Results for “parameter sweep” — Page 2

NASA NTRS1984

Aeroelastic considerations for torsionally soft rotors

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and six tip designs were tested on the torsionally soft blades. The designs incorporated a systemmatic variation in geometric parameters including sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. A track sensitivity study was also conducted at several advance ratios for both rotors. Based on the test results, tip parameter variations generated significant rotor performance and loads differences for both baseline and torsionally soft blades. Azimuthal variation of elastic twist generated by variations in the tip parameters strongly correlated with rotor performance and loads, but the magnitude of advancing blade elastic twist did not. In addition, fixed system vibratory loads and rotor track for potential conformable rotor candidates appears very sensitive to parametric rotor changes.

Mantay, W. R.↗

NASA NTRS1976

Water vapor diffusion membranes, 2

Transport mechanisms were investigated for the three different types of water vapor diffusion membranes. Membranes representing porous wetting and porous nonwetting structures as well as dense diffusive membrane structures were investigated for water permeation rate as a function of: (1) temperature, (2) solids composition in solution, and (3) such hydrodynamic parameters as sweep gas flow rate, solution flow rate and cell geometry. These properties were measured using nitrogen sweep gas to collect the effluent. In addition, the chemical stability to chromic acid-stabilized urine was measured for several of each type of membrane. A technology based on the mechanism of vapor transport was developed, whereby the vapor diffusion rates and relative susceptibility of membranes to fouling and failure could be projected for long-term vapor recovery trials using natural chromic acid-stabilized urine.

Holland, F. F.↗

NASA NTRS2005

The Effect of Tip Geometry on Active-Twist Rotor Response

A parametric examination of the effect of tip geometry on active-twist rotor system response is conducted. Tip geometry parameters considered include sweep, taper, anhedral, nonlinear twist, and the associated radial initiation location for each of these variables. A detailed study of the individual effect of each parameter on active-twist response is presented, and an assessment offered of the effect of combining multiple tip shape parameters. Tip sweep is shown to have the greatest affect on active-twist response, significantly decreasing the response available. Tip taper and anhedral are shown to increase moderately the active-twist response, while nonlinear twist is shown to have a minimal effect. A candidate tip shape that provides active-twist response equivalent to or greater than a rectangular planform blade is presented.

Wilbur, Matthew L.↗

NASA NTRS1978

An optimum PN code search technique for a given apriori signal location density

A method is presented for optimizing (minimizing) the acquisition time for a PN-type spread spectrum system when the a priori probability density function is not uniform. For an assumed a priori Gaussian density function, calculations show that the acquisition time, when the 0.5 probability acquisition time is used as a measure of acquisition time, is reduced by 40% for a cell detection probability of 0.25 and when three sweeps are used. For the same parameters and with four sweeps the acquisition time is reduced by 41%. When the acquisition time probability is set to 0.9 instead of 0.5, the reduction is 25% of the uniform sweep time.

Holmes, J. K.↗

NASA NTRS1993

Computational parametric study of sidewall-compression scramjet inlet performance at Mach 10

A computational parametric study of three-dimensional, sidewall-compression scramjet inlets was performed to identify the effects of geometric parameters on inlet performance. The parameters were the leading-edge sweep angle, varied between 30 and 60 deg, and the leading-edge position of the cowl, located at the throat and at two forward positions. A laminar boundary layer with cold-wall (T(sub wall) = 300 K (540 R)) boundary conditions was imposed. The parametric study was performed for a Mach number of 10 and a unit free-stream Reynolds number of 7.06 x 10(exp 6) per meter (2.15 x 10(exp 6) per foot) at a geometric contraction ratio of 5. The performance of each configuration was evaluated in terms of the mass capture, throat Mach number, total pressure recovery, kinetic energy efficiency, and internal compression. One computation of an unswept configuration was included as a baseline to determine the effects of introducing leading-edge sweep on the flow-field parameters. The purpose of the computational parametric study was to perform a trade-off of the effects of various parameters on the global performance of the inlet. Although no single optimal configuration emerged, trade-offs among the stated performance parameters identified a leading-edge sweep angle of 45 deg as possessing the most attractive performance characteristics.

Holland, Scott D.↗

NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Fertis, D. G.↗

NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Maser, J. G.↗

NASA NTRS1975

Normal- and oblique-shock flow parameters in equilibrium air including attached-shock solutions for surfaces at angles of attack, sweep, and dihedral

Normal- and oblique-shock flow parameters for air in thermochemical equilibrium are tabulated as a function of shock angle for altitudes ranging from 15.24 km to 91.44 km in increments of 7.62 km at selected hypersonic speeds. Post-shock parameters tabulated include flow-deflection angle, velocity, Mach number, compressibility factor, isentropic exponent, viscosity, Reynolds number, entropy difference, and static pressure, temperature, density, and enthalpy ratios across the shock. A procedure is presented for obtaining oblique-shock flow properties in equilibrium air on surfaces at various angles of attack, sweep, and dihedral by use of the two-dimensional tabulations. Plots of the flow parameters against flow-deflection angle are presented at altitudes of 30.48, 60.96, and 91.44 km for various stream velocities.

Hunt, J. L.↗

NASA NTRS2016

Active Flow Control Using Sweeping Jet Actuators on a Semi-Span Wing Model

Wind tunnel experiments were performed using active flow control on an unswept semispan wing model with a 30% chord trailing edge flap to aid in the selection of actuators for a planned high Reynolds number experiment. Two sweeping jet actuator sizes were investigated to determine the influence of actuator size on the active flow control system efficiency. Sweeping jet actuators with orifice sizes of 1 mm x 2 mm and 2 mm x 4 mm were selected because of the differences in actuator jet sweep angle. The parameters that were varied include actuator momentum, freestream velocity, and trailing edge flap deflection angle. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the two actuators. In addition to the wind tunnel experiments, benchtop studies of the actuators were performed to characterize the jets produced by each actuator. Benchtop investigations of the smaller actuator reveal that the jet exiting the actuator has a reduced sweep angle compared to published data for larger versions of this type of actuator. The larger actuator produces an oscillating jet that attaches to the external di↵user walls at low supply pressures and produces the expected sweep angles. The AFC results using the smaller actuators show that while the actuators can control flow separation, the selected spacing of 3.3 cm may be too large due to the reduced sweep angle. In comparison, the spacing for the larger actuators, 6.6 cm, appears to be optimal for the Mach numbers investigated. Particle Image Velocimetry results are presented and show how the wall jets produced by the actuators cause the flow to attach to the flap surface.

Melton, LaTunia Pack↗

NASA NTRS1993

In-flight investigation of a rotating cylinder-based structural excitation system for flutter testing

A research excitation system was test flown at the NASA Dryden Flight Research Facility on the two-seat F-16XL aircraft. The excitation system is a wingtip-mounted vane with a rotating slotted cylinder at the trailing edge. As the cylinder rotates during flight, the flow is alternately deflected upward and downward through the slot, resulting in a periodic lift force at twice the cylinder's rotational frequency. Flight testing was conducted to determine the excitation system's effectiveness in the subsonic, transonic, and supersonic flight regimes. Primary research objectives were to determine the system's ability to develop adequate force levels to excite the aircraft's structure and to determine the frequency range over which the system could excite structural modes of the aircraft. In addition, studies were conducted to determine optimal excitation parameters, such as sweep duration, sweep type, and energy levels. The results from the exciter were compared with results from atmospheric turbulence excitation at the same flight conditions. The comparison indicated that the vane with a rotating slotted cylinder provides superior results. The results from the forced excitation were of higher quality and had less variation than the results from atmospheric turbulence. The forced excitation data also invariably yielded higher structural damping values than those from the atmospheric turbulence data.

Vernon, Lura↗

NASA NTRS1998

A Methodology for Flight-Time Identification of Helicopter-Slung Load Frequency Response Characteristics Using CIFER

Helicopter slung load operations are common in both military and civil contexts. The slung load adds load rigid body modes, sling stretching, and load aerodynamics to the system dynamics, which can degrade system stability and handling qualities, and reduce the operating envelope of the combined system below that of the helicopter alone. Further, the effects of the load on system dynamics vary significantly among the large range of loads, slings, and flight conditions that a utility helicopter will encounter in its operating life. In this context, military helicopters and loads are often qualified for slung load operations via flight tests which can be time consuming and expensive. One way to reduce the cost and time required to carry out these tests and generate quantitative data more readily is to provide an efficient method for analysis during the flight, so that numerous test points can be evaluated in a single flight test, with evaluations performed in near real time following each test point and prior to clearing the aircraft to the next point. Methodology for this was implemented at Ames and demonstrated in slung load flight tests in 1997 and was improved for additional flight tests in 1999. The parameters of interest for the slung load tests are aircraft handling qualities parameters (bandwidth and phase delay), stability margins (gain and phase margin), and load pendulum roots (damping and natural frequency). A procedure for the identification of these parameters from frequency sweep data was defined using the CIFER software package. CIFER is a comprehensive interactive package of utilities for frequency domain analysis previously developed at Ames for aeronautical flight test applications. It has been widely used in the US on a variety of aircraft, including some primitive flight time analysis applications.

Sahai, Ranjana↗

NASA NTRS2010

Experimental Evaluation of Stagnation Point Collection Efficiency of the NACA 0012 Swept Wing Tip

This paper presents the experimental work of a number of icing tests conducted in the Icing Research Tunnel at NASA Glenn Research Center to develop a test method for measuring the local collection efficiency of an impinging cloud at the leading edge of a NACA 0012 swept wing and with the data obtained to further calibrate a proposed correlation for such impingement efficiency calculation as a function of the modified inertia parameter and the sweep angle. The preliminary results showed that there could be some limitation of the test method due to the ice erosion problem when encountered, and also found that, for conditions free of such problem, the stagnation point collection efficiency measurement for sweep angles up to 45 could be well approximated by the proposed correlation. Further evaluation of this correlation is recommended in order to assess its applicability for swept-wing icing scaling analysis.

Tsao, Jen-Ching↗

NASA NTRS2014

Icing Analysis of a Swept NACA 0012 Wing Using LEWICE3D Version 3.48

Icing calculations were performed for a NACA 0012 swept wing tip using LEWICE3D Version 3.48 coupled with the ANSYS CFX flow solver. The calculated ice shapes were compared to experimental data generated in the NASA Glenn Icing Research Tunnel (IRT). The IRT tests were designed to test the performance of the LEWICE3D ice void density model which was developed to improve the prediction of swept wing ice shapes. Icing tests were performed for a range of temperatures at two different droplet inertia parameters and two different sweep angles. The predicted mass agreed well with the experiment with an average difference of 12%. The LEWICE3D ice void density model under-predicted void density by an average of 30% for the large inertia parameter cases and by 63% for the small inertia parameter cases. This under-prediction in void density resulted in an over-prediction of ice area by an average of 115%. The LEWICE3D ice void density model produced a larger average area difference with experiment than the standard LEWICE density model, which doesn't account for the voids in the swept wing ice shape, (115% and 75% respectively) but it produced ice shapes which were deemed more appropriate because they were conservative (larger than experiment). Major contributors to the overly conservative ice shape predictions were deficiencies in the leading edge heat transfer and the sensitivity of the void ice density model to the particle inertia parameter. The scallop features present on the ice shapes were thought to generate interstitial flow and horse shoe vortices which enhance the leading edge heat transfer. A set of changes to improve the leading edge heat transfer and the void density model were tested. The changes improved the ice shape predictions considerably. More work needs to be done to evaluate the performance of these modifications for a wider range of geometries and icing conditions

Ice Accretion Software↗

NASA NTRS2014

Icing Analysis of a Swept NACA 0012 Wing Using LEWICE3D Version 3.48

Icing calculations were performed for a NACA 0012 swept wing tip using LEWICE3D Version 3.48 coupled with the ANSYS CFX flow solver. The calculated ice shapes were compared to experimental data generated in the NASA Glenn Icing Research Tunnel (IRT). The IRT tests were designed to test the performance of the LEWICE3D ice void density model which was developed to improve the prediction of swept wing ice shapes. Icing tests were performed for a range of temperatures at two different droplet inertia parameters and two different sweep angles. The predicted mass agreed well with the experiment with an average difference of 12%. The LEWICE3D ice void density model under-predicted void density by an average of 30% for the large inertia parameter cases and by 63% for the small inertia parameter cases. This under-prediction in void density resulted in an over-prediction of ice area by an average of 115%. The LEWICE3D ice void density model produced a larger average area difference with experiment than the standard LEWICE density model, which doesn't account for the voids in the swept wing ice shape, (115% and 75% respectively) but it produced ice shapes which were deemed more appropriate because they were conservative (larger than experiment). Major contributors to the overly conservative ice shape predictions were deficiencies in the leading edge heat transfer and the sensitivity of the void ice density model to the particle inertia parameter. The scallop features present on the ice shapes were thought to generate interstitial flow and horse shoe vortices which enhance the leading edge heat transfer. A set of changes to improve the leading edge heat transfer and the void density model were tested. The changes improved the ice shape predictions considerably. More work needs to be done to evaluate the performance of these modifications for a wider range of geometries and icing conditions.

Icing CFD↗

NASA NTRS1990

A numerical study of the effects of reverse sweep on a scramjet inlet performance

A comparative numerical study of performance parameters of a similar and an opposite sweep sidewall compression inlet is made. The focus of the study is the investigation of the impact of alternate backward-forward sweep on the compression sidewalls as opposed to back-ward sweep on all the sidewalls. Two equivalent scramjet inlet configurations are designed for this purpose. These inlets have the same wetted areas of compression and expansion and same height and width; but in one inlet all the compression surface are swept back (similar sweep inlet) whereas in the other inlet, alternate surfaces are swept backward and forward (opposite sweep inlet). The cowl closure in both cases begins at the start of the throat region. A three-dimensional Navier-Stokes code is used to calculate the flow through these inlets. Results of these calculations are used to compare the two designs for their performance and flow quality. Effects of boundary- layer ingestion on the performance and overall flow features are also investigated.

Kumar, Ajay↗

NASA NTRS1987

Satellite sweeping in offset, tilted dipole fields

The paper presents a theory for the longitudinally averaged satellite sweeping rate in an offset, tilted dipole magnetic field. It includes the reductions in the sweeping rate when the moon radius is not large compared to the gyroradius or the azimuthal drift distance during a bounce period. With a large tilt angle between the magnetic and rotation axes, moons make large excursions in dipole L value, and more than one moon can sweep at a given L. The sweeping rate peaks at the minimum L for each moon. If the gyroradius is large, additional peaks can occur when the particle mirrors near the moon latitude. To illustrate the theory, sweeping rates are evaluated for parameters relevant to the observations at Uranus by the Voyager 2 Low Energy Charged Particles Experiment. Calculated sweeping rates for ions and electrons are typically two or three orders of magnitude less than the strong-diffusion loss rate. The observation of sweeping signatures at Uranus would imply that pitch-angle scattering there occurs at a rate far below the strong-diffusion limit, contrasting with the situation for energetic ions in the inner Jovian magnetosphere.

Paonessa, Mark T.↗

NASA NTRS1974

Comparison of flight data and analysis for hingeless rotor regressive inplane mode stability

Analytical and experimental data obtained during the development of the AH-56A covering stability of the regressive inplane mode, including coupling with other modes such as body and rotor plunge are reported. Data were obtained on two distinctly different control systems; both gyro controlled, but one with feathering moment feedback and the other with direct flapping feedback. A review was made of analytical procedures employed in investigating the stability of this mode and a comparison was made of the analytical and experimental data. The effect of certain parameters including blade droop, sweep, delta 3, alpha 1, vehicle roll inertia, inplane frequency, and rpm and forward speed on the mode were also reviewed. It was shown that the stability of this mode is treatable by analysis and that adequate stability is achievable without recourse to auxiliary inplane damping devices.

Anderson, W. D.↗

NASA NTRS1987

An experimental investigation of the aeromechanical stability of a hingeless rotor in hover and forward flight

Analysis and testing were conducted in the Langley Transonic Dynamics Tunnel to investigate the aeromechanical stability of a soft inplane hingeless rotor model. Rotor stability data were obtained in hover and in forward flight up to an advance ratio of 0.35. Model rotor parameters evaluated were blade sweep and droop, pre-cone of the blade feathering axis, and blade pitch-flap coupling. Data obtained during these tests are presented without analysis.

Yeager, William T., Jr.↗