Search NASA⌕ Search

SEARCH · Search NASA

Results for “patch antenna”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A 10 GHz Y-Ba-Cu-O/GaAs hybrid oscillator proximity coupled to a circular microstrip patch antenna

A 10 GHz hybrid Y-Ba-Cu-O / GaAs microwave oscillator proximity coupled to a circular microstrip antenna was designed, fabricated and characterized. The oscillator was a reflection mode type using a GaAs MESFET as the active element. The feedline, transmission lines, RF chokes, and bias lines were all fabricated from YBa2Cu3O(7-x) superconducting thin films on a 1 cm x 1 cm lanthanum aluminate substrate. The output feedline of the oscillator was wire bonded to a superconducting feedline on a second 1 cm x 1 cm lanthanum aluminate substrate, which was in turn proximity coupled to a circular microstrip patch antenna. Antenna patterns from this active patch antenna and the performance of the oscillator measured at 77 K are reported. The oscillator had a maximum output power of 11.5 dBm at 77 K, which corresponded to an efficiency of 10 percent. In addition, the efficiency of the microstrip patch antenna together with its high temperature superconducting feedline was measured from 85 K to 30 K and was found to be 71 percent at 77 4 increasing to a maximum of 87.4 percent at 30 K.

Rohrer, Norman J.↗
NASA NTRS2000

Suspended Patch Antennas With Electromagnetically Coupled Inverted Microstrip Feed for Circular Polarization

The paper demonstrates a suspended nearly square patch antenna with offset feed and a square patch antenna with truncated corners for circular polarization. The antennas are excited by an electromagnetically coupled inverted microstrip feed. In addition a new transition between conventional microstrip and inverted microstrip is proposed. The measured results include the axial ratio and the impedance bandwidth of the antennas.

Simons, Rainee N.↗
NASA NTRS2008

VHF Wide-Band, Dual-Polarization Microstrip-Patch Antenna

The figure depicts selected aspects of a very-high-frequency (VHF) microstrip patch antenna designed and built to satisfy requirements specific to an airborne synthetic-aperture radar system for measuring the thickness of sea ice. One of the requirements is that the antenna be capable of functioning over the relatively wide frequency band of 127 to 172 MHz corresponding to a fractional bandwidth of about 30 percent relative to a nominal mid-band frequency of 149.5 MHz. Another requirement is that the antenna be capable of functioning in either or both of two orthogonal linear polarizations. In addition, the antenna is required to be as compact and lightweight as possible. In a basic design according to generally accepted microstrip-patch-antenna engineering practice, one would ordinarily use a relatively thick dielectric substrate and multiple feed probes to obtain the desired combination of wide-band and dual-polarization capabilities. However, the combination of a thick substrate and multiple feeds would give rise to higher-order electromagnetic nodes, thereby undesirably contributing to cross polarization and to reduction of the isolation between feed probes. To counter these adverse effects while satisfying the requirements stated above, the design of this antenna incorporates several improvements over the basic design.

Huang, John↗
NASA NTRS1991

A 29.3-GHz cavity-enclosed aperture-coupled circular-patch antenna for microwave circuit integration

A circular patch antenna fed by an aperture-coupled microstrip line has been demonstrated at 29.3 GHz. The patch was enclosed by a cavity to reduce surface-wave interactions in an array environment and to improve heat dissipation when using active devices. The antenna exhibited a 2:1 input VSWR (voltage standing wave ratio) over a bandwidth of 12 percent from 27.52 to 30.95 GHz. The antenna should have applications in conformal phased arrays at millimeter-wave frequencies.

Navarro, Julio A.↗
NASA NTRS1994

Analysis of cylindrical wrap-around and doubly conformal patch antennas by way of the finite element-artificial absorber method

The goal of this project was to develop analysis codes for computing the scattering and radiation of antennas on cylindrically and doubly conformal platforms. The finite element-boundary integral (FE-BI) method has been shown to accurately model the scattering and radiation of cavity-backed patch antennas. Unfortunately extension of this rigorous technique to coated or doubly curved platforms is cumbersome and inefficient. An alternative approximate approach is to employ an absorbing boundary condition (ABC) for terminating the finite element mesh thus avoiding use of a Green's function. A FE-ABC method is used to calculate the radar cross section (RCS) and radiation pattern of a cavity-backed patch antenna which is recessed within a metallic surface. It is shown that this approach is accurate for RCS and antenna pattern calculations with an ABC surface displaced as little as 0.3 lambda from the cavity aperture. These patch antennas may have a dielectric overlay which may also be modeled with this technique.

Volakis, J. L.↗
NASA NTRS1994

Analysis of a Slot Coupled Coplanar Waveguide Fed Patch Antenna

A slot-coupled CPW fed patch antenna is analyzed using two different techniques: the Spectral Domain Method and the Finite Difference Time Domain Method. The results from both techniques are in good agreement with experimentally obtained data.

Cheng, Jui-Ching↗
NASA NTRS2004

Measuring Radiation Patterns of Reconfigurable Patch Antennas on Wafers

An apparatus and technique have been devised for measuring the radiation pattern of a microwave patch antenna that is one of a number of identical units that have been fabricated in a planar array on a high-resistivity silicon wafer. The apparatus and technique are intended, more specifically, for application to such an antenna that includes a DC-controlled microelectromechanical system (MEMS) actuator for switching the antenna between two polarization states or between two resonance frequencies. Prior to the development of the present apparatus and technique, patch antennas on wafers were tested by techniques and equipment that are more suited to testing of conventional printed-circuit antennas. The techniques included sawing of the wafers to isolate individual antennas for testing. The equipment included custom-built test fixtures that included special signal launchers and transmission-line transitions. The present apparatus and technique eliminate the need for sawing wafers and for custom-built test fixtures, thereby making it possible to test antennas in less time and at less cost. Moreover, in a production setting, elimination of the premature sawing of wafers for testing reduces loss from breakage, thereby enhancing yield.

Simons, Rainee N.↗
NASA NTRS2002

Novel On-wafer Radiation Pattern Measurement Technique for MEMS Actuator Based Reconfigurable Patch Antennas

The paper presents a novel on-wafer, antenna far field pattern measurement technique for microelectromechanical systems (MEMS) based reconfigurable patch antennas. The measurement technique significantly reduces the time and the cost associated with the characterization of printed antennas, fabricated on a semiconductor wafer or dielectric substrate. To measure the radiation patterns, the RF probe station is modified to accommodate an open-ended rectangular waveguide as the rotating linearly polarized sampling antenna. The open-ended waveguide is attached through a coaxial rotary joint to a Plexiglas(Trademark) arm and is driven along an arc by a stepper motor. Thus, the spinning open-ended waveguide can sample the relative field intensity of the patch as a function of the angle from bore sight. The experimental results include the measured linearly polarized and circularly polarized radiation patterns for MEMS-based frequency reconfigurable rectangular and polarization reconfigurable nearly square patch antennas, respectively.

Simons, Rainee N.↗
NASA NTRS2004

Suspended-Patch Antenna With Inverted, EM-Coupled Feed

An improved suspended-patch antenna has been designed to operate at a frequency of about 23 GHz with linear polarization and to be one of four identical antennas in a rectangular array. The antenna includes a parasitic patch on top of a suspended dielectric superstrate, an active patch on top of a suspended dielectric substrate, a microstrip on the bottom of the dielectric substrate, and a ground plane. The microstrip, the ground plane, the airgap between them, and the dielectric substrate together constitute a transmission line that has an impedance of 50 Ohm and is electromagnetically (EM) coupled to the active patch. The parasitic patch is, in turn, excited by the active patch. The microstrip feed is characterized as inverted because the microstrip is on the bottom of the substrate, whereas microstrips are usually placed on the tops of dielectric substrates

Simons, Rainee N.↗
NASA NTRS1992

Scattering from arbitrarily shaped microstrip patch antennas

The scattering properties of arbitrarily shaped microstrip patch antennas are examined. The electric field integral equation for a current element on a grounded dielectric slab is developed for a rectangular geometry based on Galerkin's technique with subdomain rooftop basis functions. A shape function is introduced that allows a rectangular grid approximation to the arbitrarily shaped patch. The incident field on the patch is expressed as a function of incidence angle theta(i), phi(i). The resulting system of equations is then solved for the unknown current modes on the patch, and the electromagnetic scattering is calculated for a given angle. Comparisons are made with other calculated results as well as with measurements.

Shively, David G.↗
NASA NTRS2012

Single-Layer, All-Metal Patch Antenna Element with Wide Bandwidth

It is known that the impedance at the center of a patch antenna element is a short circuit, implying that a wire or post can be connected from the patch to the groundplane at this point without impacting radiation performance. In principle, this central post can be used to support the patch element, thus eliminating the need for dielectric. In spaceborne applications, this approach is problematic because a patch element supported by a single, thin post is highly susceptible to acoustic loads during launch. The technology reported here uses a large-diameter center post as its supporting structure. The supporting structure allows for the fabrication of a sufficiently rigid antenna element that can survive launch loads. The post may be either hollow or solid, depending on fabrication approach and/or mass constraints. The patch antenna element and support post are envisioned as being fabricated (milled) from a single piece of aluminum or other metal. Alternately, the patch plate and support column can be fabricated separately and then joined using fasteners, adhesive, or welding. Casting and electroforming are also viable techniques for manufacturing the metal patch part(s). The patch structure is then either bonded or fastened to the supporting groundplane. Arrays of patch elements can be fabricated by attaching several structures to a common groundplane/support structure.

Chamberlain, Neil F.↗
NASA NTRS2005

Patch Antenna Fed via Unequal-Crossed-Arm Aperture

A proposed rectangular-patch antenna for transmitting or receiving microwave circularly polarized (CP) radiation would be fed via a cross-shaped aperture that would have unequal arms and would, in turn, be fed at a single point via a microstrip transmission line. As a consequence of the unequal-arm aperture design, the antenna could be made smaller in one dimension, relative to a typical prior CP antenna that comprises a nearly square patch fed via an equal-crossed-arm aperture. Hence, in designing a phased array of such antennas, the antennas could be packed together more closely along one dimension, making it possible to scan the beam radiated by the antenna over a wider angular range in a plane that includes that dimension. Alternatively or in addition, one could lay out transmission lines in the extra spaces created by the shortening in one dimension

Epp, Larry↗
NASA NTRS1988

Crosspolarisation characteristics of rectangular patch antennas

Theoretical results describing the crosspolarization characteristics of rectangular patch antennas are presented. Of particular interest is the result that the copolarization radiation is not sensitive to resonant frequency and substrate thickness while the crosspolarization component increases with resonant frequency and/or substrate thickness.

Huynh, T.↗
NASA NTRS1997

Feasibility Study of Optically Transparent Microstrip Patch Antenna

The paper presents a feasibility study on optically transparent patch antennas with microstrip line and probe feeds. The two antennas operate at 2.3 GHz and 19.5 GHz respectively. They are constructed from a thin sheet of clear polyester with an AgHT-8 optically transparent conductive coating. The experimental results show good radiation patterns and input impedance match. The antennas have potential applications in mobile wireless communications.

Simons, Rainee N.↗
NASA NTRS1997

Feasibility Study of Optically Transparent Microstrip Patch Antenna

The paper presents a feasibility study on optically transparent patch antennas with microstrip line and probe feeds. The two antennas operate at 2.3 GHz and 19.5 GHz respectively. They are constructed from a thin sheet of clear polyester with an AgHT-8 optically transparent conductive coating. The experimental results show good radiation patterns and input impedance match. The antennas have potential applications in mobile wireless communications.

Simons, Rainee N.↗
NASA NTRS1993

Analysis of microstrip patch antennas with nonzero surface resistance

The scattering properties of a microstrip patch antenna with nonzero surface impedance are examined. The electric field integral equation for a current element on a grounded dielectric slab is developed for a rectangular geometry by using Galerkin's technique with subdomain piecewise linear basis functions. The integral equation includes a resistive boundary condition on the surface of the patch. The incident field on the patch is expressed as a function of incidence angle. The resulting system of equations is then solved for the unknown current modes on the patch, and the radar cross section is calculated for a given scattering angle. Theoretical results in the form of radar cross section as a function of frequency are compared with results measured at the NASA Langley Research Center.

Shively, David G.↗
NASA NTRS1992

A scheme to alter the resonant frequency of the microstrip patch antenna

Simple schemes are presented for altering the resonant frequency of a rectangular patch antenna without the need to change its size. In particular, by placing a perturbance below the patch it is shown that as much as 20 percent increase and 30 percent decrease from the resonant frequency of the unperturbed patch can be achieved. The specific configurations considered in this letter include a cavity-backed, aperture-backed, and protrusion-backed patch, and for each case design curves are presented.

Volakis, John L.↗