Search NASA⌕ Search

SEARCH · Search NASA

Results for “plastic work”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 6061-T651 Aluminum Alloy from Plate

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The matters of interest here are the elastic-plastic response and ductile failure behavior of 6061-T651 aluminum alloy under the conditions described above. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of a modular $J_2$ plasticity model with isotropic hardening as well as a ductile failure model. Both included modules that accounted for temperature and strain rate dependence. The models were coupled with an adiabatic heating module to calculate the temperature rise due to the conversion of plastic work to heat. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s as well as four geometries of notched tension specimens and two tests on specimens with shear-dominated deformations. The test data collected allowed the calibration of both the plasticity and the ductile failure models. Most test specimens were extracted from a single piece of plate to maintain consistency. Notched tension tests came from a possibly different plate, but from the same lot. When using the model in structural finite element calculations, element formulations and sizes different from those used to model the test specimens in the calibration are likely to be used. A brief investigation demonstrated that the failure model can be particularly sensitive to the element selection and provided an initial guide to compensate in a specific example.

36 MATERIALS SCIENCE↗

X-ray Diffraction Studies of Forward and Reverse Plastic Flow in Nanoscale Layers during Thermal Cycling

The biaxial stress-strain response of layers within Cu/Ni nanolaminates is determined from in-plane x-ray diffraction spectra during heating/cooling. Thinner (11 nm) Cu and Ni layers with coherent, cube-on-cube interfaces reach ~1.8 GPa (Cu) and ~2.9 GPa (Ni) without yielding. Thicker (21 nm) layers with semi-coherent interfaces exhibit unusual plastic phenomena, including extraordinary plastic work hardening rates, and forward vs. reverse plastic flow with small (~10%) changes in stress, and evidence that threshold plastic stress in Ni layers is altered by preceding plastic flow in Cu layers. Line energy, pinning strength, net interfacial dislocation density and hardness are provided.

Gram, Michael D↗

Sensitivity of pore collapse heating to the melting temperature and shear viscosity of HMX

A multiscale modeling strategy is used to quantify factors governing the temperature rise in hot spots formed by pore collapse from supported and unsupported shock waves in the high explosive HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine). Two physical aspects are examined in detail, namely the melting temperature and liquid shear viscosity. All-atom molecular dynamics simulations of phase coexistence are used to predict the pressure-dependent melting temperature up to 5 GPa. Equilibrium simulations and the Green–Kubo formalism are used to obtain the temperature- and pressure-dependent liquid shear viscosity. Starting from a simplified continuum-based grain-scale model of HMX, in this study we systematically increase the complexity of treatments for the solid–liquid phase transition and liquid shear viscosity in simulations of pore collapse. Using a realistic pressure-dependent melting temperature completely suppresses melting for supported shocks, which is otherwise predicted when treating it as a constant determined at atmospheric pressure. Alternatively, melt pools form around collapsed pores when the pressure (and melting temperature) are reduced during the release stage of unsupported shocks. Capturing the pressure dependence of the shear viscosity increases the peak temperature of melt pools by hundreds of Kelvin through viscous work. The complicated interplay of the solid-phase plastic work, solid–liquid phase transition, and liquid-phase viscous work identified here motivate taking a systematic approach to building increasingly complex grain-scale models.

36 MATERIALS SCIENCE↗

Seamless Nb tubes for SRF cavities

A. Executive Summary Understanding Developed Relationships between level of work, plastic strain orientation, level of annealing, grain size, strength, ductility, and texture were developed for heavily worked bulk RRR grade cast pure niobium (Nb). Technical Effectiveness of Approach Part A: The approach used for plastic deformation of bulk Nb was room temperature equal channel angular extrusion (ECAE). This approach is very effective for microstructural breakdown of worked and post-strain recrystallized Nb. A major problem with breaking down the microstructure of cast Nb is development of a consistent (repeatable) and uniform microstructure. This is most effectively accomplished by a series of orthogonal working steps (multipass ECAE (mECAE)) separated by full recrystallization. Forming tube from such material leads to a uniform microstructure in the tube. Part B: The approach developed to produce a microstructure in thin-walled tube that is very favorable for hydroforming into a superconducting radio frequency (SRF) cavity is tube-ECAE (tECAE). Tube-ECAE results in an axisymmetric circumferentially uniform microstructure with a texture more favorable for expansion hydroforming than tube formed by conventional methods such as extrusion, drawing, and ironing. Economic Feasibility of Methods Investigated and Demonstrated Although this was not demonstrated because of funding limitations, it is strongly believed that mECAE combined with intermediate recrystallization heat treatments and tECAE are economically viable approaches for producing a consistent, uniform, fine- or coarse-grained microstructure in RRR grade Nb tube starting from a large-grained and highly textured cast ingot. These methods are relatively easy to apply; the challenge is development of equipment and tooling that works well and is operator friendly. Commercially viable ECAE tooling for bulk Nb microstructure breakdown was developed; significant progress was made on the design of scaled-up equipment for tECAE. Patents on tECAE have been granted in Europe, Japan, and the United States. Public Benefit The approaches developed for fabricating RRR grade Nb tubing suitable for hydroforming into multi-cell SRF cavities have substantial public benefit because they will enable the manufacture of lower cost multicell SRF cavities for advanced linear particle accelerators. In addition, the approach developed for fabricating uniform and consistent axisymmetric microstructures in metal tubing can be applied to tubes made of metal alloys other than Nb. Applications exist in Ta tubing for superconductor wire applications, Mg alloy tubing for bio-implants, and aerospace tubing for structural hollow section components. The idea of tECAE can be applied to heal the heat affected zone (HAZ) in seam-welded tubing, thus erasing or healing the low-strength properties in the weld zone.

36 MATERIALS SCIENCE↗

Approximate method for predicting the permanent set in a beam in vacuo and in water subject to a shock wave

An approximate method to compute the maximum deformation and permanent set of a beam subjected to shock wave laoding in vacuo and in water was investigated. The method equates the maximum kinetic energy of the beam (and water) to the elastic plastic work done by a static uniform load applied to a beam. Results for the water case indicate that the plastic deformation is controlled by the kinetic energy of the water. The simplified approach can result in significant savings in computer time or it can expediently be used as a check of results from a more rigorous approach. The accuracy of the method is demonstrated by various examples of beams with simple support and clamped support boundary conditions.

Stiehl, A. L.↗

DROP DURABILITY ASSESSMENT OF ELECTRONIC ASSEMBLIES UNDER OFF-AXIS LOADING WITH SKEWED FIXTURES

This thesis studies drop durability of electronic assemblies when the acceleration vector is oriented at 45° to the out-of-plane direction of the circuit card. The off-axis drop tests are accomplished with a skewed fixture and are conducted as a proxy for multiaxial drop testing. Advanced shock testing and vibration test methods have been developed over the last few decades to better represent real-world field environments during ground-based laboratory testing. However, many of these test methods require expensive and specialized equipment not available in most laboratories. An alternative approach for approximating simultaneous loading along multiple axes on conventional equipment utilizes skewed fixtures which have seen use in off-axis random vibration and drop impact testing. These methods generally rely on the conversion of a uniaxial input load from the test equipment (using a uniaxial drop tower or shaker) into a multiaxial load when resolved in the reference frame of the test article (mounted on a skewed fixture). Skewed fixture design is presented and recommendations for conducting skewed angle drop testing are introduced based on local measurements along the skewed face of the fixture to accurately monitor the impact event. Characterization tests were performed with a skewed fixture, at simultaneous acceleration loads from 500 to 3,000 g in two (in-plane and out-of-plane) directions, while meeting standard time domain tolerances. Upon experimental characterization, drop shock durability tests were conducted on a printed circuit assembly (PCA). Mean drops-to-failure were measured and quantified with Weibull statistics. Dominant solder joint failure modes were identified via failure analysis. Prior work on inclined angle impact testing is limited, and the majority of solder joint interconnect level fatigue studies are conducted considering perpendicular loading normal the circuit card. Low-cycle fatigue curves are generated based on plastic strain and plastic work density within the solder joint. A multiscale nonlinear finite element model is used to relate board-level flexure to solder joint interconnect level plastic strain. A high strain rate solder constitutive model allows for accurate modeling of solder plasticity resulting from high-impact drop shock. Fatigue parameters are computed from the Coffin-Manson relation and Palmgren-Miner damage accumulation. This work serves to apply established low-cycle fatigue methods for conventional drop shock loading (impact normal to circuit card) to non-perpendicular loading with a skewed fixture.

Hower, Jonathan [Kansas City National Security Cam↗

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.

36 MATERIALS SCIENCE↗

Modeling of Failure Modes Induced by Plastic Strain Localization in Dual Phase Steels

Microstructure level inhomogeneity between the harder martensite phase and the softer ferrite phase renders the dual phase (DP) steels more complicated failure mechanisms and associated failure modes compared to the conventionally used low alloy homogenous steels. This paper examines the failure mode DP780 steel and DP 980 steel under different loading conditions using finite element analyses on the microstructure levels. Micro-mechanics analyses based on the actual microstructures of DP steel are performed. The two-dimensional microstructure of DP steel was recorded by scanning electron microscopy (SEM). Mechanical properties of the ferrite and martensite phases exhibit the dependency of the different chemistry and thermal mechanical processes. The plastic work hardening properties of the ferrite phase was determined by the synchrotron-based high-energy X-ray diffraction technique. The work hardening properties of the martensite phase were calibrated and determined based on the uniaxial tensile test results. Under different loading conditions, different failure modes are predicted in the form of plastic strain localization. The local failure mode was closely related to the stress state in the material. Under plane stress condition with free lateral boundary, one dominant shear band develops and leads to final failure of the material. However, if the lateral boundary was strictly constrained, splitting failure perpendicular to the loading direction is predicted. On the other hand, under plane strain loading condition, commonly observed necking phenomenon is predicted which leads to the final failure of the material. Numerical predictions were well validated by the experimental.

36 MATERIALS SCIENCE↗

Attaining regularization length insensitivity in phase-field models of ductile failure

In this work, a cohesive phase-field model of ductile fracture in a finite-deformation setting is presented. The model is based on a free-energy function in which both elastic and plastic work contributions are coupled to damage. Using a strictly variational framework, the field evolution equations, damage kinetics, and flow rule are jointly derived from a scalar least-action principle. Particular emphasis is placed on the use of a rational function for the stress degradation that maintains a fixed effective strength with decreasing regularization length. The model is employed to examine crack growth in pure mode-I problems through the generation of crack growth resistance (J-R) curves. In contrast to alternative models, the current formulation gives rise to J-R curves that are insensitive to the regularization length. Numerical evidence suggests convergence of local fields with respect to diminishing regularization length as well.

42 ENGINEERING↗

Predicting Failure Modes and Ductility of Dual Phase Steels Using Plastic Strain Localization

Ductile failure of metals is often treated as the result of void nucleation, growth and coalescence. Various criteria have been proposed to capture this failure mechanism for various materials. In this study, ductile failure of dual phase steels is predicted in the form of plastic strain localization resulting from the incompatible deformation between the harder marternsite phase and the softer ferrite matrix. Microstructure-level inhomogeneity serves as the initial imperfection triggering the instability in the form of plastic strain localization during the deformation process. Failure modes and ultimate ductility of two dual phase steels are analyzed using finite element analyses based on the actual steel microstructures. The plastic work hardening properties for the constituent phases are determined by the in-situ synchrotron-based high-energy X-ray diffraction technique. Under different loading conditions, different failure modes and ultimate ductility are predicted in the form of plastic strain localization. It is found that the local failure mode and ultimate ductility of dual phase steels are closely related to the stress state in the material. Under plane stress condition with free lateral boundary, one dominant shear band develops and leads to final failure of the material. However, if the lateral boundary is constrained, splitting failure perpendicular to the loading direction is predicted with much reduced ductility. On the other hand, under plane strain loading condition, commonly observed necking phenomenon is predicted which leads to the final failure of the material. These predictions are in reasonably good agreement with experimental observations.

36 MATERIALS SCIENCE↗

Reliability of Sn-3.5Ag Solder Joints in High Temperature Packaging Applications

There is a significant need for next generation, high performance power electronic packages and systems with wide band gap devices to operate at high temperatures in automotive and electricity transmission applications. Sn-3.5Ag solder is a candidate for use in such packages with potential operating temperatures up to 200oC. However, there is a need to understand thermal cycling reliability of Sn-3.5Ag solders subject to such operating conditions. The results of a study on the damage evolution occurring in large area Sn-3.5Ag solders joints between silicon dies and DBC substrates subject to thermal cycling between 200oC and 5oC is presented in this paper. Damage accumulation was followed using high resolution X-ray radiography techniques while nonlinear finite element models were developed based on the mechanical property data available in literature to understand the relationship between the stress state within the solder joint and the damage evolution occurring under thermal cycling conditions. It was observed that regions of damage observed in the experiments do not correspond to the finite element predictions of the location of regions of maximum plastic work.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

FY18 Thermal Mechanical Failure: SS-304L calibration Taylor-Quinney parameter measurement and kinematic hardening plasticity

The Thermal-Mechanical Failure project conducted in FY 2018 was divided into three sub projects: 1. Calibration of the uniaxial response of 304L stainless steel specimens at three temperatures (20, 150 and 310°C) and two strain rates (2 x 10 -4 and 8 x 10 -2 s -1 ); 2. Measurements of the fraction of plastic work that is converted to heat (Taylor-Quinney parameter) for 304L stainless steel. This fraction is usually assumed to be 0.95 in analysis because data is only available for a few materials; 3. Comparison of the predicted responses by isotropic and kinematic hardening plasticity models in a couple of simplified structural problems. One problem is a can crush followed by pressurization and is loosely associated with a crush-and-burn scenario. The other problem consists of a drop scenario of a thin-walled cylinder that carries a cantilevered internal mass.

36 MATERIALS SCIENCE↗

Numerical solution of shock and ramp compression for general material properties

A general formulation was developed to represent material models for applications in dynamic loading. Numerical methods were devised to calculate response to shock and ramp compression, and ramp decompression, generalizing previous solutions for scalar equations of state. The numerical methods were found to be flexible and robust, and matched analytic results to a high accuracy. The basic ramp and shock solution methods were coupled to solve for composite deformation paths, such as shock-induced impacts, and shock interactions with a planar interface between different materials. These calculations capture much of the physics of typical material dynamics experiments, without requiring spatially-resolving simulations. Example calculations were made of loading histories in metals, illustrating the effects of plastic work on the temperatures induced in quasi-isentropic and shock-release experiments, and the effect of a phase transition.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multiphase representation of hotspot formation and growth

Multiphase reacting flow approach has been adopted for modeling of hotspot formation and growth on sub-zonal scale. Mechanical response of the high explosive (HE) is modeled by the Visco-Plastic SCRAM model which includes plastic work, crack growth, and frictional heating along the cracks. In this work a sub-zonal regions with high temperature, hotspots, are modeled as a new phase. Formation and growth of the hotspot phase from the cold phase is modeled as a phase change. Each phase has its own temperature and pressure. Chemical reactions also progress in both phases. The growth of hotspots are determined by the solution of the heat conduction equation with appropriate heat sources due to friction and plastic heating. Sample calculations using the BABBO code show successful detonation calculations with hotspot formation and growth.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Equation of state and strength of diamond in high-pressure ramp loading

Diamond is used extensively as a component in high-energy-density experiments, but existing equation of state (EOS) models do not capture its observed response to dynamic loading. In particular, in contrast with first-principles theoretical models of equilibrium multiphase EOS, no solid-solid phase changes have been detected, and no general-purpose EOS models match the measured ambient isotherm. We have performed density functional theory (DFT) calculations of the diamond phase to ~10 TPa, well beyond its predicted range of thermodynamic stability, and used these results as the basis of a Mie-Grüneisen EOS. We also performed DFT calculations of the elastic moduli, and calibrated an algebraic elasticity model for use in simulations. We then estimated the flow stress of diamond by comparison with the stress-density relation measured experimentally in ramp-loading experiments. Furthermore, the resulting constitutive model allows us to place a constraint on the Taylor-Quinney factor (the fraction of plastic work converted to heat) from the observation that diamond does not melt on ramp compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

FEM Analysis of Defects and Microstructure Evolution during Hot Working of Specialty Alloys

The main goals of process simulation in manufacturing are to reduce manufacturing/part development time and cost as well as increasing quality and productivity. In this study, porosity evolution is modeled by introducing a porosity evolution parameter, which is function of strain rate and stress triaxiality factor. Applicability is shown by simulating the first two stages of an ingot conversion process; variables are die geometry and bite size. Moreover, application is extended to hot shape rolling, where the geometry of the oval passes is the variable. Validation is carried out through evaluation of samples from final products. Also, surface defects in hot shape rolling are tracked by studying the instability during the rolling of the material. Plastic work approach was used to judge the occurrence of instability during the process. The effect of number of passes and roll gap was examined to predict the occurrence of surface cracking. On the other hand, unrecrystallized grains and coarse grain problem are other significant problems in the metalworking industry. A recrystallization model is implemented in a finite element framework, to study the effect of forging parameters on the microstructure evolution during ingot conversion process of a superalloy.

36 MATERIALS SCIENCE↗

Coupled thermal stress simulations of ductile tearing

Predictions for ductile tearing of a geometrically complex Ti-6Al-4V plate were generated using a Unified Creep Plasticity Damage model in fully coupled thermal stress simulations. Uniaxial tension and butterfly shear tests performed at displacement rates of 0.0254 and 25.4 mm/s were also simulated. Results from these simulations revealed that the material temperature increase due to plastic work can have a dramatic effect on material ductility predictions in materials that exhibit little strain hardening. Furthermore, this occurs because the temperature increase causes the apparent hardening of the material to decrease which leads to the initiation of deformation localization and subsequent ductile tearing earlier in the loading process.

36 MATERIALS SCIENCE↗