Search NASA⌕ Search

SEARCH · Search NASA

Results for “metal impurities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effect of lithium coating on long pulse high performance plasma discharges in EAST

Control of impurities, fuel recycling and hydrogen content by lithium evaporative coatings and real-time lithium powder injection (LPI) in EAST are studied for high performance H-mode discharges of up to ~100 s. The results show that the lithium evaporative coatings significantly reduced both the low-Z impurity carbon and high-Z impurity tungsten as well as molybdenum concentration in the plasmas, and the impurities concentration significantly reduced with the accumulated lithium coatings and maintained well afterwards. Specifically the high-Z tungsten core impurity concentration was maintained between 3 ppm–15 ppm during the 101 s H-mode discharge, which is acceptable for the long pulse operation. In addition, real-time wall conditioning via LPI successfully reduced the core high-Z metal impurities by 50% during ~35 s long pulse H-mode discharge, exhibiting strong compatibility between real-time LPI with long pulse discharges. In addition, evaporative lithium coatings demonstrated fuel recycling control, with fuel recycling obviously reducing with lithium coatings and maintaining well afterwards. Also, the lithium evaporative coatings reduced the hydrogen minority species content, represented by the density ratio H/(H + D), from ~50% down to ~5% with accumulated lithium coatings; low hydrogen fraction improved the ICRF minority heating efficiency. Finally the real-time LPI reduced the recycling coefficient R global from 0.95 to 0.82. With these wall conditionings help, the plasma density controlled well during the 101 s long pulse H-mode discharge. Furthermore, these results provide valuable references on impurities, fuel recycling and hydrogen content control for future longer pulse high performance H-mode operation (≥400 s) in EAST and future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Mg vacancy and impurity-limited MgO single crystal thermal conductivity

Magnesium oxide (MgO) exhibits one of the highest thermal conductivities among oxides and is widely used as a dielectric material and substrate in semiconductor devices, in refractory applications, and as a promising filler in thermal interface materials for electronics. Its high thermal conductivity may be sensitive to impurity and defects, yet this influence is still uncertain. Here, in this study, the impact of the common impurities, i.e., Al, Ca, Ti, V, Fe, Si, B, Nb, Zr, Na, and K, as well as Mg and O vacancies on phonon scattering and thermal conductivity of MgO is studied using a fully first-principles T-matrix framework. It is found that B, Nb, and Zr impurities, along with Mg vacancies, lead to exceptionally strong reductions in thermal conductivity. By contrast, O vacancies and other impurities have modest to minimal impacts. Leveraging the T-matrix results, we reassess the perturbative, mass-only formalism whose use is pervasive in the literature and show that neglecting bond disorder does not necessarily lead to underestimation: for all transition-metal impurities studied, bond perturbations partially cancel mass disorder, causing the traditional perturbative model to overestimate scattering. We propose a simple modified perturbative expression that incorporates both mass and bond disorder and closely reproduces the T-matrix trends. Our predicted low-temperature trends by including phonon-impurity and phonon-boundary scattering match reasonably well with experiments. This work provides an in-depth study of impurity- and vacancy-limited thermal conductivity of MgO and suggests that reported “high-purity” MgO values have likely not yet reached the intrinsic upper limit, which may be substantially higher.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Opposing Effects of Impurity Ion Sr 2+ on the Heterogeneous Nucleation and Growth of Barite (BaSO 4 )

Nucleation of barite (BaSO 4 ) has broad implications in geological, environmental, and materials sciences. While impurity metals are common, our understanding of how they impact nucleation remains dim. In this work, we used classical optical microscopy compared to fast X-ray nanotomography (XnT) to investigate heterogeneous nucleation of barite on silica in situ with Sr 2+ as an impurity ion. The observed barite nucleation rates were consistent with classical nucleation theory (CNT), where barite crystals displayed a nonuniform size distribution, exhibiting distinct morphologies and incubation periods in Sr-free solutions. While undetectable with optical microscopy, nanotomography revealed that addition of Sr2+ enhances nucleation rates driven by the pre-factor in CNT, likely because both adsorbed Ba 2+ and Sr 2+ act as precursor sites on which nucleation occurs. Sr 2+ simultaneously inhibits growth, however, leading to a homogeneous distribution of smaller crystals. This finding will enable an improved predictive understanding of nucleation in natural and synthetic environments.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Improved 140 Nd Production for the 140 Nd/ 140 Pr In Vivo Generator through Target Recycling and Radiochemical Optimization

Theranostic strategies that utilize f-block therapeutic radionuclides, including 161 Tb, 177 Lu, 225 Ac, and 227 Th, suffer from a shortage of positron emission tomography (PET) imaging counterparts in the same chemical space and often rely on 68 Ga as a surrogate. The 140 Nd/ 140 Pr in vivo PET generator, which belongs to the f-block, may address this issue and can be produced via the 141 Pr(p,2n) 140 Nd production route by using medium-energy cyclotrons. However, impurities in the target material, including stable Nd, and the inherent difficulty of adjacent lanthanide separations limit the achievable radionuclidic and chemical purity of 140 Nd. In this work, we address these challenges through the purification and recycling of praseodymium target material and optimization of Nd/Pr separation. The resulting purified 140Nd was evaluated using DOTA and Macropa chelators via radiolabeling and in vitro stability studies. A target material purification and recycling method was developed for the monoisotopic 141 Pr starting material to remove stable Nd impurities, yielding 90.3 ± 4.7% (n = 3) recovery. The purified 141 Pr was isolated as Pr 6 O 11 and irradiated with 24 MeV protons (20.07 MeV at the target surface) at 20 μA for 4 h, which produced 1417.0 ± 83.4 MBq (38.3 ± 2.2 mCi) of 140 Nd at the end of bombardment (EOB). The produced 140 Nd was purified through an optimized DGA normal method to recover 71.6 ± 6.3% pure 140 Nd. The amount of stable Nd reduced progressively in each target purification cycle from >340 ppm without purification to <250 ppb after three cycles, while other measured metallic impurities were below 30 ppb. This improvement in target purity was reflected in the direct increase of apparent molar activity (AMA), when purified 140 Nd was evaluated with DOTA and Macropa chelators. AMA of [ 140 Nd]Nd-DOTA and [ 140 Nd]Nd-Macropa increased from 70.3 MBq/μmol (1.9 mCi/μmol) and 74 MBq/μmol (2.0 mCi/μmol) to 8025.3 MBq/μmol (216.9 mCi/μmol) and 8473.0 MBq/μmol (229.0 mCi/μmol), respectively, after the third target purification cycle. Further evaluation of chelator-labeled 140 Nd showed that [ 140 Nd]Nd-DOTA was stable in phosphate-buffered saline (PBS), saline, human serum, and mouse serum, whereas [140Nd]Nd-Macropa was stable in all except human serum. This work established a practical methodological advance for the production of 140 Nd/ 140 Pr in vivo PET generators, combining optimized target recycling and radiochemical separation to enable scaled-up and high-molar activity 140 Nd suitable for preclinical imaging. These advances support broader development of 140 Nd/ 140 Pr as a robust PET analogue, especially for f-block therapeutics.

Irradiation↗
DOE OSTI2023

Optimized purification methods for metallic contaminant removal from directly recycled Li-ion battery cathodes

Metallic contaminants pose a significant challenge to the viability of directly recycling Li-ion batteries. To date, few strategies exist to selectively remove metallic impurities from mixtures of shredded end-of-life material (black mass; BM) without concurrently damaging the structure and electrochemical performance of the target active material. We herein present tailored methods to selectively ionize two major contaminants—Al and Cu—while retaining a representative cathode (LiNi 0.33 Mn 0.33 Co 0.33 O 2 ; NMC-111) intact. This BM purification process is conducted at moderate temperatures in a KOH-based solution matrix. We rationally evaluate approaches to increase both the kinetic corrosion rate and the thermodynamic solubility of Al 0 and Cu 0 , and evaluate the impact of these treatment conditions on the structure, chemistry, and electrochemical performance of NMC. Specifically, we explore the impacts of chloride-based salts, a strong chelating agent, elevated temperature, and sonication on the rate and extent of contaminant corrosion, while concurrently evaluating the effects on NMC. The reported BM purification process is then demonstrated on samples of “simulated BM” containing a practically relevant 1 wt% concentration of Al or Cu. Increasing the kinetic energy of the purifying solution matrix through elevated temperature and sonication accelerates the corrosion of metallic Al and Cu, such that ∼100% corrosion of 75 μm Al and Cu particles is achieved within 2.5 hr. Further, we determine that effective mass transport of ionized species critically impacts the efficacy of Cu corrosion, and that saturated Cl – hinders rather than accelerates Cu corrosion by increasing solution viscosity and introducing competitive pathways for Cu surface passivation. The purification conditions do not induce bulk structural damage to NMC, and electrochemical capacity is maintained in half-cell format. Testing in full cells suggests that a limited quantity of residual surface species are present after treatment, which initially disrupt electrochemical behavior at the graphite anode but are subsequently consumed. Process demonstration on simulated BM suggests that contaminated samples—which prior to treatment show catastrophic electrochemical performance—can be recovered to pristine electrochemical capacity. The reported BM purification method offers a compelling and commercially viable solution to address contamination, particularly in the “fine” fraction of BM where contaminant sizes are on the same order of magnitude as NMC and where traditional separation approaches are unfeasible. Thus, this optimized BM purification technique offers a pathway towards viable direct recycling of BM feedstocks that would otherwise be unusable.

25 ENERGY STORAGE↗
DOE OSTI2024

The Defects Genome of Janus Transition Metal Dichalcogenides

2D Janus Transition Metal Dichalcogenides (TMDs) have attracted much interest due to their exciting quantum properties arising from their unique two-faced structure, broken-mirror symmetry, and consequent colossal polarization field within the monolayer. While efforts are made to achieve high-quality Janus monolayers, the existing methods rely on highly energetic processes that introduce unwanted grain-boundary and point defects with still unexplored effects on the material's structural and excitonic properties Through high-resolution scanning transmission electron microscopy (HRSTEM), density functional theory (DFT), and optical spectroscopy measurements; this work introduces the most encountered and energetically stable point defects. It establishes their impact on the material's optical properties. HRSTEM studies show that the most energetically stable point defects are single (V S and V Se ) and double chalcogen vacancy (V S −V Se ), interstitial defects (Mi), and metal impurities (MW) and establish their structural characteristics. DFT further establishes their formation energies and related localized bands within the forbidden band. Cryogenic excitonic studies on h-BN-encapsulated Janus monolayers offer a clear correlation between these structural defects and observed emission features, which closely align with the results of the theory. Finally, the overall results introduce the defect genome of Janus TMDs as an essential guideline for assessing their structural quality and device properties.

2D materials↗
DOE OSTI2023

Corn stover‐derived porous carbon for asymmetric supercapacitors

In this investigation, hydrothermal liquefaction‐derived hydrochar from pulverized corn stover (avg. particle size 1.12 mm and ash content 6.75 wt%) is chemically activated with aqueous KOH in the presence of Pluronic F127 surfactant and thermally treated further up to 800°C to generate porous carbon (POC) with higher specific surface area and porosity. POC obtained under different processing conditions is thoroughly characterized by Brunauer‐Emmett‐Teller surface area analyzer, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Metallic impurity present in POC is characterized by inductively coupled plasma mass spectrometry. Higher specific surface area POC is observed with the use of the surfactant during the activation process. Fully characterized POC is used with (Mn, Ti)‐mixed oxide electrode to fabricate asymmetric supercapacitor (ASC). Specific capacitance of ASC is measured by cyclic voltammetry (CV) technique using Gamry G‐300 potentiostat/galvanostat/ZRA. CV plots are obtained with different voltage scan rates whereas galvanostatic charge‐discharge plots are studied by varying the current density. Renewable corn stover‐derived POC prepared using Pluronic F127/KOH activation method is found to be highly suitable as an electrode material because of higher capacitance and electrochemical stability over 100 charging‐discharging cycles.

25 ENERGY STORAGE↗
DOE OSTI2024

Effect of Iron Contamination and Polysilicon Gettering on the Performance of Polysilicon‐Based Passivating Contact Solar Cells

Over the past decade, silicon solar cells with carrier-selective passivating contacts based on polysilicon capping an ultra-thin silicon oxide (commonly known as TOPCon or POLO) have demonstrated promising efficiency potentials and are regarded as an evolutionary upgrade to the PERC (passivated emitter and rear contact) cells in manufacturing. The polysilicon-based passivating contacts also exhibit excellent gettering effects that relax the wafer and cleanroom requirements to some extent. Here, in this work, we experimentally explore the impact of bulk iron contamination and polysilicon gettering on the passivation quality of the polysilicon/oxide structure and the resulting solar cells performance. Results show that both n- and p-type polysilicon/oxide passivating contacts are not affected by iron gettering, demonstrating robust and stable passivation quality. However, for a very high bulk iron contamination (1 × 10 13 cm −3 ), the accumulated iron in the p-type lightly boron-doped emitter in crystalline silicon would degrade the emitter saturation current density. This can cause a reduction in both open-circuit voltage and short-circuit current. Meanwhile, this very high iron content (1 × 10 13 cm −3 ) can further degrade the fill factor and temperature coefficient of the cells. On the other hand, for an initial iron content of 2 × 10 12 cm −3 , which should be well above the iron level in the current industrial Czochralski silicon wafers, the resulting cells demonstrate similar performance as the control group with no intentional iron contamination. This work brings attention to both the benefits of polysilicon gettering effects as well as the potential degradation due to the accumulation of metal impurities in the p-type emitter region.

14 SOLAR ENERGY↗
DOE OSTI2023

Corrosion characteristics of monolithic SiC materials in beryllium-bearing molten fluoride salt

In this work, chemical vapor deposited SiC single crystal and polycrystals were exposed to a static beryllium-bearing molten fluoride salt, 2LiF–BeF 2 for 500 and 1000 h at 750 °C. Overall, the single crystal and polycrystalline SiC materials experienced slight weight loss and nominal surface etching regardless of the material type. Localized pitting and nonuniform Si removal from surface regions were associated with trace metal impurities and oxygen. Cross-sectional observation revealed minimal subsurface changes in the microstructure. The corrosion damage processes were similar to those reported for molten LiF–KF–NaF salt with trace impurities, indicating that the impurities significantly affect SiC corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Continuous recovery of high-purity Kraft lignin from black liquor via simultaneous, liquid-phase acidification and purification

Here, a key advantage of the Sequential Liquid-Lignin Recovery and Purification (SLRP) process for the recovery of lignin from Kraft black liquor is the precipitation of a solvated, “liquid-lignin” phase (vs. the typical solid) during the CO 2 acidification step. Here, we have discovered that this lignin can also be maintained in a solvated state during the H 2 SO 4 acidification step if aqueous acetic acid from the Aqueous Lignin Purification with Hot Agents (ALPHA) process is incorporated into the H 2 SO 4 solution. As the liquid-lignin is converted from its salt form at pH = 9.5 to its acid form at pH = 2.5, the lignin initially solvated with water becomes solvated and thus liquefied with the organic–water solution. Maintaining the lignin in a solvated liquid state has two advantages: (1) the entire SLRP + ALPHA process, from starting black liquor to final lignin product, can be operated continuously; and (2) mass transfer of metals impurities out of the liquid-lignin phase is significantly enhanced, resulting in both a cleaner Kraft lignin product (~2000 ppm Na and 0.5-1.0 % ash) and reduced water washing.

09 BIOMASS FUELS↗
DOE OSTI2023

Radiation-induced negative optical nonlinearities in fused silica, sapphire, and borosilicate glass

Here, negative nonlinear absorption is reported in neutron- and gamma-irradiated high-OH content fused silica, low-OH content fused silica, sapphire, borosilicate glass, and radiation-resistant borosilicate glass irradiated to total neutron fluences of 3.4 × 10 16 n ∙ cm –2 (42 Mrad γ), 1.7 × 10 17 n ∙ cm –2 (211 Mrad γ), and 3.6 × 10 17 n ∙ cm –2 (433 Mrad γ). Nonlinear absorption coefficients were measured via Z-scan and are on the order of – (10 –14 –10 –10 ) m∙W –1 . The Z-scan also reveals a negative nonlinear index of refraction in neutron- and gamma-irradiated radiation-resistant borosilicate glass on the order of –10 –19 m 2 ∙ W –1 . Thermal annealing at temperatures up to 800 °C is shown to restore these nonlinearities to their positive unirradiated values in all four materials. All Z-scan measurements were performed at 532 nm with a nanosecond pulsed laser. The occurrence of negative nonlinearities may be attributed to the presence of metallic impurities and the resulting saturable absorption. A limited effect of photobleaching is observed in measurements and is quantified in multiple Z-scans.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of Cr(III) Adsorption on the Dissolution of Boehmite Nanoparticles in Caustic Solution

Incorporation of relatively minor impurity metals onto metal (oxy)hydroxides can strongly impact solubility. In complex highly alkaline multicomponent tank waste such as that at the Hanford Nuclear Reservation, tests indicate that the surface area-normalized dissolution rate of boehmite ($γ$-AlOOH) nanomaterials is at least an order of magnitude lower than that predicted for the pure phase. In this work we examine the dissolution kinetics of boehmite coated by adsorbed Cr(III), which adheres at saturation coverages as sparse chemisorbed monolayer clusters. Using 40 nm boehmite nanoplates as a model system, temperature-dependent dissolution rates of pure versus Cr(III)-adsorbed boehmite showed that the initial rate for the latter is consistently several times lower, with an apparent activation energy 16 kJ·mol -1 higher. Although the surface coverage is only around 50%, solution analytics coupled to multimethod solids characterization reveals a phyicochemical armoring effect by adsorbed Cr(III) that substantially reduces the number of dissolution-active sites on particle surfaces. Such findings could help improve kinetics models of boehmite and/or metal ion adsorbed boehmite nanomaterials, ultimately providing a stronger foundation for the development of more robust complex radioactive liquid waste processing strategies.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Elucidating the Structural and Electronic Effects of Ni and Mn Cationic Incorporation on CoOOH for Efficient Benzyl Alcohol Electrooxidation

Transition-metal oxyhydroxides such as CoOOH are promising low-cost electrocatalysts for the selective electrooxidation of organic molecules, yet the influence of ubiquitous transition-metal impurities on their performance and durability remains poorly understood. Here, we experimentally probed the individual and synergistic electrochemical and structural effects of Ni and Mn incorporations into model CoOOH electrocatalysts toward an efficient benzyl alcohol oxidation reaction (BAOR). Comprehensive electrochemical, microscopic, and spectroscopic analyses reveal that Ni incorporation enhances charge-transfer kinetics and overall activity through the formation of catalytically active Ni 3+ sites, whereas Mn exhibited a more complex but interesting role. At the early stages of operation, Mn 4+ acts as a stabilizing surface layer that mitigates catalyst degradation but partially blocks Co sites before they undergo gradual leaching. The concurrent incorporation of both Ni and Mn yields a trimetallic 2NMC@NF electrocatalyst that integrates the activity benefits of Ni with the stability conferred by Mn, achieving 92.9% benzyl alcohol conversion and 91.4% Faradaic efficiency after 24 h at 1.5 V vs RHE. These findings elucidate how trace Ni and Mn impurities, often introduced from electrolytes or external sources, can modulate the lattice and electronic structure of CoOOH, offering a design strategy for enhancing both activity and long-term stability in electrocatalytic organic oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Electrochemical carbon deposition from CO 2 in molten carbonates: substrate-dependent growth

Electrochemical carbon deposition from molten carbonate salts using inert electrodes and no additional catalyst is systematically examined. At sufficiently cathodic potentials, carbon formation occurs within 30 min and transitions from substrate-dependent nucleation to carbon-on-carbon growth. Although deposits formed on either mild-steel or graphite cathodes exhibit comparable thicknesses and salt contents, their macrostructures differ, reflecting differences in early-stage growth rates and surface chemistry. Characterization by ICP-OES, Raman spectroscopy, SEM/EDS, synchrotron powder X-ray diffraction, and C K-edge X-ray absorption near edge structure reveals that the as-deposited carbon is predominantly disordered sp 2 -bonded material. However, post-treatment reveals latent turbostratic ordering in select samples, indicating that short-range order is established during deposition but is obscured by an entrained electrolyte and kinetically formed amorphous phases. No anode-derived contamination is detected, and carbon grown on graphite cathodes shows minimal metallic impurities. These results clarify the role of cathode surface chemistry and provide pathways for controlling electrode-derived impurity incorporation and carbon structure in catalyst-free molten carbonate systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Assessment of deep levels with selenium concentration in Cd 1–x Zn x Te 1–y Se y room temperature detector materials

Incorporation of Se into Cd 1–x Zn x Te (CZT) to form the quaternary compound semiconductor Cd 1–x Zn x Te 1–y Se y (CZTS) has proven to be an effective solution for compensating the major flaws associated with CZT, including poor homogeneity and high concentrations of electronically active deep levels that limit the performance of CZT detectors. In order to investigate how deep levels are affected by the Se concentration in CZTS, we performed photoinduced current transient spectroscopy (PICTS) measurements on CZTS crystals grown by the traveling heater method (THM) with 10% atomic Zn and varying atomic percentage of Se from 1.5% to 7.0%. The PICTS scans for up to 4% Se showed an exponential reduction in the capture cross section of deep levels associated with Te secondary phases in conjunction with an increase in a deep level positioned near the mid-gap, which initially increases the electron trapping time before degrading again at higher Se concentrations. The PICTS peaks present in 7% Se were anomalous relative to the other crystals and are expected to originate from transition metal impurities found in the lower-purity CdSe precursor material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Investigation of magnetic and electrical transport properties of YMB 4 (M = Cr, Fe, and Co) compounds

We have studied the structural, magnetic, and electrical transport properties of the YMB 4 series of compounds (M= Cr, Fe, and Co). These materials exhibit high stability and possess notable refractory and thermoelectric properties. Furthermore, recent theoretical predictions suggest that some of these compounds may display quantum magnetism and dimer formation among the magnetic ions. We have synthesized almost single phase YMB 4 compounds in the orthorhombic crystal structure (space group Pbam) using arc-melting and annealing. The Rietveld analysis of the room-temperature X-ray diffraction patterns reveals a clear change in the lattice parameter c, which correlates with the atomic radii of Cr, Fe, and Co. The temperature variation of resistivity measured between 2 K and 300 K reveals a metallic electron transport in all three YMB 4 compounds. However, no abrupt change in resistivity due to structural or magnetic phase transitions is observed. Additionally, a weak positive magnetoresistance of 1%–2% has been measured at 2.5 K, the contribution from the metallic impurity cannot be ruled out. The carrier concentration, on the order of 10 21 cm −3 , has been determined using conventional Hall measurements. The thermomagnetic curves recorded between 2 K and 350 K reveal the non-magnetic behavior of all these compounds. However, a small magnetic moment from paramagnetic/ferromagnetic impurity phases is detected at low temperatures. Above room temperature, no magnetic transition associated with the breaking of a dimer is observed.

borides↗
DOE OSTI2020

Influence of Tabula Rasa on Process- and Light-Induced Degradation of Solar Cells Fabricated From Czochralski Silicon

Monocrystalline Si solar cells are fabricated from Czochralski (Cz) Si, which contains 10 17 –10 18 cm -3 oxygen atoms. Cz Si undergoes degradation during high-temperature thermal processing steps, such as dopant diffusion to form the p - n junction. This degradation in the bulk minority carrier lifetime can be related to the formation of oxygen precipitates. We found that a high-temperature annealing process known as tabula rasa (TR) not only mitigates process-induced degradation via oxygen precipitate nuclei dissolution, but also modifies subsequent light-induced degradation. We report on the bulk carrier lifetime of n - and p -type Cz Si after TR, which homogenizes the interstitial oxygen in the bulk Si to its monoatomic form in either an N 2 or O 2 environment. A control sample, which was not subjected to a TR processing step, experienced severe process-induced degradation during a boron emitter thermal budget as oxygen precipitates were formed in the Si bulk. These precipitates could be imaged using photoluminescence. Additionally, samples that underwent a TR processing step prior to the boron emitter thermal budget show efficient gettering of metallic impurities compared to the control sample, which showed a decline in the implied open-circuit voltage after the gettering step. Furthermore, modification of the interstitial oxygen bonding by TR had a strong effect on the light-induced degradation kinetics. Instead of a typically observed monotonic decrease, minority carrier lifetime increases first, followed by a nonmonotonic decrease over a ~20 h period. Finally, we conclude that by modifying the interstitial oxygen bonding via TR pretreatment, p -type Cz Si wafers become substantially resistant to harsh solar cell processes and strongly modified light-induced degradation, which would open alternative ways to mitigate this degradation mechanism.

14 SOLAR ENERGY↗
DOE OSTI2022

Gamma-radiation-induced negative nonlinear absorption in quartz glass

The effect of ionizing radiation on the nonlinear optical properties of materials needs to be considered for applications that employ high-power laser pulses in extreme radiation environments. The Heraeus Infrasil302 optical quartz glass was irradiated by gamma rays, and its nonlinear absorption was measured using the open-aperture Z-scan technique with nanosecond laser pulses. Irradiation results in a negative nonlinear absorption coefficient whose magnitude increases with irradiation dose. Nonlinear absorption coefficients of -0.78, -1.14, -1.29, and -1.88~ × ~10 -13 m/W are measured for gamma doses of 600 krad, 1.2 Mrad, 3.6 Mrad, and 10 Mrad, respectively. Thermal annealing restores the optical properties of quartz-glass to their unirradiated values. It is suggested that metallic impurities introduced by the manufacturing process have a role in inducing saturated absorption in irradiated quartz glass, which manifests as negative nonlinear absorption coefficient, and is demonstrated by comparing Infrasil302 quartz results to equivalent irradiated measurements for Spectrosil2000 quartz.

07 ISOTOPE AND RADIATION SOURCES↗