Search NASA⌕ Search

SEARCH · Search NASA

Results for “performance shaping factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Vortex Generators in a Two-Dimensional, External-Compression Supersonic Inlet

Vortex generators within a two-dimensional, external-compression supersonic inlet for Mach 1.6 were investigated to determine their ability to increase total pressure recovery, reduce total pressure distortion, and improve the boundary layer. The vortex generators studied included vanes and ramps. The geometric factors of the vortex generators studied included height, length, spacing, and positions upstream and downstream of the inlet terminal shock. The flow through the inlet was simulated through the computational solution of the steady-state Reynolds-averaged Navier-Stokes equations on multi-block, structured grids. The vortex generators were simulated by either gridding the geometry of the vortex generators or modeling the vortices generated by the vortex generators. The inlet performance was characterized by the inlet total pressure recovery, total pressure distortion, and incompressible shape factor of the boundary-layer at the engine face. The results suggested that downstream vanes reduced the distortion and improved the boundary layer. The height of the vortex generators had the greatest effect of the geometric factors.

computational fluid dynamics↗
NASA NTRSDate not supplied

Benefit and Critical Factors for the Performance of the Boundary Layer Ingesting Propulsion

The benefit of the boundary layer ingestion (BLI) is described in the perspective of the propulsion and engine development. A power saving map of the BLI engines is derived based on the correlation of the shape factor of the ingested boundary layer and the propulsive efficiency. The ratio of the mass flow rate between BLI and non-BLI propulsors is introduced to quantify the power saving of the BLI engine relative to a corresponding clean inlet flow engine that generates the same amount of net thrust. The wake recovery factor from the jet flow is applied to find the optimum sizing of the engine for the given design requirement. The effects of the fan pressure ratio of the propulsor toward the power saving are also investigated to seek out the feasible range of the BLI propulsor design. The derived correlation is validated with CFD analyses. Simulation models using variously sized engines relative to an influencing body are developed so that a numerical experiment is carried out with the various shape factors. The effect of the propulsion airframe integration toward the aerodynamic forces on the fuselage and nacelle is investigated via parametric study of the engine sizing and fan pressure ratio for the wake ingestion models. The propulsor efficiency is quantified toward the saving in the actual shaft power and correlated with the efficiency penalty of the BLI propulsor. The correlation is also validated via comparison of the turbo-machinery CFD results for BLI2DTF and conventional transonic fan stages.

Boundary Layer Ingestion↗
NASA NTRS1986

Input-current shaped ac to dc converters

The problem of achieving near unity power factor while supplying power to a dc load from a single phase ac source of power is examined. Power processors for this application must perform three functions: input current shaping, energy storage, and output voltage regulation. The methods available for performing each of these three functions are reviewed. Input current shaping methods are either active or passive, with the active methods divided into buck-like and boost-like techniques. In addition to large reactances, energy storage methods include resonant filters, active filters, and active storage schemes. Fast voltage regulation can be achieved by post regulation or by supplementing the current shaping topology with an extra switch. Some indications of which methods are best suited for particular applications concludes the discussion.

Source record↗
NASA NTRSDate not supplied

Spacesuit and Mobility Performance Changes

The complex interactions between the human body and spacesuit lead to changes inmovement patterns and mobility performancesof the wearer. In general, factors including the geometric properties, such as shape and size, mechanical properties of the suit, and pressurization of the suit are known to be associated with altered movement patterns as compared to an unsuited human.However, their relative contributions have not been explicitly quantified from the mobility performance perspectives. The goal of this study wasthus to assessthe effects fromthe different types of mobility constraintconditions, namely by wearing either a 3D printed hard upper torso (HUT) assembly orfully pressurized spacesuit. The outcome was also compared against the unsuited motions. For this study, an xEMU (exploration Extravehicular Mobility Unit) suitwas considered, which is the next generation spacesuit developed by NASA. In each test condition, the subject was asked to move the arm and hand as prescribedfor different task types, and the corresponding body segment locations were recordedusing a 3D motion capture system. The following three tasks were performedand analyzed: 1) Outward one-handed reaches:the subject in a standing pose made sweeping motions with the extended right arm from the extreme end-to-end positions, including side-to-side at different elevations and top-to-bottom at different azimuths. 2) Outward two-handed reaches:similarto the previous task, howeverthe subject kept the hands together during the motions in order to assessthe areas that can be reached by both hands. 3) Inward one-handed reaches:the subject made right-hand reach motions to the surface of the HUT.The hand traces collected from each task were modeled by a template shape parametrically deformed with a radial basis function. This process enabled foran abstraction of the hand traces into a smooth surface envelope representing the maximally reachable area of the test subject, of which the shapes and sizes were compared across the different test conditions. The preliminary analysis has shown that theoverall size of reachenvelopes decreases in a pressurized suit compared to 3D printed mockup HUT and unsuited conditions. The specific shape of the envelopes, which were determined by the reachable and unreachable zones, alsovary with the testconditions, and the differences werepronounced with the inward reaches to the HUT surface. The latter observation ispotentially relatedto the increased demandfor shoulder and elbow flexions.Overcomingthe resistance from the pressurizedsoft goods and mechanical constraints of the shoulder assemblywas seen to be associated with the difference in motion patterns between the suited and unsuited conditions. Overall, the information quantified from this study is expected to provide structured metrics for spacesuit mobility, which can improve design optimization and human-system integration.

K Han Kim↗
NASA NTRS2017

Wavefront Control Performance Modeling with WFIRST Shaped Pupil Coronagraph Testbed

NASA’s WFIRST mission includes a coronagraph instrument (CGI) for direct imaging of exoplanets. Significant improvement in CGI model fidelity has been made recently, alongside a testbed high contrast demonstration in a simulated dynamic environment at JPL. We present our modeling method and results of comparisons to testbed’s high order wavefront correction performance for the shaped pupil coronagraph. Agreement between model prediction and testbed result at better than a factor of 2 has been consistently achieved in raw contrast (contrast floor, chromaticity, and convergence), and with that comes good agreement in contrast sensitivity to wavefront perturbations and mask lateral shear.

Zhou, Hanying↗
NASA NTRS1982

Optimization of Dish Solar Collectors with and without Secondary Concentrators

Methods for optimizing parabolic dish solar collectors and the consequent effects of various optical, thermal, mechanical, and cost variables are examined. The most important performance optimization is adjusting the receiver aperture to maximize collector efficiency. Other parameters that can be adjusted to optimize efficiency include focal length, and, if a heat engine is used, the receiver temperature. The efficiency maxima associated with focal length and receiver temperature are relatively broad; it may, accordingly, be desirable to design somewhat away from the maxima. Performance optimization is sensitive to the slope and specularity errors of the concentrator. Other optical and thermal variables affecting optimization are the reflectance and blocking factor of the concentrator, the absorptance and losses of the receiver, and, if a heat engine is used, the shape of the engine efficiency versus temperature curve. Performance may sometimes be improved by use of an additional optical element (a secondary concentrator) or a receiver window if the errors of the primary concentrator are large or the receiver temperature is high.

Jaffe, L. D.↗
NASA NTRS1983

Optimization of dish solar collectors

Methods for optimizing parabolic dish solar collectors and the consequent effects of various optical, thermal, mechanical, and cost variables are examined. The most important performance optimization is adjusting the receiver aperture to maximize collector efficiency. Other parameters that can be adjusted to optimize efficiency include focal length, and, if a heat engine is used, the receiver temperature. The efficiency maxima associated with focal length and receiver temperature are relatively broad; it may, accordingly, be desirable to design somewhat away from the maxima. Performance optimization is sensitive to the slope and specularity errors of the concentrator. Other optical and thermal variables affecting optimization are the reflectance and blocking factor of the concentrator, the absorptance and losses of the receiver, and, if a heat engine is used, the shape of the engine efficiency versus temperature curve. Performance may sometimes be improved by use of an additional optical element (a secondary concentrator) or a receiver window if the errors of the primary concentrator are large or the receiver temperature is high. Previously announced in STAR as N83-19224

Jaffe, L. D.↗
NASA NTRS1991

Modal identification experiment design for large space structures

This paper describes an on-orbit modal identification experiment design for large space structures. Space Station Freedom (SSF) systems design definition and structural dynamic models were used as representative large space structures for optimizing experiment design. Important structural modes of study models were selected to provide a guide for experiment design and used to assess the design performance. A pulsed random excitation technique using propulsion jets was developed to identify closely-spaced modes. A measuremenat location selection approach was developed to estimate accurate mode shapes as well as frequencies and damping factors. The data acquisition system and operational scenarios were designed to have minimal impacts on the SSF. A comprehensive simulation was conducted to assess the overall performance of the experiment design.

Kim, Hyoung M.↗
NASA NTRS1988

Scattering from nonspherical Chebyshev particles. II - Means of angular scattering patterns

The calculated angular scattering properties of over 250 randomly oriented nonspherical Chebyshev particles are examined for the effect of three factors: size; concavity vs convexity; and amount of deformation from a sphere. Both shape and size averaging are performed to reveal general features of the angular scattering not discernible for particular shapes and sizes. Comparisons with a comparably extensive experimental study published by Zerull in 1976 reveal remarkable qualitative similarities, even though Zerull used greatly different shapes from ours. This augurs well for the eventual development of a general theory of nonspherical scattering, although such a theory must account for concavity in addition to the amount of deviation from a sphere; and it cannot be entirely deterministic, as the third paper in this series will argue.

Wiscombe, Warren J.↗
NASA NTRS1993

Asynchronous timing and Doppler recovery in DSP based DPSK modems for fixed and mobile satellite applications

While conventional analog modems employ some kind of clock wave regenerator circuit for synchronous timing recovery, in sampled modem receivers the timing is recovered asynchronously to the incoming data stream, with no adjustment being made to the input sampling rate. All timing corrections are accomplished by digital operations on the sampled data stream, and timing recovery is asynchronous with the uncontrolled, input A/D system. A good timing error measurement algorithm is a zero crossing tracker proposed by Gardner. Digital, speech rate (2400 - 4800 bps) M-PSK modem receivers employing Gardner's zero crossing tracker were implemented and tested and found to achieve BER performance very close to theoretical values on the AWGN channel. Nyguist pulse shaped modem systems with excess bandwidth factors ranging from 100 to 60 percent were considered. We can show that for any symmetric M-PSK signal set Gardner's NDA algorithm is free of pattern jitter for any carrier phase offset for rectangular pulses and for Nyquist pulses having 100 percent excess bandwidth. Also, the Nyquist pulse shaped system is studied on the mobile satellite channel, where Doppler shifts and multipath fading degrade the pi/4-DQPSK signal. Two simple modifications to Gardner's zero crossing tracker enable it to remain useful in the presence of multipath fading.

Koblents, B.↗
NASA NTRS2011

Seating Considerations for Spaceflight: The Human to Machine Interface

Seating is one of the most critical components to be considered during design of a spacecraft. Since seats are the final interface between the occupant and the vehicle wherein all launch and landing operations are performed, significant effort must be spent to ensure proper integration of the human to the spacecraft. The importance of seating can be divided into two categories: seat layout and seat design. The layout of the seats drives the overall cabin configuration - from displays and controls, to windows, to stowage, to egress paths. Since the layout of the seats is such a critical design parameter within the crew compartment, it is one of the first design challenges that must be completed in the critical path of the spacecraft design. In consideration of seat layout in the vehicle, it is important for the designers to account for often intangible factors such as safety, operability, contingency performance, crew rescue. Seat layout will lead to definition of the quantity, shape, and posture of the seats. The seats of the craft must restrain and protect the occupant in all seated phases of flight, while allowing for nominal mission performance. In design of a spacecraft seat, the general posture of the occupant and the landing loads to be encountered are the greatest drivers of overall design. Variances, such as upright versus recumbent postures will dictate fit of the seat to the occupant and drive the total envelope of the seat around the occupant. Seat design revolves around applying sound principles of seated occupant protection coupled with the unique environments driven by the seat layout, landing loads, and operational and emergency scenarios.

Gohmert, Dustin M.↗
NASA NTRS1991

Influence of a magnetic field during directional solidification of MAR-M 246 + Hf superalloy

An area that has been almost totally overlooked in the optimization of properties in directionally solidified superalloys is the control of microstructural features through the application of a magnetic field during solidification. The influence of a magnetic field on the microstructural features of a nickel-base superalloys is investigated. Studies were performed on the dendritic MAR-M 246+Hf alloy, which was solidified under both a 5 K gauss magnetic field and under no-applied-field conditions. The possible influences of the magnetic field on the solidification process were observed by studying variations in microstructural features including volume fraction, surface area, number, and shape of the carbide particles. Stereological factors analyzed also included primary and secondary dendrite arm spacing and the volume fraction of the interdendritic eutectic constituent. Microprobe analysis was performed to determine the chemistry of the carbides, dendrites, and interdendritic constituents, and how it varied between field and no-field solidification samples. Experiments involving periodic application and removal of the magnetic field were also performed in order to permit a comparison with structural variations observed in a MAR-M 246+Hf alloy solidified during KC-135 high-g, low-g maneuvers.

Andrews, J. Barry↗
NASA NTRS2011

Aerodynamic Simulation of Ice Accretion on Airfoils

This report describes recent improvements in aerodynamic scaling and simulation of ice accretion on airfoils. Ice accretions were classified into four types on the basis of aerodynamic effects: roughness, horn, streamwise, and spanwise ridge. The NASA Icing Research Tunnel (IRT) was used to generate ice accretions within these four types using both subscale and full-scale models. Large-scale, pressurized windtunnel testing was performed using a 72-in.- (1.83-m-) chord, NACA 23012 airfoil model with high-fidelity, three-dimensional castings of the IRT ice accretions. Performance data were recorded over Reynolds numbers from 4.5 x 10(exp 6) to 15.9 x 10(exp 6) and Mach numbers from 0.10 to 0.28. Lower fidelity ice-accretion simulation methods were developed and tested on an 18-in.- (0.46-m-) chord NACA 23012 airfoil model in a small-scale wind tunnel at a lower Reynolds number. The aerodynamic accuracy of the lower fidelity, subscale ice simulations was validated against the full-scale results for a factor of 4 reduction in model scale and a factor of 8 reduction in Reynolds number. This research has defined the level of geometric fidelity required for artificial ice shapes to yield aerodynamic performance results to within a known level of uncertainty and has culminated in a proposed methodology for subscale iced-airfoil aerodynamic simulation.

Broeren, Andy P.↗
NASA NTRSDate not supplied

Identifying Outside Influences as Latent Factors to Risk in Human Performance

During the Acquisition Life Cycle for a program, there are several opportunities for the system in design to be adjusted in accordance with its changing landscape as it is being shaped by evolving policy and organizational culture. Human Systems Integration is integral to identifying these opportunities of change as there are a set number of activities that may account for altered operational states, human performance deviations, and overall component engagement if HSI is enacted early enough in the life cycle. Some changes that occur in the operational environment may not be accounted for since the organizational culture and practices are not currently a part of the HSI focus. Likewise, policy changes themselves from a top-to-bottom analysis may not have the appearance of effecting human performance until having gone through a trail-and-error period. Workarounds to adjust for unforeseen policy affects become the system's solution that usually includes changes in the training and education of the operators, maintainers, and support personnel. A system full of workarounds and off-normal practices, that cause operators to disregard the purpose of the design, coupled with the false notion that these activities are proven for successful system operation, is the very definition of “an accident waiting to happen”. Unforeseen changes in policies and practices that cause new and unusual activities to successfully and keep the system running, should be considered latent factors that may cause a potential mishap, and not part of the resilience that humans provide to the successful operation of the system. This presentation will explore how latent factors may find their way into system operations and how they can be identified and addressed.

Human Systems Integration↗
NASA NTRS1987

Telepresence master glove controller for dexterous robotic end-effectors

This paper describes recent research in the Aerospace Human Factors Research Division at NASA's Ames Research Center to develop a glove-like, control and data-recording device (DataGlove) that records and transmits to a host computer in real time, and at appropriate resolution, a numeric data-record of a user's hand/finger shape and dynamics. System configuration and performance specifications are detailed, and current research is discussed investigating its applications in operator control of dexterous robotic end-effectors and for use as a human factors research tool in evaluation of operator hand function requirements and performance in other specialized task environments.

Fisher, Scott S.↗
NASA NTRS1983

Experimental implementation of parameter adaptive control on a free-free beam

A method for identifying modal parameters has been integrated with a modal control scheme and implemented on an experimental beam at the NASA Langley Research Center. This work is the culmination of several studies to develop adaptive control schemes for large flexible spacecraft. The identification scheme is an equation-error technique which generates modal frequency and damping estimates on-line from a set of distributed displacement measurements. The control law is a modal pole placement technique with the objective of vibration suppression. Integration of the identification and control schemes is achieved through a series of tests which validate the identified parameters before they are used for control gain updating. Results using a low order controller show that control gains can be updated in real time based on the validated parameters to improve the performance of the closed loop system. Important factors in the implementation are the test criterion and the a priori assumption of mode shapes.

Williams, J. P.↗
NASA NTRS1994

Navier-Stokes Calculations for a Highly-Twisted Rotor Near Stall

The viscous flow field near the surface of a hovering rotor blade was studied for blade twist distributions typical of a till rotor blade and a conventional helicopter rotor blade. Three blade geometries were studied, including a tilt rotor blade twist distribution (baseline), conventional helicopter rotor blade twist distribution, and the baseline twist distribution with 2 deg of precone. The results give insight into the delayed stall phenomenon often observed for highly twisted rotors. Calculations were performed for a high thrust condition near stall using the thin-layer Navier-Stokes CFD code TURNS. Effects of built-in twist on section force coefficients, skin friction, velocities, surface pressures, and boundary layer shape factor are discussed. Although the rotor thrust coefficient was nominally the same for the cases using the two twist distributions, large differences were found in the section in-plane and normal force coefficients. These preliminary results imply that the blade outboard region, rather than the inboard region, provides the majority of the performance advantage of the baseline case over the low twist case. Skin friction, velocities near the blade, and surface pressures for the two twist distributions reveal significant differences in the blade outboard region.

Yamauchi, Gloria K.↗