Search NASA⌕ Search

SEARCH · Search NASA

Results for “macroscale yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

31 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Study of the interplay between lower-order and higher-order energetic strain-gradient effects in polycrystal plasticity

in this report strain-gradient (SG) plasticity refers to a class of non-local theories in which gradients of plastic slip determine the storage of geometrically necessary dislocations, introducing a length-scale dependence in the mechanical behavior of crystalline materials, which is otherwise lacking in local theories. In this work, we incorporate lower-order (LO) and higher-order energetic (HOE) strain-gradient effects into a crystal plasticity fast Fourier transform (FFT)-based formulation to investigate the interplay of the length scale that each strain-gradient term introduces at the microscale, and the mechanical properties that result at the macroscale. For an applicable range of length scales, we consider two systems: a 1-D two-phase face centered cubic (FCC) laminate and a 3-D FCC polycrystal, and two uniaxial deformation modes: monotonic tension and cyclic tension–compression. We show that increases in the individual LO and HOE length scales increase the hardening rate and strength of the material, respectively. When combined, the strong LO hardening is less pronounced than the effect alone due to the lowering of the gradients due to the HOE microstress. We demonstrate that the LO and HOE hardening manifest as “isotropic” (yield surface expansion) and “kinematic” (yield surface shift) effects, respectively, consistent with their theoretical origins. We show that in cyclic loading, the Bauschinger effect emerges in both local and non-local calculations and link its origins and severity to the behavior in the strain field, slip-system rates, and the HOE microforce.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Making Precise Resonators for Mesoscale Vibratory Gyroscopes

An alternative approach to the design and fabrication of vibratory gyroscopes is founded on the use of fabrication techniques that yield best results in the mesoscopic size range, which is characterized by overall device dimensions of the order of a centimeter. This approach stands in contradistinction to prior approaches in (1) the macroscopic size range (the size range of conventional design and fabrication, characterized by overall device dimensions of many centimeters) and (2) the microscopic size range [the size range of microelectromechanical systems (MEMS), characterized by overall device dimensions of the order of a millimeter or less]. The mesoscale approach offers some of the advantage of the MEMS approach (sizes and power demands smaller than those of the macroscale approach) and some of the advantage of the macroscale approach (the possibility of achieving relative dimensional precision greater than that of the MEMS approach). Relative dimensional precision is a major issue in the operation of a vibratory gyroscope. The heart of a vibratory gyroscope is a mechanical resonator that is required to have a specified symmetry in a plane orthogonal to the axis about which rotation is to be measured. If the resonator could be perfectly symmetrical, then in the absence of rotation, a free vibration of the resonator could remain fixed along any orientation relative to its housing; that is, the gyroscope could exhibit zero drift. In practice, manufacturing imprecision gives rise to some asymmetry in mass, flexural stiffness or dissipation, resulting in a slight drift or beating motion of an initial vibration pattern that cannot be distinguished from rotation. In the mesoscale approach, one exploits the following concepts: For a given amount of dimensional error generated in manufacturing, the asymmetry and hence the rate-of-rotation drift of the gyroscope can be reduced by increasing the scale. The decrease in asymmetry also reduces coupling of vibrations to the external environment. Mechanical thermal noise and electronic measurement noise and drift can also be reduced by increasing the size of the resonator and its associated sensors.

Yang, Eui-Hyeok↗
DOE OSTI2024

Role of Selenium in CdZnTeSe as a Defect Engineering Agent

Cadmium zinc telluride (CdZnTe) with 10 atomic % Zn has been the material of choice for room-temperature semiconductor compact X- and gamma-ray detector applications for over three decades. Despite its commercial success as the most desirable room-temperature semiconductor radiation detection material, CdZnTe (CZT) suffers from a lack of compositional homogeneity on both the micro- and macroscales and the presence of high concentrations of performance-limiting defects such as subgrain boundary networks (dislocation walls) and secondary phases (Te-rich inclusions). Random distributions of these defects in the CZT matrix result in the spatial inhomogeneity of the material’s charge-transport properties. The recently discovered quaternary Cd x Zn 1-x Te 1-y Se y (CZTS) has experienced remarkable advances in its material properties, with highly reduced defects and higher compositional homogeneity. This book chapter focuses on the presence of performance-limiting defects in CZT that have thus far hindered the yield and cost of high-quality detectors and restricted their widespread deployment for a variety of potential applications, particularly for their use as large-volume gamma detectors, where the demands on material perfection are significantly greater. This chapter also provides an overview of the recent developments in the quaternary material CZTS, particularly the effects of selenium (Se) in the CZTS matrix on the defect engineering of the quaternary alloy material and the advancement of CZTS as a potential next-generation detector operable at room temperature.

Roy, Utpal N.↗
DOE OSTI2024

Macroscopic modeling of gas permeability in hierarchical micro/nanoporous media: A unified characterization of rarefaction using Klinkenberg theory and equivalent diameter

Estimating gas transport through a hierarchical micro/nanoporous system is challenging due to non-equilibrium gas dynamics. The primary difficulty lies in determining the rarefaction level, because identifying a representative flow dimension in a complex porous system with multiple pore scales is not straightforward. Our study performed a pore-level analysis for gas permeability in dual-scale porous media with varying porosity, throat size, and secondary pore size under different rarefaction conditions. We found that secondary porosity negatively affects permeability due to increased friction forces, with this influence growing as the secondary pore size and porosity increase until the secondary pore becomes comparable to the throat. However, rarefaction reduces the effects of secondary pores due to boundary slip. Traditional Knudsen number (Kn) calculations based on Darcy-defined height failed to accurately describe the rarefaction effects on gas permeability. Instead, we introduced an equivalent diameter to calculate the Kn, which provided an accurate normalization of apparent gas permeability independent of pore geometry. Furthermore, the extended Kozeny–Carman–Klinkenberg model developed in our previous study successfully yielded a macroscopic model for apparent gas permeability in hierarchical micro/nanoporous systems as a function of the traditional Darcy height and porosity.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

A Multi-modal Approach to Understanding Degradation of Organic Photovoltaic Materials

State-of-the-art organic photovoltaic (OPV) materials are composed of complex, chemically diverse polymeric and molecular structures that form highly intricate solid-state interactions, collectively yielding exceptional tunability in performance and aesthetics. These properties are especially attractive for semitransparent power-generating windows or shades in living environments, greenhouses, or other architectural integrations. However, before such a future is realized, a broader and deeper understanding of property stability must be acquired. Stability during operating and environmental conditions is critical, namely, material color steadfastness, optoelectronic performance retention, morphological rigidity, and chemical robustness. To date, no single investigation encompasses all four distinct, yet interconnected, metrics. Here, we present a multimodal strategy that captures a dynamic and interconnected evolution of each property during the course of an accelerated photobleaching experiment. We demonstrate this approach across relevant length scales (from molecular to visual macroscale) using X-ray photoelectron spectroscopy, grazing-incidence X-ray scattering, microwave conductivity, and time-dependent photobleaching spectroscopies for two high-performance semitransparent OPV blends—PDPP4T:PC 60 BM and PDPP4T:IEICO-4F, with comparisons to the stabilities of the individual components. We present direct evidence that specific molecular acceptor (fullerene vs nonfullerene) designs and the resulting donor–acceptor interactions lead to distinctly different mechanistic routes that ultimately arrive at what is termed “OPV degradation.” We directly observe a chemical oxidation of the cyano endcaps of the IEICO-4F that coincides with a morphological change and large loss in photoconductivity while the fullerene acceptor-containing blend demonstrates a significantly greater fraction of oxygen uptake but retains 55% of the photoconductivity. Finally, this experimental roadmap provides meaningful guidance for future high-throughput, multimodal studies, benchmarking the sensitivity of the different analytical techniques for assessing stability in printable active layers, independent of complete device architectures.

14 SOLAR ENERGY↗
DOE OSTI2025

A Solvatochromic Near Infrared Fluorophore Sensitive to the Full Amyloid Beta Aggregation Pathway

Alzheimer's disease has long been associated with the aggregation of amyloid beta peptides (Aβ42) into macroscale plaques, although specific neurodegenerative agents have not been definitively identified. Much evidence has pointed to the soluble nanoscale oligomers that form early in the Aβ42 aggregation pathway, but there is little understanding of these structures, their mechanisms of formation, or how they grow into plaques. Here, we show that a solvatochromic fluorophore with near-infrared (NIR) emission can track synthetic Aβ42 aggregation through environment-sensitive spectral shifts from the earliest time points through plaque formation. This azide-functionalized phosphine oxide azetidine rhodol (Phazr-N3) shows large polarity-dependent changes in fluorescence emission, with maxima shifting from 630 nm in toluene to 703 nm in aqueous buffer, and a maximum quantum yield of 62%. Upon induction of Aβ42 aggregation, we observe immediate solvatochromic changes in Phazr-N3 fluorescence, with multiple apparent phases over 12 h, and which culminate before the onset of any major fluorescence changes of conformation-specific aggregation fluorophore thioflavin T. Solution anisotropy measurements show a low micromolar affinity of Phazr-N3 for disordered, free Aβ42 in solution, and real-time measurements are consistent with rapid liquid-liquid phase separation and slow dehydration of the growing aggregate. Spectral imaging of synthetic plaques stained in the presence of live cells and lipid-binding protein albumin shows over 4000-fold Phazr-N3 fluorescence intensity above background under no-wash conditions, and over 100-fold intensity above coplated microglial cells or a large excess of albumin. This use of a solvatochromic probe with structure-independent binding to free Aβ42 offers real-time, minimally invasive insight into the full Aβ42 aggregation pathway.

Wang, Zeming↗
DOE OSTI2023

Macroscale property assessment and indentation characteristics of thick section friction stir welded AA 5083

The spatial gradients in microstructure have been proven to be effective in optimizing the performance of components, and several techniques have been developed to achieve this microstructure. Nevertheless, the local microstructural modification methods inevitably result in the formation of gradient microstructure leading to a variation in the property. Herein this work systematically investigates the effect of gradient microstructure formed during thick section friction stir weld Al5083 alloy on its mechanical properties. A novel macro-indentation technique, profilometer-based indentation plastometry (PIP), is utilized to capture the variation in the mechanical properties in the feedstock (rolled plate) and weld region. The feedstock exhibited a gradient microstructure owing to different stress states during rolling. Additionally, the stirring of the tool resulted in a complex material flow pattern producing a microstructure gradient in the weld region. The aspect ratio of the grains was identified as the primary factor causing variation in indentation response in the feedstock. In contrast, variation in the grain size in the weld region resulted in property variation. Overall, the stir zone has a lower yield strength (158±4MPa) than the base material (173±3MPa). In addition, microstructure heterogeneity in the stir zone resulted in lower elongation than the base material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manufacturing Dissolvable Alloy Components using ShAPE: A Study on Solid Phase Processing of Mg-W Composites and WJ11 Alloys

Dissolvable alloys and composites are an emerging class of materials that demonstrate tailored sorptivity in corrosive environments. This work explored the viability of solid phase processing (SPP) techniques, namely the shear assisted processing and extrusion (ShAPETM) method, to manufacture dissolvable magnesium composites and alloys components such as rods and tubes. The study also determined the effects of material composition and manufacturing process conditions on material microstructures developed during SPP and the resulting performance of the components. Explicit properties of interest included ultimate tensile strength, ultimate compressive strength, and yield strength. The application fields of interest for dissolvable alloys were identified as oil-and-gas operations and biomedical implants. Accordingly, PNNL collaborated with industrial and academia partners, Fortek Industries, Houston and University of Pittsburgh, during the course of this project for material and ShAPE process development. PNNL determined the viability of the using ShAPE to process the custom-designed materials provided by the project partners. This was done by identifying process parameters such as tool rotation rate, tool plunge rate, and process cooling optimal for manufacturing components with consolidated microstructures. Subsequently, PNNL also performed microstructural characterization on unprocessed and processed samples and mechanical property testing. One of the major findings from this work is that ShAPE was able to manufacture dissolvable magnesium composite and alloy rods and tubes with consolidated homogeneous microstructures and minimal macroscale defects on component surfaces. It was observed that samples processed via ShAPE demonstrated an average grain size < 2 - 5 µm, which was markedly lower than that of the precursors with 8 – 13 µm grains. Results showed that the ShAPE synthesized dissolvable magnesium composite and alloy strength was on par with or better than those components that were manufactured using traditional manufacturing processes such as forging and extrusion. It is noteworthy that the ShAPE samples were made with considerably lower number of process steps.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Effects of Subscale Size and Shape on Global Energy Dissipation in a Multiscale Model of a Fiber-Reinforced Composite Exhibiting Post-Peak Strain Softening Using Abaqus and FEAMAC

A mesh objective crack band model is implemented in the generalized method of cells (GMC) micromechanics model to predict failure of a composite repeating unit cell (RUC). The micromechanics calculations are achieved using the MAC/GMC core engine within the ImMAC suite of micromechanics codes, developed at the NASA Glenn Research Center. The microscale RUC is linked to a macroscale Abaqus/Standard finite element model using the FEAMAC multiscale framework (included in the ImMAC suite). The effects of the relationship between the characteristic length of the finite element and the size of the microscale RUC on the total energy dissipation of the multiscale model are investigated. A simple 2-D composite square subjected to uniaxial tension is used to demonstrate the effects of scaling the dimensions of the RUC such that the length of the sides of the RUC are equal to the characteristic length of the finite element. These results are compared to simulations where the size of the RUC is fixed, independent of the element size. Simulations are carried out for a variety of mesh densities and element shapes, including square and triangular. Results indicate that a consistent size and shape must be used to yield preserve energy dissipation across the scales.

Pineda, Evan, J.↗
DOE OSTI2025

Elucidating texture and grain morphology contributions to the micromechanical response of additively manufactured Inconel 625

Microstructural variation of additively manufactured (AM) metal components in comparison to wrought counterparts makes certification for critical applications a challenge. Microscale simulations leveraging modern computational tools may be used to supplement testing of AM microstructures, thus accelerating certification by reducing the number of experiments needed. However, as micromechanical response is closely tied to critical properties like fatigue-life and fracture, utilization of these simulations with macroscale experimental data alone is insufficient. One means to attain microscale experimental data is in situ diffraction data collected from synchrotron X-ray sources. In this work, such data were collected during in situ compression of AM Inconel 625 superalloy. Interpretation of experimental results was assisted by massive (8M element) complementary micromechanical simulations performed on sets of virtual microstructures generated using cellular automata. Together, micromechanical data from diffraction experiments and simulations were used to probe the effects of textured “track” microstructures generated during laser powder bed fusion and directional strength-to-stiffness on micromechanical response. Though fiber-averaged directional strength-to-stiffness ratios were expected to dominate given the high elastic anisotropy of the material, the combination of small variations in texture and specific grain configurations unique to AM microstructures lead to significant variability in micromechanical response after yield. The findings emphasize the importance of high-fidelity microstructural representation that captures key texture components and AM-specific morphology for property prediction of AM metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An extended three-field principle to scale-bridge the granular micromechanics of polymer-bonded particulate materials

Observed phenomena of damage, viscoelasticity, and viscoplasticity in polymer-bonded particulate materials (PBPM), like polymer-bonded explosive (PBX), are accommodated in a scale-bridging constitutive model based on granular micromechanics. An extended three-field variational principle with min - max optimization problem is introduced to homogenize the bonded aggregates’ grain-scale contact mechanics. Similarly to prior applications of a three-field principle, volume constraints are invoked to embed microscale-to-macroscale correspondences for kinematic and static volumetric measures, like mean strain and its energy-conjugate stress invariant. Unlike prior applications, our three-field principle realizes a strain-driven model for effective constitutive behavior due to bonded intergranular contact. In conclusion, the resultant micro-sphere integration-based homogenization is demonstrated in comparison to existing publicly-available measurements to capture the extreme tension/compression constitutive asymmetry exhibited by PBPMs (specifically PBX-9501) during material softening.

42 ENGINEERING↗
DOE OSTI2023

Prediction and Validation of Flow Properties in Porous Lattice Structures

High-porosity metal foams have been extensively studied as an attractive candidate for efficient and compact heat exchanger design. With the advancements in additive manufacturing, such foams can be manufactured with controlled topology to yield highly tailorable mechanical and transport properties. In this study, a lattice Boltzmann method (LBM)-based pore-scale model is implemented to simulate the fluid flow in additively manufactured (AM) metal foams with unit cell topologies of Cube, Face Diagonal (FD)-Cube, Tetrakaidecahedron (TKD), and Octet lattices. The pressure gradient versus average velocity profiles predicted by the LBM model were validated against in-house measurements on the AM lattice samples with the same unit cell topologies. Based on the simulation results, a novel hybrid model is proposed to accurately predict the volume averaged flow properties (permeability and inertial coefficients) of the four structures. Specifically, the linear LBM (neglecting inertial forces) is first implemented to obtain the intrinsic permeability, and then the standard LBM is applied to obtain the inertial coefficient. Convenient correlations for those flow properties as a function of porosity and fiber diameter are constructed. The effects of the AM print qualities on the flow properties are also discussed. The advantages of the hybrid model compared to the polynomial fitting approach for determining flow properties are discussed and compared quantitatively. The hybrid model and presented results are valuable for flow and thermal transport evaluation when designing new metal foams for specific applications and with different materials and topologies. Finally, the presented correlations based on pore-scale simulations can also be conveniently used in volume-averaged models to predict the macroscale flow behavior in such complex structures.

42 ENGINEERING↗