Search NASA⌕ Search

SEARCH · Search NASA

Results for “preforms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Theoretical considerations for Reaction-Formed Silicon Carbide (RFSC) formation by molten silicon infiltration into slurry-derived preforms

For reaction-formed silicon carbide (RFSC) ceramics produced by silicon melt infiltration of porous carbon preforms, equations are developed to relate the amount of residual silicon to the initial carbon density. Also, for a slurry derived preform containing both carbon and silicon powder, equations are derived which relate the amount of residual silicon in the RFSC to the relative density of the carbon in the preform and to the amount of silicon powder added to the slurry. For a porous carbon preform that does not have enough porosity to prevent choking-off of the silicon infiltration, these results show that complete silicon infiltration can occur by adding silicon powder to the slurry mixture used to produce these preforms.

Behrendt, D. R.↗

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

Innovative design concepts and cost effective fabrication processes were developed for damage tolerant primary structures that can perform at a design ultimate strain level of 6000 micro inch/inch. Attention focused on the use of textile high performance fiber reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials and/or processes methods is described: fabricated using IM7 angle interlock 0 to 90 deg woven preforms with + or - 45 deg plies stitched with Toray high strength graphite thread and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; fabricated using G40-800 knitted/stitched preforms using RTM and Tactix 123/H41 epoxy; and fabricated preforms using AS4(6K)/PEEK 150 g commingled angle interlock 0 to 90 deg woven preforms with + or - 45 deg commingled plies stitched using high strength graphite thread and processed by consolidation. Structural efficiency, processability, and acquisition cost are compared.

Suarez, J.↗

Reactive melt infiltration of silicon-molybdenum alloys into microporous carbon preforms

Investigations on the reactive melt infiltration of silicon-1.7 and 3.2 at.% molybdenum alloys into microporous carbon preforms have been carried out by modeling, differential thermal analysis (DTA), and melt infiltration experiments. These results indicate that the pore volume fraction of the carbon preform is a very important parameter in determining the final composition of the reaction-formed silicon carbide and the secondary phases. Various undesirable melt infiltration results, e.g. choking-off, specimen cracking, silicon veins, and lake formation, and their correlation with inadequate preform properties are presented. The liquid silicon-carbon reaction exotherm temperatures are influenced by the pore and carbon particle size of the preform and the compositions of infiltrants. Room temperature flexural strength and fracture toughness of materials made by the silicon-3.2 at.% molybdenum alloy infiltration of medium pore size preforms are also discussed.

Singh, M.↗

Preform spar cap for a wind turbine rotor blade

A spar cap for a wind turbine rotor blade. The spar cap may include multiple preform components. The multiple preform components may be planar sheets having a swept shape with a first end and a second end. The multiple preform components may be joined by mating the first end of a first preform component to the second end of a next preform component, forming the spar cap.

17 WIND ENERGY↗

A numerical Bayesian-calibrated characterization method for multiscale prepreg preforming simulations with tension-shear coupling

We report that carbon fiber reinforced plastics (CFRPs) are attracting growing attention in industry because of their enhanced properties. Preforming of thermoset carbon fiber prepregs is one of the most common production techniques of CFRPs. To simulate preforming, several computational methods have been developed. Most of these methods, however, obtain the material properties directly from experiments such as uniaxial tension and bias-extension where the coupling effect between tension and shear is not considered. Neglecting this coupling effect deteriorates the prediction accuracy of simulations. To address this issue, we develop a Bayesian model calibration and material characterization approach in a multiscale finite element preforming simulation framework that utilizes mesoscopic representative volume element (RVE) to account for the tension-shear coupling. A new geometric modeling technique is first proposed to generate the RVE corresponding to the close-packed uncured prepreg. This RVE model is then calibrated with a modular Bayesian approach to estimate the yarn properties, test its potential biases against the experiments, and fit a stress emulator. Finally, the predictive capability of this multiscale approach is further demonstrated by employing the stress emulator in the macroscale preforming simulation which shows that this approach can provide accurate predictions.

36 MATERIALS SCIENCE↗

Tailored Fiber Placement for Complex Preforms

Tailored Fiber Placement (TFP) offers a novel approach to optimize fiber architecture for the fabrication of complex, structural parts not traditionally suitable for advanced composites. This technology not only offers new routes for weight reduction via metal substitution, it also offers cost reduction through minimization of material scrap and reduced labor. This reduction in component weight leads to increased fuel efficiency, and reduced production energy consumption, thereby, helping to achieve the stated IACMI technical goals. This technology leverages centuries of manufacturing development in support of the textile and embroidery industry. One major drawback to this technology is the lack of commercial or non- proprietary structural performance data and robust analytical tools used to optimize fiber architecture and predict performance. This project was structured to utilize common sub-element features to validate analytical performance tools, generate performance data, and gather cost and performance data on components of interest. This project was designed to give industry sponsors the confidence and ability to take full advantage of TFP to fabricate primary, highly loaded structure and integrate features such as metallic fasteners. The project focused principally on the use of high strength carbon fiber, such as T700, and the use of aerospace epoxy resin matrix to primarily support development of new composite applications in vehicle, aerospace, and industrial markets. This project applied previously developed analytical tools to predict the performance of TFP produced parts. This work focused on developing the pipeline to characterize material in order to accurately predict component performance when modifying the TFP print paths and stitch density. This focused on experimental characterization via standardized ASTM testing, alongside experimental testing of more representative service components by testing curved beam strength, beam shear performance, a large scale TFP lug, and ultimately designing a fully TFP clip bracket that reduced weight and cost compared to a traditional metallic component. The new knowledge gained from this program included: 1) development and demonstration of novel analytical tools applied to analysis of TFP preforms; 2) development and demonstration of a building block approach using coupons and sub-elements to optimize the design of a more complex component; 3) demonstration that optimized fiber orientation using TFP can exceed performance of conventional textile composite materials and can open new applications currently limited to metallic components; 4) Demonstration of performance and cost benefits of the TFP process as compared to metallic and conventional textile composites. Recommendations for follow-on work include development of design allowables to assess the impact of high temperature/moisture exposure or saturation during loading, tracking the impact of stitching needle wear on the performance of parts and ability to stitch thicker preforms, using TFP preforms as local reinforcement at areas of bearing or complex loading, and topology optimization of components by tow steering. The expertise developed during the course of this project can be leveraged to provide commercial engineering design and fabrication services using TFP. UDRI is in the process of formalizing their partnership with Spintech, who will serve as the commercialization partner for this technology and provide molding services and deliver finished components to the end user. UDRI will continue to produce the preforms until the economics allow Spintech to procure its own TFP equipment or lease UDRI equipment, at which point UDRI will step away from manufacture and serve as the engineering and design lead on product development.

36 MATERIALS SCIENCE↗

Stiffener Jumping for Unitized Stitched Composite Preform Manufacturing

A single-sided stitching head is used to assemble unitized three-dimensional preforms using the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) robotic manufacturing system. Typically, assembly of a preform includes a “skin” that is stiffened by stiffener elements stitched to the skin. The single-sided stitching head has two needles that pass through the preform from the same side to form the stitch, typically from the smooth outer surface so the needles penetrate through the preform towards the stiffener side. The single-sided head cannot stitch across stiffening elements (e.g., stringer, frame, integral cap, etc.) because the needles would penetrate into the stiffener web, which would not allow the stitch form because the thread movement would be impeded. As a result, stitching seams cannot cross stiffening elements, and therefore are very short and must remain in the skin/flange connections within the space between the stiffening element webs. Each short segment requires a stop and cut process that takes a significant amount of time. A stiffener jumping stitching method was developed that eliminates the need to cut and restart seams when encountering a stiffener, thus providing a long, continuous seam with a significant reduction in stitching time by eliminating cutting operations and associated excess thread end trimming. This stiffener jumping process places what could be considered a very long stitch that bridges the stiffener to connect the end of one segment of the seam with the beginning of the next segment of the seam to provide a longer continuous seam. As a result, all intermediate thread cuts that would be done at the end of each individual segment of the seam are eliminated, with only a single cut at the end of the seam. The process and programming requirements for carrying out the stiffener jumping stitching approach are presented in this paper. Using the presented stiffener jumping approach to produce the long continuous seams, the stitching time for a representative commercial transport unitized stiffened wing cover panel can possibly be reduced by at least 25 percent.

stitched↗

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr{sub 2}Cu into Porous Preforms from Partially Carburized W Powders

W-ZrC composites with different W contents from 48 to 73 vol.% have been synthesized by reactive melt infiltration of Zr{sub 2}Cu melt into porous preforms from partially carburized W powders at 1300 °C for 1 h in vacuum. The influences of carbon content and porosity in the preforms on microstructure and mechanical properties of W-ZrC composites are investigated. Cold isostatic pressing followed by pre-sintering process is used to produce porous preforms with suitable porosities of 53.6-47% under a pressure of 100 MPa to allow sufficient penetration of Zr{sub 2}Cu melt into the preforms. Small amounts of Cu-rich phases form in the synthesized W-ZrC composites after a complete reaction of y/2xZr{sub 2}Cu(l) + WC{sub y}(s) = y/xZrC{sub x}(s) + W(s) + y/2xCu(l). These Cu-rich phases are distributed not only at the phase boundaries of W matrix and ZrC grains, but also in the interior of ZrC{sub x} grains. With decreasing W content from 73 to 48 vol.% in the W-ZrC composites, the flexural strength and fracture toughness increase from 519 to 657 MPa and from 9.1 to 10.6 MPa m{sup 1/2}, respectively.

36 MATERIALS SCIENCE↗

W-ZrC composites prepared by reactive melt infiltration of Zr 2 Cu alloy into binder jet 3D printed WC preforms

W-ZrC composites were successfully prepared by reactive melt infiltration (RMI) of stoichiometric and excess amounts of Zr 2 Cu into sintered and un-sintered WC preforms made from binder jet 3D printing. The focus of this work was to study the conversion of reactant powders and liquid infiltrant with varying preform density and infiltrant amount by controlling the processing time to reach high conversion yield while understanding the phase composition, microstructure, and hardness. To investigate the effect of time, the reactive melt infiltration was conducted at 1400 °C for 2, 4 and 8 h in a furnace with 96% Ar - 4% H2 gas atmosphere. The increase in reaction time from 2 to 8 h increased the W and W 2 C phase contents and decreased the ZrC phase content when using sintered WC preforms. Samples prepared from un-sintered WC preforms exhibited improved reactive melt infiltration compared to sintered samples, and there was no detectable W 2 C phase and nearly full consumption of WC. Similar to sintered WC samples, the content of W and ZrC phases increased with the increase in time from 2 to 8 h. The interfaces and phases at reaction interfaces were investigated using electron diffraction analysis and S/TEM-EDS to understand material stability; the phases were identified and consistent with XRD analysis. Additionally, there was no Cu present at the interfaces. Increasing the amount of infiltrant led to better reactive melt infiltration. In general, the hardness increased with reaction time and the highest Vickers hardness was found in the W-ZrC sample formed from sintered WC reacted with excess Zr 2 Cu. Finally, this research addresses the critical comparison of sintering and RMI time and shows that by using un-sintered samples for 8 h we are able to achieve W-ZrC composites with fewer undesired phases.

36 MATERIALS SCIENCE↗

Effect of particle size on pore three-dimensional characteristics of SiCp preforms by X-ray micro-computed tomography

Highlights: • X-ray μ-CT was used to characterize 3D structures of the pores in SiCp preforms. • 3D pore network models of the pore structure were extracted and analyzed. • With the increase of particle size, the homogeneity of pore distribution decreased. • Small particles in large spaces of coarse particles decreased preform connectivity. - Abstract: Silicon-carbide particle (SiC{sub p}) preforms with particle sizes of 20, 50, 100 and 150 μm were prepared by compression mold forming and heat treatment. A high resolution (~ 1.0 μm) three-dimensional (3D) X-ray micro-computed tomography (X-ray μ-CT) combined with 3D pore-network models were used to study the effect of particle size on 3D characteristics and spatial structures of pores in the preforms. The results demonstrated that as the particle size increased, the gap expansion caused by burning of starch reduced. When the particle size increased from 20 to 100 μm, the average areal porosity, homogeneity of pore distribution, connectivity, the numbers of small pores and throats, and average pore coordination number decreased; the average effective sizes of pores and throats increased. When the particle size further increased to 150 μm, the large gaps were filled by small particles resulted from the broken coarse particles, which decreased the homogeneity and connectivity of pores. As a result, the pore-network analysis shows that the numbers of small pores and throats and average pore coordination number increased.

36 MATERIALS SCIENCE↗

Formation mechanisms of precursors of radiation-induced color centers during fabrication of silica optical fiber preform

Samples in the form of transverse slices of rods and optical fiber preforms made from the high-hydroxyl KU-1 and low-hydroxyl KS-4V silica by the plasma outside deposition (POD) method are {gamma}-irradiated to a dose of {approx}1 MGy (SiO{sub 2}). Next, the radial dependences of the radiation-induced nonbridging oxygen hole center (NBOHC) and E'-center (three-coordinated silicon) in the samples are constructed by measuring the amplitudes of their 4.8 and 5.8 eV absorption bands, respectively. Based on the analysis of these radial dependences and considering the temperature and duration of the preirradiation heat treatment of the rods and preforms at the POD-installation, we determine the ratio of the oscillator strengths of the above bands and the microscopic thermoinduced processes occurring during preform fabrication and producing precursors of the radiation-induced NBOHC and E'-center. These processes are found to be associated with the escape of either H{sub 2} or H{sub 2}O from neighboring hydroxyl groups, and, therefore, can occur in high-hydroxyl silica only. It is concluded that enhancement of the radiation resistance of high-hydroxyl silica optical fibers requires decreasing the temperature and duration of the preform fabrication process, in particular, changing from the POD-technology to the low-temperature plasmachemical vapor deposition (PCVD) or surface PCVD (SPCVD)-technology.

36 MATERIALS SCIENCE↗

Preformation of clusters in heavy nuclei and cluster radioactivity

Within the preformed cluster model approach, the values of the preformation factors have been deduced from the experimental cluster decay half-lives assuming that the decay constant of the heavy-ion emission is the product of the assault frequency, the preformation factor and the penetrability. The law according to which the preformation factors follow a simple dependence on the mass of the cluster was confirmed. Then predictions for some of the most possible cluster decays are provided.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Calculation of {alpha} preformation for nuclei near N=162 and N=184

The {alpha} preformation factor and the penetration probability are carefully analyzed for heavy and superheavy even-even nuclei. The penetration probability of an {alpha} cluster in the parent nucleus is calculated within the WKB approximation, whereas the nuclear potential between an {alpha} cluster and the daughter nucleus is obtained in the frame of a double-folding model with a density-dependent nucleon-nucleon interaction, in which the zero-range exchange term is supplemented. The {alpha} preformation factors in different shell regions are compared. It is shown that shell effects play an important role in {alpha} preformation. The preformation factor can supply information on the nuclear structure, and the penetration probability mainly determines the {alpha}-decay half-life. The results indicate that the deformed-subshell region at N=162 is different from that at N=152, and Z=114 and N=184 may lie in the closed-shell region.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Chemical vapor infiltration of additively manufactured preforms: Pore-resolved simulations and experimental validation

The densification of additively manufactured porous preforms by chemical vapor infiltration (CVI) is studied using pore-resolved simulations and experiments. Experimentally, 3D printed silicon carbide (SiC) preforms are subject to CVI synthesis using methyltrichlorosilane (MTS) precursor to obtain high purity SiC/SiC composites. Optical images of the cross sections of the processed preforms are analyzed to obtain the spatial porosity distribution. The numerical method is based on a level set formulation to capture the spatial distribution and time evolution of the pore scale microstructural characteristics. The coupled transport and kinetic effects are represented using a dimensionless Thiele modulus. Simulations are initialized using representative synthetic preform geometries comprising of packed particles based on the size distribution of the powder used for 3D printing. The simulation results are validated against the experimental observations in terms of total density and the distribution of residual porosity. The densification characteristics, porosity classification, concentration profiles, and structure functions are analyzed as functions of processing temperature and Thiele modulus.

36 MATERIALS SCIENCE↗

Analysis and test of bonded single lap joints with preformed adherends

A theoretical and experimental study has been conducted to investigate the load transfer of a single lap joint where the adherends have been preformed so that the angle between the line of action of the applied in-plane force and the bond line is reduced. The preforming of the adherend reduces the moment resultant in the adherend at the edge of the overlap region which reduces both the maximum peel and shear stresses in the adhesive, and gives a more uniform shear distribution in the adhesive. An increase in static load transfer of up to 120 percent has been shown, and several orders of magnitude increase in fatigue life have been achieved with modest preform angles. Thus, sizeable benefits can be obtained in the fatigue life or additional load capacity of bonded single lap joints by preforming the adherends.

Sawyer, J. W.↗

Comparison of resin film infusion, resin transfer molding, and consolidation of textile preforms for primary aircraft structure

Under NASA's Novel Composites for Wing and Fuselage Applications (NCWFA) Program, Grumman is developing innovative design concepts and cost-effective fabrication processes for damage-tolerant primary structures that can perform at a design ultimate strain level of 6000 micro-inch/inch. Attention has focused on the use of textile high-performance fiber-reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low-cost resin film infusion (RFI) and resin transfer molding (RTM) processes, and thermoplastic forming concepts. The fabrication of wing 'Y' spars by four different materials/processes methods is described: 'Y' spars fabricated using IM7 angle interlock 0/90 deg woven preforms with +/- 45 deg plies stitched with Toray high-strength graphite thread and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RFI and 3501-6 epoxy; 'Y' spars fabricated using G40-800 knitted/stitched preforms and processed using RTM and Tactix 123/H41 epoxy; and 'Y' spars fabricated using AS4(6k)/PEEK 150-g commingled angle interlock 0/90 deg woven preforms with +/- 45 deg commingled plies stitched using high-strength graphite thread and processed by consolidation. A comparison of the structural efficiency, processability, and projected acquisition cost of these representative spars is presented.

Suarez, J.↗

Microstructure and Tensile Properties of BN/SiC Coated Hi-Nicalon, and Sylramic SiC Fiber Preforms

Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS) and 8-harness satin (8HS) Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0" fibers giving rise to hysteretic behavior, For the Hi-Nicalon preform specimens, the onset of "0" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. Transmission Electron Microscope (TEM) analysis indicates that the Chemical Vapor Infiltration (CVI) Boron Nitride (BN) interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating.

Bhatt, Ramakrishna T.↗

Microstructure and Tensile Properties of BN/SiC Coated Hi-Nicalon, and Sylramic SiC Fiber Preforms

Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS), and 8-harness satin (8HS). Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0 deg" fibers giving rise to hysteretic behavior. For the Hi-Nicalon preform specimens, the onset of "0 deg" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0 deg" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. TEM analysis indicates that the CVI BN interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating.

Bhatt, Ramakrishna T.↗