Search NASA⌕ Search

SEARCH · Search NASA

Results for “low-frequency acoustics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗
NASA NTRS1976

Correlation microphone for measuring airframe noise in large-scale wind tunnels

A correlation microphone arrangement was used in the test section of the Ames 7- by 10-Foot and 40- by 80-Foot Wind Tunnels in an attempt to reject the reverberant and wind noise. The tests in the 7- by 10-foot wind tunnel covered a frequency range from 400 Hz to 8 kHz while the tests in the 40- by 80-foot tunnel covered the range from 31.5 to 800 Hz. Examination of the experimental data plus calculations of cross-correlations due to reflective noise indicate that the correlation microphone is effective in rejecting microphone wind noise and reverberant noise even at low frequencies, and that the low-frequency background noise monitored by the correlation microphone is reflected noise with a preferred direction from the tunnel drive system. Design studies indicate that this tunnel drive noise can be reduced substantially through suitable modification of the drive fans and acoustical treatment of the nacelles that house these fans.

Ahtye, W. F.↗
NASA NTRS1961

Near-Field and Far-Field Noise Measurements for a Blowdown-Wind-Tunnel Supersonic Exhaust Jet having about 475,000 Pounds of Thrust

Near-field and far-field noise surveys were made of the supersonic The exhaust jet of the Langley 9- by 6-foot thermal structures tunnel. The jet had a thrust rating of approximately 475,000 pounds. The sound power radiated was found to be about 3.6 x 10(exp 6) watts, and on an acoustical-mechanical efficiency basis this value is in reasonable agreement with data for smaller supersonic jets and for rocket engines of other investigations. Octave-band analyses of the near-field noise show that the maximum sound pressure levels in the low-frequency bands are greatest downstream, whereas maximum sound pressure levels in the high-frequency bands were greatest near the jet exit. A comparison of near-field noise measurements is made with data previously obtained for rocket engines. Noise survey measurements of the original jet are compared with similar data obtained after the addition of a 97-foot-long exit diffuser section, and an example of the application of this facility to the problem of acoustic environmental testing of a large space capsule is cited.

Mayes, William H.↗
DOE OSTI2024

Investigation of Low-Energy Lattice Dynamics and Their Role in Superionic Na Diffusion and Ultralow Thermal Conductivity of Na 3 PSe 4 as a Solid-State Electrolyte

The atomic dynamics of Na 3 PSe 4 were investigated using a combination of neutron scattering experiments and ab initio and machine-learned molecular dynamics simulations to probe the interplay of fast ionic diffusion with atomic vibrations (phonons) of the host lattice. Our results reveal the existence of low-energy vibrational modes, simultaneously involving motions of Na + ions and framework polyanion subunits, and show that these modes become strongly overdamped in the superionic regime as they couple with the Na + hopping process. In particular, the Na+ migration energy landscape is strongly impacted by low-energy phonons derived from a soft acoustic branch of the host lattice, which modulates the diameter of the Na + diffusion channel at the bottleneck. We find that an additional factor for the enhanced Na + conductivity in Na 3 PSe 4 is the presence of Na-vacancies, which also affect the low-frequency dynamics and thermal vibration amplitudes, pointing to an interplay between Na + vacancies and host dynamics, jointly enhancing ionic diffusivity. Finally, we investigate the origin of ultralow thermal conductivities in Na 3 PSe 4 and Na 3 PS 4 using Green–Kubo simulations and find that low-energy acoustic phonon modes of the overall crystal framework provide a dominant contribution to the thermal conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

Measurement, analysis, and prediction of aircraft interior noise

Considerations of comfort of passengers and crew in light aircraft and helicopters indicate substantial benefits may be obtained by the reduction of interior noise levels. This paper discusses an ongoing research effort to reduce interior noise in such vehicles. Data from both field and laboratory studies for a light aircraft are presented. The laboratory data indicate that structural vibration is an efficient source of interior noise and should be considered in the reduction of interior noise. Flight data taken on a helicopter before and after installation of acoustic treatment demonstrate that over 30 dB of noise reduction can be obtained in certain portions of the spectra. However, subjective evaluations of the treated vehicle indicate that further reductions in interior noise are desirable. An existing interior noise prediction method which was developed for large jet transports was applied to study low-frequency noise in a light aircraft fuselage. The results indicate that improvements in the analytical model may be necessary for the prediction of interior noise of light aircraft.

Howlett, J. T.↗
NASA NTRS1954

Investigation of Noise Field and Velocity Profiles of an Afterburning Engine

Sound pressure levels, frequency spectrum, and jet velocity profiles are presented for an engine-afterburner combination at various values of afterburner fuel - air ratio. At the high fuel-air ratios, severe low-frequency resonance was encountered which represented more than half the total energy in the sound spectrum. At similar thrust conditions, lower sound pressure levels were obtained from a current fighter air craft with a different afterburner configuration. The lower sound pressure levels are attributed to resonance-free afterburner operation and thereby indicate the importance of acoustic considerations in afterburner design.

North, Warren J.↗
DOE OSTI2026

Coherent and Dynamic Small Polaron Delocalization in CuFeO 2

Small polarons remain a bottleneck in realizing efficient transition metal oxide devices. Routes to engineer small polaron coupling to electronic states and lattice modes to control carrier localization remain unclear. Here, we measure small polaron formation in CuFeO 2 using transient extreme ultraviolet reflection spectroscopy and compare to theoretical predictions in realistically parametrized Holstein models, demonstrating that polaron localization depends on coupling to high-frequency versus low-frequency phonon bath components. We measure small polaron formation on a comparable ∼100 fs timescale to other Fe(III) compounds. Dynamic delocalization of the polaron follows formation through a coherent lattice expansion between Fe–O layers and charge-sharing with surrounding Fe(IV) states. Simulations reveal two major factors dictate polaron formation timescales: phonon density and reorganization energy distributions between acoustic and optical modes, matching experimental findings. Our work shows how electronic-structural coupling in a polaron-host material can be leveraged to suppress polaronic effects for various applications.

Hematite↗
NASA NTRS1975

Cold-flow acoustic evaluation of a small scale, divergent, lobed nozzle for supersonic jet noise suppression

A supersonic jet noise suppressor was tested with cold flow for acoustic and thrust characteristics at nozzle- to atmospheric-pressure ratios of 1.5 to 4.0. Jet noise suppression and spectral characteristics of the divergent, lobed, suppressor (DLS) nozzle with and without an ejector are presented. Suppression was obtained at nozzle pressure ratios of 2.5 to 4.0. The largest, maximum-lobe, sound pressure level suppression with a hard-wall ejector was 14.6 decibels at a nozzle pressure ratio of 3.5. The thrust loss was 2 percent. In general, low-frequency jet noise was suppressed, leaving higher frequencies essentially unchanged. Without the ejector the nozzle showed a thrust loss of 11 percent together with slightly poorer noise suppression.

Huff, R. G.↗
DOE OSTI2025

Detection of a Space Capsule Entering Earth’s Atmosphere with Distributed Acoustic Sensing (DAS)

On 24 September 2023, the Origins, Spectral Interpretation, Resource Identification, and Security-Regolith Explorer sample return capsule (SRC) entered Earth’s atmosphere after successfully collecting samples from an asteroid. The known trajectory and timing of this return provided a rare opportunity to strategically instrument sites to record geophysical signals produced by the capsule because it travelled at hypersonic speeds through the atmosphere. For this work, we deployed two distributed acoustic sensing (DAS) interrogators to sample over 12 km of surface-draped fiber-optic cables, as well as six collocated seismometer-infrasound sensor pairs, spread across two sites near Eureka, Nevada. This campaign-style rapid deployment is the first reported recording of an SRC re-entry with any distributed fiber-optic sensing technology. The DAS interrogators recorded an impulsive arrival with an extended coda which had features that were similar to recordings from both the seismometers and infrasound sensors. While the signal-to-noise ratio of the DAS data was lower than the seismic-infrasound data, the extremely dense spacing of fiber-optic sensors allowed for more phases to be clearly distinguished and the visualization of the continuous transformation of the wavefront as it impacted the ground. Unexpectedly, the DAS recordings contain less low-frequency content than is present in both the seismic and infrasound data. The deployment conditions strongly affected the recorded DAS data; in particular, we observed that fiber selection and placement exert strong controls on data quality.

58 GEOSCIENCES↗
DOE OSTI2025

Continuous surface-to-distributed acoustic sensor snapshots explain reactivation of individual natural fractures during an unconventional reservoir stimulation

ABSTRACT Fiber-optic sensing technologies allow petroleum engineering teams to detect hydraulic fracture interaction with boreholes during unconventional reservoir stimulation. In combination with high-repeatability seismic sources, the same distributed acoustic sensors (DASs) enable vertical seismic profiling (VSP) of the fracture evolution away from the boreholes. We discovered clear signatures of seismic scattering on activated fractures during nine days of continuous seismic monitoring of the fracturing stages at the Austin Chalk/Eagle Ford Field Laboratory. The present study applies a novel approach for quantitative analysis of the scattering events in terms of the evolution of the geometry and elastic stiffness of individual fractures. Our characterization strategy sequentially refines the fracture models: from a stack of 1D soft layers to 3D rectangular inclusions. First, we estimate the number of fracture locations and reflectivity using a modified sparse-spike deconvolution of the stacked VSP traces. The fracture set consists of five fractures spaced by 15–30 m with a reflectivity of approximately 1%. Then, we develop a scattering integral method to refine these estimates along with an inversion of the fracture top and bottom for each monitoring vintage. We find that, initially, some of the fractures are located above the monitoring fiber with the height of approximately 100 m. Then we integrate the seismic interpretation with the low-frequency DAS and pressure and microseismic monitoring to reconstruct the activation process of the fractures. Most likely, some of the natural fractures slowly grew downward to the monitoring fiber as a result of fluid injections in the stimulated well. This led to bright strain anomalies but did not trigger seismicity. The top of the fractures remained almost constant and were limited by a lithologic boundary/stress barrier. To our knowledge, this is the first time VSP data enabled tracking of the fracture evolution with such high spatial and temporal resolution, which was previously only available for crosswell surveys and at a much smaller scale.

Glubokovskikh, Stanislav↗
DOE OSTI2025

Room‐Temperature Mid‐Infrared Detection Using Metasurface‐Absorber‐Integrated Phononic Crystal Oscillator

Mid-infrared (MIR) detectors find extensive applications in chemical sensing, spectroscopy, communications, biomedical diagnosis, and space exploration. Alternative to semiconductor MIR photodiodes and bolometers, mechanical-resonator-based MIR detectors show advantages in higher sensitivity and lower noise at room temperature, especially toward longer wavelength infrared. Here, uncooled room-temperature MIR detectors based on lithium niobate surface acoustic wave phononic crystal (PnC) resonators integrated with wavelength-and-polarization-selective metasurface absorber arrays are demonstrated. The detection is based on the resonant frequency shift induced by the local temperature change due to MIR absorptions. The PnC resonator is configured in an oscillating mode, enabling active readout and low-frequency noise. The 1-GHz oscillator-based MIR detector shows a relative frequency deviation of 5.24 × 10 −10 Hz −1/2 at an integration time of 50 µs, leading to an incident noise equivalent power of 197 pW Hz −1/2 when input 6-µm MIR light is modulated at 1.8 kHz, and a large dynamic range of 10 7 in incident MIR power. The device architecture is compatible with the scalable manufacturing process and can be readily extended to a broader spectral range by tailoring the absorbing wavelengths of metasurface absorbers.

Xi, Zichen [Virginia Polytechnic Inst. and State U↗
DOE OSTI2025

Crystalline Order Yet Glass-Like Heat Transport Driven by Hidden Local Distortions as the Structural Origin of Ultralow Thermal Conductivity in AgErTe 2

Given their rich chemical diversity and the interplay among the p-, d-, and f-orbitals of chalcogens, transition metals, and lanthanides, respectively, rare-earth transition-metal chalcogenides exhibit a wide variety of structural, magnetic, and transport phenomena. As a result, they form a particularly appealing platform for investigating structure–property relationships, emergent electronic and magnetic behaviors, and thermal transport. Here we investigate AgErTe 2 as a model system to understand phonon-glass behavior in ordered crystalline solids, which establishes the design principles for thermal barrier coatings and next-generation thermoelectrics. The local bonding asymmetry and lattice softness suppress the inherently low lattice thermal conductivity, resembling the characteristics of amorphous materials. This suppression is significantly influenced by local off-centering of Ag atoms, which breaks lattice periodicity while maintaining global crystallinity. The presence of antibonding states just below the Fermi level, arising from Ag 4d and Te 5p orbital interactions, leads to lattice softening and destabilizes ideal tetrahedral coordination, resulting in a pseudo Jahn–Teller distortion. Furthermore, the coexistence of weaker, more polarizable Ag–Te bonds and stronger Er–Te bonds creates a complex vibrational landscape enriched with low-frequency modes and enhanced phonon scattering. A pronounced disparity in interatomic force constants gives rise to highly localized, low-energy optical phonons linked to Ag rattling. These flat vibrational modes exhibit strong coupling with transverse acoustic phonons, resulting in ultrashort phonon lifetimes and mean free paths approaching interatomic distances. These features collectively enhance phonon scattering across a broad range of length and energy scales. This work offers a framework for engineering suppressed thermal conductivity in crystalline systems without the introduction of alloying elements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Species-specific acoustic responses by bats to ultrasonic stimuli used for reducing bat-wind turbine interactions

An unintended consequence of wind energy generation is bat fatalities caused by wind turbine blade strikes. One potential approach to reduce collision risk is to use ultrasound to create an uncomfortable or disorienting airspace around wind turbine blades. Ultrasonic deterrents (UDs) have produced mixed results in experimental field studies at commercial wind energy facilities, with effectiveness varying by species and location. It is possible that some species can alter their normal echolocation characteristics to counter the signal of UDs. Our broad objective was to maximize the effectiveness of a UD by comparing changes in echolocation characteristics during three UD frequency emissions among species, between seasons, and between sex. We hypothesized that UD emissions with frequencies most similar to each species’ echolocation characteristics would be more likely to alter the bats’ echolocation, and bat responses would vary between seasons and sex for each species. We released wild-captured bats into a 60 m × 10 m × 4.4 m (length × width × height) flight cage located in San Marcos, Texas, USA, from July to October 2020 and March to May 2021 and monitored echolocation frequencies with ultrasonic microphones. We conducted trials on Brazilian free-tailed bats ( Tadarida brasiliensis ; n = 54), cave myotis ( Myotis velifer ; n = 44), red bats ( Lasiurus blossevilli , Lasiurus borealis ; n = 41), evening bats ( Nycticeius humeralis ; n = 32), and tricolored bats ( Perimyotis subflavus ; n = 8). We found that species with high-frequency echolocation calls altered their echolocation signatures more commonly during high-frequency UD emissions, whereas low-frequency bats altered their echolocation signatures more commonly during low-frequency UD emissions. Additionally, echolocation responses varied between seasons and sexes for several species. Variations in responses may be dependent on species migratory status, differences in mating behavior and mating season, hormonal differences between sexes and seasons, and/or constraints on echolocation adaptability. Our results offer insights into the variable effectiveness of UDs at reducing bat fatalities at wind turbines and provide information for potential adjustments to UDs for improved success.

17 WIND ENERGY↗
NASA NTRS1972

Radiation resistance of a rectangular panel.

The radiation resistance corresponding to the natural modes of a finite rectangular panel is theoretically determined from the total energy radiated to the farfield. The panel is assumed to be simply supported in an infinite baffle. Asymptotic solutions for the low-frequency region are derived, and curves covering the entire frequency range for various mode shapes and aspect ratios are obtained through numerical integration. When the ratio of the acoustic wavenumber to the panel wavenumber is a constant much less than unity, the radiation resistance for all modes is a minimum if the intranodal area (the area between adjacent node lines) is square, and increases with the aspect ratio of the intranodal area.

Wallace, C. E.↗
NASA NTRS1973

Full-scale experiments with an ejector to reduce jet engine exhaust noise

Experiments with a modified J65 turbojet engine and ejector resulted in noise power reductions as large as 13 decibels in the low-frequency range. High-frequency noise power, which appeared to originate mainly from the mixing processes within the ejector, increased. Peak velocities at the ejector exit were reduced by one-half to two-thirds, although survey rakes showed that mixing was not complete. Acoustical lining inside the ejector would reduce the perceived noise level (in PNdB) by removing much of the high-frequency noise.

Clark, B. J.↗
NASA NTRS1973

Propagation of plane waves in flow through a variable area duct

Duct geometry is an important factor that influences the transmission of sound in a duct. Nonconstant area produces variations in steady flow quantities through the duct, which can cause reflections of acoustic disturbances and the creation of standing wave patterns, and which can attenuate and disperse propagating waves. To study the problem, a second-order-accurate numerical method has been developed. The method of characteristics is used to solve the acoustic equations with the assumption of quasi-one-dimensional flow in the duct. Numerical results are presented over a broad range of frequencies. Low-frequency results are compared with approximate solutions for compact nozzles and high-frequency calculations are compared with results from the short-wave theory. The numerical results are also compared with an analytical solution of the acoustic equations for exponential horn sections with zero mean flow to further establish the validity of the numerical method.

King, L. S.↗
NASA NTRS1975

Acoustic characteristics of a large upper-surface blown configuration with turbofan engines

This paper presents acoustic results from static and simulated low forward velocity tests of a large-scale model of an aircraft configuration with two turbofan engines in the full-scale tunnel at the Langley Research Center. The turbofan engines were integrated into the model and equipped with rectangular nozzles to provide the upper-surface blowing. Results indicate that the upper-surface-blowing noise problem can be characterized, primarily, by the unsymmetrical radiation pattern due mainly to shielding of the high-frequency engine noise and the production of low-frequency noise by jet-surface interaction. The directivity of the low-frequency noise was found to depend on the trailing-edge flap angle when the thrust levels were low. Normalized sound pressure level spectral density data showed good agreement at low Strouhal number with other small- and large-scale model data from tests using simulated wing-flap systems. Forward speed effects were undetectable at the low tunnel speeds used during the tests.

Preisser, J. S.↗
NASA NTRS1976

Correlation of internal surface turbulence with far-field noise of the augmentor wing propulsive-lift concept

A wind tunnel investigation was conducted to determine the nature, strength, and variation with airspeed of the acoustic sources of the augmentor wing propulsive-lift concept. The augmentor wing overall noise is dominated by the high frequency jet mixing noise characteristic of the lobed primary nozzle. The augmentor modifies the intensity and propagation characteristics of the jet sources, especially those that exist inside the augmentor. The interaction of the turbulent flow with the augmentor creates low-frequency, low-intensity surface noise and trailing edge noise. These sources dominate any jet mixing noise that is present at the low frequencies and could become significant if the jet noise was suppressed by treating the augmentor with a lining tuned to the jet noise source location. The far-field noise of the untreated augmentor is unaffected by airspeed; however, this may not be the case when the jet noise is suppressed, because the trailing edge surface pressure and correlations with far-field noise do show a reduction with forward speed.

Falarski, M. D.↗