Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymer precursors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Solid Electrolytes for Li–S Batteries: Solid Solutions of Poly(ethylene oxide) with Li x PON- and Li x SiPON-Based Polymers

We report here efforts to synthesize free-standing, dry polymer electrolytes that exhibit superior ionic conductivities at ambient for Li–S batteries. Co-dissolution of poly(ethylene oxide) (PEO) (M n 900k) with Li x PON and Li x SiPON polymer systems at a ratio of approximately 3:2 followed by casting provides transparent, solid-solution films 25–50 μm thick, lowering PEO crystallinity, and providing measured impedance values of 0.1–2.8 × 10 –3 S/cm at ambient. These values are much higher than simple PEO/Li + salt systems. These solid-solution polymer electrolytes (PEs) are (1) thermally stable to 100 °C; (2) offer activation energies of 0.2–0.5 eV; (3) suppress dendrite formation; and (4) enable the use of lithium anodes at current densities as high as 3.5 mAh/cm 2 . Here, galvanostatic cycling of SPAN/PEs/Li cell (SPAN = sulfurized, carbonized polyacrylonitrile) shows discharge capacities of 1000 mAh/g sulfur at 0.25C and 800 mAh/g sulfur at 1C with high coulumbic efficiency over 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2021

Alkaline anion exchange membranes derived from diphenylethylene and co-monomer feedstock

The anion exchange membranes exhibit enhanced chemical stability and ion conductivity when compared with traditional styrene-based alkaline anion exchange membranes. A copolymer backbone is polymerized from a reaction medium that includes a diphenylalkylene and an alkadiene. The copolymer includes a plurality of pendant phenyl groups. The diphenyl groups on the polymer backbone are functionalized with one or more haloalkylated precursor substrates. The terminal halide from the precursor substrate can then be substituted with a desired ionic group. The diphenylethylene-based alkaline anion exchange membranes lack the .alpha.-hydrogens sharing tertiary carbons with phenyl groups from polystyrene or styrene-based precursor polymers, resulting in higher chemical stability. The ionic groups are also apart from each other by about 3 to 6 carbons in the polymer backbone, enhancing ion conductivity. These membrane are advantageous for use in fuel cells, electrolyzers employing hydrogen, ion separations, etc.

Lee, Sangwoo↗
DOE OSTI2024

Alkaline anion exchange membranes derived from diphenylethylene and co-monomer feedstock

The anion exchange membranes exhibit enhanced chemical stability and ion conductivity when compared with traditional styrene-based alkaline anion exchange membranes. A copolymer backbone is polymerized from a reaction medium that includes a diphenylalkylene and an alkadiene. The copolymer includes a plurality of pendant phenyl groups. The diphenyl groups on the polymer backbone are functionalized with one or more haloalkylated precursor substrates. The terminal halide from the precursor substrate can then be substituted with a desired ionic group. The diphenylethylene-based alkaline anion exchange membranes lack the α-hydrogens sharing tertiary carbons with phenyl groups from polystyrene or styrene-based precursor polymers, resulting in higher chemical stability. The ionic groups are also apart from each other by about 3 to 6 carbons in the polymer backbone, enhancing ion conductivity. These membrane are advantageous for use in fuel cells, electrolyzers employing hydrogen, ion separations, etc.

Lee, Sangwoo↗
DOE OSTI2025

Investigating Fast Scanning Calorimetry and Differential Scanning Calorimetry as Screening Tools for Thermoset Polymer Material Compatibility with Laser-Based Powder Bed Fusion

As additive manufacturing (AM) technology has developed and progressed, a constant topic of research in the area is expanding the library of materials to be used with these techniques. Among AM methods that utilize polymers, laser-based powder bed fusion (PBF-LB) has preferentially used thermoplastic polymers as its starting materials, but the deposition and material joining method employed in PBF-LB may also be compatible with powdered thermoset polymer precursors as feedstocks. To assess the compatibility of candidate thermosetting polymers and PBF-LB, characterization techniques and protocols that link fundamental material behavior to material behavior in the processing environment are needed. Therefore, the objectives of this work are to compare the curing behavior measured with two different calorimetry techniques that can operate in different heating rate regimes, differential scanning calorimetry (DSC) and fast scanning calorimetry (FSC), and to assess the capabilities of these techniques to act as materials screening tools for PBF-LB. A commercial polyester powder coating is used as a model material to evaluate the potential of obtaining complimentary information for material screening through a combination of calorimetry methods, and its non-isothermal curing behavior is measured at heating rates between 5 °C/min and 7500 °C/min. Curing exotherms are observed with both calorimetry techniques, and comparing the enthalpy associated with curing shows that incomplete curing occurs at higher heating rates, with relative conversion values of approximately 30%. The curing data are fit with two isoconversional models, Friedman and Starink, which show a reduced activation energy at higher heating rates as well, signifying a lower barrier to curing at the conditions used in the FSC experiments. Overall, the results of this work indicate that using these two calorimetry techniques as tiered screening tools can provide valuable information about how curing may proceed in PBF-LB and inform materials selection and design activities for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A universal and facile approach for building multifunctional conjugated polymers for human-integrated electronics

Polymer semiconductors have shown distinct promise for the development of human- integrated electronics, owing to their solution processability and mechanical softness. However, numerous functional properties required for this application domain face synthetic challenges to be imparted onto conjugated polymers and thus combined with efficient charge- transport property. Here, we develop a “click-to-polymer” (CLIP) synthesis strategy for conjugated polymers, which uses a click reaction for the facile and versatile attachment of diverse types of functional units to a pre-synthesized conjugated-polymer precursor. With four types of functional groups, we show that functionalized polymers from this CLIP method can still retain good charge-carrier mobility. Here, we take two realized polymers to showcase the photo-patternable property and biochemical sensing function, both of which advance the state of the art of realizing these two types of functions on conjugated polymers. We expect the expanded use of this synthesis approach can largely enrich the functional properties from conjugated polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Developing a New Polyolefin Precursor for Low-Cost, High-Strength Carbon Fiber

Current high-strength carbon fibers (CFs) are mostly derived from PAN polymer precursor, which are very expensive with limited usage in the high-end products. On the other hand, it has also stimulated research interest to develop new low-cost precursors and manufacturing process. Despite numerous studies, researchers have yet to develop a new polymeric precursor that is less expensive, melt-spinnable, and offers a high C-yield. In this three-year R&D project, we proposed three consecutive research phases, including (i) the development of new polyolefin-based precursors that can be thermally transformed to C material in one heating step under inert atmosphere and achieved a C-yield >80%, which is more than 60% higher than that of current PAN precursor, (ii) With the suitable new polyolefin-based precursor, we can focus on CF manufacturing process, including fiber spinning, stabilization, and carbonization, to form high quality carbon fibers with the desirable polymorphous morphology, and (iii) the investigation of thermal conversion process under tension for converting polyolefin-based precursor fibers to high tensile strength carbon fibers with specific graphite crystallite size, orientation of basal line, order-disorder ratio, fiber diameter, and reduced structural defect (voids). composites.

08 HYDROGEN↗
DOE OSTI2023

Direct synthesis of ordered mesoporous materials from thermoplastic elastomers

Abstract The ability to manufacture ordered mesoporous materials using low-cost precursors and scalable processes is essential for unlocking their enormous potential to enable advancement in nanotechnology. While templating-based methods play a central role in the development of mesoporous materials, several limitations exist in conventional system design, including cost, volatile solvent consumption, and attainable pore sizes from commercial templating agents. This work pioneers a new manufacturing platform for producing ordered mesoporous materials through direct pyrolysis of crosslinked thermoplastic elastomer-based block copolymers. Specifically, olefinic majority phases are selectively crosslinked through sulfonation reactions and subsequently converted to carbon, while the minority block can be decomposed to form ordered mesopores. We demonstrate that this process can be extended to different polymer precursors for synthesizing mesoporous polymer, carbon, and silica. Furthermore, the obtained carbons possess large mesopores, sulfur-doped carbon framework, with tailorable pore textures upon varying the precursor identities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tailoring the Interfacial Interactions of Porous Polymer Membranes to Accelerate Atomic Layer Deposition: The Latent Path to Antifouling Membranes

Atomic layer deposition (ALD) is a powerful strategy to engineer hybrid organic-inorganic membranes with emergent functionalities. The combination of atomic-level thickness control, a wide materials palette, and unprecedented conformality allows the physiochemical properties (e.g., hydrophilicity) of mesoporous polymer membranes to be precisely tuned. The nucleation of ALD material growth on polymer surfaces relies on Lewis acid-base interactions and remains an overlooked motif with tremendous potential to accelerate ALD nucleation and growth. Strategies to enhance these interactions could enable desirable properties such as antifouling behavior to be imparted on inert polymer surfaces that lack the necessary functional groups for ALD nucleation. Here, in this study, we demonstrate that the reactivity of polyacrylonitrile (PAN) membranes toward ALD metal oxide (MO) precursors with Lewis acid characteristics is enhanced by introducing strong Lewis base functional groups (amidoxime: Am) on the PAN backbone (Am-PAN). The resulting Lewis acid-base interactions accelerate the MO nucleation in Am-PAN and reduce the number of deposition cycles required to achieve hydrophilicity compared with the untreated PAN membrane. Unveiling the reaction mechanism, in situ Fourier transform infrared (FTIR) spectroscopy measurements established enhanced interaction dynamics between the ALD MO precursors and the Am-PAN membrane, unlike the PAN membrane. Spectroscopic ellipsometry and thermogravimetric analysis measurements revealed higher MO loadings in Am-PAN membranes compared to PAN membranes for the same number of ALD cycles. We found that strong Lewis acid-base interactions accelerated the ALD for a range of materials including Al 2 O 3 , TiO 2 , SnO 2 , and ZnO. More broadly, our work demonstrates that tailoring metal-precursor-polymer interactions is a powerful strategy to accelerate and modulate the ALD. We used this design strategy to fabricate Al 2 O 3 -Am-PAN hybrid membranes that showed 2-fold higher antifouling capability compared to pristine PAN membranes prepared with an equivalent number of Al 2 O 3 ALD cycles. Our approach expands the scope of design options for fouling-resistant porous hybrid inorganic-organic membranes and may ultimately reduce the operational costs of water treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Actinic and electron beam radiation curable water based electrode binders and electrodes incorporating same

A process for manufacturing an electrode utilizing electron beam (EB) or actinic radiation to cure the electrode binder is provided. A process is also disclosed for mixing specific actinic or EB radiation curable polymer precursors with electrode solid particles to form an aqueous mixture, application of the mixture to an electrode current collector, followed by the application of actinic or EB radiation to the current collector for curing the polymer, thereby binding the electrode binder to the current collector. Lithium ion batteries, electric double layer capacitors, and components produced therefrom are also provided.

Voelker, Gary E.↗
DOE OSTI2022

Influence of Thermal Treatment on Preceramic Polymer Grafted Nanoparticle Network Formation: Implications for Thermal Protection Systems and Aerospace Propulsion Components

Preceramic polymer grafted nanoparticles (PCP GNPs) offer potential advantages in the production of polymer-derived ceramic composites compared to neat preceramic polymers (PCPs), such as reduced thermal shrinkage and increased char yield. In comparison to traditional composites (particles + free polymer), PCPs avoid issues of compatibility, agglomeration, and phase separation during processing and provide routes to control nanoparticle arrangement. Prior literature has established that the conversion efficiency of PCPs and PCP GNPs to ceramics and ceramic composites is linked to the thermal pretreatment of these precursor polymers (e.g., curing). In this paper, we investigate the material transformations that occur when exposing PCP GNPs to a low-temperature thermal treatment (≤250 °C) prior to pyrolysis. The PCP GNPs explored in this study possessed silica nanoparticle cores but were distinct in their PCP coronas, having poly(1,1-dimethylpropylsilane) (allyl-GNP)- or poly(1,1-dimethylbenzylethylsilane) (styryl-GNP)-grafted polymers. After undergoing low-temperature thermal treatment, these PCP GNPs exhibited increased char yield at 800 °C; however, unlike commercial PCPs (e.g., allylhydridopolycarbosilane (SMP-10)), obvious cross-linkable sites are not present in the PCP corona structure. Differential scanning calorimetry, oscillatory rheology, and X-ray photon correlation spectroscopy were utilized to elucidate the thermally induced material changes in the allyl- and styryl-GNPs. Thermally induced changes to the structure and behavior of the PCP GNPs were determined to be linked to the chemical structure of the grafted polycarbosilane chains. Styryl-GNPs experienced a curing event between 180 and 250 °C, effecting the formation of a network, which contributed to char yield improvement (at 800 °C). The nanoscale dynamics of this material also shows a transition from diffuse behavior to ballistic behavior because of the cross-linking event. Conversely, the allyl-GNPs did not exhibit a curing event under heat treatment but did show an increase in thermally induced physical cross-linking. The allyl-GNP physical network is stronger after the first cycle of thermal treatment, and it is considered that this contributed to the improvement in char yield post thermal treatment. The advancements in the understanding of the cross-linking behavior of these hybrid materials are expected to advance the application of these materials to turbine engine, advanced friction, and heat-shielding components.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Formation of Non-Doped Cubic Lithium Lanthanum Zirconium Oxide Nanofibers: Insights from In Situ Synchrotron X-Ray Scattering

This study investigates the formation mechanism of non-doped cubic lithium lanthanum zirconium oxide (c-LLZO) nanofibers using in situ synchrotron X-ray scattering techniques. Electrospun polymer precursor nanofibers were annealed at temperatures up to 800 °C, enabling real-time tracking of phase transitions via simultaneous small-angle X-ray scattering (SAXS), wide-angle X-ray scattering (WAXS), and evolved CO 2 gas analysis. The results reveal a three-step transformation pathway: polymer decomposition, formation of La 2 Zr 2 O 7 (LZO), and direct conversion of LZO to c-LLZO without intermediate tetragonal phases detected within the sensitivity of our in situ WAXS measurement. Cryo-electron energy loss spectroscopy (EELS) further elucidates the role of lithium diffusion, showing Li enrichment at fiber surfaces and Li deficiency in the interior, which stabilizes the cubic phase. This Li segregation effect in nanostructured LLZO materials extends beyond the previously reported size effect. This work advances the understanding of c-LLZO formation mechanisms and provides practical insights for optimizing synthesis routes to achieve phase-pure c-LLZO for solid-state battery applications.

LLZO phase stability↗
DOE OSTI2020

Method to produce colorless, high porosity, transparent polymer aerogels

A method to produce a polymer gel includes dissolving precursors in a solvent to form a precursor solution, the precursors including polymer precursors, a stable free radical, one or more initiating radicals, and one or more stable free radical control agents, and heating the precursor solution to a temperature of polymerization to produce a cross-linked gel. A dried polymer aerogel has a Brunauer-Emmett Teller (BET) surface area over 100 m2/g, porosity of greater than 10%, visible transparency greater than 20%, color rendering index of over 20%, and average pore size of less than 100 nm.

Chintapalli, Mahati↗
DOE OSTI2022

Understanding curing dynamics of arylacetylene and phthalonitrile thermoset blends

Tetrakis(phenylethynyl)benzene (TPEB), a high char yield arylacetylene resin, was blended with a resorcinol-based PEEK™-like oligomeric phthalonitrile resin (Res). Here, we observed the influence of each polymer precursor on the structural changes and material dynamics of different mixtures of these resins during thermal curing to produce thermosets with high char retention. We provide insight to help understand fundamental processes that control and tune this complex thermally driven curing mechanism, which, to date, has not been well understood. We show that an equivalent blend of Res and TPEB mitigates the exothermic curing process and exhibits a low viscosity, which may facilitate processing of these thermosetting blends for composite manufacturing. To obtain a more comprehensive overview of the different dynamics of these polymers during curing, we correlated thermodynamic changes with rheology, materials characterization, and molecular dynamics derived from neutron scattering. Our efforts shed more light on the thermally driven chemical changes, physical transformation, and gelation dynamics that drive or accompany softening and curing of these two distinct crosslinking resin groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Highly Ordered Carbon Coating Prepared with Polyvinylidene Chloride Precursor for High‐Performance Silicon Anodes in Lithium‐Ion Batteries

Abstract A highly ordered carbon structure based on polyvinylidene chloride precursor has been developed to host silicon nanoparticles. The stoichiometric ratio of sacrificial H and Cl elements facilitated full utilization of the carbon content of the precursor that produced robust carbon coatings on silicon nanoparticles with excellent mechanic properties and electrochemical stabilities. The optimal sintering temperature and carbon content have been investigated. When evaluated as the anode of a lithium‐ion battery (LIB), the Si : C 1 : 2 composite sintered at 800 °C (SiC12‐800) provided excellent capacity retention of 85 % at 0.1 C after 50 cycles with an enhanced CE, which reached 99 % only after 10 cycles. The SiC12‐800 electrode maintained a specific capacity of 709.2 mAh/g after 300 cycles at 0.3 C, and delivered a high rate performance of 737.9 mAh/g and 485.6 mAh/g at 5 C and 10 C, respectively. The results indicate that polymer precursors with stoichiometric ratio of sacrificial elements have high potential for generating highly robust carbon coatings for silicon anodes in high energy density LIBs.

Zhou, Shuo↗
DOE OSTI2023

Advanced Algal Biofoundries for the Production of Polyurethane Precursors

The primary goal of the BEEPs project was to develop a process that could accelerate the development of algae as bioproduction platforms, from initial chemical product concept to an economically viable market supply. Under this program we elected to develop strains of algae that could generate polyurethane precursors, while simultaneously developing basic genetic tools to enable improved algal production systems. This program was specifically designed to incorporate National Laboratories as a means to utilize the expertise and facilities for new bio-production platforms. To that end, we designed a program to collaborate with the Agile BioFoundry at Lawrence Berkeley National Laboratory (LBNL) and computational platforms at Pacific Northwest National Laboratory (PNNL). In addition to these National Laboratory partners, we also had academic partners from UC Davis and Georgia Tech, as well as commercial partners Algenesis Materials and BASF. To achieve these goals, we initially focused on developing the genetic tools and high throughput screening technologies necessary to generate and assess production of polymer precursors (succinic acid) in algae and cyanobacteria, including advanced promoters and biosensors. In parallel, we computationally identified potential production bottlenecks and then used the developed genetic tools to increase production rates and yields. Constant feedback of data was used in conjunction with machine learning, high-throughput cell sorting, and synthetic biology, for additional targeted metabolic engineering. Multiple rounds of tool design, building, testing, and learning were supplied to partners at PNNL and LBNL to develop new models and tools that could expedite bioproduction platform development and increase yield performance. We targeted, and achieved, the FOA requirement yield metric of 20 g/L, as a milestone and deliverable from at least one of our engineered strains for the production of succinic acid.

09 BIOMASS FUELS↗
DOE OSTI2022

Tailored Mesoporous Microspheres by Polymerization-Induced Microphase Separation in Suspension

We describe the preparation of block polymer beads by aqueous suspension polymerization to create poly(caprolactone) (PCL)-block-poly(styrene-co-divinylbenzene) beads that can be selectively etched under basic conditions to yield mesoporous polymer microspheres with uniform pore size. Polyvinylalcohol was used to stabilize the suspension polymerization in which styrene and divinylbenzene monomers were polymerized from a PCL macrochain transfer agent (macroCTA). The resulting polymerization-induced microphase separation process led to a nanostructured bicontinuous morphology. The particle size and pore size were independently tunable: the particle size was controlled by the stir rate of the suspension polymerization-yielding average diameters ranging from 60 to 300 μm-while the pore size was determined by the molar mass of the PCL block, with the mode pore diameters being 6 nm and 11 nm after etching beads made using 13 and 45 kg/mol PCL blocks, respectively. Based on nitrogen sorption measurements, the surface areas of the beads were ~300 m 2 /g when using a PCL macroCTA of 13 kg/mol. The beads were homogenous throughout on the micron length scale as determined by confocal Raman microscopy and lacked an impermeable skin layer as confirmed by scanning electron microscopy. Furthermore, the scalability of suspension polymerization allows for the simple synthesis of large quantities of thermoset microspheres with uniform pore size. We also demonstrate the ability to incorporate functional pore walls into the beads using multiblock precursor polymers. These functionalized mesoporous polymer beads show high affinity for ionic dyes in aqueous solutions (as a proof of principle) and remove dye from the solution at rates exceeding those of commercial ion-exchange resins. The developed procedure could be used to generate other functional surface chemistries with important applications in heterogeneous catalysis, chromatography, and water remediation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Sustainable Direct Recycling of Lithium-Ion Batteries via Solvent Recovery of Electrode Materials

Separation of electrode materials from their current collectors is an enabling step toward recovering critical materials from spent lithium-ion batteries. In this study, a highly efficient, cost-effective, and environmentally sustainable separation process was developed for that purpose. Ethylene glycol, a vital commodity chemical as an antifreeze and polymer precursor, is used to delaminate electrode materials at low temperatures in seconds without altering the crystalline structure and morphology of active electrode materials. The recovered current collectors were intact without any corrosion. The authors also found that the solvent could be continuously reused, leading to the development of a closed-loop ecosystem and lithium-ion battery circular economy. The ultrafast delamination was driven by the competitive inhibition of binding through the weakening of hydrogen bonding. The ethylene glycol-based separation is a sustainable electrode recovery process that paves the way for battery recycling.

25 ENERGY STORAGE↗
DOE OSTI2026

Polymer coatings on zirconia microspheres via rotating flow fluid dynamics

Conventional tristructural isotropic (TRISO) coatings for nuclear fuels require multi-step and expensive formation processes; any breakage of the coatings may lead to fission species release. Polymer derived ceramic (PDC) coatings can be a suitable alternative to address these issues. In this study, allylhydridopolycarbosilane (SMP-10) coatings were created on yttria stabilized zirconia (YSZ) microspheres using a Rotating Flow Fluid Dynamics (RFFD) coating method. The effects of curing temperature, rotation speed, and coating cycle/time on the coating were analyzed. Surface functionalization of YSZ microspheres with NaOH resulted in good adhesion between the polymer precursor and the YSZ kernel particles. Spectroscopy analysis revealed complete curing of SMP-10 coated YSZ at 160 °C. Rotation speed and coating time significantly affect the coating characteristics. After 3 cycles at lower rotation speed (50 rpm) for 10 min each, the coating obtained was uniform and homogeneous. In comparison, the coating showed almost 10 times less eccentricity at a high rotation speed of 300 rpm. Compared with the coatings prepared at 300 rpm condition, the coatings have higher sphericity and lower eccentricity at 50 rpm. Overall, this study provides a novel and effective route for fabricating and curing SMP-10 precursor coatings on YSZ microspheres.

Ravi, Nivetha [University of Alabama, Birmingham]↗