Search NASA⌕ Search

SEARCH · Search NASA

Results for “magnetron sputtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Lithium nitride coatings deposited by magnetron sputtering on sulfide electrolytes for solid-state batteries

Lithium nitrides have been considered as promising candidates for interfacial layers in solid-state lithium batteries (SSBs). Previously reported lithium nitride (Li 3 N) coatings were mostly prepared by the reaction between lithium metal and nitrogen gas, which makes it challenging for their thickness control and integration in SSBs. In this study, we prepare Li 3 N via magnetron sputtering for the first time, and apply the resulting coating directly on sulfide solid-state electrolyte. A much smaller impedance increase associated with improved cycling performance is observed in lithium metal symmetric cell. These results demonstrate the feasibility of depositing Li 3 N via magnetron sputtering and its application in SSBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Characterizing the composition, structure, and mechanical properties of magnetron sputtering physical vapor deposition TiN and TiSiN coatings

Ti(Si)N coatings were deposited on Si wafers via magnetron sputtering physical vapor deposition technique. Scanning electron microscopy and atomic force microscopy were used to study the morphologies, grain size, and thicknesses of the different films. X-ray diffraction confirmed the formation of the titanium nitride cubic phase. X-ray photoelectron spectroscopy (XPS) was used to study the silicon and oxygen levels in the films, and high resolution XPS was used to determine the surface oxide to nitride ratios as well as the silicon–nitrogen environment. The hardness of these films was then determined with nanoindentation. It was shown that grain size and film density could be controlled by the Si level and the ion bombardment to eliminate the oxygen level in the nitride coatings, which led to the harder films. It was suggested that due to the miscibility of Si, a ternary TiSiN solid solution was formed. Stronger (200) orientation of the TiN B1-NaCl crystals was associated with increased hardness of the coatings. In conclusion, this crystalline structure was preserved after incorporating Si.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Properties of Nb3Sn films fabricated by magnetron sputtering from a single target

Superconducting Nb3Sn films were fabricated on sapphire and fine grain Nb substrates by magnetron sputtering from a single stoichiometric Nb3Sn target. The structural, morphological and superconducting properties of the films annealed for 24 h at temperatures of 800-1000 {\deg}C were investigated. The effect of the annealing time at 1000 {\deg}C was examined for 1, 12, and 24 h. The film properties were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, energy dispersive X-ray spectroscopy, and Raman spectroscopy. The DC superconducting properties of the films were characterized by a four-point probe measurement down to cryogenic temperatures. The RF surface resistance of films was measured over a temperature range of 6-23 K using a 7.4 GHz sapphire-loaded Nb cavity. As-deposited Nb3Sn films on sapphire had a superconducting critical temperature of 17.21 K, which improved to 17.83 K when the film was annealed at 800 {\deg}C for 24 h. For the films annealed at 1000 {\deg}C, the surface Sn content was reduced to ~11.3 % for an annealing time of 12 h and to ~4.1 % for an annealing time of 24 h. The Raman spectra of the films confirmed the microstructural evolution after annealing. The RF superconducting critical temperature of the as-deposited Nb3Sn films on Nb was 16.02 K, which increased to 17.44 K when the film was annealed at 800 {\deg}C for 24 h.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Boron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering

Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B 4 C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. Here, we systematically study properties of B 4 C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200MPa.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing layered structure of Inconel 625 coatings prepared by magnetron sputtering

Coating/substrate interface and oxide layers present in Inconel 625 film may cause significant impacts on its corrosion behavior. However, layered structure of Inconel 625 coatings remains poorly understood due to its requirement of high spatial resolution. Here we have applied X-ray reflectometry (XRR) to probe the layered structure of magnetron-sputtered Inconel 625 film with atomic spatial resolution. Our results indicate that there exists a 2 nm thick Cr-rich Inconel sublayer underneath the principal film. On top of the principal film, it is found a 2 nm thick oxide layer mainly consisting of NiO. In addition, we detected ~2 Å contamination layer on the sapphire substrate, although argon ion sputter cleaning had been applied to the substrate prior to deposition. By comparing the coatings with different deposition time, we observed that the thickness of principal Inconel 625 layer grows linearly with deposition time, with all other layers remaining constant. Our findings provide insight into the layered structures of Inconel 625 coatings with atomic-scale spatial resolution, and provide directions for future efforts that aim to improve the corrosion resistance of Inconel 625 coatings.

14 SOLAR ENERGY↗
DOE OSTI2024

Commissioning of a modulated pulse-power magnetron sputtering system for depositing niobium thin films

A modulated pulse-power magnetron sputtering system (MPPMS) was commissioned and used to deposit niobium on copper. MPPMS utilizes a modulated pulse train with high peak-to-average energy ratios, thereby increasing the energy density leading to the production of the energetic ions. The MPPMS modulator was designed and constructed based on large voltage/current IGBT modules, which can be externally modulated, produce bi-polar waveforms, and are readily available. A high voltage power supply provides moderate current to the IGBT module to create the precise pulse structure. The MPPMS system was used to deposit ~1 mm thick, niobium film on a copper substrate held at ~77 K to minimize Nb atom surface diffusion and maximize intrinsic film energy. Finally, the Nb film had an average grain size of ~8 nm.

42 ENGINEERING↗
DOE OSTI2024

Impact of high-power impulse magnetron sputtering pulse width on the nucleation, crystallization, microstructure, and ferroelectric properties of hafnium oxide thin films

The impact of the high-power impulse magnetron sputtering (HiPIMS) pulse width on the crystallization, microstructure, and ferroelectric properties of undoped HfO 2 films is investigated. HfO 2 films were sputtered from a hafnium metal target in an Ar/O 2 atmosphere, varying the instantaneous power density by changing the HiPIMS pulse width with fixed time-averaged power and pulse frequency. The pulse width is shown to affect the ion-to-neutral ratio in the depositing species with the shortest pulse durations leading to the highest ion fraction. In situ x-ray diffraction measurements during crystallization demonstrate that the HiPIMS pulse width impacts nucleation and phase formation, with an intermediate pulse width of 110 μ s stabilizing the ferroelectric phase over the widest temperature range. Although the pulse width impacts the grain size with the lowest pulse width resulting in the largest grain size, the grain size does not strongly correlate with the phase content or ferroelectric behavior in these films. In conclusion, these results suggest that precise control over the energetics of the depositing species may be beneficial for forming the ferroelectric phase in this material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of 1D and 2D particle-in-cell simulations for DC magnetron sputtering discharges

One-dimensional and two-dimensional particle-in-cell (PIC)/Monte Carlo collision simulations are performed for a balanced direct current magnetron sputtering (DCMS) discharge. The plasma parameters obtained by both simulations above the target racetrack share similar features and magnitudes under similar discharge intensities, i.e., similar local discharge current densities. The commonly observed high-energy tail of electron energy distribution in DCMS discharges is reproduced in both simulations. Additionally, the accuracy and applicability of using onedimensional simulations to qualitatively investigate the characteristics of balanced DCMS discharge are confirmed. In terms of capturing the key physical mechanisms in DCMS, one-dimensional PIC simulation is an efficient method, which could largely alleviate the computational expense and preserve the physical fidelity of modeling results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Superlattice-Structured Films by Magnetron Sputtering as New Era Electrodes for Advanced Lithium-ion Batteries

Sustaining sound structures in Si-based anodes is extremely challenging because of the high volumetric expansion that occurs upon cycling. To maintain high capacities over cycles, new designs rely on engineering-specific hierarchical geometries and/or optimized composite compositions such that at least one of the multiple elements serves as buffer and/or electron conductive pathways in the electrodes. In this paper, we report an innovative design in which alternating layers of periodic atomic structures involving multiple elements form a new anode material for lithium-ion batteries. In this work, a superlattice-structured amorphous film made using Si, Mo, and Cu is fabricated by a simple and scalable magnetron sputtering process for the first time. This continuous and repetitive superlattice formation along the film thickness provides a homogeneous stress-strain distribution. The Mo-Cu layer in the superlattice acts as an inactive-conductive layer and as a backbone to handle the volume expansion of active Si upon cycling. This nano-functional superlattice approach enables harnessing the high energy density of Si while maintaining its structural stability. As a result, the electrode exhibits high specific capacity and capacity retention even at high cycling rates. The possible use of the film in a full cell is also evaluated by cycling it vs. the LiMn 1.5 Ni 0.5 O 4 cathode. The full cell maintains a stable capacity of about 900 mAh g anode -1 over 150 cycles, at ~600 mA g -1 rate. The remarkable performance of this nano-functional superlattice film is found to be promising as anodes for applications that require high energy, long calendar life, and excellent abuse tolerance such as electric vehicle batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

High-Power Impulse Magnetron Sputter Deposition of Ultrathick Amorphous Carbon

Diamond-like carbon (DLC) is a material of interest for inertial confinement fusion (ICF) ablators. However, the deposition of ultrathick DLC coatings, as required for ICF ablator fabrication, remains a challenge. Here, in this study, we use high-power impulse magnetron sputtering to deposit DLC and demonstrate a set of process parameters leading to high-purity, amorphous DLC coatings with a low compressive residual stress of <400 MPa. Coatings with thicknesses of up to 80 μm are demonstrated.

amorphous carbon↗
DOE OSTI2021

Oblique angle deposition of boron carbide films by magnetron sputtering

Many applications of boron carbide (B4C) films entail deposition on non-planar substrates, necessitating a better understanding of oblique angle deposition phenomena. Here, we systematically study the effect of substrate tilt on properties of B 4 C films with thicknesses up to 10 μm deposited by direct current magnetron sputtering. Results show that all films are amorphous and columnar with an average column width of ~100 nm, independent of substrate tilt. Column tilt angles are limited to ~20° even for substrate tilt of 80°. Film density, residual stress, and the refractive index weakly (within ≲20%) depend on substrate tilt. Furthermore, oxygen impurities bond preferentially with carbon atoms in inter-columnar regions. Substrate tilt has a major effect on mechanical properties that decrease by ~50%, suggesting weak interconnection between nano-columns. Implications of these observations for the deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Gold-tantalum alloy films deposited by high-density-plasma magnetron sputtering

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. Here, we systematically study the effects of substrate tilt (0°–80°) and negative substrate bias (0–100 V) on properties of ≲3-μm-thick films deposited by high-power impulse magnetron sputtering (HiPIMS) from a Au–Ta alloy target (with 80 at. % of Ta). Results reveal that, for all the substrate bias values studied, an increase in substrate tilt leads to a monotonic decrease in film thickness, density, residual compressive stress, and electrical conductivity. Larger substrate bias favors the formation of a body-centered cubic phase, with films exhibiting lower column tilt and higher density, electrical conductivity, and residual compressive stress. Furthermore, these changes are attributed to metal atom ionization effects, based on the lack of correlation with distributions of landing energies and incident angles of depositing species as calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. By varying substrate tilt and bias in HiPIMS deposition, properties of Au–Ta alloy films can be controlled in a very wide range, including residual stress from –2 to +0.5 GPa, density from 12 to 17 g/cm 3 , and the electrical resistivity from 50 to 4500 μΩ cm, enabling optimum deposition conditions to be selected for specific applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Deposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects

Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. In this work, we study the deposition of AuTa 4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa 4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Combinatorial Deposition of Ultrathick Ta-W-Au-Bi High-Entropy Alloys for Next-Generation Hohlraums by Direct-Current Magnetron Sputtering

Hohlraum temperature calculations with the model by J. H. Hammer and M. D. Rosen predict a higher X-ray drive from Ta-W-Au-Bi high-entropy alloys compared to pure Au and recently developed Ta 4 Au and Au-Bi hohlraums. Here, we study the microstructure and properties of 25-75−µm-thick Ta-W-Au-Bi alloy films deposited via combinatorial direct-current magnetron sputtering. All of the films have promising physical properties, including high electrical resistivity, that satisfy the requirements for magnetically assisted inertial confinement fusion experiments. While porosity tends to increase with increasing Bi content, we also found that films with Bi content > 44 at. % exhibited densification close to the substrate/film interface and formed a single-phase alloy. In conclusion, these findings provide a potential path forward for the development of Ta-W-Au-Bi alloys for next-generation hohlraum materials.

Magnetron sputtering↗
DOE OSTI2025

High-rate deposition of ultrathick bismuth films by direct-current magnetron sputtering

Bismuth coatings deposited at room temperature by physical vapor deposition typically feature irregularly-shaped grains and a high density of voids, thereby preventing their use in many potential applications. Here, we demonstrate the deposition of low-stress, high-density 40-μm-thick Bi films by systematically studying the effect of the deposition rate and substrate tilt on the properties of Bi films deposited at room temperature by direct-current magnetron sputtering. Furthermore, results show that, with increasing deposition rate, the morphology, structure, and properties of Bi films greatly improve, while an increase in substrate tilt leads to a monotonic decrease in film thickness, density, and electrical conductivity.

Bismuth↗
DOE OSTI2020

Grid-assisted magnetron sputtering deposition of nitrogen graded TiN thin films

Titanium Nitride (TiN) films were obtained using the grid-assisted magnetron sputtering deposition technique on Al substrates in two conditions: under constant and variable nitrogen concentration along the thin solid film thickness. The formation of a film with variable N concentration (herein referred as graded film) was confirmed using energy filtered transmission electron microscopy, X-ray photoelectron spectroscopy and grazing incidence X-ray diffraction. The TiN thin films microstructures were also analysed using scanning and transmission electron microscopies (SEM and TEM). Finally, the viability of synthesizing TiN thin films with variable N concentration is herein proposed as an alternative method for tailoring the properties of such functional coating materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Deposition of very thick Mo/Al multilayer films using magnetron sputtering

To understand materials at extreme conditions dynamic ramp compression techniques/experiments are critical, and gradient density impactors (GDIs) have the potential to enable high quality experiments. Very thick (i.e., hundreds of μm thick) multilayer films consisting of high z/low z layers with a gradient in z through the stack can serve as a GDI. Surprisingly while there is a large amount of literature on the topic of multilayer films, there is an absence of literature on very thick multilayer films. A number of multilayer film systems deposited by dc magnetron sputtering were evaluated as potential candidates, including Cu/Al, Ta/Al, and Mo/Al. The Mo/Al multilayer system was observed to be the most promising candidate and is the primary focus of this paper. Mo/Al multilayer films up to ∼400 μm thick with reasonable thickness uniformity were deposited.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Effects of growth rate and dynamic substrate tilt on properties of Au-Ta alloy films deposited by high-power impulse magnetron sputtering

Gold-tantalum (Au—Ta) alloys are promising for next-generation hohlraums for magnetically-assisted indirect-drive inertial confinement fusion. Hohlraum fabrication involves sputter deposition of ultrathick coatings on sphero-cylindrical substrates. The control of physical properties of such coatings remains a challenge. Here, in this work, we systematically study effects of the growth rate and dynamic substrate tilt on properties of AuTa 4 films deposited onto rotating planar substrates mounted at different tilt angles to mimic different regions of the sphero-cylindrical surface of a hohlraum. We use high-power impulse magnetron sputtering (HiPIMS) in the constant charge per pulse mode with a pulse duration of 100 μs, a charge per pulse of 190 μC, a peak target current of about 3 A, and the pulse frequency varied in the range of 400–1400 Hz. The Langmuir probe, mass-resolved ion energy spectrometry, and optical emission spectroscopy are used to monitor plasma discharge characteristics in order to isolate and study effects of the growth rate. The deposition rate and the ballistics and energetics of depositing species are estimated by Monte Carlo simulations. Results show that the film microstructure, crystallographic phase, residual stress, and electrical resistivity strongly depend on both the deposition rate and substrate tilt, highlighting their critical role in tailoring properties of Au—Ta films during hohlraum fabrication.

36 MATERIALS SCIENCE↗