SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Apertures and stops located at conjugate points in receiver optics reduce noise caused by scattered light. They are placed as real, inverse images of each other, so only light from sample volume reaches detector. Noise suppression technique increases signal to noise ratio on order of 15 dB.
An experimental program to reduce aircraft jet turbulence noise investigated the interaction of small auxiliary jets with a larger main jet. Significant reductions in the far field jet noise were obtained over a range of auxiliary jet pressures and flow rates when used in conjunction with an acoustically lined ejector. While the concept is similar to that of conventional ejector suppressors that use mechanical mixing devices, the present approach should improve thrust and lead to lower weight and less complex noise suppression systems since no hardware needs to be located in the main jet flow. A variety of auxiliary jet and ejector configurations and operating conditions were studied. The best conditions tested produced peak to peak noise reductions ranging from 11 to 16 dB, depending on measurement angle, for auxiliary jet mass flows that were 6.6% of the main jet flow with ejectors that were 8 times the main jet diameter in length. Much larger reductions in noise were found at the original peak frequencies of the unsuppressed jet over a range of far field measurement angles.
The effect of swirling flow on jet noise suppression was experimentally investigated in a relatively small, low-thrust, fan-jet engine. Measurements of acoustic properties of the near and far fields, jet-flow characteristics, and engine thrust were made with and without stationary swirl vanes installed in the primary exhaust nozzle. Preliminary test results indicate that substantial reductions in jet overall sound pressure levels and overall acoustic power were obtained with minimal thrust losses. Based on preliminary analysis, present results, and previous experiments with swirling hot jets, it is predicted that even greater jet noise reductions can be obtained in higher thrust engines, particularly with afterburning, by swirling jet exhaust.
Program for perceived noise levels reduction on ground of turbofan-powered commercial transport by acoustically absorptive lining of ducts
Program for perceived noise levels reduction on ground of turbofan powered commercial transport by acoustically absorptive lining of ducts
A mathematical model containing the essential features embodied in the noise suppression of lined ejectors is presented. Although some simplification of the physics is necessary to render the model mathematically tractable, the current model is the most versatile and technologically advanced at the current time. A system of linearized equations and the boundary conditions governing the sound field are derived starting from the equations of fluid dynamics. A nonreflecting boundary condition is developed. In view of the complex nature of the equations, a parametric study requires the use of numerical techniques and modern computers. A finite element algorithm that solves the differential equations coupled with the boundary condition is then introduced. The numerical method results in a matrix equation with several hundred thousand degrees of freedom that is solved efficiently on a supercomputer. The model is validated by comparing results either with exact solutions or with approximate solutions from other works. In each case, excellent correlations are obtained. The usefulness of the model as an optimization tool and the importance of variable impedance liners as a mechanism for achieving broadband suppression within a lined ejector are demonstrated.
Acoustic treatment was developed for jet engine turbine noise suppression. Acoustic impedance and duct transmission loss measurements were made for various suppression systems. An environmental compatibility study on several material types having suppression characteristics is presented. Two sets of engine hardware were designed and are described along with engine test results which include probe, farfield, near field, and acoustic directional array data. Comparisons of the expected and the measured suppression levels are given as well as a discussion of test results and design techniques.
A device and method is disclosed for suppression of optical noise in an optical spatial filtering system using highly coherent light. In the disclosed embodiment, input photographic film to be processed in the system, and output photographic film to be exposed, are each mounted on lateral translation devices. During application of the coherent light for exposure of the output film, the two translation devices are moved in synchronism by a motor-driven gear and linkage assembly. The ratio of the resulting output film translation to the input film translation is equal to the magnification of the optical data processing system. The noise pattern associated with the lenses and other elements in the optical processing system remains stationary while the image-producing light moves laterally through the pattern with the output film, thus averaging out the noise effect at the output film.
The noise-generating region of a suppressed turbojet exhaust is studied by cross-correlating static pressure fluctuations within the exhaust with far-field sound for Mach numbers up to 0.99, using a 31-tube nozzle having an area ratio of 3.1. Measurements made with an unsuppressed turbojet exhaust having an equivalent area ratio and operating under effectively equal thrust loads serve as the experimental control. Static pressure-level measurements, made with a calibrated high-temperature acoustically damped probe tube, show that noise suppression by multitube nozzles results from reduced turbulence levels. The maximum fluctuating static-pressure level in the unsuppressed turbojet exhaust is typically 5-6 dB higher than static-pressure levels in the suppressed exhaust under conditions of effectively equal static thrust. This suggests that the turbulence intensity in the multitube suppressor flow is reduced in excess of 20% compared with the unsuppressed jet exhaust.
A signal-to-noise ratio dependent adaptive spectral subtraction process eliminates noise from noise-corrupted speech signals. The process first pre-emphasizes the frequency components of the input sound signal which contain the consonant information in human speech. Next, a signal-to-noise ratio is determined and a spectral subtraction proportion adjusted appropriately. After spectral subtraction, low amplitude signals can be squelched. A single microphone is used to obtain both the noise-corrupted speech and the average noise estimate. This is done by determining if the frame of data being sampled is a voiced or unvoiced frame. During unvoiced frames an estimate of the noise is obtained. A running average of the noise is used to approximate the expected value of the noise. Spectral subtraction may be performed on a composite noise-corrupted signal, or upon individual sub-bands of the noise-corrupted signal. Pre-averaging of the input signal's magnitude spectrum over multiple time frames may be performed to reduce musical noise.
Nozzle performance was obtained with cold primary and secondary flows over a range of nozzle pressure ratio from 2 to 31 and corrected secondary-to primary-flow ratio from 0 to 11 percent. Several fixed shroud positions were tested to simulate a translating outer cylindrical shroud to provide data for both supersonic cruise and takeoff configurations. The addition of 14 spokes in the primary nozzle for noise suppression reduced the thrust efficiency 3 percent at supersonic cruise and 4.5 percent at takeoff.
A TF-34 engine with an acoustically treated ground test nacelle was built and tested to determine the feasibility of suppressing fan and core engine noise to the stringent levels required for STOL or short-haul commercial aircraft. The design incorporates wall treatment for the fan and core plus three treated splitter rings in the inlet and two treated splitters in the aft fan duct. Maximum suppression of fan tone noise of 40-45 dB was obtained from both the inlet and aft fan treatment. At rated fan speed, overall noise was reduced by 21 PNdB to a value of 94 PNdB on a 500-foot sideline. The overall noise reduction value was limited by the jet noise floor. Thrust losses due to the acoustic treatment are also discussed.
An adaptive control system based on normalized LMS filters is investigated. The finite impulse response of the nonparametric controller is adaptively estimated using a given reference model. Specifically, the following issues are addressed: The stability of the closed loop system is analyzed and heuristically established. Next, the adaptation process is studied for piecewise constant plant parameters. It is shown that by introducing a variable-gain in the gradient algorithm, a substantial reduction in the LMS adaptation rate can be achieved. Finally, process noise at the plant output generally causes a biased estimate of the controller. By introducing a noise suppression scheme, this bias can be substantially reduced and the response of the adapted system becomes very close to that of the reference model. Extensive computer simulations validate these and demonstrate assertions that the system can rapidly adapt to random jumps in plant parameters.
NASA Grant NAG1-1802, originally submitted in June 1996 as a two-year proposal, was awarded one-year's funding by NASA LaRC for the period 5 Oct., 1996, through 4 Oct., 1997. Because of the inavailability (from IT at NASA ARC) of sufficient supercomputer time in fiscal 1998 to complete the computational goals of the second year of the original proposal (estimated to be at least 400 Cray C-90 CPU hours), those goals have been appropriately amended, and a new proposal has been submitted to LaRC as a follow-on to NAG1-1802. The current report documents the activities and accomplishments on NAG1-1802 during the one-year period from 5 Oct., 1996, through 4 Oct., 1997. NASA Grant NAG1-1802, and its predecessor, NAG1-1772, have been directed toward adapting the numerical tool of Large-Eddy Simulation (LES) to aeroacoustic applications, with particular focus on noise suppression in subsonic round jets. In LES, the filtered Navier-Stokes equations are solved numerically on a relatively coarse computational grid. Residual stresses, generated by scales of motion too small to be resolved on the coarse grid, are modeled. Although most LES incorporate spatial filtering, time-domain filtering affords certain conceptual and computational advantages, particularly for aeroacoustic applications. Consequently, this work has focused on the development of SubGrid-Scale (SGS) models that incorporate time- domain filters. The author is unaware of any previous attempt at purely time-filtered LES; however, Aldama and Dakhoul and Bedford have considered approaches that combine both spatial and temporal filtering. In our view, filtering in both space and time is redundant, because removal of high frequencies effects the removal of small spatial scales and vice versa.
The paper describes the application of techniques based on computational fluid dynamics to the simulation of jet flowfields. A solution code for the Reynolds-averaged Navier-Stokes equations is supplemented by conventional two-equation turbulence models based on the Boussinesq approximation. The axisymmetric SCIPVIS code is enhanced with the PARCH and CRAFT codes to examine plug-jet flowfields and imperfectly expanded axisymmetric free round jets. The sensitivity of shock/boundary layer interactions is observed in simulations of the plug case, and the adaptive gridding in the disk region and turbulence levels generated at the triple point are identified as areas in the Mach case that require improvement. Jet-wave structure in the region beyond the first several shock cells can be predicted, and turbulence modeling can be undertaken with respect to improving compressibility, length scale, vorticity, and energy budget. The mean flow structure of imperfectly expanded jets can be studied to develop related noise suppression concepts for the High-Speed Civilian Transport (HSCT).
The acoustic fields and transmission losses produced in semi-infinite circular ducts with peripherally segmented liners are analyzed using a series expansion of hard-wall duct modes. The coefficients of the series are computed using Galerkin's method. Unlike finite element approaches, this analysis includes the effects of realistic sources and the number of peripheral strips need not be small. It is shown that peripherally segmented liners redistribute the acoustic energy in waves composed of only a single circumferential mode at the source into other waves which contain a multitude of circumferential modes in the lined section. The accuracy of eigenfunctions computed from the analysis was observed to increase as either the frequency or radial mode order increased. The transmission losses were found to be accurate at frequencies above the cut-on value of the first-order radial mode in a hard-wall duct. The results show that for plane wave sources, peripherally segmented liners may attenuate as much sound as an optimized uniform liner at the optimal point while giving more noise suppression at most other frequencies.
Attenuation properties of three treated fan inlets were evaluated in the NASA-Lewis Anechoic Wind Tunnel using a subsonic tip speed, 50.8 cm-diameter fan. Tunnel flow simulated the inflow clean-up effect on source noise observed in flight and allowed observation of the blade passage frequency tone cut-off phenomenon. Acoustic data consisted of isolated inlet noise measured in the far field at two positions and with traverses at four frequencies. Averaged attenuation properties showed relative agreement of the inlets with their design intent; however, tunnel flow significantly affected the attenuation spectra. With no tunnel flow the strong blade passage tone was more highly attenuated than the adjacent broadband noise. With tunnel flow, when cut-off was observed, the attenuation at the tone frequency was comparable to that for broadband noise. Tunnel flow increased by several dB the maximum attenuation occurring at midfrequencies of the attenuation spectra. The combined effect of tunnel flow on attenuation and source noise resulted in suppressed fan noise levels throughout the spectra. Tunnel flow caused some substantial directivity variations that are interpreted as acoustic mode changes, with tunnel flow generally reducing the proportion of modes near cut-off.
Comparator continuously and automatically adjusts noise immunity period. High-gain amplifier used in conjunction with multivibrator 4 to provide clear pulse to multivibrator 1 at first negative-going zero crossing of input signal. Once multivibrator 1 cleared, output goes to zero volts and not retriggered until next time positive input exceeds reference level. Since input signal noise at zero crossing does not exceed reference level, no effect on multivibrator 1 operation. Circuit fabricated using standard solid-state operational amplifiers, multivibrators, OR gates, and passive elements.