angle to modulation of the lift vector to provide downrange and crossrange capability to fly the vehicle to a specified landing site. Sensitivity of the vehicle open and closed loop characteristics to CG location, control surface mixing strategy and wind gusts are included in the results. An alternative control surface mixing strategy utilizing a reverse aileron technique demonstrated a significant reduction in RCS torque and fuel required to perform bank maneuvers during entry. The results of the control analysis revealed challenges for an early vehicle configuration in the areas of hypersonic pitch trim and subsonic longitudinal controllability.

Calhoun, Philip↗