Search NASA⌕ Search

SEARCH · Search NASA

Results for “low-thrust orbit transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Propellant management for low thrust chemical propulsion systems

Low-thrust chemical propulsion systems (LTPS) will be required for orbital transfer of large space systems (LSS). The work reported in this paper was conducted to determine the propellant requirements, preferred propellant management technique, and propulsion system sizes for the LTPS. Propellants were liquid oxygen (LO2) combined with liquid hydrogen (LH2), liquid methane or kerosene. Thrust levels of 100, 500, and 1000 lbf were combined with 1, 4, and 8 perigee burns for transfer from low earth orbit to geosynchronous earth orbit. This matrix of systems was evaluated with a multilayer insulation (MLI) or a spray-on-foam insulation. Vehicle sizing results indicate that a toroidal tank configuration is needed for the LO2/LH2 system. Multiple perigee burns and MLI allow far superior LSS payload capability. Propellant settling, combined with a single screen device, was found to be the lightest and least complex propellant management technique.

Hamlyn, K. M.↗
NASA NTRS1985

An analysis of low-thrust, resistojet reboost for the Space Station

This paper presents results of an analysis of low-thrust orbit maintenance of the Space Station. Propellant requirements and transfer times are given for reboost of the station through various altitude increments. The reboost can readily be accomplished with thrust levels that subject the station to an acceleration of less than the desired upper limit of 10 to the -5th g's. The variation in time and the probabilistic aspect of the predicted upper-atmospheric density as well as the variation in time of sun-pointing drag areas were taken into account. Estimates of the propellant requirements at different times during an 11-year solar cycle are given. It is shown that the amount of CO2 available from the station life-support system is sufficient, over most of the solar cycle, to provide the propellant for a resistojet orbit-maintenance system.

Penko, P. F.↗
NASA NTRS1982

Structures-propulsion interactions and requirements

The effects of low-thrust primary propulsion system characteristics on the mass, area, and orbit transfer characteristics of large space systems (LSS) were determined. Three general structural classes of LSS were considered, each with a broad range of diameters and nonstructural surface densities. While transferring the deployed structure from LEO and to GEO, an acceleration range of 0.02 to 0.1 g's was found to maximize deliverable payload based on structural mass impact. After propulsion system parametric analyses considering four propellant combinations produced values for available payload mass, length and volume, a thrust level range which maximizes deliverable LSS diameter was determined corresponding to a structure and propulsion vehicle. The engine start and/or shutdown thrust transients on the last orbit transfer (apogee) burn can impose transient loads which would be greater than the steady-state loads at the burnout acceleration. The effect of the engine thrust transients on the LSS was determined from the dynamic models upon which various engine ramps were imposed.

Coyner, J. V.↗
NASA NTRS1982

The Centaur family

The Centaur upper stage has been used with Atlas and Titan boosters for a total of 66 launches, and is now being considered for future use with the Space Shuttle. Centaur's high-energy oxygen-hydrogen propellant combination provides the maximum performance capability for launching geosynchronous and earth-escape missions with both boosters. Shuttle/Centaur performance, combined with the demonstrated low-thrust operating capability of the Centaur engines, will allow gentle transfer of large communications spacecraft into geostationary orbit, thus significantly increasing the economies of communication satellites. This paper presents Centaur configurations, payload capabilities, and payload envelopes for future applications.

Rector, W. F., III↗
NASA NTRS1978

Ion drive performance and trajectories

The use of Solar Electric Propulsion (SEP) for the Solar Probe Mission is addressed. The dependence of the payload mass on the site of the SEP and the flight time are described on the basis of preliminary data. The range of hardware expected to be available in the 1980's is summarized. There are several classes of optimal low-thrust trajectories for the Solar Probe Mission. These are trajectory types A, B, C corresponding to one, two, or three orbital revolutions, respectively. Plots of transfer trajectories corresponding to type-A, type-A with a Venus Swingby, type-B, and type-C with ab Icarus Rendezvous are shown. A summary of the SEP performance is given.

Yen, C. L.↗
NASA NTRS1982

Propulsion system options for low-acceleration orbit transfer

The present inventory of developed bipropellant engines suitable for the orbit transfer of large space structures is based on the use of storable propellants (nitrogen tetroxide/monomethyl hydrazine). A range of engine sizes from 22N (5 lbF) to over 26,690N (6000 lbF) is available. These engines are capable of delivering specific impulse values from 2795 to 3089 N-s/kg (285 to 315 lbF-sec/lbm). A comparison is made between the attainable specific impulse of these demonstrated engines and future low-thrust engine designs which can utilize LOX/RP-1, LOX-methane, and LOX/hydrogen propellants. The requirements for cooling these small engines for multi-hour burns as well as the merits of operating at nonoptimum performance mixture ratios to improve cooling margins and reduce tank volumes are addressed in this paper.

Schoenman, L.↗
NASA NTRS1984

Evaluation of propellant tank insulation concepts for low-thrust chemical propulsion systems

An analytical evaluation of cryogenic propellant tank insulations for liquid oxygen/liquid hydrogen low-thrust 2224N (500 lbf) propulsion systems (LTPS) was conducted. The insulation studied consisted of combinations of N2-purged foam and multilayer insulation (MLI) as well as He-purged MLI-only. Heat leak and payload performance predictions were made for three Shuttle-launched LTPS designed for Shuttle bay packaged payload densities of 56 kg/cu m, 40 kg/cu m and 24 kg/cu m. Foam/MLI insulations were found to increase LTPS payload delivery capability when compared with He-purged MLI-only. An additional benefit of foam/MLI was reduced operational complexity because Orbiter cargo bay N2 purge gas could be used for MLI purging. Maximum payload mass benefit occurred when an enhanced convection, rather than natural convection, heat transfer was specified for the insulation purge enclosure. The enhanced convection environment allowed minimum insulation thickness to be used for the foam/MLI interface temperature selected to correspond to the moisture dew point in the N2 purge gas. Experimental verification of foam/MLI benefits was recommended. A conservative program cost estimate for testing a MLI-foam insulated tank was 2.1 million dollars. It was noted this cost could be reduced significantly without increasing program risk.

Kramer, T.↗
NASA NTRS1984

Evaluation of propellent tank insulation concepts for low-thrust chemical propulsion systems: Executive summary

Cryogenic propellant tank insulations or liquid oxygen/liquid hydrogen low-thrust 2224N (500 lbf) propulsion systems (LTPS) were assessed. The insulation studied consisted of combinations of N2-purged foam and multilayer insulation (MLI) as well as He-purged MLI-only. Heat leak and payload performance predictions were made for three shuttle-launched LTPS designed for shuttle bay packaged payload densities of 56 kg cu/m (3.5 lbm/cu ft), 40 kg/cu m (2.5 lbm/cu ft) and 24 kg/cu m (1.5 lbm/cu ft). Foam/MLI insulations were found to increase LTPS payload delivery capability when compared with He-purged MLI-only. An additional benefit of foam/MLI was reduced operational complexity because orbiter cargo bay N2 purge gas could be used for MLI purging. Maximum payload mass benefit occurred when an enhanced convection, rather than natural convection, heat transfer was specified for the insulation purge enclosure. The enhanced convection environment allowed minimum insulation thickness to be used for the foam/MLI interface temperature selected to correspond to the moisture dew point in the N2 purge gas. Experimental verification of foam/MLI benefits was recommended. A conservative program cost estimate for testing a MLI-foam insulated tank was 2.1 million dollars. This cost could be reduced significantly without increasing program risk.

Kramer, T.↗
NASA NTRS1974

A users manual for a computer program which calculates time optical geocentric transfers using solar or nuclear electric and high thrust propulsion

This manual is a guide for using a computer program which calculates time optimal trajectories for high-and low-thrust geocentric transfers. Either SEP or NEP may be assumed and a one or two impulse, fixed total delta V, initial high thrust phase may be included. Also a single impulse of specified delta V may be included after the low thrust state. The low thrust phase utilizes equinoctial orbital elements to avoid the classical singularities and Kryloff-Boguliuboff averaging to help insure more rapid computation time. The program is written in FORTRAN 4 in double precision for use on an IBM 360 computer. The manual includes a description of the problem treated, input/output information, examples of runs, and source code listings.

Sackett, L. L.↗
NASA NTRS1980

Low-thrust vehicles concept studies

Low thrust chemical (hydrogen-oxygen) propulsion systems configured specifically for low acceleration orbit transfer of large space systems were studied in order to provide the required additional data to better compare new, low thrust chemical propulsion systems with other propulsion approaches such as advanced electric systems. Study results indicate that it is cost-effective and least risk to combine the low thrust OTV and stowed spacecraft in a single 65 K shuttle. Mission analysis indicates that there are 25 such missions, starting in 1987. Multiple shuttles (LSS in one, OTV in another) result in a 20% increase in LSS (SBR) diameter over single shuttle launches. Synthesis and optimization of the LSS characteristics and OTV capability resulted in determination of the optimum thrust-to-weight and thrust level. For the space based radar with radial truss arms (center thrust application), the optimum thrust-to-weight (maximum) is 0.1, giving a thrust of 2000 lb. For the annular truss (edge-on thrust application) the structure is not as sensitive, and thrust of 1000 lb appears optimum. For the geoplatform, optimum T/W is .15 (3000 lb thrust). The effects of LSS structure material, weight distribution, and unit area density were evaluated, as were the OTV engine thrust transient and number of burns.

Ketchum, W. J.↗
NASA NTRS1980

Low-thrust chemical rocket engine study

Parametric data and preliminary designs on liquid rocket engines for low thrust cargo orbit-transfer-vehicles are described and those items where technology is required to enhance the designs are identified. The results of film cooling studies to establish the upper chamber pressure limit are given. The study showed that regen cooling with RP-1 was not feasible over the entire thrust and chamber pressure ranges. The thermal data showed that the RP-1 bulk temperature exceeded the study coking temperature limit of 1010 R. Based upon the results presented, O2/H2 and O2/CH4 regen engine systems and O2/H2 film cooled engines were selected for further study in the system analysis. Six engine design concepts are examined.

Mellish, J. A.↗
NASA NTRS1981

Low-thrust chemical rocket engine study

An analytical study evaluating thrust chamber cooling engine cycles and preliminary engine design for low thrust chemical rocket engines for orbit transfer vehicles is described. Oxygen/hydrogen, oxygen/methane, and oxygen/RP-1 engines with thrust levels from 444.8 N to 13345 N, and chamber pressures from 13.8 N/sq cm to 689.5 N/sq cm were evaluated. The physical and thermodynamic properties of the propellant theoretical performance data, and transport properties are documented. The thrust chamber cooling limits for regenerative/radiation and film/radiation cooling are defined and parametric heat transfer data presented. A conceptual evaluation of a number of engine cycles was performed and a 2224.1 N oxygen/hydrogen engine cycle configuration and a 2224.1 N oxygen/methane configuration chosen for preliminary engine design. Updated parametric engine data, engine design drawings, and an assessment of technology required are presented.

Shoji, J. M.↗
NASA NTRS1981

Low-thrust chemical propulsion system pump technology

Candidate pump and driver systems for low thrust cargo orbit transfer vehicle engines which deliver large space structures to geosynchronous equatorial orbit and beyond are evaluated. The pumps operate to 68 atmospheres (1000 psi) discharge pressure and flowrates suited to cryogenic engines using either LOX/methane or LOX/hydrogen propellants in thrust ranges from 445 to 8900 N (100 to 2000 lb F). Analysis of the various pumps and drivers indicate that the low specific speed requirement will make high fluid efficiencies difficult to achieve. As such, multiple stages are required. In addition, all pumps require inducer stages. The most attractive main pumps are the multistage centrifugal pumps.

Sabiers, R. L.↗