Search NASA⌕ Search

SEARCH · Search NASA

Results for “molecular doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Ultrafast Charge Transfer Dynamics at the Origin of Photoconductivity in Doped Organic Solids

In spite of their growing importance for optoelectronic devices, the fundamental properties and photophysics of molecularly doped organic solids remain poorly understood. Such doping typically leads to a small fraction of free conductive charges, with most electronic carriers remaining Coulombically bound to the ionized dopant. Recently, we have reported photocurrent for devices containing vacuum-deposited TAPC (1,1-bis(4-bis(4- methylphenyl)aminophenyl)cyclohexane) doped with MoO 3 , showing that photoexcitation of charged TAPC molecules increases the concentration of free holes that contribute to conduction. Here, we elucidate the excited-state dynamics of such doped TAPC films to unravel the key mechanisms responsible for this effect. We demonstrate that excitation of different electronic transitions in charged and neutral TAPC molecules allows bound holes to overcome the Coulombic attraction to their MoO 3 counterions, resulting in an enhanced yield of long-lived free carriers. This is caused by ultrafast back-and-forth shuffling of charges and excitation energy between adjacent cations and neutral molecules, competing with relatively slow nonradiative decay from higher excited states of TAPC •+ . The light-induced generation of conductive carriers requires the coexistence of cationic and neutral TAPC, a favorable energy level alignment, and intermolecular interactions in the solid state.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Subsurface spectroscopy of heterogeneous materials using optical wavefront shaping

Plastic-bonded explosives and propellants consist of energetic molecular crystals embedded in a polymer matrix that also includes additives, such as taggants, plasticizers, grit, antioxidants, etc. Furthermore, this heterogeneous composition renders these materials optically opaque, limiting optical characterization techniques (e.g., Raman spectroscopy) to probing chemical reactions at the sur-face. However, many reactions of interest are believed to occur inside the material where current optical techniques can not probe. To address this challenge, we have developed a new optical technique that utilizes feedback assisted wavefront shaping (using spatial light modulators) to focus probe light inside a heterogeneous material, such that we can perform subsurface spectroscopy. Recently, we demonstrated this technique by monitoring subsurface photodegradation and thermal degradation of Eu-doped molecular crystals using both fluorescence and Raman spectroscopy. Based off these successes we are now looking into improvements to this technique to allow for greater time resolution, including replacing our spatial light modulators with fast digital mirror devices, using ns optical phase conjugation, and self-healing optical beams.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Unavoidable multilevel biaxial symmetry breaking in chiral hybrid liquid crystals

Chiral nematic or cholesteric liquid crystals (LCs) are fluid mesophases with long-ranged orientational order featuring a quasilayered periodicity imparted by a helical director configuration but lacking long-range positional order. Doping molecular cholesteric LCs with strongly anisotropic uniaxial colloidal particles adds another level of complexity because of the interplay between weak surface-anchoring boundary conditions and bulk-based elastic distortions near the particle-LC interface. Using cylindrical colloidal disks and rods with different geometric shapes and surface conditions, we demonstrate that these colloidal inclusions generically exhibit biaxial orientational probability distributions which may impart anomalously strong local biaxiality onto the hybrid cholesteric LC structure. Unlike nonchiral hybrid molecular-colloidal LCs, where biaxial order emerges only at critical colloid volume fractions exceeding some uniaxial-biaxial transition value, the orientational probability of the colloidal inclusions immersed in chiral nematic hosts is unambiguously biaxial even at infinite dilution. We demonstrate that the colloids induce local biaxial perturbations within the molecular orientational order of the LC host medium which strongly enhances the weak but native biaxial order of chiral nematic LC induced by the chiral symmetry breaking of the director field. With the help of analytical modeling and computer simulations based on the Landau–de Gennes free energy of the host LC around the colloids, we rationalize the observed multilevel biaxial order and conclude that it is not only unavoidable but also strongly enhanced compared to both achiral hybrid LCs and purely molecular cholesteric LCs.

biaxial liquid crystals↗
DOE OSTI2020

Enhanced Catalytic Activity of a Vanadium-Doped Mesoporous Octahedral Molecular Sieve-2 (K-OMS-2) toward Hydrogen Evolution Reaction

Hydrogen evolution reaction (HER) is the cathodic reaction in electrochemical water splitting that produces H 2 in a renewable pathway, primarily to be used in fuel cells. K-OMS-2, a manganese octahedral molecular sieve, has the potential to replace Pt as a catalyst for HER due to its redox and electrochemical properties, which can be further improved by doping metal cations into the K-OMS-2 framework. In this work, we synthesized 1, 5, and 10% vanadium- (V) doped mesoporous K-OMS-2 under mild acidic reaction conditions. Here, the mesoporous nature of the samples was confirmed by BET analysis. X-ray photoelectron spectroscopy confirmed that Mn has 2+, 3 +, and 4+ oxidation states, and V is present as V 4+ in V-K-OMS-2 samples. HER performance of 1% V-K-OMS-2 in an acidic medium shows the best activity with -0.32 V overpotential. The overpotential was lowered by 0.56 V upon doping 1% V into the K-OMS-2 framework. The 1% V-K-OMS-2 material has a Tafel slope of 129 mV/decay and an electrochemically active surface area (ECSA) of 127.5 cm 2 ECSA .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Water stable molecular n-doping produces organic electrochemical transistors with high transconductance and record stability

From established to emergent technologies, doping plays a crucial role in all semiconducting devices. Doping could, theoretically, be an excellent technique for improving repressively low transconductances in n-type organic electrochemical transistors – critical for advancing logic circuits for bioelectronic and neuromorphic technologies. However, the technical challenge is extreme: n-doped polymers are unstable in electrochemical transistor operating environments, air and water (electrolyte). Here, the first demonstration of doping in electron transporting organic electrochemical transistors is reported. The ammonium salt tetra-n-butylammonium fluoride is simply admixed with the conjugated polymer poly(N,N’-bis(7-glycol)-naphthalene-1,4,5,8-bis(dicarboximide)-co-2,2’-bithiophene-co-N,N’-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide), and found to act as a simultaneous molecular dopant and morphology-additive. The combined effects enhance the n-type transconductance with improved channel capacitance and mobility. Furthermore, operational and shelf-life stability measurements showcase the first example of water-stable n-doping in a polymer. Overall, the results set a precedent for doping/additives to impact organic electrochemical transistors as powerfully as they have in other semiconducting devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Free Energy Dependencies for Interfacial Electron Transfer from Tin-Doped Indium Oxide (ITO) to Molecular Photoredox Catalysts

John B. Goodenough proposed that interfacial electron transfer kinetics from main group metal oxides should be fundamentally different from that of transition metal oxides, an expectation that has not been widely tested. Herein, the kinetics for interfacial electron transfer from mesoporous transparent conductive oxide Tin-doped Indium Oxide (ITO) to four photoredox catalysts (PCs) were characterized in acetonitrile electrolytes. The photocatalysts had the form: [Ru(4,4ʹ-R 2 -2,2′-bipyridine) 2 (4,4ʹ-(PO 3 H 2 ) 2 -2,2′-bipyridine)] 2+ , where R was H, methoxy, tert -butyl, and Br. The impact of the surface binding group was characterized with [Ru(2,2′-bipyridine) 2 (4,4ʹ-(CO 2 H) 2 -bpy)] 2+ . The interfacial electron transfer reaction ITO(e − )∣PC + → ITO∣PC was quantified by nanosecond absorption spectroscopy as a function of the applied potential (and hence ‒Δ G °). Specific conditions of applied potential were identified where the kinetics were sensitive to the incident irradiance. A layer-by-layer method was used to insert ionic methylene bridge(s) between the PC and the oxide surface. Marcus-Gerischer analysis of the kinetic data indicates non-adiabatic interfacial electron transfer with total reorganization energies that increase when bridges were placed between the photocatalyst and the ITO surface.

Bangle, Rachel E.↗
NASA NTRS1993

Long-wavelength PtSi infrared detectors fabricated by incorporating a p(+) doping spike grown by molecular beam epitaxy

By incorporating a 1-nm-thick p(+) doping spike at the PtSi/Si interface, we have successfully demonstrated extended cutoff wavelengths of PtSi Schottky infrared detectors in the long wavelength infrared (LWIR) regime for the first time. The extended cutoff wavelengths resulted from the combined effects of an increased electric field near the silicide/Si interface due to the p(+) doping spike and the Schottky image force. The p(+) doping spikes were grown by molecular beam epitaxy at 450 C, using elemental boron as the dopant source, with doping concentrations ranging from 5 x 10 exp 19 to 2 x 10 exp 20/cu cm. Transmission electron microscopy indicated good crystalline quality of the doping spikes. The cutoff wavelengths were shown to increase with increasing doping concentrations of the p(+) spikes. Thermionic emission dark current characteristics were observed and photoresponses in the LWIR regime were demonstrated.

Lin, T. L.↗
NASA NTRS1993

Long-Wavelength PtSi Infrared Detectors Fabricated by Incorporating a P+ Doping Spike Grown by Molecular Beam Epitaxy

By incorporating a 1-nm-thick p+ doping spike at the PtSi/Si interface, we have successfullydemonstrated extended cutoff wavelengths of PtSi Schottky infrared detectors in the long wavelengthinfrared (LWIR) regime for the first time. The extended cutoff wavelengths resulted from thecombined effects of an increased electric field near the silicide/Si interface due to the p+ dopingspike and the Schottky image force. The p+ doping spikes were grown by molecular bema epitaxy at450 degrees C using elemental boron as the dopant source, with doping concentrations ranging from 5x 10^(19) to 2 x 10^(20) cm^(-3). Transmission electron microscopy indicated good crystallinequality of the doping spikes. The cutoff wavelengths were shown to increase with increasing dopingconcentrations of the p+ spikes. Thermionic emission dark current characteristics were observed andphotoresponse in the LWIR regime was demonstrated.

Maserjian, J.↗
NASA NTRS1992

Growth of a delta-doped silicon layer by molecular beam epitaxy on a charge-coupled device for reflection-limited ultraviolet quantum efficiency

Low-temperature silicon molecular beam epitaxy is used to grow a delta-doped silicon layer on a fully processed charge-coupled device (CCD). The measured quantum efficiency of the delta-doped backside-thinned CCD is in agreement with the reflection limit for light incident on the back surface in the spectral range of 260-600 nm. The 2.5 nm silicon layer, grown at 450 C, contained a boron delta-layer with surface density of about 2 x 10 exp 14/sq cm. Passivation of the surface was done by steam oxidation of a nominally undoped 1.5 nm Si cap layer. The UV quantum efficiency was found to be uniform and stable with respect to thermal cycling and illumination conditions.

Hoenk, Michael E.↗
DOE OSTI2026

Edge‐Driven Fringe‐Field Effects, Reduced Screening, and Bandgap Widening in Graphene Nanoribbons Enable Single‑Molecule Sensitivity

Graphene nanoribbons (GNRs) offer promising platforms for single‐molecule sensing due to their quasi‐1D channels and discrete electronic states, providing superior sensitivity toward molecular perturbations. While prior studies emphasize smoother edges as essential for optimal performance, the potential benefits of controlled edge roughness remain largely unexplored. Additionally, most investigations focus on GNR arrays, leaving critical edge‐ and width‐dependent factors, including fringe fields, bandgap widening, interactions between adsorbing molecules and GNR atoms, density of states (DOS) suppression, and electrostatic screening lengths, and their collective impact on sensitivity, poorly understood. Here, in this work, we fabricated field‐effect transistors using individual GNRs (widths: 200–20 nm) and characterized their response to molecular adsorption with perfluorooctanoic acid as the model analyte. Narrower ribbons displayed significantly enhanced sensitivity, yielding a coverage‐normalized response of 116 ± 10 mV per molecule in 20 nm‐wide GNRs (from calibrated ensemble Dirac‐point shifts). Experimental and theoretical analyses reveal that this heightened sensitivity arises from stronger fringe fields, width‐dependent quantum confinement effects, reduced DOS, and increased edge roughness that facilitates molecular anchoring, enhanced orbital overlap, and improved charge transfer efficiency. Our findings challenge the conventional assumption that smoother edges inherently enhance sensor performance, demonstrating that controlled edge disorder substantially boosts molecular sensitivity in GNR sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Polaron Delocalization and Transport in Doped Graphene Nanoribbon Thin Films

Graphene nanoribbons (GNRs) are quantum-confined π-conjugated monolayer semiconductors with attractive properties for optoelectronic applications. However, the ground- and excited-state properties of charge carriers in GNRs are still poorly understood, particularly with regards to the coupling between charges and the GNR lattice and the degree to which this coupling impacts local and macroscopic charge transport. To address this issue, we systematically correlate carrier density-dependent charge transport with spectroscopic modulations in chemically doped thin films of armchair graphene nanoribbons (9-aGNRs). This study combines Fourier transform infrared (FTIR) and ultraviolet−visible−near-infrared (UV−vis−NIR) spectroscopy with both local and macroscopic conductivity measurements to arrive at a full and self-consistent picture of transport in doped GNR thin films. Using three different molecular p-type dopants (i.e., oxidants), we demonstrate that hole polarons are the dominant quasi-particle determining charge transport in GNRs and that the degree of polaron delocalization depends sensitively on the dopant and the hole density. For all three dopants, the local conductivity probed by microwave spectroscopy substantially exceeds the long-range conductivity obtained by four-point probe measurements. Interestingly, the dopant size substantially influences charge transport at high hole densities. We ascribe this effect to different propensities for forming bipolarons with lower mobilities than polarons. Comparison of GNR transport and spectral properties to other prototypical π-conjugated semiconductors (e.g., semiconducting polymers or carbon nanotubes) benchmark the charge transport properties of GNR thin films for optoelectronic devices and applications.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Local rare-earth dopant structure in a complex-oxide/semiconductor heterojunction: Molecular beam epitaxy grown Yb-doped SrTiO3 on Si(001)

We have investigated the structural and electronic properties of Yb-doped SrTiO3/Si(001) grown by molecular beam epitaxy. Other rare-earth donor dopants that result in n-type conductivity typically substitute for Sr at the A-sites in the perovskite lattice. In contrast, Yb has been found to substitute predominantly for Ti at the perovskite B-sites based on data from atomically resolved scanning transmission electron microscopy and spectroscopy, as well as extended x-ray absorption fine structure. Yb exhibits two distinct charge states as determined by x-ray absorption spectroscopy and associated modeling, +2.7 and +2.1. These aliovalent substitutional dopants are compensated by donor electrons from oxygen vacancies that form during epitaxial film growth. An atom beam flux mismatch was present during film depositions because it was assumed that Yb would occupy A-sites, leading to a flux matching formula given by Yb + Sr = Ti. However, the formation of YbTi rather than YbSr results in Sr vacancies and extraneous (i.e. non-lattice) Ti atoms in the films, or on the film surfaces. The presence of these defects, together with oxygen vacancies, leads to deep-level electron traps that were detected by resonant photoemission and much higher sheet resistance than that associated with, for instance, La-doped films.

Chambers, Scott A. (ORCID:000000025415043X)↗
NASA NTRS2016

Interfacial Structure and Capacitance of Li-doped Ionic Liquid Electrolytes from Molecular Simulations

Ionic liquids have been proposed as candidate electrolytes for high-energy density, rechargeable batteries, supercapacitors, and hybrid energy storage devices. Though Li-salt is often present in these systems, its influence on interfacial properties is largely uncharacterized. We, thereby, present an extensive computational analysis, supported by experimental comparisons, of the properties of a representative set of these electrolytesat an ideal carbon interface as a function of Li-salt doping and voltage. We have performed polarizable molecular (MD) dynamics simulations, using the APPLEP force field, to evaluate electric double layer (EDL) capacitance and distribution of Li+ in the EDL. Differential capacitance exhibits the characteristic camel profile and is insensitive to Li-doping. Li+ localizes in the second molecular layer of the EDL, which is a result of confinement from free energy barriers associated with ion layering. Joint MDelectronic structure computations show the electrochemical window of the electrolytes to be a weak function of Li-doping. Estimates of supercapacitor specific energy are made using the computed window and capacitance. The magnitude and trends in specific energy are in good agreement with experiment.

batteries↗
DOE OSTI2024

Structural and optical characterization of dilute Bi-doped GaN nanostructures grown by molecular beam epitaxy

We have carried out detailed studies on the epitaxy and characterization of dilute Bi-doped GaN nanostructures. A comprehensive investigation of Bi-doped GaN nanowires and quasi-film epitaxial growth conditions has been performed. Scanning electron microscopy studies show that lowering the GaBiN growth temperature causes gradual changes in top c-plane nanowire morphology due to the incremental incorporation of foreign Bi atoms. This trend is further substantiated by the secondary ion mass spectroscopy analysis of a multi-layer Bi-doped GaN quasi-film. However, it is also found that the amount of Bi incorporation into the GaN lattice is relatively independent of the N2 flow rate variation under the growth conditions investigated. Furthermore, room-temperature micro-Raman spectra show that there are additional peaks near 530, 650, and 729 cm−1 wave numbers in the Bi-doped GaN samples, which can primarily be attributed to Bi local vibrational modes, indicative of a small amount of Bi incorporation in the GaN lattice. Moreover, phonon calculations with density functional theory indicate that Bi replacing the N sites is the likely origin of the experimentally measured Raman modes. X-ray photoelectron spectroscopy measurements have also been obtained to deduce the electronic interaction between the Bi dopant atom and the GaN nanostructure. Such one-dimensional nanowires permit the synthesis of dislocation-free highly mismatched alloys due to strain relaxation, allowing efficient light absorption and charge carrier extraction that is relevant for solar energy harvesting and artificial photosynthesis.

Materials Science↗
DOE OSTI2022

β -Ga 2 O 3 MESFETs with insulating Mg-doped buffer grown by plasma-assisted molecular beam epitaxy

In this work, we develop in situ Mg doping techniques in plasma-assisted molecular beam epitaxy (PAMBE) of β -Ga 2 O 3 to compensate Si dopants at the substrate epilayer growth interface and eliminate parasitic leakage paths. Both abrupt and uniform Mg doping profiles over a wide range of concentrations were achieved in β -Ga 2 O 3 epilayers grown by PAMBE. Capacitance–voltage characteristics of Si and Mg co-doped samples confirmed the compensating effect of the Mg dopants. Mg delta-doping was then integrated into a β -Ga 2 O 3 metal-semiconductor field effect transistor structure and shown to be effective in eliminating source leakage. In conclusion, the results presented here show that Mg doping is a promising way to engineer insulating buffer layers for β -Ga 2 O 3 lateral devices grown by PAMBE.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1989

Heavily boron-doped Si layers grown below 700 C by molecular beam epitaxy using a HBO2 source

Boron doping in Si layers grown by molecular beam epitaxy (MBE) at 500-700 C using an HBO2 source has been studied. The maximum boron concentration without detectable oxygen incorporation for a given substrate temperature and Si growth rate has been determined using secondary-ion mass spectrometry analysis. Boron present in the Si MBE layers grown at 550-700 C was found to be electrically active, independent of the amount of oxygen incorporation. By reducing the Si growth rate, highly boron-doped layers have been grown at 600 C without detectable oxygen incorporation.

Lin, T. L.↗