SEARCH · Search NASA

Results for “paraffin fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Toward net-zero sustainable aviation fuel with wet waste–derived volatile fatty acids

Significance To meet the growing demand for sustainable aviation fuels (SAF), conversion pathways are needed that leverage wet waste carbon and meet jet fuel property specifications. Here, we demonstrate SAF production from food waste–derived volatile fatty acids (VFA) by targeting normal paraffins for a near-term path to market and branched isoparaffins to increase the renewable content long term. Combining these distinct paraffin structures was shown to synergistically improve VFA-SAF flash point and viscosity to increase the renewable blend limit to 70%. Life cycle analysis shows the dramatic impact on the carbon footprint if food waste is diverted from landfills to produce VFA-SAF, highlighting the potential to meet jet fuel safety, operability, and environmental goals.

09 BIOMASS FUELS↗

DOE OSTI2024

ENDF/B-VIII.1: Thermal Neutron Scattering Sublibrary

The thermal neutron scattering law (TSL) sublibrary aims to describe the interaction of incident neutrons at thermal or sub-thermal energies with different compound materials such fuels, moderators and special-purpose materials. In ENDF/B-VIII.1 there was a large number of new and updated TSL evaluations, including traditional moderators (light water, Beryllium metal, Beryllium Oxide, Calcium Hydride, plastics (Polystyrene and Lucite), graphite (reactor-grade and crystalline), anhydrous Hydrogen Fluoride, and heavy paraffinic oil); exotic moderators (Beryllium Carbide, Zirconium Hydride, Yttrium Hydride, Lithium-7 Hydride and Deuteride), FLiBe molten salt, structural materials and cladding (Silicon Carbide, Silicon Dioxide, Zirconium Carbide), fuels (Plutonium Dioxide, Uranium Carbide, Uranium metal, Uranium Nitride, Uranium Dioxide, Uranium Hydride), and special purpose materials. In ENDF/B-VIII.1 we also distribute alongside the evaluated files, a comma-separated file (CSV), named TSL_MAT_numbers.csv, which lists all evaluated files in the current release and their corresponding unique MAT number.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

The effect on soot and its gas precursors of doping ethylene with 2,2,4,6,6-pentamethyl-heptane in the nitrogen-fuel stream of a laminar non-premixed Planar Mixing Layer Flame (PMLF)

Synthetic Aviation Turbine Fuels (SATFs) are promising for reducing soot emissions from the aviation sector and diversifying Jet Fuel (JF) sources. Accurately predicting the combustion and emissions behavior of SATFs (and other JFs) necessitates robust experimental databases to elucidate the chemistry of long-chain iso-paraffins, which can compose up to two-thirds of SATF blends and whose behavior is considered to be well-represented by that of iso-dodecane isomers. Here, this study characterizes two laminar non-premixed Planar Mixing Layer Flames (PMLFs) with mild soot loads fueled by nitrogen-diluted ethylene, pure and doped with 2,2,4,6,6-pentamethyl-heptane, respectively. The two PMLFs have the same stoichiometric mixture fraction and total hydrocarbon mole fraction in the fuel stream (X F,F =X C2H4,F +X C12H26,F = 0.260), resulting in nearly the same maximum temperature (T max ≈1800 K) and simple identification of the effects of doping. Importantly, any horizontal PMLF cross-section has a self-similar structure that can be modeled as an equivalent One-Dimensional Counterflow Flame (1D-CF) with vanishingly small strain rate (a). The cross-section at a Height Above the Burner (HAB) of 50 mm is characterized in terms of C 0 -C 18 gas species using capillary sampling followed by GC-MS analyses. Laser-Induced Emission Spectroscopy (LIES) quantifies the soot volume fraction (ƒ v ) profiles at HAB=25 and 50 mm where Elastic Laser Light Scattering (E-LLS) is performed to determine the a of the equivalent 1D-CFs and the profile of the E-LLS equivalent diameter ( d 6,3 ) of soot. The substitution of 1500 ppm of ethylene with 2,2,4,6,6-pentamethyl-heptane causes an increase of ≈1.5 in the concentrations of several polycyclic aromatic hydrocarbons and fv. Concurrently, the measured d 6,3 doubles in the oxidizer stream, yet remains the same in the fuel stream, at HAB=50 mm. Instead, at HAB= 25 mm, the iso-dodecane doping does not affect the d 6,3 profile in either stream. The experimental results partially validate the chemical reactions and soot formation kinetic model developed at Lawrence Livermore National Laboratory and provide directions to further improve its predictions.

Iso-dodecane (2,2,4,6,6-Pentamethyl-Heptane)↗

DOE OSTI2022

Fuels and methods of making the same

The present disclosure relates to a method that includes a first treating of a first mixture that includes a carboxylic acid having between 2 and 12 carbon atoms, inclusively, to form a second mixture that includes a ketone having between 2 and 25 carbon atoms, inclusively, and a second treating of at least a first portion of the second mixture to form a first product that includes a paraffin having 8 or more carbon atoms.

09 BIOMASS FUELS↗

DOE OSTI2025

Pressure-stable supported ionic liquid membranes using isoporous supports for evaluating pure- and mixed-gas light paraffin fractionation

Advances in horizontal drilling and hydraulic fracturing have spurred the growth of domestic U.S. energy production. Membranes, typically silicone rubbers, have found utility in shale gas treatment as fuel gas conditioning units to selectively remove C 2 + hydrocarbons at pressures up to 30 bar, producing clean CH 4 for gas engines. However, more selective materials could be beneficial for broader shale gas treatment applications, such as dew point control units. Supported ionic liquid membranes (SILMs) offer a potential opportunity for improving C 3 H 8 /CH 4 selectivity, but they lack pressure-stability. Here, we report C 3 H 8 /CH 4 selective and pressure-stable SILMs using isoporous supports. SILMs with supports that had minimal defects remained stable up to 15 bar of transmembrane pressure. This stability allowed for pure- and mixed-gas testing of the resulting membranes at elevated pressures. Furthermore, these tests revealed that low viscosity ILs (<100 cp) may display mixed-gas permeances and permselectivity nearly identical to pure-gas results. On the other hand, higher viscosity ILs may display increasing permeances and permselectivity with increasing C 3 H 8 fugacity, similar to rubbery polymers. Ultimately, the SILMs demonstrated relatively high pressure-stability due to the isoporous supports and competitive mixed-gas C 3 H 8 /CH 4 permselectivity compared to silicone rubber.

Rosenthal, Justin J. [University of Texas at Austi↗

DOE OSTI2022

Design of Transition-Metal/Zeolite Catalysts for Direct Conversion of Coal-derived CO 2 to Aromatics

This project introduces a lab-scale, stand-alone process to produce aromatics from CO 2 . Besides reducing the amount of coal-derived CO 2 emission, this process can provide new approaches to produce valuable chemicals such as benzene, toluene, and xylene (BTX). These chemicals are the starting material in various industries such as pharmaceuticals, polymers, paints, and coatings. The focus of the project is on developing a suitable reaction configuration, feed composition, and catalyst combination that leads to high aromatics selectivity and CO 2 conversions. To achieve these objectives, computational catalysis will accompany hands-on experiments to provide insights to potential transition metals or alloys that may serve as optimal active sites for different steps of the reaction mechanism, such as reduction of CO 2 and dehydration (in the case of alcohol intermediates) and oligomerization (in the case of paraffins or olefins) of intermediate hydrocarbons.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

Design of Transition-Metal/Zeolite Catalysts for Direct Conversion of Coal-derived CO 2 to Aromatics

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2026

Harnessing ketones as hydrogen acceptors for atom-efficient upgrading of oxygenates to fuels over H/ZSM-5

Heterogeneous mixtures of bio-derived oxygenates are promising feedstocks for synthetic aviation fuel (SAF), but conversion strategies for one common component—short-chain (C 5–7 ) internal ketones—are lacking. Previous work has shown that cyclization of ketones over H/ZSM-5 is limited by its high productivity of light paraffins. We study 4-heptanone upgrading over H/ZSM-5 and show that aromatics and olefins can be formed at high carbon yield when operating at up to 90% conversion. The yield of desirable products is not impacted by the introduction of a recycle stream of the unconverted 4-heptanone and other products with similar boiling points. We hypothesize, based on first-principles calculations, that the higher olefin yield is driven by the ease of hydrogen transfer to unreacted ketones as opposed to hydrogenating olefin products. We demonstrate how this ease of hydrogen transfer to ketones can be leveraged to enhance olefin selectivity in the conversion of methanol to olefins as well by co-feeding ketones. Olefinic products of the cyclization reaction are then oligomerized to a SAF blendstock to demonstrate an end-to-end ketone-to-SAF process facilitated by upgrading ketones over H/ZSM-5 at partial conversion with a recycle stream. The results of this work demonstrate a strategy to improve the carbon yield from bio-derived acids to SAF to over 75%, representing a relative improvement of more than 50% compared to previously reported data.

08 HYDROGEN↗

DOE OSTI2021

Supercritical water co-liquefaction of LLDPE and PP into oil: properties and synergy

The major plastic wastes are always mixtures, which are difficult to separate to treat in practice. Because of some possible cross-reactions, the degradation behaviors of plastics could not be mathematically represented by a simple addition of each polymer according to their proportions. This work examines supercritical water (scH 2 O) to liquefy poly-ethylene and poly-propylene mixtures into an oil with special interest in the oil quality and positive effect. Additionally, linear low-density polyethylene (LLDPE) and polypropylene (PP) were chosen as parent materials because of their high proportions in plastic wastes. The results show that a high conversion rate of around 99.75% was achieved with as high as 90.7 wt% oil yield without additional catalysts or hydrogen. The scH 2 O co-liquefaction of the LLDPE/PP mixture was different from that of the single polymer along with an improvement in the oil yield. Cyclic hydrocarbon ( i.e. , cyclic) generation was promoted while the production of paraffins was hindered in scH 2 O co-liquefaction using a mixture of LLDPE/PP. TGA reveals that the scH 2 O co-liquefaction of LLDPE/PP mixtures generated more diesel and lubricant oils and less gasoline and (jet fuel + light diesel) oils, thus slightly lowering the oil quality. Overall, the supercritical fluid technology was a powerful and promising means to liquefy mixed plastic wastes into oil at a high conversion rate free of catalysts or hydrogen.

42 ENGINEERING↗

DOE OSTI2024

Renewable Aromatics from Syngas

This study focuses on developing a catalytic process for the aromatization of mixed olefin (comprised of C 2 -C 6 ) over various metal doped zeolites towards the formation of large aromatics (preferably C 8 -C 16 ) compliance to the sustainable aviation fuel (SAF). Experiments were carried out using model olefin feedstocks containing either ethylene (C 2 ) or mixture of C 2 and C 3+ olefins. Both the catalyst composition and process parameters were evaluated in detail to identify their impact on the formation large aromatics. We specifically focus on the aromatization of ethylene as the model reaction and evaluated the impact of C 2+ olefins and paraffins that may present in the real feedstock. In all the reaction condition, aromatization of ethylene was used as the baseline to evaluate the effect of larger olefins or paraffins. Our results show that at this reaction condition paraffins remained either inert or show positive impact on the formation of large aromatics. While C 2 and C 3 olefins are highly reactive towards aromatization during reaction condition, large olefins are less reactive and thus, strategy was developed to oligomerize these large olefins (C 4+ ) alongside the aromatization of smaller olefins (C 2 /C 3 ).

10 SYNTHETIC FUELS↗

DOE OSTI2025

Co-depolymerization of lignin and plastic waste using hydrothermal liquefaction process

Sustainable valorization of underutilized lignin and plastic waste beyond incineration is critical for producing renewable fuels. Hydrothermal liquefaction (HTL) provides a promising approach to convert wet lignin and plastics into high-quality oils without the need for prior drying of wet lignin. Here, this study examines the effects of temperature (300–400 °C), residence time, and polymer molecular weight on product yield and composition during HTL of polyethylene (PE), polypropylene (PP), and lignin under subcritical and supercritical water conditions. For PE, oil yields increased with temperature, with low molecular weight (LMW) PE achieving a maximum of ∼93 % at 400 °C for 30 min, while high molecular weight (HMW) PE reached ∼86 % at 400 °C for 1 h. Lignin and PP exhibited optimal oil yields at intermediate temperatures, decreasing at higher temperatures due to secondary reactions and char formation. Lignin yielded a maximum of ∼22 % oil at 300 °C for 30 min, LMW PP ∼88 % at 375 °C for 1 h, and HMW PP ∼83 % at 400 °C for 1 h. GC–MS analysis revealed that lignin oils were rich in phenols and alkylphenols, while PE and PP oils were dominated by paraffins and olefins. Oxygenated compounds in PE decreased at higher temperatures, improving oil quality. Co-liquefaction of lignin with plastics enhanced oil yields and energy content under specific conditions, demonstrating synergistic effects dependent on plastic type, molecular weight, and HTL conditions. These findings highlight the potential of HTL to produce high-energy, value-added fuels from lignin–plastic mixtures.

09 - BIOMASS FUELS↗

DOE OSTI2023

Thermochemical processes for CO 2 hydrogenation to fuels and chemicals: Challenges and opportunities

This manuscript discusses the potential use of CO 2 as a carbon and oxygen carrier to return it to the carbon life cycle in the form of fuels or chemicals via thermochemical catalytic pathways. Theoretically, CO 2 hydrogenation can form a variety of fuels and chemicals. Practically, however, the selectivity, conversion, operating range, and kinetic limitations and operational cost determine the end product. Because of their high value and versatility as a chemical or fuel, small olefins (i.e., C 2 H 4 ) and methanol are often considered as target species. Whether alcohol or olefin formation, CH 4 and CO are the nature’s primary choices of CO 2 conversion. They can be formed over a wide operating temperature, pressure, and CO 2 :H 2 ratios. They are often competitive carbon species in olefin or methanol formation steps. Although they are less valuable as end products, they can be used as intermediate species. Secondary processes of CO and CH 4 to form chemicals and fuels can increase the overall CO 2 hydrogenation yield. Independent of the choice of end product, CO 2 hydrogenation requires hydrogen. Pure hydrogen derived mostly from fossil fuels adds to the overall process cost and also increases the CO 2 emissions. Hydrogen produced from water electrolysis is a renewable green pathway but is limited by the process efficiency and cost. As an alternative to pure hydrogen, low-value, small chain paraffins are suggested as the hydrogen carriers. Carbon dioxide–assisted oxidative dehydrogenation of paraffins to olefins process is a direct pathway to olefin formation. The paper discusses these potential pathways for CO 2 utilization based on theoretical analysis and recent advances in academia and industry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Experimental and kinetic modeling study of tetralin: A naphtheno-aromatic fuel for gasoline, jet and diesel surrogates

Distillate fuels contain significant proportions of naphtheno-aromatic components and tetralin is a suitable surrogate component to represent this molecular moiety. The presence of aromatic and naphthyl rings makes kinetic modeling of tetralin very challenging. Primary radicals formed during the oxidation of tetralin can be aryl, benzylic or paraffinic in nature. Using available information on reaction paths and rate constants of naphthenes and alkyl-aromatics, in this study a kinetic model of tetralin has been developed with emphasis on low-temperature chemistry and high-pressure conditions. Due to the lack of high-level quantum chemical calculations on reaction pathways of tetralin, analogous rates from ab-initio studies on benzylic and paraffinic radicals have been adopted here. Some modifications to the reaction rate rules are incorporated to account for the unique characteristics of tetralin's molecular structure. Important reaction channels have been identified using reaction path and brute force sensitivity analyses. In order to investigate the model performance at low temperatures, new experiments are carried out in a rapid compression machine on blends of tetralin and 3-methylpentane. Blending of low-reactivity tetralin with a high-reactivity alkane allowed the investigation of tetralin ignition at very low temperatures (665 – 856 K). The kinetic model developed in the current study is found to predict the current experiments and literature data adequately. The new model will aid in high-fidelity surrogate predictions at engine-relevant conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Using Separation-Enhanced Isotope Ratio Mass Spectrometry to Enable Increased Renewable Carbon Content in Transportation Fuels (CRADA 525)

Stable isotope ratio measurements of carbon atoms using isotope ratio mass spectrometry (IRMS) can be an effective tool for quantifying biogenic carbon in co-processed fuels, with results approaching the precision and accuracy of accelerator mass spectrometry (AMS). The lower cost of an IRMS may enable deployment to refineries, improving access and analysis turnaround times (≤2 hours), and, by extension, provide data that can allow process optimization to maximize renewable carbon in desired refinery products. This project explored the integration of chemical separation with IRMS analyses to enable highly detailed tracking of biogenic carbon into fuel product streams separated by boiling point range, chemical class, or specific compound. Forty-nine fuels and fuel components of fossil and biogenic origin, spanning gasoline and diesel boiling point ranges, were received from three refiners and were analyzed for their δ 13 C values via IRMS. Results spanned a 13 C range from ca. 10‰ to 44‰ and reflect materials derived from sustainable sources (e.g., C4 or C3 plants, animal-based pathways, syngas) or from fossil-derived fuels. Common ranges are approximately 18‰ to 9‰ and approximately 30‰ to 20‰ for C4 and C3 plants, respectively, and approximately 34‰ to 24‰ and approximately 70‰ to 33‰ for petroleum-derived fuels and methane, respectively. Fuel-like standards were developed and tested using direct-injection elemental analyzer (EA) IRMS for liquid fuels. This method was compared with the published methods, yielding statistically similar results. Four blend curve sets were produced ranging from 0% to 100% of a fuel containing biogenic carbon, focusing on 0% to 10% biogenic carbon. Linear fits were the most applicable for two of the four blend curve sets; however, two sets were found to exhibit slightly quadratic behavior, which was more pronounced in low biogenic blend samples, necessitating second-order fits. The origin of the slight quadratic behavior remains unclear; however, the discussion points to possible interpretations. CanmetENERGY thoroughly characterized a majority of the samples using one- and two-dimensional gas chromatography (GC and GC×GC, respectively) and other analyses. Selected samples were subjected to solid phase extraction (SPE) for saturate, olefin, aromatic, and polar (SOAP) analysis, and the resulting solvent-diluted fractions containing saturates and aromatics were returned to Pacific Northwest National Laboratory (PNNL), where the solvent was removed via evaporation or physical separation using GC techniques. Characterization and separations provided an understanding of saturate and aromatic content, as well as boiling point ranges for each sample and sample fraction. Samples resulting from SPE were examined using EA-IRMS and gas chromatography combustion IRMS (GC-C-IRMS) analyses. Both approaches suggest that the range in values between end-members can be increased by selecting the paraffinic or aromatic fraction of the end-member or by selecting among individual compounds resulting from GC separation of the paraffinic fractions. Considerable work remains to put these approaches into practice and statistically validate the benefit for using a fraction or individual compound over bulk analysis of a sample. However, initial results suggest that separations provide advantages for samples having blend ratios of less than 10% biogenic blendstocks. 13 C results showed statistically similar biofuel blend results to those obtained at PNNL, although additional work is needed to obtain better reproducibility. Select samples were sent to Los Alamos National Laboratory (LANL) for IRMS measurements and Beta Analytics for AMS measurements. This work suggests that IRMS and AMS yield closely comparable results and in some circumstances, IRMS could serve as a surrogate for AMS. While additional work is needed to better resolve statistical advantages for separations and better show the comparable nature of IRMS and AMS in both the biogenic carbon analysis of bulk chemical classes, initial results from this study suggest that these should be pursued in order to proliferate this approach for quantifying biogenic carbon in transportation fuels to the refinery level, thereby potentially enabling process optimization in co-processing scenarios.

09 BIOMASS FUELS↗

DOE OSTI2021

Center for Gas Separations (CGS)

The total energy consumption in the U.S. has been rising steadily for decades, and it currently amounts to ~98,000 TBtu/yr, with approximately 30% of this total attributable to the industrial sector. Reasonable estimates indicate that 45–55% of total industry energy consumption derives from chemical separations, and for example, over 120 TBtu/yr alone is used in carrying out olefin/paraffin separations via energy-intensive cryogenic distillation. Therefore, the pursuit of new, even radically different approaches to some of the most energy-intensive industrial separations processes is an imperative scientific pursuit for reducing energy consumption toward a more sustainable future. Adsorbent and membrane-based separations can require a fraction of the energy needed for distillation methods, and as such are considered promising solutions for balancing increasing energy demand in the U.S. with the need for a massive reduction in energy consumption. Although considerable research effort has been devoted to the design of materials capable of carrying out various gas separations, usually operating through size-selective, chemisorptive, or physisorptive mechanisms, it remains a great challenge to design materials that function adequately for real-world applications. Indeed, the chemical and physical differences between molecules in gas mixtures of interest are often small, and therefore it is necessary, through the use of nanoscience and synthetic chemistry, to engineer unprecedented molecular-level control in adsorbate–adsorbent interactions. The overarching mission of the Center for Gas Separations (CGS) was to discover fundamental innovations that have the potential to dramatically reduce the energy associated with critical gas separations. In particular, the CGS developed novel synthetic routes, guided by molecular chemistry principles, as well as advanced characterization and computational methods, that have enabled the discovery of new materials and membranes tailor-made to exhibit exceptional performance for a range of gas separations processes, as required in the clean use of fossil fuels and in reducing CO 2 emissions from industry. A challenge of this magnitude required the collaboration and synergy of a large team of researchers with expertise in materials synthesis, characterization, and computations. During the 11-year project period, the CGS created a range of new materials within the family of highly-tunable, porous solids known as metal–organic frameworks (MOFs). These new frameworks demonstrate novel mechanisms for key industrial gas separations, including revolutionary new cooperative adsorption processes that enable low-energy CO 2 and CO capture, and are capable of efficiently separating olefins from paraffins, O 2 from air, and the shape-selective separation of alkane isomers. In addition, the CGS developed new strategies for incorporating these materials into composite membranes toward highly efficient and selective membrane-based separations. As a testament to the success of the CGS, two start-up companies, Mosaic Materials,4 Inc. and Flux Technology, Inc., grew out of these research efforts, and these companies are seeking to commercialize MOF and composite membranes materials for key separations in industry, including large-scale CO 2 capture and hydrocarbon separations, respectively. Another company, framergy, Inc., licensed IP resulting from CGS research toward the commercialization of adsorbents for various energy-relevant applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

A 100+ RON Gasoline Blendstock for High Efficiency, Low Emission Vehicles Engines - CRADA 493 (Final Report)

This study aimed at demonstrating production of a 100+RON gasoline fraction from a linear olefins feedstock to help improve further the viability and flexibility of the Pacific Northwest National Laboratory/ LanzaTech alcohol-to-jet (ATJ) patented process that converts ethanol from LanzaTech’s syngas fermentation process to low aromatic jet-range iso-paraffins. To achieve a high RON gasoline and ultimately a 100+RON, the technical approach consisted of converting the linear olefins into an iso-olefins rich mixture and then oligomerizing the iso-olefins rich mixture into high RON compounds in a single bed loaded with an acid catalyst that allows conversion at low reaction temperature. Three families of acid catalysts labeled as type A, B and C were investigated for the single-bed conversion of linear olefins into high RON gasoline range compounds. The effects of the nature of the catalyst, acid sites concentration and operating conditions were investigated. Fuel properties measurements and engine testing were conducted for the most promising catalyst. For type A catalysts, we demonstrated that the conversion increases with the increase of the Brönsted acid site concentration and that lower reaction temperature favors the formation of desired highly branched compounds. The highest dRON obtained with type A catalyst was equal to 94 (from NMR and IQT). Type B catalysts appear very effective for producing dimethyl-olefins compounds when operating at low reaction temperature (i.e., < 100°C). The highest dRON obtained with type B catalyst was equal to 92. The results suggest that type B catalysts are less favorable to internal conversion of linear olefins into iso-olefins compared to type A catalysts which leads to the formation of a gasoline blendstock with a lower dRON. A Type C catalyst that is less commonly used for production of gasoline range compounds from linear olefins was investigated due to its ability to favor conversion of linear olefins into iso-olefins. Compared to type A and type B catalyst, type C favors the formation of highly branched compounds (i.e., with 3+ methyl groups) in the gasoline range. Indeed, a gasoline blendstock containing about 33 wt.% of highly branched compounds was produced with type C catalyst while maintaining a high linear olefins conversion (i.e., 70%). A large quantity of this gasoline blendstock was produced and fuel properties measurements including engine testing for Research Octane Number (RON), Motor Octane Number (MON) and octane sensitivity (S) were conducted. A high RON = 97, MON = 82.7, S =14.3, AKI = 90 and HoV = 334.1kJ/kg were measured. While a RON of 100 was not achieved, the fuel properties of the gasoline blendstock are very acceptable as compared to current premium gasoline. Overall, these results highlight the potential for producing a high RON/ premium gasoline blendstock starting from a linear olefins feedstock.

02 PETROLEUM↗

DOE OSTI2022

Benchmarking Cu/BEA and HBEA catalysts for high-octane gasoline synthesis

We distinguish rates at which carbon deposition occurs during initiation, rates at which catalytic centers are lost during deactivation, and paraffin-to-olefin ratio during propagation as benchmarks that distinguish 5 wt% Cu/H-BEA and H-BEA (Si/Al = 13.5) catalysts during dimethyl ether (DME) homologation in the presence of hydrogen. Studies that systematically vary initial DME contact time (210, 94, and 45 mol H+, initial s (mol C ) -1 ), DME pressure (4 and 22 kPa), and H 2 pressure (1, 24, and 48 kPa) reveal that Cu enables lower carbon deposition rates (on a per proton basis) in the induction period, increases the effluent paraffin-to-olefin ratio during propagation, and decreases the instantaneous site-loss yields by a factor of ~ 1.5-2x (moles of active sites lost per mole of DME) during termination sequences thus affecting the degree of product saturation and catalyst stability during DME homologation. Furthermore, these results provide mechanistic insights revealing the critical role of Cu in facilitating DME homologation to high value, high-octane gasoline-range hydrocarbons with higher cumulative turnovers than proton form H-BEA.

09 BIOMASS FUELS↗