Effect of polar side chains on neutral and p-doped polythiophene
Abstract not provided
Finn, Peter A.↗
SEARCH · Search NASA
Results for “polythiophene”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Polythiophene side chain chemistry and its impact on advanced composite anodes for lithium-ion batteries
Tailored side chains can improve structural stability, ion transport and capacity retention, offering a solution to key challenges such as capacity fade and electrode degradation in lithium-ion batteries.
Li, Han [Department of Chemical and Bimolecular En↗
Tuning the Intermolecular Electrostatic Interaction toward High-Efficiency and Low-Cost Organic Solar Cells
Organic solar cells (OSCs) have achieved much progress with rapidly increasing power conversion efficiencies (PCEs). It should be noted that the top-performance OSCs are generally consisted of active materials with complex chemical structures, resulting in high costs. Here, combining the material design and morphology control, high-efficiency OSCs are fabricated by a low-cost donor: acceptor blend. A completely non-fused electron acceptor named Tz is designed and synthesized via introducing thiazole units on both sides of a bithiophene core, which shows an outstanding PCE of 13.3% with a typical polythiophene donor. More importantly, optimization guidelines are presented to get excellent morphology for low-cost donor:acceptor systems. Three polythiophenes are selected, poly(3-hexylthiophene) and its two derivatives with electron-withdrawing substitutions (PDCBT and PDCBT-2F), as donors to fabricate the cell devices. The computational and experimental data reveal that decreasing the electrostatic interaction between polythiophene and Tz is the key to getting a suppressed miscibility and thus a high phase purity. Finally, this study provides insight into the molecular design and donor:acceptor matching requirements for high-efficiency and low-cost OSCs.
14 SOLAR ENERGY↗
Unraveling the Photovoltaic, Mechanical, and Microstructural Properties and Their Correlations in Simple Poly(3‐pentylthiophene) Solar Cells
Abstract The power conversion efficiency of polythiophene organic solar cells is constantly refreshed. Despite the renewed device efficiency, very few efforts have been devoted to understanding how the type of electron acceptor alters the photovoltaic and mechanical properties of these low‐cost solar cells. Herein, the authors conduct a thorough investigation of photovoltaic and mechanical characteristics of a simple yet less‐explored polythiophene, namely poly(3‐pentylthiophene) (P3PT), in three different types of organic solar cells, where ZY‐4Cl, PC 71 BM, and N2200 are employed as three representative acceptors, respectively. Compared with the reference poly(3‐hexylthiophene) (P3HT)‐based solar cells, P3PT‐based devices, all perform more efficiently. Particularly, the P3PT:ZY‐4Cl blend exhibits the highest efficiency (ca. 10%) among the six combinations and outperforms the prior top‐performance system P3HT:ZY‐4Cl. Furthermore, the blend films based on N2200 exhibit a high crack‐onset strain of ∼38% on average, which is approximately 15‐ and 17‐times higher than those of ZY‐4Cl and PC 71 BM, respectively. The microstructural origins for the above difference are well elucidated by detailed grazing incidence X‐ray scattering and microscopy analysis. This work not only underlines the potential of P3PT in prolific solar cell research but also demonstrates the superior tensile properties of polythiophene‐based all‐polymer blends for the preparation of stretchable solar cells.
Polymer Science↗
Low-gravity electrodeposition and growth of polymer thin films with large third-order optical nonlinearities by electrochemical processes for devices: Thiophene-based polymers
It has been proposed that NLO thin film properties may be improved by low-gravity processing. Strong candidates for NLO thin film applications are the polythiophenes. Polymeric thiophenes are attractive materials due to their ease of preparation, stability, and high X(exp 3). A simple and convenient method for preparation of polythiophenes is electrochemical oxidation. We will apply some of our experience and lessons learned in low-gravity metal, metal/cermet electrode position to improve the quality of polythiophene(s) thin films. In low gravity electrode position of Ni at a high rate on an Au substrate often results in the production of an x-ray non diffracting surface. Cobalt metal deposition does not give this result nor does Ni when deposited similarly on a glassy carbon substrate. Co/Ni alloy composition produced during electrode position is strongly dependent upon the amount of convection. Code position of neutral inert cermets with metals is influenced significantly by the presence of gravity and the size of the cermets. Tracks left in the 1-g surfaces by unsuccessful particle occlusion indicate suspension of the large particles is not the only reason for poor volume percentages of the larger particles in the deposits. All size particles are more homogeneously distributed in the deposits in low-gravity electrocodeposition than in 1-g. Low gravity gives larger volume percentages for the larger particles in the deposits, while 1-g gives larger volume percentages for the smaller particles. Intermediate size particles give mixed results. The experimental cells were constructed with flat electrode end plates such that 1-g bench reference electrode positions could be carried out at various orientations with respect to gravity. A series of bench studies using similar designed cells are suggested so that convection modification can be applied to electrochemical thin film preparation. Convection effects can then be coupled with other parameter variations in current, temperature, concentration, solvent, electrolyte, and anode substrates to optimize the properties of NLO thin films before resorting to low-gravity processing.
Penn, Benjamin G.↗
Substituted thiophene oligomers and polymers
The present disclosure provides an antimicrobial substrate including a substrate and a polythiophene polymer. The polythiophene polymer has a number of repeated monomer units from n is 5-14 or 30 to 120, a number average molecular weight (Mn) from 1,000 to 4,000 or 10,000 to 40,000; and a polydispersity index (PDI) from 1 to 1.3. The present disclosure also provides the polythiophene polymer and uses thereof.
Whitten, David G.↗
Substituted thiophene oligomers and polymers
The present disclosure provides an antimicrobial substrate including a substrate and a polythiophene polymer. The polythiophene polymer has a number of repeated monomer units from n is 5-14 or 30 to 120, a number average molecular weight (Mn) from 1,000 to 4,000 or 10,000 to 40,000; and a polydispersity index (PDI) from 1 to 1.3. The present disclosure also provides the polythiophene polymer and uses thereof.
Whitten, David G.↗
Kinetically Controlled Formation of Semi-crystalline Conjugated Polymer Nanostructures
Conjugated polymer (CP) materials that are considered as an attractive choice for various electronic and optoelectronic applications possess highly heterogeneous complex structures that can span several orders of magnitude in length scale. This is due to the intricate coupling effects of weak secondary interactions and entropic forces that determine molecular organization in bulk polymer materials. Understanding the influence of molecular interactions on the emergence and evolution of nano- and microscale structures is of paramount importance to the guided design and development of condensed CP materials. Such understanding is even more critical for the rational design of hierarchical systems away from equilibrium, where weak molecular interactions can guide the system along competing kinetic pathways toward local energy minima and metastable architectures. In this work, we studied a promising concept for accessing various kinetically stabilized semi-crystalline CP nanostructures that are formed in the process of controlled chain-growth Kumada catalyst-transfer polymerization initiated by a small-molecule catalytic species which can exist in equilibrium between free and aggregated states. Specifically, we chose a small-molecule perylenedicarboximide (PDCI) polymerization catalytic initiator which has a strong tendency toward reversible supramolecular assembly–disassembly that can be controlled by temperature. Addition of a thiophene monomer to a solution of the PDCI initiator starts the chain-growth polymerization process, which produces distinct nanoscale semi-crystalline polythiophene structures formed under predominant kinetic control. Furthermore, we demonstrated that, depending on the reaction temperature (which affects the fine balance between the position of PDCI assembly–disassembly equilibrium, rate of polymerization, and solvent–solute interactions for the growing polythiophene chains), a range of kinetically trapped hierarchically organized semi-crystalline CP systems with substantially varying optoelectronic properties could be obtained. In addition to spectroscopic and electron microscopic studies, in order to better reveal the structural aspects of the generated polymer nanoscale systems, we carried out a series of X-ray diffraction and neutron scattering experiments which indicated complex hierarchical organization in these kinetically stabilized CP assembled materials. We expect that this in situ polymerization-based approach can lead to a general way to expand access to various semi-crystalline CP nanostructured materials with broadly tunable electronic and optical properties.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Etching and polymerization reactions of alkoxythiophenes in HKUST-1: choosing between filled and core–shell MOF/polymer composite structures
Neat alkoxythiophenes react with MOF HKUST-1 to form a core–shell composite where the HKUST-1 surface is coated with conjugated polymer, while hexane solutions of thiophenes form a filled composite with polythiophene inside MOF pores.
James, William↗
Engineering donor–acceptor conjugated polymers for high-performance and fast-response organic electrochemical transistors
To date, high-performance organic electrochemical transistors (OECTs) have mostly been based on polythiophene systems. Donor–acceptor (D–A) conjugated polymers are expected to be promising materials for OECTs owing to their high mobility and comparatively low crystallinity (good for ion diffusion). However, the OECT performance of D–A polymers lags far behind that of the polythiophenes. Here we synergistically engineered the backbone and side chain of a series of diketopyrrolopyrrole (DPP)-based D–A polymers and found that redox potential, molecular weight, solution processability, and film microstructures all have a severe impact on their performance. After systematic engineering, P(bgDPP-MeOT2) exhibited the best figure-of-merit (μC*) of 225 F cm -1 V -1 s -1 , amongst the highest performance of the reported D–A polymers. Besides, the DPP polymers exhibited high hole mobility of over 1.6 cm 2 V -1 s -1 , leading to fast response OECTs with a record low turn-off response time of 30 μs. The polymer also exhibited good operation stability with a current retention of 98.8% over 700 electrochemical switching cycles. This work reveals the complexity and systematicness in the development of D–A polymer based high-performance OECTs.
36 MATERIALS SCIENCE↗
Organometallic Polymeric Conductors
For aerospace applications, the use of polymers can result in tremendous weight savings over metals. Suitable polymeric materials for some applications like EMI shielding, spacecraft grounding, and charge dissipation must combine high electrical conductivity with long-term environmental stability, good processability, and good mechanical properties. Recently, other investigators have reported hybrid films made from an electrically conductive polymer combined with insulating polymers. In all of these instances, the films were prepared by infiltrating an insulating polymer with a precursor for a conductive polymer (either polypyrrole or polythiophene), and oxidatively polymerizing the precursor in situ. The resulting composite films have good electrical conductivity, while overcoming the brittleness inherent in most conductive polymers. The highest conductivities reported (approximately 4/Scm) were achieved with polythiophene in a polystyrene host polymer. The best films using a polyamide as base polymer were four orders of magnitude less conductive than the polystyrene films. The authors suggested that this was because polyimides were unable to swell sufficiently for infiltration of monomer as in the polystyrene. It was not clear, however, if the different conductivities obtained were merely the result of differing oxidation conditions. Oxidation time, temperature and oxidant concentration varied widely among the studies.
Source record↗
Double Doping of Semiconducting Polymers Using Ion-Exchange with a Dianion
The interactions between counterions and electronic carriers in electrically doped semiconducting polymers are important for delocalization of charge carriers, electronic conductivity, and thermal stability. The introduction of a dianions in semiconducting polymers leads to double doping where there is one counterion for two charge carriers. Double doping minimizes structural distortions, but changes the electrostatic interactions between the carriers and counterions. Polymeric ionic liquids (PIL) with croconate dianions are helpful to investigate the role of the counterion in p-type semiconducting polymers. PILs prevent diffusion of the cation into the semiconducting polymers during ion exchange. The redox-active croconate dianions undergo ion exchange with doped semiconducting polymers depending on their ionization energy. Croconate dianions are found to reduce doped films of poly(3-hexyl thiophene), but undergo ion exchange with a polythiophene with tetraethylene glycol side chains, P(g 4 2T-T), that has a lower ionization energy. The croconate dianion maintains crystalline order in P(g 4 2T-T) and leads to a lower activation energy for the electrical conductivity than PF 6 – counterions. The control of the doping level with croconate allows optimization of the thermoelectric performance of the semiconducting polymer. Finally, the thermal stability of the doped films of P(g 4 2T-T) is found to depend strongly on the nature of the counterion.
36 MATERIALS SCIENCE↗
Lyotropic Liquid Crystal Mediated Assembly of Donor Polymers Enhances Efficiency and Stability of Blade-Coated Organic Solar Cells
Conjugated polymers can undergo complex, concentration-dependent self-assembly during solution processing, yet little is known about its impact on film morphology and device performance of organic solar cells. Herein, lyotropic liquid crystal (LLC) mediated assembly across multiple conjugated polymers is reported, which generally gives rise to improved device performance of blade-coated non-fullerene bulk heterojunction solar cells. Using D18 as a model system, the formation mechanism of LLC is unveiled employing solution X-ray scattering and microscopic imaging tools: D18 first aggregates into semicrystalline nanofibers, then assemble into achiral nematic LLC which goes through symmetry breaking to yield a chiral twist-bent LLC. The assembly pathway is driven by increasing solution concentration – a common driving force during evaporative assembly relevant to scalable manufacturing. This assembly pathway can be largely modulated by coating regimes to give 1) lyotropic liquid crystalline assembly in the evaporation regime and 2) random fiber aggregation pathway in the Landau–Levich regime. The chiral liquid crystalline assembly pathway resulted in films with crystallinity 2.63 times that of films from the random fiber aggregation pathway, significantly enhancing the T80 lifetime by 50-fold. The generality of LLC-mediated assembly and enhanced device performance is further validated using polythiophene and quinoxaline-based donor polymers.
14 SOLAR ENERGY↗
Observation of Weak Counterion Size Dependence of Thermoelectric Transport in Ion Exchange Doped Conducting Polymers Across a Wide Range of Conductivities
Conducting polymers are of interest for a broad range of applications from bioelectronics to thermoelectrics. The factors that govern their complex charge transport physics include the structural disorder present in these highly doped polymer films and the Coulombic interactions between the electronic charge carriers and the dopant counterions. Previous studies have shown that at low doping levels carriers are strongly trapped in the vicinity of the counterions, while at high doping levels charge transport is not limited by Coulombic trapping, which manifests itself in the conductivity being independent of the size of the dopant counterion. Here a recently developed ion exchange doping method is used to investigate the ion size dependence of a semicrystalline polythiophene–based model system across a wide range of conductivities. It is found that the regime in which the charge and thermoelectric transport is not or only weakly dependent on ion size, extends to surprisingly low conductivities. This surprising observation is explained by a heterogeneous doping that involves doping of the amorphous domains to high doping levels first before doping of the ordered, crystalline domains occurs. The study provides new insights into how the thermoelectric physics of conducting polymers evolves as a function of doping level.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Manipulating Conjugated Polymer Backbone Dynamics through Controlled Thermal Cleavage of Alkyl Side Chains
The morphological stability of an organic photovoltaic (OPV) device is greatly affected by the dynamics of donors and acceptors occurring near the device's operational temperature. These dynamics can be quantified by the glass transition temperature (T g ) of conjugated polymers (CPs). Because flexible side chains possess much faster dynamics, the cleavage of the alkyl side chains will reduce chain dynamics, leading to a higher T g . In this work, the T g s for CPs are systematically studied with controlled side chain cleavage. Isothermal annealing of polythiophenes featuring thermally cleavable side chains at 140 °C, is found to remove more than 95% of alkyl side chains in 24 h, and raise the backbone T g from 23 to 75 °C. Coarse grain molecular dynamics simulations are used to understand the T g dependence on side chain cleavage. X-ray scattering indicates that the relative degree of crystallization remains constantduring isothermal annealing process. The effective conjugation length is not influenced by thermal cleavage; however, the density of chromophore is doubled after the complete removal of alkyl side chains. Here, the combined effect of enhancing T g and conserving crystalline structures during the thermal cleavage process can provide a pathway to improving the stability of optoelectronic properties in future OPV devices.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Complex Relationship between Side-Chain Polarity, Conductivity, and Thermal Stability in Molecularly Doped Conjugated Polymers
Molecularly doped conjugated polymers with polar side chains are an emerging class of conducting materials exhibiting enhanced and thermally stable conductivity. In this work, we study the electronic conductivity (σ) and the corresponding thermal stability of two polythiophene derivatives comprising oligoethylene glycol side chains: one having oxygen attached to the thiophene ring (poly(3-(methoxyethoxyethoxy)thiophene) (P3MEET)) and the other having a methylene spacer between the oxygen and the thiophene ring (poly(3-(methoxyethoxyethoxymethyl)thiophene) (P3MEEMT)). Thin films were vapor-doped with fluorinated derivatives of tetracyanoquinodimethane (FnTCNQ, n = 4, 2, 1) to determine the role of dopant strength (electron affinity) in maximum achievable σ. Specifically, when vapor doping with F 4 TCNQ, P3MEET achieved a substantially higher σ of 37.1 ± 10.1 S/cm compared to a σ of 0.82 ± 0.06 S/cm for P3MEEMT. Structural characterization using a combination of X-ray and optical spectroscopy reveals that the higher degree of conformational order of polymer chains in the amorphous domain upon doping with F 4 TCNQ in P3MEET is a major contributing factor for the higher σ of P3MEET. Additionally, vapor-doped P3MEET exhibited superior thermal stability compared to P3MEEMT, highlighting that the presence of polar side chains alone does not ensure higher thermal stability. Molecular dynamics simulations indicate that the dopant–side-chain nonbond energy is lower in the P3MEET:F 4 TCNQ mixture, suggesting more favorable dopant–side-chain interaction, which is a factor in improving the thermal stability of a polymer/dopant pair. Our results reveal that additional factors such as polymer ionization energy and side-chain–dopant interaction should be taken into account for the design of thermally stable, highly conductive polymers.
36 MATERIALS SCIENCE↗
Impact of Side Chain Chemistry on Lithium Transport in Mixed Ion–Electron-Conducting Polymers
We discuss how typical design strategies for mixed ion-electron conduction in polymers have focused on overall ionic conductivity, without specificity for anion vs. cation conduction. Here, we demonstrate that side chain chemistry can be used to control Li+ conductivity in semiconducting polymers. This design principle is significant for applications which require Li+ specific transport, such as Li-ion batteries. We show that a polythiophene functionalized with an ionic liquid side chain demonstrates higher conductivity and lithium transference than a more commonly studied ether-functionalized P3AT derivative. Poly(3-(6’-(N-methylimidazolium) hexyl)thiophene TFSI–) (P3HT-Im+TFSI–) can solvate and conduct ions up to salt concentrations of r=1.0 (where r = [moles of salt]/[moles of monomer]) while achieving ionic conductivity of ≈10–3 S/cm at 80°C, and a lithium transference number of 0.36. On the other hand, poly(3¬-(methoxyethoxyethoxymethyl) thiophene) (P3MEEMT) shows a peak conductivity of ≈10–5 S/cm at r=0.05 and 80°C, with near zero lithium transport. This work shows that multiple high dielectric moieties can be used to drive ion conduction in semiconducting polymers, but diffuse, cationic side chains such as imidazolium are preferred for Li-ion conduction.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Resonant X-ray Diffraction Reveals the Location of Counterions in Doped Organic Mixed Ionic Conductors
Organic mixed ionic–electronic conductors (OMIECs) have the potential to enable diverse new technologies, ranging from novel in situ biosensors to flexible energy storage devices and neuromorphic computing platforms. However, their complex behavior in functional films involving electrolyte-induced swelling, ion ingress, and electrochemical doping inhibits rational material design. Of critical importance is an understanding of the specific location of the ions in the volumetrically doped material, yet this information is not readily available. Here, in this report, we present the use of grazing- incidence resonant X-ray diffraction (RXRD, also known as anomalous diffraction) at S and Cl K-edges to determine the structure of a doped, prototypical, semicrystalline polymer OMIEC based on oligo(ethylene glycol) substitution of regioregular polythiophene. The RXRD measurement provides two key insights. Quantitative analysis of the RXRD allows the determination of the position of the ion relative to the polymer backbone in the crystalline regions. We find that the anion is relatively distant from the backbone, nearer to the lamella mid-plane naively in conflict with expected Coulombic attraction between the ion and the doped polymer polaron. Comparison of RXRD to Cl – fluorescence (total Cl – ) allows determination of the relative order of doping between the crystalline and amorphous regions. We find preferential doping of the crystalline regions. Both insights, the preferential doping of crystals at low potential and the specific location of the counterion with respect to the polymer backbone, are critical to developing a microscopic understanding of transport in OMIECs.
36 MATERIALS SCIENCE↗