Search NASA⌕ Search

SEARCH · Search NASA

Results for “parametric”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Extended parametric representation of compressor fans and turbines. Volume 1: CMGEN user's manual

A modeling technique for fans, boosters, and compressors has been developed which will enable the user to obtain consistent and rapid off-design performance from design point input. The fans and compressors are assumed to be multi-stage machines incorporating front variable stators. The boosters are assumed to be fixed geometry machines. The modeling technique has been incorporated into time sharing program to facilitate its use. Because this report contains a description of the input output data, values of typical inputs, and examples cases, it is suitable as a user's manual. This report is the first of a three volume set describing the parametric representation of compressors, fans, and turbines. The titles of the three volumes are as follows: (1) Volume 1 CMGEN USER's Manual (Parametric Compressor Generator); (2) Volume 2 PART USER's Manual (parametric Turbine); (3) Volume 3 MODFAN USER's Manual (Parametric Modulating Flow Fan).

Converse, G. L.↗
NASA NTRS1989

Robustness analysis for real parametric uncertainty

Some key results in the literature in the area of robustness analysis for linear feedback systems with structured model uncertainty are reviewed. Some new results are given. Model uncertainty is described as a combination of real uncertain parameters and norm bounded unmodeled dynamics. Here the focus is on the case of parametric uncertainty. An elementary and unified derivation of the celebrated theorem of Kharitonov and the Edge Theorem is presented. Next, an algorithmic approach for robustness analysis in the cases of multilinear and polynomic parametric uncertainty (i.e., the closed loop characteristic polynomial depends multilinearly and polynomially respectively on the parameters) is given. The latter cases are most important from practical considerations. Some novel modifications in this algorithm which result in a procedure of polynomial time behavior in the number of uncertain parameters is outlined. Finally, it is shown how the more general problem of robustness analysis for combined parametric and dynamic (i.e., unmodeled dynamics) uncertainty can be reduced to the case of polynomic parametric uncertainty, and thus be solved by means of the algorithm.

Sideris, Athanasios↗
NASA NTRS1994

Parametric robust control and system identification: Unified approach

Despite significant advancement in the area of robust parametric control, the problem of synthesizing such a controller is still a wide open problem. Thus, we attempt to give a solution to this important problem. Our approach captures the parametric uncertainty as an H(sub infinity) unstructured uncertainty so that H(sub infinity) synthesis techniques are applicable. Although the techniques cannot cope with the exact parametric uncertainty, they give a reasonable guideline to model the unstructured uncertainty that contains the parametric uncertainty. An additional loop shaping technique is also introduced to relax its conservatism.

Keel, Leehyun↗
NASA NTRS2008

Parametric-Studies and Data-Plotting Modules for the SOAP

"Parametric Studies" and "Data Table Plot View" are the names of software modules in the Satellite Orbit Analysis Program (SOAP). Parametric Studies enables parameterization of as many as three satellite or ground-station attributes across a range of values and computes the average, minimum, and maximum of a specified metric, the revisit time, or 21 other functions at each point in the parameter space. This computation produces a one-, two-, or three-dimensional table of data representing statistical results across the parameter space. Inasmuch as the output of a parametric study in three dimensions can be a very large data set, visualization is a paramount means of discovering trends in the data (see figure). Data Table Plot View enables visualization of the data table created by Parametric Studies or by another data source: this module quickly generates a display of the data in the form of a rotatable three-dimensional-appearing plot, making it unnecessary to load the SOAP output data into a separate plotting program. The rotatable three-dimensionalappearing plot makes it easy to determine which points in the parameter space are most desirable. Both modules provide intuitive user interfaces for ease of use.

Source record↗
NASA NTRS2008

Parametrically disciplined operation of a vibratory gyroscope

Parametrically disciplined operation of a symmetric nearly degenerate mode vibratory gyroscope is disclosed. A parametrically-disciplined inertial wave gyroscope having a natural oscillation frequency in the neighborhood of a sub-harmonic of an external stable clock reference is produced by driving an electrostatic bias electrode at approximately twice this sub-harmonic frequency to achieve disciplined frequency and phase operation of the resonator. A nearly symmetric parametrically-disciplined inertial wave gyroscope that can oscillate in any transverse direction and has more than one bias electrostatic electrode that can be independently driven at twice its oscillation frequency at an amplitude and phase that disciplines its damping to zero in any vibration direction. In addition, operation of a parametrically-disciplined inertial wave gyroscope is taught in which the precession rate of the driven vibration pattern is digitally disciplined to a prescribed non-zero reference value.

Shcheglov, Kirill V.↗
NASA NTRS2009

Ultra-Broad-Band Optical Parametric Amplifier or Oscillator

A concept for an ultra-broad-band optical parametric amplifier or oscillator has emerged as a by-product of a theoretical study in fundamental quantum optics. The study was originally intended to address the question of whether the two-photon temporal correlation function of light [in particular, light produced by spontaneous parametric down conversion (SPDC)] can be considerably narrower than the inverse of the spectral width (bandwidth) of the light. The answer to the question was found to be negative. More specifically, on the basis of the universal integral relations between the quantum two-photon temporal correlation and the classical spectrum of light, it was found that the lower limit of two-photon correlation time is set approximately by the inverse of the bandwidth. The mathematical solution for the minimum two-photon correlation time also provides the minimum relative frequency dispersion of the down-converted light components; in turn, the minimum relative frequency dispersion translates to the maximum bandwidth, which is important for the design of an ultra-broad-band optical parametric oscillator or amplifier. In the study, results of an analysis of the general integral relations were applied in the case of an optically nonlinear, frequency-dispersive crystal in which SPDC produces collinear photons. Equations were found for the crystal orientation and pump wavelength, specific for each parametric-down-converting crystal, that eliminate the relative frequency dispersion of collinear degenerate (equal-frequency) signal and idler components up to the fourth order in the frequency-detuning parameter

Strekalov, Dmitry↗
NASA NTRSDate not supplied

Informing the Space Launch System Booster Separation Initial CFD Run Matrix with Observed Parametric Sensitivity

It currently requires significant computational cost to simulate the flow physics of the booster separation event on the Space Launch System. This comes from the large parametric space in which the event occurs, as pre-separation flight conditions and separated booster core-relative trajectories can vary. Functionally removing the risk of core-booster collision mandates careful assessment of the fluid dynamics in terms of several trajectory parameters. However, simulating the entire trajectory envelope is computationally intractable given the high parametric dimension. In order to reduce the uncertainty in the resulting low-parametric-resolution aerodynamic booster separation database, a data-driven approach was developed to select which breakpoints should be studied by simulations and experiments and which should be relegated to a regression-based interpolation procedure. This technique works by simulating cases where the flow physics are most sensitive to changes in the parameters and leaving the less parametrically sensitive regions for interpolation. The result is a booster separation run matrix whose computational cost is comparable to that of previous database generations but has lower interpolation errors.

SLS↗
NASA NTRSDate not supplied

Informing the Space Launch System Booster Separation Initial CFD Run Matrix with Observed Parametric Sensitivity

It currently requires significant computational cost to simulate the flow physics of the booster separation event on the Space Launch System. This comes from the large parametric space in which the event occurs, as pre-separation flight conditions and separated booster core-relative trajectories can vary. Functionally removing the risk of core-booster collision mandates careful assessment of the fluid dynamics in terms of several trajectory parameters. However, simulating the entire trajectory envelope is computationally intractable given the high parametric dimension. In order to reduce the uncertainty in the resulting low-parametric-resolution aerodynamic booster separation database, a data-driven approach was developed to select which breakpoints should be studied by simulations and experiments and which should be relegated to a regression-based interpolation procedure. This technique works by simulating cases where the flow physics are most sensitive to changes in the parameters and leaving the less parametrically sensitive regions for interpolation. The result is a booster separation run matrix whose computational cost is comparable to that of previous database generations but has lower interpolation errors.

SLS↗
NASA NTRS2023

New Seawater Dielectric Constant Parametrization and Application to SMOS Retrieved Salinity

The accuracy of the Sea Surface Salinity (SSS) retrieved from L-Band radiometer measurements is strongly dependent on the reliability of the dielectric constant model. Two new parametrizations were recently developed based on one hand on the Soil Moisture and Ocean Salinity (SMOS) satellite multi-angular brightness temperature measurements by Boutin et al. (2021) (BV), and on the other hand, on new George Washington University laboratory measurements by Zhou et al. (2021) (GW2020). These two approaches are fully independent. For most SSS and Sea Surface Temperature (SST) conditions commonly observed over the open ocean, the relative variations of brightness temperatures Tb simulated through the BV and GW2020 parametrizations agree particularly well, and better than with earlier parametrizations previously used in the SMOS, Soil Moisture Active Passive (SMAP) and Aquarius SSS retrievals. Nevertheless, uncertainty remains, especially below 10 °C where a ∼ 0.1 K relative difference between the two models is observed. This motivates the development of a revised parameterization, BVZ, based on a methodology similar to that used to derive BV but using GW2020 instead of SMOS measurements. Compared to the GW2020 parameterization, BVZ is derived with a reduced number of degrees of freedom, it relies on the TEOS10 PSS78 conductivity-salinity relationship, and on the previously derived static permittivity of fresh water. One month per season of SMOS data have been reprocessed in 2018 using BV, GW2020, and BVZ. We find the best overall agreement between SMOS SSS and Argo SSS with BVZ parametrization, with noticeable improvement in the 5 °C–15 °C SST range.

sea measurements↗
NASA NTRS1973

Parametric analysis of ATM solar array.

The paper discusses the methods used for the calculation of ATM solar array performance characteristics and provides the parametric analysis of solar panels used in SKYLAB. To predict the solar array performance under conditions other than test conditions, a mathematical model has been developed. Four computer programs have been used to convert the solar simulator test data to the parametric curves. The first performs module summations, the second determines average solar cell characteristics which will cause a mathematical model to generate a curve matching the test data, the third is a polynomial fit program which determines the polynomial equations for the solar cell characteristics versus temperature, and the fourth program uses the polynomial coefficients generated by the polynomial curve fit program to generate the parametric data.

Singh, B. K.↗
NASA NTRS1976

Ku band low noise parametric amplifier

A low noise, K sub u-band, parametric amplifier (paramp) was developed. The unit is a spacecraft-qualifiable, prototype, parametric amplifier for eventual application in the shuttle orbiter. The amplifier was required to have a noise temperature of less than 150 K. A noise temperature of less than 120 K at a gain level of 17 db was achieved. A 3-db bandwidth in excess of 350 MHz was attained, while deviation from phase linearity of about + or - 1 degree over 50 MHz was achieved. The paramp operates within specification over an ambient temperature range of -5 C to +50 C. The performance requirements and the operation of the K sub u-band parametric amplifier system are described. The final test results are also given.

Source record↗
NASA NTRS1977

Fuel cell on-site integrated energy system parametric analysis of a residential complex

A parametric energy-use analysis was performed for a large apartment complex served by a fuel cell on-site integrated energy system (OS/IES). The variables parameterized include operating characteristics for four phosphoric acid fuel cells, eight OS/IES energy recovery systems, and four climatic locations. The annual fuel consumption for selected parametric combinations are presented and a breakeven economic analysis is presented for one parametric combination. The results show fuel cell electrical efficiency and system component choice have the greatest effect on annual fuel consumption; fuel cell thermal efficiency and geographic location have less of an effect.

Simons, S. N.↗
NASA NTRS1978

Low-noise receivers: S-band parametric up converter development

The combination of a cryogenically-cooled parametric upconverter and a higher frequency maser post amplifier was proposed as a method of achieving maser-like receiver noise temperatures over much larger instantaneous bandwidths and tuning ranges than are presently obtainable with masers in the range of 1 to 18 GHz. An experimental 2.0- to 2.5-GHz parametric upconverter/maser system was developed to explore these possibilities. Initial tests of this system resulted in an effective input noise temperature of 3.1 K at 2295 MHz and 3.2 K at 2388 MHz. The parametric upconverter logged over 1500 hours at 4.5 K and underwent 5 thermal cycles (300 K to 4.5 K to 300 K) without degradation.

Petty, S.↗
NASA NTRS1980

Parametric infrared tunable laser system

A parametric tunable infrared laser system was built to serve as transmitter for the remote detection and density measurement of pollutant, poisonous, or trace gases in the atmosphere. The system operates with a YAG:Nd laser oscillator amplifier chain which pumps a parametric tunable frequency converter. The completed system produced pulse energies of up to 30 mJ. The output is tunable from 1.5 to 3.6 micrometers at linewidths of 0.2-0.5 /cm (FWHM), although the limits of the tuning range and the narrower line crystals presently in the parametric converter by samples of the higher quality already demonstrated is expected to improve the system performance further.

Garbuny, M.↗
NASA NTRS1982

Quantiles, parametric-select density estimation, and bi-information parameter estimators

A quantile-based approach to statistical analysis and probability modeling of data is presented which formulates statistical inference problems as functional inference problems in which the parameters to be estimated are density functions. Density estimators can be non-parametric (computed independently of model identified) or parametric-select (approximated by finite parametric models that can provide standard models whose fit can be tested). Exponential models and autoregressive models are approximating densities which can be justified as maximum entropy for respectively the entropy of a probability density and the entropy of a quantile density. Applications of these ideas are outlined to the problems of modeling: (1) univariate data; (2) bivariate data and tests for independence; and (3) two samples and likelihood ratios. It is proposed that bi-information estimation of a density function can be developed by analogy to the problem of identification of regression models.

Parzen, E.↗
NASA NTRS1981

Parametric analysis of closed cycle magnetohydrodynamic (MHD) power plants

A parametric analysis of closed cycle MHD power plants was performed which studied the technical feasibility, associated capital cost, and cost of electricity for the direct combustion of coal or coal derived fuel. Three reference plants, differing primarily in the method of coal conversion utilized, were defined. Reference Plant 1 used direct coal fired combustion while Reference Plants 2 and 3 employed on site integrated gasifiers. Reference Plant 2 used a pressurized gasifier while Reference Plant 3 used a ""state of the art' atmospheric gasifier. Thirty plant configurations were considered by using parametric variations from the Reference Plants. Parametric variations include the type of coal (Montana Rosebud or Illinois No. 6), clean up systems (hot or cold gas clean up), on or two stage atmospheric or pressurized direct fired coal combustors, and six different gasifier systems. Plant sizes ranged from 100 to 1000 MWe. Overall plant performance was calculated using two methodologies. In one task, the channel performance was assumed and the MHD topping cycle efficiencies were based on the assumed values. A second task involved rigorous calculations of channel performance (enthalpy extraction, isentropic efficiency and generator output) that verified the original (task one) assumptions. Closed cycle MHD capital costs were estimated for the task one plants; task two cost estimates were made for the channel and magnet only.

Owens, W.↗
NASA NTRS1989

Definition of NASTRAN sets by use of parametric geometry

Many finite element preprocessors describe finite element model geometry with points, lines, surfaces and volumes. One method for describing these basic geometric entities is by use of parametric cubics which are useful for representing complex shapes. The lines, surfaces and volumes may be discretized for follow on finite element analysis. The ability to limit or selectively recover results from the finite element model is extremely important to the analyst. Equally important is the ability to easily apply boundary conditions. Although graphical preprocessors have made these tasks easier, model complexity may not lend itself to easily identify a group of grid points desired for data recovery or application of constraints. A methodology is presented which makes use of the assignment of grid point locations in parametric coordinates. The parametric coordinates provide a convenient ordering of the grid point locations and a method for retrieving the grid point ID's from the parent geometry. The selected grid points may then be used for the generation of the appropriate set and constraint cards.

Baughn, Terry V.↗
NASA NTRS1992

Localization of one-photon state in space and Einstein-Podolsky-Rosen paradox in spontaneous parametric down conversion

An experiment on one-photon state localization in space using a correlation technique in Spontaneous Parametric Down Conversion (SPDC) process is discussed. Results of measurements demonstrate an idea of the Einstein-Podolsky-Rosen (EPR) paradox for coordinate and momentum variables of photon states. Results of the experiment can be explained with the help of an advanced wave technique. The experiment is based on the idea that two-photon states of optical electromagnetic fields arising in the nonlinear process of the spontaneous parametric down conversion (spontaneous parametric light scattering) can be explained by quantum mechanical theory with the help of a single wave function.

Penin, A. N.↗