Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase stability modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

A systematic plan for the continued study of dimensional stability of metallic alloys considered for the fabrication of cryogenic wind tunnel models

Interrelated research and development activities, phased development of stepped specimen program are documented and a sequence for a specific program of machining, validation and heat treatment cycles for one material are described. Proposed work for the next phase of dimensional stability research is presented and further technology development activities are proposed.

Wigley, D. A.↗
NASA NTRS1987

Effect of Gimbal friction modeling technique on control stability and performance for Centaur upper-stage

The powered-phase autopilot for the Centaur upper stage rocket uses an autopilot forward loop gain scheduler that decreases the proportional gain as propellant mass is depleted. Nonlinear time response simulation studies revealed that Centaur vehicles with low-gain autopilots would have large attitude error limit cycles. These limit cycles were due to the assumed presence of Coulomb friction in the engine gimbals. This situation could be corrected through the use of an harmonic dither, programmed into the on-board digital computer and added to the engine command signal. This would introduce impending motion to the engines, allowing control of the engines even under small commands. Control authority was found to be restored when dither was used. A concern arose that the Centaur could be unacceptably excited at resonances near the dither frequency, if the dither amplitude was to be chosen on the basis of friction level present, a test was conducted to measure this level. Dither characteristics were to be based on the test results. The test results showed that the gimbal friction characteristic was actually hysteretic rather than the assumed Coulomb friction. The simulation results showed that, using this new model of gimbal friction, dither would no longer be necessary.

Graham, Ronald E.↗
NASA NTRS1991

Transient nucleation in glasses

Nucleation rates in condensed systems are frequently not at their steady state values. Such time dependent (or transient) nucleation is most clearly observed in devitrification studies of metallic and silicate glasses. The origin of transient nucleation and its role in the formation and stability of desired phases and microstructures are discussed. Numerical models of nucleation in isothermal and nonisothermal situations, based on the coupled differential equations describing cluster evolution within the classical theory, are presented. The importance of transient nucleation in glass formation and crystallization is discussed.

Kelton, K. F.↗
NASA NTRSDate not supplied

Density Variations as a Function of Compostion in the Venusian Crust: Implications for Tesserae Formation

The Venusian surface plains are thought to be predominantly basaltic, while tesserae occupy ~ 7 % and are potentially the oldest units preserved [1]. They consist of layered, folded, and eroded rocks [2], potentially giving an insight into what tectonic regimes were present during Venus’ history. Studies of the tesserae have noted lower emissivity measurements compared to the surrounding plains [3]. Several explanations for these lower emissivity values have been proposed, including a more felsic composition for the tesserae [4], that the lower emissivity could be a result of a difference in mineralogy caused by chemical weathering facilitated between the rocks and atmosphere by the lower temperatures at the higher elevations of tesserae [5]. Alternatively, the morphology of some features on tesserae, such as the Ovda Fluctus, are more consistent with a basaltic composition [6]. The presence of significant amounts of felsic igneous compositions could either imply partial melting of hydrous material and hence a higher water content in early Venus [7], or differentiation of basaltic melts [8]. Further, tesserae composition influences the density of the crust with major implications for the stability of crustal roots. Here, we use thermodynamic modeling to compute phase diagrams and extract rock densities for two end-member compositions: a basalt and a granite. We discuss major phase and density changes for each composition and describe the effect of compositional variations along geothermal gradients with implications for the stability of crustal roots with the aim to provide constraints on the composition of tesserae.

A R Baker↗
NASA NTRS1982

A structure function representation theorem with applications to frequency stability estimation

Random processes with stationary nth differences serve as models for oscillator phase noise. A theorem which obtains the structure function (covariance of the nth differences) of such a process in terms of the differences of a single function of one time variable is proven. In turn, this function can easily be obtained from the spectral density of the process. The theorem is used for computing the variance of two estimators of frequency stability.

Greenhall, C. A.↗
NASA NTRS1983

A structure function representation theorem with applications to frequency stability estimation

Random processes with stationary nth differences serve as models for oscillator phase noise. The theorem proved here allows one to obtain the structure function (covariances of the nth differences) of such a process in terms of the differences of a single function of one time variable. In turn, this function can easily be obtained from the spectral density of the process. The theorem is used for computing the variance of two estimators of frequency stability.

Greenhall, C. A.↗
NASA NTRS1980

Ion chemistry in interstellar space

The temperature dependence of the bimolecular reactions of Cl(+), HCl(+), CH(+), CH2(+), N(+), NH(+), and NH2(+) reacting with H2 have been investigated. For Cl(+) and HCl(+) rate constants have been determined over the temperature range of 150 to 400 K. Preliminary data have been obtained for the other systems. The Cl(+)/H2 system shows a weak, but significant positive temperature dependence that could be important in interstellar modeling studies. The HCl(+)/H2 system shows a substantial negative temperature dependence with the rate constant approaching the collision rate at low temperatures. The association reaction CH3(+) + HCN yields CH3 HCN(+) has been theoretically modeled using statistical phase space theory. Both radiative and collisional stabilization have been included. The results are compared with experiment with good agreement obtained over wide variations in T and p. This system is potentially important in the mechanism of large molecule synthesis in interstellar space.

Bowers, M. T.↗
NASA NTRS1999

Materials Science Experiments on the International Space Station

The Performance Goal for NASA's Microgravity Materials Science Program reads "Use microgravity to establish and improve quantitative and predictive relationships between the structure, processing and properties of materials." The advent of the International Space Station will open up a new era in Materials Science Research including the ability to perform long term and frequent experiments in microgravity. As indicated the objective is to gain a greater understanding of issues of materials science in an environment in which the force of gravity can be effectively switched off. Thus gravity related issues of convection, buoyancy and hydrostatic forces can be reduced and the science behind the structure/processing/properties relationship can more easily be understood. The specific areas of research covered within the program are (1) the study of Nucleation and Metastable States, (2) Prediction and Control of Microstructure (including pattern formation and morphological stability), (3) Phase Separation and Interfacial Stability, (4) Transport Phenomena (including process modeling and thermophysical properties measurement), and (5) Crystal Growth, and Defect Generation and Control. All classes of materials, including metals and alloys, glasses and ceramics, polymers, electronic materials (including organic and inorganic single crystals), aerogels and nanostructures, are included in these areas. The principal experimental equipment available to the materials scientist on the International Space Station (ISS) will be the Materials Science Research Facility (MSRF). Each of these systems will be accommodated in a single ISS rack, which can operate autonomously, will accommodate telescience operations, and will provide real time data to the ground. Eventual plans call for three MSRF racks, the first of which will be shared with the European Space Agency (ESA). Under international agreements, ESA and other partners will provide some of the equipment, while NASA covers launch and integration costs. The MSRF facilities will include modular components, which can be exchanged to provide inserts specifically matched to the engineering requirements of the particular Principal Investigator. To defray costs and avoid duplication of engineering effort NASA is also pursuing the possibility of using facilities provided by international partners. By this means it is anticipated that all of the types of research outlined in the previous paragraph can be done on the ISS.

Gillies, Donald C.↗
NASA NTRS2002

Chandra Discovery of Luminous Supersoft X-Ray Sources in M81

A Chandra ACIS-S imaging observation of the nearby galaxy M81 (NGC 3031) reveals 9 luminous soft X-ray sources. The local environments, X-ray spectral properties, and X-ray light curves of the sources are presented and discussed in the context of prevailing physical models for supersoft sources. It is shown that the sample falls within expectations based on population synthesis models taken from the literature though the high observed luminosities (L approx.2e36 to approx.3e38 ergs in the 0.2--2.0-keV band) and equivalent blackbody temperatures (T approx.40 to 80 eV) place the brightest detected M81 objects at the high luminosity end of the class of supersoft sources defined by previous ROSAT and Einstein studies of nearby galaxies. This is interpreted as a natural consequence of the higher sensitivity of Chandra to hotter and more luminous systems. Most of the sources can be explained as canonical supersoft sources, secreting white dwarfs powered by steady surface nuclear burning, with X-ray spectra well-fit by hot white dwarf local thermodynamic equilibrium atmosphere models. An exceptionally bright source is scrutinized in greater detail as its estimated barometric luminosity, L approx. 1.5e39 ergs, greatly exceeds theoretical estimates for supersoft sources. This source may be beyond the stability limit and undergoing a phase of mass outflow under extreme conditions. Alternatively, a model in which the observed X-ray spectrum arises from an accretion disk around a blacklists of mass approx.1200/sqrt(cosi) solar masses (viewed at an inclination angle 1) cannot be excluded.

Swartz, Douglas A.↗
NASA NTRS1991

On the dependence of travelling wave stability on basic state wave phase speed

The dependence of stability on basic state wave phase speed is examined in a nondivergent barotropic model on a sphere for planetary scale waves with phase speeds typical of waves observed in the atmosphere. Triad interactions are examined analytically and compared to numerical results from a full spectral model. A number of triads may result in growth of the perturbation components for each basic state wave; for each triad there is a basic state wave phase speed where it is resonant, identified as the point where the critical amplitude for instability to that perturbation becomes zero. Critical amplitudes for instability obtained using the full spectral model generally agree well with triad results. Since the basic state wave phase speed determines which triad will grow, spatial structure and critical amplitudes for instability for the growing disturbances depend strongly on basic state wave phase speed. The results of this idealized study suggest that phase speed may be an important factor in determining the stability of planetary scale waves in the atmosphere.

Manney, Gloria L.↗
NASA NTRS1990

Stability analysis of spacecraft power systems

The problems in applying standard electric utility models, analyses, and algorithms to the study of the stability of spacecraft power conditioning and distribution systems are discussed. Both single-phase and three-phase systems are considered. Of particular concern are the load and generator models that are used in terrestrial power system studies, as well as the standard assumptions of load and topological balance that lead to the use of the positive sequence network. The standard assumptions regarding relative speeds of subsystem dynamic responses that are made in the classical transient stability algorithm, which forms the backbone of utility-based studies, are examined. The applicability of these assumptions to a spacecraft power system stability study is discussed in detail. In addition to the classical indirect method, the applicability of Liapunov's direct methods to the stability determination of spacecraft power systems is discussed. It is pointed out that while the proposed method uses a solution process similar to the classical algorithm, the models used for the sources, loads, and networks are, in general, more accurate. Some preliminary results are given for a linear-graph, state-variable-based modeling approach to the study of the stability of space-based power distribution networks.

Halpin, S. M.↗
NASA NTRS1974

Parachute dynamics and stability analysis

The nonlinear differential equations of motion for a general parachute-riser-payload system are developed. The resulting math model is then applied for analyzing the descent dynamics and stability characteristics of both the drogue stabilization phase and the main descent phase of the space shuttle solid rocket booster (SRB) recovery system. The formulation of the problem is characterized by a minimum number of simplifying assumptions and full application of state-of-the-art parachute technology. The parachute suspension lines and the parachute risers can be modeled as elastic elements, and the whole system may be subjected to specified wind and gust profiles in order to assess their effects on the stability of the recovery system.

Ibrahim, S. K.↗
NASA NTRS2006

Stability Limits of a PD Controller for a Flywheel Supported on Rigid Rotor and Magnetic Bearings

Active magnetic bearings are used to provide a long-life, low-loss suspension of a high-speed flywheel rotor. This paper describes a modeling effort used to understand the stability boundaries of the PD controller used to control the active magnetic bearings on a high speed test rig. Limits of stability are described in terms of allowable stiffness and damping values which result in stable levitation of the nonrotating rig. Small signal stability limits for the system is defined as a nongrowth in vibration amplitude of a small disturbance. A simple mass-force model was analyzed. The force resulting from the magnetic bearing was linearized to include negative displacement stiffness and a current stiffness. The current stiffness was then used in a PD controller. The phase lag of the control loop was modeled by a simple time delay. The stability limits and the associated vibration frequencies were measured and compared to the theoretical values. The results show a region on stiffness versus damping plot that have the same qualitative tendencies as experimental measurements. The resulting stability model was then extended to a flywheel system. The rotor dynamics of the flywheel was modeled using a rigid rotor supported on magnetic bearings. The equations of motion were written for the center of mass and a small angle linearization of the rotations about the center of mass. The stability limits and the associated vibration frequencies were found as a function of nondimensional magnetic bearing stiffness and damping and nondimensional parameters of flywheel speed and time delay.

Kascak, Albert F.↗
NASA NTRS1974

Specialists Meeting on Rotorcraft Dynamics, Moffett Field, Calif., February 13-15, 1974, Proceedings

Analysis of specific problems in rotorcraft dynamics. Topics include hingeless rotor theory, dynamic stall modelling, periodic systems identification, analysis of complex systems with phasing matrices, flapping stability, flap-lag dynamics at high advance ratios, finite element analysis and fuselage free-vibration characteristics, coupled rotor/frame vibration methods, gust response characteristics with unsteady stall effects, antiresonance theory, cyclic feathering motions and dynamic loads, control load envelope shaping, rotor aeroelasticity, use of Floquet theory, theory of proprotors and tilt-rotors, two-bladed teetering rotors, stability of air and ground resonance, vertical-plane pendulum absorbers, multicyclic jet-flap control, engine/frame interface dynamics, and others. The minutes of the question and answer periods following the presentations are presented in the supplement. Individual items are announced in this issue.

Source record↗
NASA NTRS1995

Radio-science performance analysis software

The Radio Science Systems Group (RSSG) provides various support functions for several flight project radio-science teams. Among these support functions are uplink and sequence planning, real-time operations monitoring and support, data validation, archiving and distribution functions, and data processing and analysis. This article describes the support functions that encompass radio-science data performance analysis. The primary tool used by the RSSG to fulfill this support function is the STBLTY program set. STBLTY is used to reconstruct observable frequencies and calculate model frequencies, frequency residuals, frequency stability in terms of Allan deviation, reconstructed phase, frequency and phase power spectral density, and frequency drift rates. In the case of one-way data, using an ultrastable oscillator (USO) as a frequency reference, the program set computes the spacecraft transmitted frequency and maintains a database containing the in-flight history of the USO measurements. The program set also produces graphical displays. Some examples and discussions on operating the program set on Galileo and Ulysses data will be presented.

Morabito, D. D.↗
NASA NTRS2004

Studying Turbulence Using Numerical Simulation Databases - X Proceedings of the 2004 Summer Program

This Proceedings volume contains 32 papers that span a wide range of topics that reflect the ubiquity of turbulence. The papers have been divided into six groups: 1) Solar Simulations; 2) Magnetohydrodynamics (MHD); 3) Large Eddy Simulation (LES) and Numerical Simulations; 4) Reynolds Averaged Navier Stokes (RANS) Modeling and Simulations; 5) Stability and Acoustics; 6) Combustion and Multi-Phase Flow.

Moin, Parviz↗
NASA NTRS2015

Aerodynamic Models for the Low Density Supersonic Declerator (LDSD) Supersonic Flight Dynamics Test (SFDT)

An overview of pre-flight aerodynamic models for the Low Density Supersonic Decelerator (LDSD) Supersonic Flight Dynamics Test (SFDT) campaign is presented, with comparisons to reconstructed flight data and discussion of model updates. The SFDT campaign objective is to test Supersonic Inflatable Aerodynamic Decelerator (SIAD) and large supersonic parachute technologies at high altitude Earth conditions relevant to entry, descent, and landing (EDL) at Mars. Nominal SIAD test conditions are attained by lifting a test vehicle (TV) to 36 km altitude with a large helium balloon, then accelerating the TV to Mach 4 and and 53 km altitude with a solid rocket motor. The first flight test (SFDT-1) delivered a 6 meter diameter robotic mission class decelerator (SIAD-R) to several seconds of flight on June 28, 2014, and was successful in demonstrating the SFDT flight system concept and SIAD-R. The trajectory was off-nominal, however, lofting to over 8 km higher than predicted in flight simulations. Comparisons between reconstructed flight data and aerodynamic models show that SIAD-R aerodynamic performance was in good agreement with pre-flight predictions. Similar comparisons of powered ascent phase aerodynamics show that the pre-flight model overpredicted TV pitch stability, leading to underprediction of trajectory peak altitude. Comparisons between pre-flight aerodynamic models and reconstructed flight data are shown, and changes to aerodynamic models using improved fidelity and knowledge gained from SFDT-1 are discussed.

Van Norman, John W.↗