Search NASA⌕ Search

SEARCH · Search NASA

Results for “oscillatory power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Numerical thermal analyses of heat exchangers for the stirling engine application

The Regenerator, Cooler and Heater for the NASA Space Power Research Engine (SPRE) have been analyzed in detail for laminar, incompressible and oscillatory flow conditions. Each component has been analyzed independently and in detail with the regenerator being modeled as two-parallel-plates channel with a solid wall. The ends of the channel are exposed to two reservoir maintained at different temperature thus providing an axial temperature gradient along the channel. The cooler and heater components have been modeled as circular pipes with isothermal walls. Two different types of thermal boundary conditions have been investigated for the cooler and heater, namely, symmetric and asymmetric temperature inflow. In symmetric temperature inflow the flow enters the channel with the same temperature in throughout the velocity cycle whereas, in asymmetric temperature inflow the flow enters with a different temperature in each half cycle. The study was conducted over a wide range of Maximum Reynolds number (RE(max) varying from 75 to 60000, Valensi number (Va) from 2.5 to 800, and relative amplitude of fluid displacement (A(sub r) from 0.357 to 1.34. A two dimensional Finite volume method based on the SIMPLE algorithm was used to solve the governing partial differential equations. Post processing programs were developed to effectively describe the heat transfer mechanism under oscillatory flows. The computer code was validated by comparing with existing analytical solutions for oscillating flows. The thermal field have been studied with the help of temperature contour and three dimensional plots. The instantaneous friction factor, wall heat flux and heat transfer coefficient have been examined. It has been concluded that in general, the frictional factor and heat transfer coefficient are higher under oscillatory flow conditions when the Valensi number is high. Also, the thermal efficiency decreases for lower A(r) values. Further, the usual steady state definition for the heat transfer coefficient does not seem to be valid.

Kannapareddy, Mohan Raj↗
NASA NTRS2004

Quantification of Inlet Impedance Concept and a Study of the Rayleigh Formula for Noise Radiation from Ducted Fan Engines

This paper addresses two aspects of duct propagation and radiation which can contribute to more efficient fan noise predictions. First, we assess the effectiveness of Rayleigh's formula as a ducted fan noise prediction tool. This classical result which predicts the sound produced by a piston in a flanged duct is expanded to include the uniform axial inflow case. Radiation patterns using Rayleigh's formula with single radial mode input are compared to those obtained from the more precise ducted fan noise prediction code TBIEM3D. Agreement between the two methods is excellent in the peak noise regions both forward and aft. Next, we use TBIEM3D to calculate generalized radiation impedances and power transmission coefficients. These quantities are computed for a wide range of operating parameters. Results were obtained for higher Mach numbers, frequencies, and circumferential mode orders than have been previously published. Viewed as functions of frequency, calculated trends in lower order inlet impedances and power transmission coefficients are in agreement with known results. The relationships are more oscillatory for higher order modes and higher Mach numbers.

Posey, Joe W.↗
NASA NTRS1974

Oscillatory supersonic kernel function method for interfering surfaces

In the method presented in this paper, a collocation technique is used with the nonplanar supersonic kernel function to solve multiple lifting surface problems with interference in steady or oscillatory flow. The pressure functions used are based on conical flow theory solutions and provide faster solution convergence than is possible with conventional functions. In the application of the nonplanar supersonic kernel function, an improper integral of a 3/2 power singularity along the Mach hyperbola is described and treated. The method is compared with other theories and experiment for two wing-tail configurations in steady and oscillatory flow.

Cunningham, A. M., Jr.↗
NASA NTRS1999

Surface Tension Driven Convection Experiment-2 (STDCE-2)

Thermocapillary flows are known to become oscillatory (time-periodic), but how and when they become oscillatory in containers of unit-order aspect ratio are not yet fully understood. The present work is a part of our continuous effort to obtain a better understanding of the phenomenon. Thermocapillary flow experiments in normal gravity are limited to a narrow parametric range in order to minimize gravity and buoyancy effects, which is an important reason for our lack of full understanding of the oscillation phenomenon. One important unanswered question is what role, if any, free surface deformation plays in the oscillation mechanism. For that reason we performed thermocapillary flow experiments, called the Surface Tension Driven Convection Experiment-2 (STDCE-2), aboard the USML-2 Spacelab in 1995. The main objectives of the experiments were to investigate oscillatory thermocapillary flows in microgravity and to clarify the importance of free surface deformation in such flows. Steady and oscillatory thermocapillary flows were generated in cylindrical containers by employing two heating modes. A CO2 laser with adjustable power and beam diameter was used in the Constant Flux (CF) configuration to heat the free surface. The other configuration investigated in STDCE-2 was the Constant Temperature (CT) configuration in which a submerged cylindrical cartridge heater placed at the symmetry (axial) axis of the test container heated the fluid. Both heating modes cause non-uniform temperature distributions on the free surface, which generates thermocapillary flow. The flow field was investigated by flow visualization, and the temperature field was measured by thermistors and an infrared imager. The free surface shape and motion were measured by a Ronchi system. The hardware performed well and we were able to conduct more tests than originally planned. From the successful experiments a large amount of data was acquired. The analysis of the data is now nearly complete. Some important results are presented and discussed herein.

Masud, J.↗
NASA NTRS1980

Preliminary design study of a higher harmonic blade feathering control system

The feasibility to incorporate an active higher harmonic control (HHC) system on an OH-6A rotorcraft was demonstrated. The introduction of continuously modulated low amplitude 4P feathering showed potential for reducing rotor transmitted oscillatory loads. The design implementation of this system on a baseline OH-6A required generation of a hydraulic power system, control actuator placement and design integration of an electronic subsystem comprised of an electronic control unit (ECU) and digital microcomputer. Various placements of the HHC actuators in the primary control system are evaluated. Assembly drawings of the actuator concepts and control rigging are presented. The advantages of generating both hydraulic power and 4F control motions in the nonrotating system is confirmed.

Powers, R. W.↗
NASA NTRS1947

A Comparison of the Lateral Motion Calculated for Tailless and Conventional Airplanes

Theoretical analysts of lateral dynamic motion of tailless and conventional airplanes was made for fighter and heavy transport. Their reactions to a lateral gust and control power required by each for simple maneuvers were determined and compared. Both types of airplanes require almost identical aileron control power to perform a given maneuver; tailless airplane requires about 1-2 to 1-3 directional control power of conventional airplane. Tailless airplane also shows greatest displacement for a given disturbance and has least damping in oscillatory mode.

Harper, Charles W.↗
NASA NTRS1997

Molecular Dynamics Simulations of Laser Powered Carbon Nanotube Gears

Dynamics of laser powered carbon nanotube gears is investigated by molecular dynamics simulations with Brenner's hydrocarbon potential. We find that when the frequency of the laser electric field is much less than the intrinsic frequency of the carbon nanotube, the tube exhibits an oscillatory pendulam behavior. However, a unidirectional rotation of the gear with oscillating frequency is observed under conditions of resonance between the laser field and intrinsic gear frequencies. The operating conditions for stable rotations of the nanotube gears, powered by laser electric fields are explored, in these simulations.

Srivastava, Deepak↗
NASA NTRS1991

Numerical prediction of turbulent oscillating flow and associated heat transfer

A crucial point for further development of engines is the optimization of its heat exchangers which operate under oscillatory flow conditions. It has been found that the most important thermodynamic uncertainties in the Stirling engine designs for space power are in the heat transfer between gas and metal in all engine components and in the pressure drop across the heat exchanger components. So far, performance codes cannot predict the power output of a Stirling engine reasonably enough if used for a wide variety of engines. Thus, there is a strong need for better performance codes. However, a performance code is not concerned with the details of the flow. This information must be provided externally. While analytical relationships exist for laminar oscillating flow, there has been hardly any information about transitional and turbulent oscillating flow, which could be introduced into the performance codes. In 1986, a survey by Seume and Simon revealed that most Stirling engine heat exchangers operate in the transitional and turbulent regime. Consequently, research has since focused on the unresolved issue of transitional and turbulent oscillating flow and heat transfer. Since 1988, the University of Minnesota oscillating flow facility has obtained experimental data about transitional and turbulent oscillating flow. However, since the experiments in this field are extremely difficult, lengthy, and expensive, it is advantageous to numerically simulate the flow and heat transfer accurately from first principles. Work done at the University of Minnesota on the development of such a numerical simulation is summarized.

Koehler, W. J.↗
NASA NTRS2016

Flow Energy Piezoelectric Bimorph Nozzle Harvester

A flow energy harvesting device having a harvester pipe includes a flow inlet that receives flow from a primary pipe, a flow outlet that returns the flow into the primary pipe, and a flow diverter within the harvester pipe having an inlet section coupled to the flow inlet, a flow constriction section coupled to the inlet section and positioned at a midpoint of the harvester pipe and having a spline shape with a substantially reduced flow opening size at a constriction point along the spline shape, and an outlet section coupled to the constriction section. The harvester pipe may further include a piezoelectric structure extending from the inlet section through the constriction section and point such that the fluid flow past the constriction point results in oscillatory pressure amplitude inducing vibrations in the piezoelectric structure sufficient to cause a direct piezoelectric effect and to generate electrical power for harvesting.

Sherrit, Stewart↗
NASA NTRS2006

Heat Transfer and Fluid Dynamics Measurements in the Expansion Space of a Stirling Cycle Engine

The heater (or acceptor) of a Stirling engine, where most of the thermal energy is accepted into the engine by heat transfer, is the hottest part of the engine. Almost as hot is the adjacent expansion space of the engine. In the expansion space, the flow is oscillatory, impinging on a two-dimensional concavely-curved surface. Knowing the heat transfer on the inside surface of the engine head is critical to the engine design for efficiency and reliability. However, the flow in this region is not well understood and support is required to develop the CFD codes needed to design modern Stirling engines of high efficiency and power output. The present project is to experimentally investigate the flow and heat transfer in the heater head region. Flow fields and heat transfer coefficients are measured to characterize the oscillatory flow as well as to supply experimental validation for the CFD Stirling engine design codes. Presented also is a discussion of how these results might be used for heater head and acceptor region design calculations.

Jiang, Nan↗
NASA NTRS1985

Flight investigation of stall, spin and recovery characteristics of a low-wing, single-engine, T-tail light airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a four-place, low-wing, single-engine, T-tail, general aviation research airplane at an aft center-of-gravity position. Most stalls resulted in roll-offs. Spins were oscillatory in roll and pitch at 43 deg angle of attack; the magnitude of the oscillations was determined by aileron position. Power, flap deflection, and landing gear position did not affect the angle of attack to the spin. Antispin rudder followed by forward wheel with ailerons neutral produced the fastest and most consistent recoveries but the initial application of recovery controls did not always stop a spin.

Stough, H. P., III↗
NASA NTRS1999

Phase-Shifted Laser Feedback Interferometry

Phase-shifted, laser feedback interferometry is a new diagnostic tool developed at the NASA Lewis Research Center under the Advanced Technology Development (ATD) Program directed by NASA Headquarters Microgravity Research Division. It combines the principles of phase-shifting interferometry (PSI) and laser-feedback interferometry (LFI) to produce an instrument that can quantify both optical path length changes and sample reflectivity variations. In a homogenous medium, the optical path length between two points is the product of the index of refraction and the geometric distance between the two points. LFI differs from other forms of interferometry by using the laser as both the source and the phase detector. In LFI, coherent feedback of the incident light either reflected directly from a surface or reflected after transmission through a region of interest will modulate the output intensity of the laser. The combination of PSI and LFI has produced a robust instrument, based on a low-power helium-neon (HeNe) gas laser, with a high dynamic range that can be used to measure either static or oscillatory changes of the optical path length. Small changes in optical path length are limited by the fraction of a fringe that can be measured; we can measure nonoscillatory changes with a root mean square (rms) error of the wavelength/1000 without averaging.

Ovryn, Benjie↗
NASA NTRS2003

Low Frequency High Amplitude Temperature Oscillations in Loop Heat Pipe Operation

This paper presents a theory that explains low frequency, high amplitude temperature oscillations in loop heat pipe (LHP) operation. Oscillations of the CC temperature with amplitudes on the order of tens of degrees Kelvin and periods on the order of hours have been observed in some LHPs during ambient testing. There are presently no satisfactory explanations for such a phenomenon in the literature. It is well-known that the operating temperature of an LHP with a single evaporator is governed by the compensation chamber (CC) temperature, which in turn is a function of the evaporator heat load, sink temperature, and ambient temperature. As the operating condition changes, the CC temperature will change during the transient but eventually reach a new steady temperature. Under certain conditions, however, the LHP never really reaches a true steady state, but instead displays an oscillatory behavior. The proposed new theory describes why low frequency, high amplitude oscillations may occur when the LHP has a low evaporator power, a low heat sink temperature (below ambient temperature), and a large thermal mass attached to the evaporator. When this condition prevails, there are some complex interactions between the CC, condenser, thermal mass and ambient. The temperature oscillation is a result of the large movement of the vapor front inside the condenser, which is caused by a change in the net evaporator power modulated by the large thermal mass through its interaction with the sink and CC. The theory agrees very well with previously published test data. Effects of various parameters on the amplitude and frequency of the temperature oscillation are also discussed.

Ku, Jentung↗
NASA NTRS1957

Concluding Report of Free-Spinning, Tumbling, and Recovery Characteristics of a 1/18-Scale Model of the Ryan X-13 Airplane, Coord. No. AF-199

An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/18-scale model of the Ryan X-13 airplane to determine its spin, recovery, and tumbling characteristics, and to determine the minimum altitude from which a belly landing could be made in case of power failure in hovering flight. Model spin tests were conducted with and without simulated engine rotation. Tests without simulated engine rotation indicated two types of spins: one, a slightly oscillatory flat spin; and the other, a violently oscillatory spin. Tests with simulated engine rotation indicated that spins to the left were fast rotating and steep and those to the right were slow rotating and flat. The optimum technique for recovery is reversal of the rudder to against the spin and simultaneous movement of the ailerons to full with the spin followed by movement of the elevators to neutral after the spin rotation ceases. Tumbling tests made on the model indicated that although the Ryan X-13 airplane will not tumble in the ordinary sense (end-over-end pitching motion), it may instead tend to enter a wild gyrating'motion. Tests made to simulate power failure in hovering flight by dropping the model indicated that the model entered what appeared to be a right spin. An attempt should be made to stop this motion immediately by moving the rudder to oppose the rotation (left pedal), moving the ailerons to with the spin (stick right), and moving the stick forward after the spin rotation ceases to obtain flying speed for pullout. The minimum altitude required for a belly landing in case of power failure in hovering flight was indicated to be about 4,200 feet.

Bowman, James S., Jr.↗
NASA NTRS1984

Electromagnetic damping of neutron star oscillations

A simple model of magnetic field perturbations driven by neutron star oscillations is used to estimate the electromagnetic power radiated by g-modes and torsional oscillations. The calculation assumes that the neutron star has a frozen-in magnetic field which is perturbed by the oscillatory motions of the surface. The disturbances propagate into the vacuum as outgoing electromagnetic waves. The relative effectiveness of Joule heating of the neutron star crust by pulsation-induced electric currents is estimated. It is concluded that electromagnetic damping is the dominant energy dissipation mechanism for quadrupole g-mode oscillations of neutron stars. For dipole spheroidal modes, both electromagnetic radiation and Joule heating are important, and there is no gravitational radiation emitted by these modes.

Mcdermott, P. N.↗
NASA NTRS1965

Operational Experiences of Turbine-Powered Commercial Transport Airplanes

Recent results obtained from NASA V-G and VGH recorders installed on commercial turbine-powered transports have indicated that exceedances of placard speeds appear to have been significantly reduced since the placard speeds have been redefined and changes made in the aural warning. Oscillatory accelerations and unusual events, such as large or rapid departures from the planned flight profile, occur less frequently. Landing-impact accelerations are higher for turbine transports than for piston transports and vary with operator. The total in-flight acceleration experiences for turbine transports, however, are not significantly different from those for four-engine piston transports.

Hunter, Paul A.↗
NASA NTRS1977

Optimal low-thrust takeoff from an orbit about an oblate planet

Future space missions to the outer planets may depend upon the use of low-thrust propulsion systems. As these planets are decidedly oblate, the question of the effect of that oblateness on a low-thrust trajectory is of some interest. In this paper the problem of optimal energy increase is attacked under the assumption that the coefficients for the second zonal harmonic, and the nondimensional thrust acceleration are the same order of magnitude. By means of a two-variable asymptotic expansion technique, a near optimal control program is generated and the first-order uniformly valid approximation for the corresponding trajectory is obtained. Tangential thrust is shown to be a good near-optimal thrust program even in the presence of oblateness effects. The optimal control program is found to be oscillatory and quite similar to the optimal control for energy increase in an inverse square gravitational field.

Jacobson, R. A.↗
NASA NTRS2006

Thrust Stand for Electric Propulsion Performance Evaluation

An electric propulsion thrust stand capable of supporting testing of thrusters having a total mass of up to 125 kg and producing thrust levels between 100 microN to 1 N has been developed and tested. The design features a conventional hanging pendulum arm attached to a balance mechanism that converts horizontal deflections produced by the operating thruster into amplified vertical motion of a secondary arm. The level of amplification is changed through adjustment of the location of one of the pivot points linking the system. Response of the system depends on the relative magnitudes of the restoring moments applied by the displaced thruster mass and the twisting torsional pivots connecting the members of the balance mechanism. Displacement is measured using a non-contact, optical linear gap displacement transducer and balance oscillatory motion is attenuated using a passive, eddy-current damper. The thrust stand employs an automated leveling and thermal control system. Pools of liquid gallium are used to deliver power to the thruster without using solid wire connections, which can exert undesirable time-varying forces on the balance. These systems serve to eliminate sources of zero-drift that can occur as the stand thermally or mechanically shifts during the course of an experiment. An in-situ calibration rig allows for steady-state calibration before, during and after thruster operation. Thrust measurements were carried out on a cylindrical Hall thruster that produces mN-level thrust. The measurements were very repeatable, producing results that compare favorably with previously published performance data, but with considerably smaller uncertainty.

Polzin, Kurt A.↗