Search NASA⌕ Search

SEARCH · Search NASA

Results for “nmp”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Levelized Cost of CO 2 Captured Using Five Physical Solvents in Pre-combustion Applications

Aspen Plus v8.8 was used to perform techno-economic analysis (TEA) of a CO 2 capture process from a typical fuel gas stream in a 543-MW pre-combustion power plant using five different physical solvents (Selexol, PEGPDMS-1, NMP, [aPy][Tf 2 N] and [hmim][Tf 2 N]). The process included a countercurrent packed-bed absorber operating under high-pressure over a wide range of temperatures and three pressure-swing flash drums for solvent regeneration. Furthermore, two packings, Mellapak 250Y and IMTP50, were used and the Levelized costs of CO 2 captured (LCOC) were calculated. The simulation results indicated that using Mellapak 250Y exhibited lower LCOC values than those when using IMTP50 for the five solvents under all conditions used as it offered better mass transfer. The CO 2 capture process carried out at low temperatures showed lower LCOC values than those at higher temperatures due to the increased CO 2 solubility in the solvents at lower temperatures, requiring smaller absorber diameter and lower solvent circulation rates, which offset the cooling requirements. Comparing the lowest LCOC values for the five solvents, the hydrophobic PEGPDMS-1 solvent was the most promising one compared to the other four solvents, due to its lowest capital and operating costs and noncorrosive, which enabled using less expensive materials for the process equipment.

42 ENGINEERING↗
DOE OSTI2023

Influence of Methylammonium Chloride on Wide-Bandgap Halide Perovskites Films for Solar Cells

Wide-bandgap perovskites are of paramount importance as the photoactive layer of the top cell in high-efficiency tandem solar cells. Comparably high Br contents are required to widen the perovskite bandgap. However, the increase in Br content causes heterogeneous halide distribution and photoinstability. Here, in this study, the positive effect of the additive methylammonium chloride (MACl) on the optical and electronic properties of Br-rich perovskite, deposited using N-methyl-2-pyrrolidone (NMP) as co-solvent and the gas quenching method, is investigated. Simultaneous in situ grazing-incidence wide-angle X-ray scattering and photoluminescence spectroscopy are used to track the evolution of the structural and optoelectronic properties of the perovskites with different amounts of Br and MACl during the spin-coating and thermal annealing steps. The formation mechanism is elucidated in the presence of MACl. It is observed that chloride ions inhibit the intermediate phases, favoring the formation of a perovskite phase with higher crystallinity. Nano X-ray fluorescence mapping recognizes Br-richer and poorer nanometric domains, whose average sizes reduce for samples with MACl. In conclusion, it is demonstrated that adding MACl affects the formation of wide-bandgap perovskites via destabilization of the intermediate phases and acts on the homogenization of the halide distribution, leading to improved solar cell performances.

14 SOLAR ENERGY↗
DOE OSTI2020

Effects of water-based binders on electrochemical performance of manganese dioxide cathode in mild aqueous zinc batteries

In the majority of rechargeable batteries including lithium ion batteries (LIBs), polyvinylidene fluoride (PVdF) binders are the most commonly used binder for both anode and cathode. However, using PVdF binder requires the organic solvent of N-methyl-2-pyrrolidone (NMP) which is expensive, volatile, combustible, toxic, and has poor recyclability. Therefore, switching to aqueous electrode processing routes with non-toxic binders would provide a great leap forward towards the realization of ideally fully sustainable and environmentally friendly electrochemical energy storage devices. Various water-soluble binders (aqueous binders) were characterized and compared to the performance of conventional PVDF. Our study demonstrates that the electrochemical performance of Zn/MnO2 aqueous batteries is significantly improved by using sodium carboxymethyl cellulose (CMC) binder. Additionally, CMC binders offers desirable adhesion, good wettability, homogeneous material distribution, and strong chemical stability at certain pH levels (3.5~5) without any decomposition for long-cycle life.

25 ENERGY STORAGE↗
DOE OSTI2025

Revealing the Crystallization Pathways of Mixed‐Halide Low‐Dimensional Perovskites: A First Step Toward Solar Cell Applications

Ruddlesden–Popper perovskites (RPPs) are promising materials for optoelectronic devices. While iodide‐based RPPs are well‐studied, the crystallization of mixed‐halide RPPs remains less explored. Understanding the factors affecting their formation and crystallization are vital for optimizing morphology, phase purity, and orientation, which directly impact device performance. Here, we investigate the crystallization and properties of mixed‐halide RPPs (PEA) 2 FA n−1 Pb n (Br 1/3 I 2/3 ) 3n + 1 (PEA = C 6 H 5 (CH 2 ) 2 NH 3 + and FA = CH(NH 2 ) 2 + ) (n = 1, 5, 10) using DMSO ((CH 3 ) 2 SO) or NMP (OC 4 H 6 NCH 3 ) as cosolvents and MACl (MA = CH 3 NH 3 + ) as an additive. For the first time, the presence of planar defects in RPPs is directly observed by in situ grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) and confirmed through the simulation of the patterns that matched the experimental. GIWAXS data also reveals that DMSO promotes higher crystallinity and vertical orientation, while MACl enhances crystal quality but increases halide segregation, shown here by nano X‐ray fluorescence (nano‐XRF) experiments. For low‐n RPPs, orientation is crucial for solar cell efficiency, but its impact decreases with increasing n. Our findings provide insights into optimizing mixed‐halide RPPs, guiding strategies to improve crystallization, phase control, and orientation for better performance not only in solar cells but also in other potential optoelectronic devices.

Guaita, Maria G D↗
DOE OSTI2020

Evaporation due to infrared heating and natural convection

The results obtained from a drying experiment under infrared heating are compared to those obtained from correlations for the mass transfer coefficients, which are commonly used to obtain evaporation rates for drying applications. It was shown that the mass transfer coefficients evaluated by natural convection correlations are approximately ten times lower than those measured under infrared (IR) exposure. In this work, an attempt to explain this discrepancy, which has been also observed in other studies and explained on the basis of thermal radiation effects, optical properties of NMP are presented and the implications of the IR and near infrared (NIR) spectrum on the thermal radiation effects and ensuing evaporation rates are discussed. The results show that expected raise in the film temperature, which would be due to the thermal radiation effects, cannot be used to describe the measured evaporation rates for this solvent. Therefore, this study provides important evaporation mass flux data, which cannot be predicted using traditional correlations, for the design of IR assisted drying systems used in membrane fabrication.

42 ENGINEERING↗
DOE OSTI2020

Anharmonic multi-phonon nonradiative transition: An ab initio calculation approach

Nonradiative carrier recombinations at deep centers in semiconductors are of great importance for both fundamental physics and device engineering. Here, we provide a revised analysis of Huang’s original nonradiative multi-phonon (NMP) theory with ab initio calculations. First, we confirmed at the first-principles level that Huang’s concise formula gives the same results as the matrix-based formula, and that Huang’s high-temperature formula provides an analytical expression for the coupling constant in Marcus theory. Secondly, we correct for anharmonic effects by taking into account local phonon-mode variations for different charge states of a defect. The corrected capture rates for defects in GaN and SiC agree well with experiments.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Aqueous Ni-rich-cathode dispersions processed with phosphoric acid for lithium-ion batteries with ultra-thick electrodes

Lithium-ion battery (LIB) production can benefit both economically and environmentally from aqueous processing. Although these electrodes have the potential to surpass electrodes conventionally processed with N -methyl-2-pyrrolidone (NMP) in terms of performance, significant issues still exist with respect to ultra-thick cathodes ($\gg$4 mAh/cm 2 areal capacities). A major concern for these types of electrodes with high-nickel active material stems from lithium leaching from active material, which drives the pH of the dispersion in excess of 12 and subsequently corrodes the current collector interface. As this corrosion reaction proceeds, hydrogen generation at the interface creates bubbles which cause severe cracking in the dried electrode surface. When areal loadings are increased, this effect becomes more pronounced and is detrimental to both mechanical and electrochemical properties of these electrodes. In this work, a technique for mitigating corrosion at the current collector by adjusting the pH of the dispersion with the addition of phosphoric acid is investigated. Phosphoric acid was added in 0.5 wt% increments between 0.0 and 1.5 wt%, and effects on rheology, adhesion, corrosion, and electrochemical performance were investigated. A technique is reported for producing aqueous processed cathodes with areal loadings of 6–8 mAh/cm 2 with reduced surface cracking and superior high-rate discharge capacity (i.e. high-power performance) for this class of cathode loadings.

25 ENERGY STORAGE↗
DOE OSTI2020

Efficient synthesis of high-sulfur-content cathodes for high-performance Li–S batteries based on solvothermal polysulfide chemistry

A novel solvothermal polysulfide (PS) chemistry enables a facile and highly efficient process for synthesizing sulfur-carbon (S–C) composite powders containing up to 90 wt% S for high-performance Li–S batteries. Molecular dynamics calculations and experimental analyses reveal the formation of PSs upon dissolution of elemental S in N-methyl-2-pyrrolidone (NMP) at elevated temperatures and efficient infiltration of the PSs into the carbon host driven by the strong coupling with the C surfaces. The coupling enables extensive contact between S and C in the composite, leading to promising electrochemical properties for Li–S battery applications. In the power-type configuration, the composite cathodes having medium-to-high S contents (55 and 75%) demonstrate stable capacity at high current densities up to 100C (1C = 1670 mA g -1 -S) and no capacity fade up to 1000 cycles at 2C. In the energy-type configuration, a high-S-content and high-loading (90%-S, 4.2 mAh cm -2 ) cathode shows a specific capacity of 1440 mAh g -1 (86% S utilization) and 90% capacity retention after 300 cycles. This synthesis method enables significant advancement in realizing large-scale applications of Li–S batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Surface modification of cathode material enhances electrochemical performance in dry-processed Li-ion battery electrodes

The transition to electric vehicles (EVs) is pivotal for achieving energy security and integrating grid stability, with lithium-ion batteries (LIBs) playing a central role in this transformation. However, the conventional wet electrode manufacturing relying on N-methyl-2-pyrrolidone (NMP) solvent is energy intensive and costly. Dry processing (DP) has emerged as a promising alternative, eliminating solvents and using polytetrafluoroethylene (PTFE) binder for electrode fabrications. Despite its advantages, DP faces a critical challenge: poor interfacial adhesion between the hydrophobic PTFE binder and the hydrophilic cathode active material (CAM), particularly LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811), which undermines electrode performance. Here, to address this, we introduced a novel vapor-phase trimethoxymethylsilane (TMMS) coating to hydrophobize the CAM surface, enhancing compatibility with PTFE. This surface modification significantly enhances binder – CAM interactions, enabling uniform mixing and robust electrode integrity without damaging the CAM particles. Our findings advance the feasibility of environmentally sustainable and cost-effective dry processing, representing a significant step toward sustainable battery manufacturing.

Choi, Junbin [Oak Ridge National Laboratory (ORNL)↗
DOE OSTI2024

Elucidating the Role of Carbon Conductive Additive in the Processing and Electrochemical Behavior of Surface-Modified Si Anodes

In the present work, we explore the impact of conducting carbon on the processing of silicon (Si)-rich electrodes, their resulting cycling performance, and parasitic side reactions. We employed three different carbon additives, Super C45 (carbon black), Super C65 (carbon black), and TIMCAL C-NERGY KS 6L (graphite), with varying sizes and morphologies to determine how these parameters influence the structure and the electrochemical behavior of the cast electrodes. Raman mapping indicates that the improved performance achieved using C45 can be explained by the homogeneous distribution of Si and carbon, enabling the formation of continuous electrical pathways throughout the electrode. Further, this finding aligns with the results of ζ potential measurements, which indicate that C45 can maintain more stable dispersions in N-methyl-2-pyrrolidone (NMP) compared with the other carbon additives. However, electrodes with C45 as the conducting agent exhibited increased parasitic side reactions, as evidenced by the leakage current obtained from voltage hold experiments. These side reactions can have adverse effects on the calendar life of the electrode. Furthermore, the Raman maps of the electrodes reveal heterogeneities in Si and carbon distribution with lower carbon content, especially with only 2% carbon. This drastically impacts the cyclability of the electrodes, with portions of the low-carbon electrodes that remain unable to undergo cycling even at slow rates (0.2 Ah g –1 ). Additionally, we found that slower formation rates are favored in the context of parasitic side reactions, although slower formation rates can potentially create thicker passivating films that could hinder Li + -ion transport. Therefore, we emphasize the need for an intricate balance in materials selection and cycling protocol for optimal electrode processing and electrochemical behavior.

25 ENERGY STORAGE↗
DOE OSTI2020

SiO 2 Is Wasted Space in Single-Nanometer-Scale Silicon Nanoparticle-Based Composite Anodes for Li-Ion Electrochemical Energy Storage

The electrode processing conditions of silicon-based composite anodes play a pivotal role in the resulting interfacial chemical speciation and, thus, the electrochemical cycling behavior of the electrode. Systematically investigating how small chemical changes to the surface of the silicon nanoparticle (NP) affect larger, electrode-level properties is a strategy that will inform design principles to maximize electrode energy density and extend electrode lifetime. Here, we incorporate silicon nanoparticles (NPs) with an average diameter of 5.5 nm synthesized from the gas phase through a nonthermal plasma method into composite anode half-cell coin cells. We perform chemistry to functionalize the native hydride-terminated silicon NP surface with N-methylpyrrolidone (NMP) to improve slurry properties and reduce the silicon reactivity prior to composite electrode fabrication. We construct composite electrodes from these silicon NPs and observe an 86% capacity retention over 100 cycles at a rate of C/5, with an initial silicon specific capacity of 2600 mAh/g. We expose the same Si NPs to water that completely oxidizes these small-diameter NPs to SiO 2 and find that the SiO 2 NPs in the same electrode configuration exhibit no obvious lithium alloying capacity in the electrochemical potential range of lithium silicide alloy formation. As this result stands in contrast to existing literature, we provide a discussion on the origin of the discrepancies.

25 ENERGY STORAGE↗
DOE OSTI2020

Effects of Extended Aqueous Processing on Structure, Chemistry, and Performance of Polycrystalline LiNi x Mn y Co z O 2 Cathode Powders

The prospect of aqueous processing of LiNi x Mn y Co z O 2 (NMC) cathodes has significant appeal to battery manufacturers for the reduction in materials cost, toxicological risk, and environmental impact compared to conventional N -methyl-2-pyrrolidone (NMP)-based processing. However, the effects of aqueous processing of NMC powders at industrial timescales are not well studied, with prior studies mostly focusing on relatively brief water washing processes. Here, we investigate the bulk and surface impacts of extended aqueous processing of polycrystalline NMC powders with different compositions. We demonstrate that at timescales of several hours, polycrystalline NMC is susceptible to intergranular fracture, with the severity of fracture scaling with the NMC nickel content. While bulk crystallinity and composition are unchanged, surface sensitive techniques such as X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) indicate that the exposure of water leads to a level of delithiation, nickel reduction, and reconstruction from the layered to rock-salt structure at the surface of individual grains. Dynamic single NMC microparticle compression testing suggests that the resulting mechanical stresses weaken the integrity of the polycrystalline particle and increases susceptibility of intergranular fracture. The initially degraded surfaces along with the increased surface area lead to faster capacity fade and impedance growth during electrochemical cycling. From this work, it is demonstrated that NMC powders require surface or grain boundary modifications to make industrial-scale aqueous cathode processing viable, especially for next-generation nickel-rich NMC chemistries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Conversion of Waste PET Plastic to Aramid Fiber

A three-step synthesis was used to convert waste polyethylene terephthalate (PET) into the high value polymer, poly-para-phenylene terephthalamide (PPTA), used in the production of high strength aramid fiber, such as Kevlar. Improvements to the polymerization reaction by addition of calcium chloride to the solvent, N-methyl-2-pyrrolidone (NMP), and rigorous anhydrous conditions enabled the production of a PET-derived PPTA with a 4.15 dL/g inherent viscosity in sulfuric acid that is amenable to fiber spinning. PPTA fibers were spun using a wet spinning apparatus under varied process parameters to assess their impact on fiber surface morphology, diameter, and the mechanical properties of the fibers. Select fibers were subjected to a post-spinning heat treatment at 150 °C , which improved the tensile strength and modulus by 100% and 30%, respectively, relative to the as-spun fibers. Techno-economic and life cycle analyses were conducted to evaluate the economic feasibility and the life-cycle greenhouse gases (GHG) emissions of the approach. In conclusion, the results suggest the potential for up to a 30% cost reduction, and comparable GHG emissions against conventional petroleum-based processes.

Lifecycle Analysis↗
DOE OSTI2020

Crystal Growth, Single Crystal Structure, and Biological Activity of Thiazolo-Pyridine Dicarboxylic Acid Derivatives

Four novel TPDCA derivatives were prepared via a supersaturation method combining TPDCA with water, N-methyl-2-pyrrolidone (NMP), Na(PO 2 H 2 ), and ammonia solution: 2(C 9 H 7 NO 5 S)H 2 O (1), (C 9 H 7 NO 5 S)C 5 H 9 NO (2), (C 9 H 7 NO 5 S)Na(PO 2 H 2 ) (3), and (C 9 H 5 NO 5 S)(NH 4 )2(H 2 O) (4). Their crystal structures were determined by single-crystal X-ray diffraction. Compounds (1) and (2) crystallize in the monoclinic space groups P2 1 and P2 1 /c, respectively, whereas compounds (3) and (4) crystallize in the triclinic space group P1 - . Weak and moderate hydrogen bonds were detected in the four compounds. In the biological tests, (1) and (3) exhibited significant antibacterial activity against Escherichia coli and Staphylococcus aureus; in addition, (1) was cytotoxic against leukemia HL-60 cells with the IC 50 value of 158.5 ± 12.5 μM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Microwave-Based Synthesis of Functional Morphological Variants and Carbon Nanotube-Based Composites of VS 4 for Electrochemical Applications

A novel facile, fast, and efficient microwave-assisted method was developed to synthesize a number of diverse nanostructured motifs (ranging from nanorods to nanoflowers) of VS 4 along with its associated composite heterostructures, VS 4 /multi-walled carbon nanotube (MWNT; i.e., multi-walled carbon nanotubes). Specifically, we have probed and correlated the effects of a number of specific experimental variables, including primarily precursor, solvent, temperature, and time. We noted that nanorods formed more readily with VO(acac) 2 as the vanadium precursor and n-methyl-2-pyrrolidone (NMP) as a polar reaction solvent. By contrast, we determined that hierarchical three-dimensional (3D) nanoflower-like assemblies, ranging in size from 100 to 200 nm in average diameter, could be controllably synthesized by using Na 3 VO 4 as the vanadium precursor and an aqueous water: polar solvent mixture as the reaction medium. We also observed that VS 4 disintegrates, when in the presence of either air, solution, or a combination of these environments, and established that the extent of VS4 nanorod decomposition could be almost fully prevented by storage under nitrogen. From an application’s perspective, our VS 4 is electrochemically active and shows behavior, consistent with the literature. In particular, as compared with pristine VS 4 nanorods alone, we observed enhanced electrochemical activity with (i) 3D hierarchical flower-like motifs, (ii) unique necklace-like VS 4 nanorod–MWNT composites, and (iii) samples in which as-prepared VS4 nanorods had been annealed. Moreover, we found that the rational application of specific physical and chemical processing treatments, such as (i) thermal annealing to improve crystallinity, (ii) the addition of MWNTs to form conductive composites, and (iii) the evolution of morphology from one-dimensional (1D) nanorods to more complex 3D nanoflowers, was favorable to the resulting electrochemical performance with respect to increasing stability and reversibility.

25 ENERGY STORAGE↗
DOE OSTI2025

Investigating the effect of screen-printed structured graphite electrodes with low tortuosity for high-capacity and fast-charging lithium-ion batteries

A flexible screen-printed graphite electrode was fabricated as an anode for developing fast-charging lithium-ion batteries with low tortuosity. A homogenous anode ink was prepared by mixing graphite as the active material, carbon black (C45) as the conductive additive, and polyvinylidene fluoride (PVDF) as the binder in N-Methyl-2-pyrrolidone (NMP) solvent. The ink was deposited on a flexible copper foil via a stainless-steel screen consisting of an array of pores, that act as secondary pore networks (SPNs), using the screen-printing process. Lithium-ion battery half-cells were assembled using the printed graphite anode, lithium metal foil as the counter electrode, and 1.2 M lithium hexafluorophosphate (LiPF 6 ) in ethyl carbonate: ethyl methyl carbonate (EC: EMC = 3:7) as the electrolyte. The effect of SPNs on the cell performance was investigated by performing formation, rate and cycling tests on the assembled cells, at different C-rates. It was observed that the cells consisting of SPNs with a pore size of 100 μm and edge-to-edge distance of 100 μm between the pores exhibited significantly higher specific capacities of 168 and 129 mAh/g when compared to reference cells without SPNs, which had capacities of 120 and 85 mAh/g, at high C-rates of 4 C and 6 C, respectively. The cells with SPNs also demonstrated excellent cycling performance with ~ 95% capacity retention after 100 cycles at 2 C.

Fast charging lithium-ion battery↗