Search NASA⌕ Search

SEARCH · Search NASA

Results for “optimization platform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Microgravity vibration isolation: An optimal control law for the one-dimensional case

Certain experiments contemplated for space platforms must be isolated from the accelerations of the platforms. An optimal active control is developed for microgravity vibration isolation, using constant state feedback gains (identical to those obtained from the Linear Quadratic Regulator (LQR) approach) along with constant feedforward (preview) gains. The quadratic cost function for this control algorithm effectively weights external accelerations of the platform disturbances by a factor proportional to (1/omega)(exp 4). Low frequency accelerations (less than 50 Hz) are attenuated by greater than two orders of magnitude. The control relies on the absolute position and velocity feedback of the experiment and the absolute position and velocity feedforward of the platform, and generally derives the stability robustness characteristics guaranteed by the LQR approach to optimality. The method as derived is extendable to the case in which only the relative positions and velocities and the absolute accelerations of the experiment and space platform are available.

Hampton, R. D.↗
NASA NTRS1994

Evaluation of sensor placement algorithms for on-orbit identification of space platforms

Anticipating the construction of the international space station, on-orbit modal identification of space platforms through optimally placed accelerometers is an area of recent activity. Unwanted vibrations in the platform could affect the results of experiments which are planned. Therefore, it is important that sensors (accelerometers) be strategically placed to identify the amount and extent of these unwanted vibrations, and to validate the mathematical models used to predict the loads and dynamic response. Due to cost, installation, and data management issues, only a limited number of sensors will be available for placement. This work evaluates and compares four representative sensor placement algorithms for modal identification. Most of the sensor placement work to date has employed only numerical simulations for comparison. This work uses experimental data from a fully-instrumented truss structure which was one of a series of structures designed for research in dynamic scale model ground testing of large space structures at NASA Langley Research Center. Results from this comparison show that for this cantilevered structure, the algorithm based on Guyan reduction is rated slightly better than that based on Effective Independence.

Glassburn, Robin S.↗
NASA NTRSDate not supplied

Optimization of a Solver for Computational Materials and Structures Problems on NVIDIA Volta and AMD Instinct GPUs

The Scalable Implementation of Finite Elements by NASA (ScIFEN) is a software package developed to solve complex computational materials and structures problems using the finite element method (FEM). In this paper, we describe optimization techniques to speed up the linear solver computation that occurs within the ScIFEN application. We consider GPUs from two different vendors, NVIDIA and AMD as our target platforms for optimization and highlight differences in performance and optimization techniques. The NVIDIA GPU Volta V100 is used in the Summit system deployed at Oak Ridge National Laboratory, and the new exascale system, Frontier, will be using AMD Radeon Instinct GPU. We evaluated the performance of various optimization techniques on test matrices, ranging in size from100K to 4M, that are representative of ScIFEN applications. The linear solver computation is memory-bound on both GPUs. Our experiments show that on the NVIDIA GPU we obtained up to79%of the theoretical peak bandwidth, while the AMD GPU achieved 59%. Overall, the NVIDIA V100 GPU outperforms the AMD MI 25 GPU1. We observed an overall speedup of up to37X on an NVIDIA V100 compared to an Intel Skylake 12-coremachine. The solver for a 4M degree of freedom system took under 2.5 seconds.

Mohammad Zubair↗
NASA NTRS2018

Implementation of Topology Optimization Using OpenMDAO

Topology optimization is one of the widely known branches among the structural optimization, and it distinguishes itself by a large design domain and versatility. It can determine the optimal design out of an infinite number of configurations, thereby drawing interest from both industry and academia with regards to its applicability to additive manufacturing. However, its implementation is often a daunting task for engineers in practice. One of the issues is the programming effort required whenever the implementation requires any changes, ranging from subtle tweaks to drastic changes in the problem definition, and the derivative computation must be correspondingly updated after any change. The implementation, therefore, is not only time-consuming but also repetitive and susceptible to human-induced errors. In this regard, topology optimization implementations stand to benefit from reusability, ease of restructuring, and modularity. In this work, we propose OpenMDAO, a computational framework for multidisciplinary design optimization (MDO), as a generic platform for topology optimization. Two widely used topology optimization techniquesâ€"density-based and level-setâ€"are implemented as a demonstration. These techniques are implemented in a decomposed manner, with the aid of the modular architecture of OpenMDAO as well as state-of-the-art numerical methods. Variations on the density-based topology optimization approach are shown to demonstrate the modularity and automation for derivative computation that OpenMDAO provides.

Chung, Hayoung↗
NASA NTRSDate not supplied

QuAIL Tools for Benchmarking, Analysis and Quantum Algorithm Development

HybridQ and PySA are open-source tools developed by NASA to support benchmarking, analysis and quantum algorithm development in areas such as simulation, optimization and machine learning. These tools leverage classical hardware acceleration via high-performance computing CPU and GPU architectures and support high-performance computing. HybridQ is a highly extensible platform designed to provide a common framework to integrate multiple state-of-the-art techniques to simulate large scale quantum circuits. PySA is an extensible platform to optimize a classical cost function. We provide an outline of each of these open-source tools and highlight projects using each of these tools in contexts of simulation, optimization and machine learning.

Quantum Computing↗
NASA NTRS2023

Easy, Scalable Subsetting of GEDI Point Clouds

The GEDI Subsetter, a Python tool developed for NASA’s Multi-mission Algorithm and Analysis Platform (MAAP), optimizes the accessibility and visualization of GEDI point clouds by enabling users to efficiently subset data in a convenient, scalable manner. Complex science data often requires users to learn new software skills and handle many large files. Handling and cleaning large data sets is tedious and error-prone. These challenges significantly impede analysis. One of the goals of NASA's MAAP is to provide a platform that lowers the barrier to conducting research and analysis at scale. When a group of MAAP users wanted to conduct above-ground biomass estimation using GEDI data, we found that their existing workflow for leveraging GEDI data suffered from the barriers mentioned above. Furthermore, their workflow did not scale easily beyond a small number of granules. We found that existing tools related to GEDI data retrieval and subsetting were too limiting, so the GEDI Subsetter was written to support MAAP users’ needs. Being able to run many subsetting jobs simultaneously in the MAAP, and parallelizing the code itself, has led to significant speed improvements in obtaining relevant data, reducing subsetting time from hours to minutes. MAAP users can now more quickly and easily obtain only the data relevant to their research, by choosing which GEDI collection they want to work with (L1A, L2A, L2B, or L4A), and how they want to subset it, by specifying an area of interest, a temporal range, and relevant attributes. This has significantly reduced the feedback loop for users, allowing them to much more quickly subset GEDI data and begin their analysis. Although the GEDI Subsetter originally targeted users of the MAAP, it is generalized such that it can also be used outside of the MAAP and includes a command-line interface for convenience. Furthermore, with minor modifications, it should be possible to use it with non-GEDI data as the general pattern should be applicable to other sparse/track-based sensors.

Charles Daniels↗
NASA NTRSDate not supplied

BioNutrients-2: Improvements to the BioNutrients-1 Nutrient Production System

The BioNutrients (BN) project aims to develop an on-demand nutrient production system capable of rapid and safe delivery of multiple nutrients in a single-use production pack for long-duration missions. The general concept of this system will be to develop an edible engineered microorganism capable of surviving during long-term storage, revival and growth of that microorganism for product production, and delivery of precise quantities of nutrients for human consumption. BN-1 is a five-year flight project currently on the International Space Station (ISS). It is testing the long-term storage of various microorganisms for the biomanufacturing of space relevant compounds and to validate the performance of the first generation (Gen-1) of production packs. The BN-2 project is a continuation of the BN-1 flight project and intends to expand the projects overall scope by introducing novel products, broadening the range of microbial food sources, and improving previously designed hardware from the BN-1 project. We are in the process of optimizing our platform biomanufacturing technology for in situ production of yogurt and kefir on the ISS. BN-2 will test the efficacy of this technology for future delivery of probiotic organisms which can be engineered to produce additional nutritional supplements (consumption by the crew is not planned in this project). Furthermore, to improve the feasibility of this technology for mission use we have transitioned from a hard-shell pack to a Gen-2, fluorinated ethylene propylene (FEP) bag. The single-use FEP bioreactor will facilitate growth of known organisms and ensure a contaminant free environment, while reducing mass and volume. These bioreactors will be employed for production of additional space relevant products in the BN-2 project. On-orbit testing of Gen-2 production packs will be necessary for future iterations, in order to optimize bag design and product production for eventual flight use by the crew.

BioNutrients↗
NASA NTRS2011

Challenges at Petascale for Pseudo-Spectral Methods on Spheres (A Last Hurrah?)

Conclusions: a) Proper software abstractions should enable rapid-exploration of platform-specific optimizations/ tradeoffs. b) Pseudo-spectra! methods are marginally viable for at least some classes of petascaie problems. i.e., GPU based machine with good bisection would be best. c) Scalability at exascale is possible, but the necessary resolution will make algorithm prohibitively expensive. Efficient implementations of realistic global transposes are mtricate and tedious in MPI. PS at petascaie requires exploration of a variety of strategies for spreading local and remote communic3tions. PGAS allows far simpler implementation and thus rapid exploration of variants.

Clune, Thomas↗
NASA NTRS2012

Mercury Atomic Frequency Standards for Space Based Navigation and Timekeeping

A low power Mercury Atomic Frequency Standard (MAFS) has been developed and demonstrated on the path towards future space clock applications. A self contained mercury ion breadboard clock: emulating flight clock interfaces, steering a USO local oscillator, and consuming approx 40 Watts has been operating at JPL for more than a year. This complete, modular ion clock instrument demonstrates that key GNSS size, weight, and power (SWaP) requirements can be achieved while still maintaining short and long term performance demonstrated in previous ground ion clocks. The MAFS breadboard serves as a flexible platform for optimizing further space clock development and guides engineering model design trades towards fabrication of an ion clock for space flight.

Global Positioning Systems (GPS)↗
NASA NTRS2014

Demonstration of Prognostics-Enabled Decision Making Algorithms on a Hardware Mobile Robot Test Platform

Prognostics-enabled Decision Making (PDM) is an emerging research area that aims to integrate prognostic health information and knowledge about the future operating conditions into the process of selecting subsequent actions for the system. Previous work developing and testing PDM algorithms has been done in simulation; this paper describes the effort leading to a successful demonstration of PDM algorithms on a hardware mobile robot platform. The hardware platform, based on the K11 planetary rover prototype, was modified to allow injection of selected fault modes related to the rover’s electrical power subsystem. The PDM algorithms were adapted to the hardware platform, including development of a software module framework, a new route planner, and modifications to increase the algorithms’ robustness to sensor noise and system timing issues. A set of test scenarios was chosen to demonstrate the algorithms’ capabilities. The modifications to run with a hardware platform, the test scenarios, and the test results are described in detail. The results show a successful use of PDM algorithms on a hardware test platform to optimize mission planning in the presence of electrical system faults.

Prognosis↗
NASA NTRS2023

Design Status of Gondola for High-Altitude Planetary Science (GHAPS)

The Gondola for High-Altitude Planetary Science (GHAPS) project was initiated to develop a balloon platform to meet planetary science goals and objectives as outlined in the NASA decadal survey. GHAPS is a first-generation reusable platform design optimized for multiple long-duration flights and planetary science. The gondola design was intended to accommodate infrared (IR) and ultraviolet/visible (UV-Vis) observations, supporting detection of water and carbon dioxide and allowing for long-duration flights to enable time-based studies. It was anticipated that the GHAPS gondola design would evolve over time with changing science demands. This report describes the as-designed configuration and capabilities of the GHAPS gondola.

Planetary Science↗
NASA NTRSDate not supplied

Homogenization of Satellite Based Hyperspectral Infrared Sounder Data To Build Long Term Climate Record

Building long term climate record using data from multiple hyperspectral Infrared (IR)sounders requires the homogenization of different data record to ensure the consistency andcontinuity. Such a requirement comes from two perspectives: 1) the need to adjust theoverlapping measurements of different sounders to ensure the radiometric consistency in thespectral radiance domain; 2) the need for a rigorously defined scheme to ensure the radiometricconsistency being transferred to the essential climate variables derived from the radiance record.We develop a solution that uses a spectral fingerprinting scheme to derive anomalies of keyclimate variables from long term spectral radiance data record constructed using both AIRS andCrIS observations aboard AQUA, SNPP and JPSS satellites. The fingerprinting scheme usescommon radiative kernels for all sounder measurements and therefore effectively avoids thealgorithm introduced inconsistency in retrieved geophysical variables. Our approach uses aunified sampling scheme to match AIRS and CrIS observations in both spectral and spatial-temporal domain, facilitating the intercomparison of spectral radiances from different sensors(platforms). The optimized liner inversion scheme allows the direct quantification and thereforethe adjustment for the impact on the derived climate anomalies imposed by potential radiometricinconsistency between the overlapping measurements. Such a scheme also enables the low-latency data processing of long term hyperspectral sounder data records. This paper provides a detailed introduction of the spectral fingerprinting methodology.Also introduced here is the climate fingerprinting Sounder Product (ClimFiSP) developed basedon the fingerprinting methodology. ClimFiSP products include the space-time averagedproperties of key climate variables that are derived from the long-term, space-time averagedradiances from AQUA-AIRS, SNPP-CrIS, and JPSS1-CrIS. ClimFiSP will be available to usersthrough NASA'sGoddard Earth Sciences Data and Information Services Center (GES DISC).

Wan Wu↗
NASA NTRS2018

Meander-Like Shape Optimization of the Stator-Rotor Platform Cavity

Recent progress in additive manufacturing has enabled opportunities to explore novel stator rim geometries which can be implemented to improve cooling strategies in turbomachinery. This paper presents a simplified stationary geometry optimization strategy to produce enhanced stator-rotor cavity sealing and highlights main driving mechanisms.The stator and rotor rims were designed using a design strategy based on inspiration from the meandering of rivers. A minimum thickness of 2 millimeters was maintained throughout the cavity to ensure a practical implementation. The computational domain comprised of the stator outlet, hub disk leakage cavity, and rotor platform was meshed using NUMECA Int. package, Hexpress. The numerical analysis required 3D Unsteady Reynolds Average Navier-Stokes to replicate vorticial structures using Ansys Fluent. The operating conditions were representative of engine-like conditions, exploring a wide range of mass flow ratios from 1 to 3 percent. The optimization yielded designs that provide 30 percent reduction in rear platform temperature while minimizing coolant mass flow. The applicability of the design was compared against 3D sector in both stationary and in rotation.

Shape Optimization↗
NASA NTRS2017

Semi-Supervised Learning of Lift Optimization of Multi-Element Three-Segment Variable Camber Airfoil

This chapter describes a new intelligent platform for learning optimal designs of morphing wings based on Variable Camber Continuous Trailing Edge Flaps (VCCTEF) in conjunction with a leading edge flap called the Variable Camber Krueger (VCK). The new platform consists of a Computational Fluid Dynamics (CFD) methodology coupled with a semi-supervised learning methodology. The CFD component of the intelligent platform comprises of a full Navier-Stokes solution capability (NASA OVERFLOW solver with Spalart-Allmaras turbulence model) that computes flow over a tri-element inboard NASA Generic Transport Model (GTM) wing section. Various VCCTEF/VCK settings and configurations were considered to explore optimal design for high-lift flight during take-off and landing. To determine globally optimal design of such a system, an extremely large set of CFD simulations is needed. This is not feasible to achieve in practice. To alleviate this problem, a recourse was taken to a semi-supervised learning (SSL) methodology, which is based on manifold regularization techniques. A reasonable space of CFD solutions was populated and then the SSL methodology was used to fit this manifold in its entirety, including the gaps in the manifold where there were no CFD solutions available. The SSL methodology in conjunction with an elastodynamic solver (FiDDLE) was demonstrated in an earlier study involving structural health monitoring. These CFD-SSL methodologies define the new intelligent platform that forms the basis for our search for optimal design of wings. Although the present platform can be used in various other design and operational problems in engineering, this chapter focuses on the high-lift study of the VCK-VCCTEF system. Top few candidate design configurations were identified by solving the CFD problem in a small subset of the design space. The SSL component was trained on the design space, and was then used in a predictive mode to populate a selected set of test points outside of the given design space. The new design test space thus populated was evaluated by using the CFD component by determining the error between the SSL predictions and the true (CFD) solutions, which was found to be small. This demonstrates the proposed CFD-SSL methodologies for isolating the best design of the VCK-VCCTEF system, and it holds promise for quantitatively identifying best designs of flight systems, in general.

Intelligent Systems↗
NASA NTRSDate not supplied

BioNutrients-2: Improvements to the BioNutrients-1 Nutrient Production System

The BioNutrients (BN) project aims to develop an on-demand biological production system capable of rapid and safe delivery of multiple nutrients in single-use production packs for long-duration missions. The general concept of this system is to develop edible engineered microorganisms that produce nutrients for human consumption following long-term storage, revival, and growth. BN-1 is a five-year flight project currently on the International Space Station (ISS). It is testing the long-term storage of various microorganisms for the biomanufacturing of space-relevant compounds and validating the performance of the first generation of production packs. The BN-2 project expands the BN-1 flight project scope by introducing novel products, broadening the range of microbial food sources, and improving upon production pack hardware. We are optimizing the biomanufacturing platform for in situ production of yogurt and kefir on the ISS. BN-2 also will test engineered microorganisms, including a probiotic strain, to produce carotenoids or follistatin. To improve the feasibility of this technology for mission use, we transitioned from a hard-shell pack to a second-generation fluorinated ethylene propylene (FEP) bag. The single-use FEP bioreactor facilitates growth of target organisms in a contaminant free environment, while reducing mass and volume compared to the BN-1 hardware. These bioreactors will be employed for production of additional space-relevant products in the BN-2 project. On-orbit testing of FEP production packs will enable optimization of the platform for eventual flight use by the crew.

Natalie Ball↗
NASA NTRS1986

The development of optimal control laws for orbiting tethered platform systems

A mathematical model of the open and closed loop in orbit plane dynamics of a space platform-tethered-subsatellite system is developed. The system consists of a rigid platform from which an (assumed massless) tether is deploying (retrieving) a subsatellite from an attachment point which is, in general, offset from the platform's mass center. A Langrangian formulation yields equations describing platform pitch, subsatellite tetherline swing, and varying tether length motions. These equations are linearized about the nominal station keeping motion. Control can be provided by both modulation of the tether tension level and by a momentum type platform-mounted device; system controllability depends on the presence of both control inputs. Stability criteria are developed in terms of the control law gains, the platform inertia ratio, and tether offset parameter. Control law gains are obtained based on linear quadratic regulator techniques. Typical transient responses of both the state and required control effort are presented.

Bainum, P. M.↗
NASA NTRS1986

The development of optimal control laws for orbiting tethered platform systems

A mathematical model of the open and closed loop in-orbit plane dynamics of a space platform-tethered-subsatellite system is developed. The system consists of a rigid platform from which an (assumed massless) tether is deploying (retrieving) a subsatellite from an attachment point which is, in general, offset from the platform's mass center. A Lagrangian formulation yields equations describing platform pitch, subsatellite tether-line swing, and varying tether length motions. These equations are linearized about the nominal station keeping motion. Control can be provided by both modulation of the tether tension level and by a momentum type platform-mounted device; system controllability depends on the presence of both control inputs. Stability criteria are developed in terms of the control law gains, the platform inertia ratio, and tether offset parameter. Control law gains are obtained based on linear quadratic regulator techniques. Typical transient responses of both the state and required control effort are presented.

Bainum, P. M.↗
NASA NTRS2016

High-Performance Reaction Wheel Optimization for Fine-Pointing Space Platforms: Minimizing Induced Vibration Effects on Jitter Performance plus Lessons Learned from Hubble Space Telescope for Current and Future Spacecraft Applications

The Hubble Space Telescope (HST) applies large-diameter optics (2.5-m primary mirror) for diffraction-limited resolution spanning an extended wavelength range (approx. 100-2500 nm). Its Pointing Control System (PCS) Reaction Wheel Assemblies (RWAs), in the Support Systems Module (SSM), acquired an unprecedented set of high-sensitivity Induced Vibration (IV) data for 5 flight-certified RWAs: dwelling at set rotation rates. Focused on 4 key ratios, force and moment harmonic values (in 3 local principal directions) are extracted in the RWA operating range (0-3000 RPM). The IV test data, obtained under ambient lab conditions, are investigated in detail, evaluated, compiled, and curve-fitted; variational trends, core causes, and unforeseen anomalies are addressed. In aggregate, these values constitute a statistically-valid basis to quantify ground test-to-test variations and facilitate extrapolations to on-orbit conditions. Accumulated knowledge of bearing-rotor vibrational sources, corresponding harmonic contributions, and salient elements of IV key variability factors are discussed. An evolved methodology is presented for absolute assessments and relative comparisons of macro-level IV signal magnitude due to micro-level construction-assembly geometric details/imperfections stemming from both electrical drive and primary bearing design parameters. Based upon studies of same-size/similar-design momentum wheels' IV changes, upper estimates due to transitions from ground tests to orbital conditions are derived. Recommended HST RWA choices are discussed relative to system optimization/tradeoffs of Line-Of-Sight (LOS) vector-pointing focal-plane error driven by higher IV transmissibilities through low-damped structural dynamics that stimulate optical elements. Unique analytical disturbance results for orbital HST accelerations are described applicable to microgravity efforts. Conclusions, lessons learned, historical context/insights, and perspectives on future applications are given; these previously unpublished data and findings represents a valuable resource for fine-pointing spacecraft or space-based platforms using RWAs, Control Moment Gyros (CMGs), Momentum Wheels, or other ball-bearing-based rotational units.

Hasha, Martin D.↗