SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The report details a series of software tools and workflows to analyze surface deformation data obtained from InSAR, deformation evidence by earthquake, geological constraints, and reservoir management to define and monitor the geothermal reservoir.
The presence of compliant pores in rocks is important for understanding the stress–strain behaviors under different stress conditions. This paper describes findings on the effect of compliant pores on the mechanical behavior of a reservoir sandstone under hydrostatic and triaxial compression. Laboratory experiments were conducted at reservoir temperature on Weber Sandstone samples from the Rock Springs Uplift, Wyoming. Each experiment was conducted at three sequential stages: (stage 1) increase in the confining pressure while maintaining the pore pressure, (stage 2) increase in the pore pressure while maintaining the confining pressure, and (stage 3) application of the deviatoric load to failure. The nonlinear pore pressure – volumetric strain relationship governed by compliant pores under low confining pressure changes to a linear behavior governed by stiff pores under higher confining pressure. The estimated compressibilities of the matrix material in sandstone samples are close to the typical compressibility of quartz. Because of the change in pore structures during stage 1 and stage 2 loadings, the estimated bulk compressibilities of the sandstone sample under the lowest confining pressure decrease with increasing differential pressure. The increase in crack initiation stress is limited with increasing differential pressure because of similar total crack length governed by initial compliant porosity in sandstone samples.
Fluid injection and production related to energy recovery and other industrial operations alter the pressure and stress state of subsurface reservoirs which can lead to induced seismicity. Here, the primary goal is to investigate the hypothesis that the modulation of stress state in subsurface reservoirs through fluid injection/production operations can reduce the likelihood of inducing seismicity. Validation of this mitigation strategy will provide an active operational method to control induced seismicity in subsurface reservoir exploitations such as geothermal energy recovery and carbon storage. In this project, we analyze the relationship between extensive fluid production and the paucity of aftershock activity at the Coso Geothermal plant (CGP) following the 2019 Ridgecrest earthquake sequence, where high rates of aftershock triggering were expected. We developed a high-fidelity multiphase coupled thermo-hydro-mechanical (THM) model to simulate fluid injection/production activities at the CGP between 1986 and 2020. THM results of surface subsidence due to high rates of fluid production agree well with field observations from global positioning system (GPS) and interferometric synthetic aperture radar (InSAR). Subsequently, the variations of pore pressure, temperature and stress state were used to drive numerical earthquake simulations of the aftershock response to the 2019 Ridgecrest earthquakes. The earthquake simulations show that seismic quiescence may occur following the Ridgecrest event, depending on the initial stress state at the time of the mainshock and at the initiation of geothermal energy production. Seismic quiescence occurs in 20% of the cases we explored, where rates are decreased by 50% of the background rate in the two years following the mainshock. In circumstances where aftershock rates increase near the CGP following Ridgecrest, the average rate change is a factor of two larger than background rates from simulations with no operations. These findings indicate that unlike many other operations that bring faults closer to failure, operations at the CGP are acting to stabilize faults such that triggering in the current stress state is minimal.
Abstract The in‐situ stress state and geomechanical properties of hydrate‐bearing sediments impact hydrate formation and gas production strategies. We explore the uniaxial strain compression and stress evolution of natural hydrate‐bearing sandy‐silts from Green Canyon Block 955 in the deep‐water Gulf of Mexico. We performed constant rate of strain uniaxial strain experiments, interrupted by periods where we held the axial stress constant, to explore the vertical deformation and the evolution of the ratio of lateral to axial effective stress ( K 0 ) with time. The hydrate‐bearing sandy‐silt is stiffer and has a larger K 0 than the equivalent hydrate‐free sediment upon loading. During stress holds, the void ratio decreases sigmoidally with the log of time, and K 0 converges to isotropic conditions. We interpret that during loading, the hydrate bears the load and deforms. With time, the hydrate redistributes the load and K 0 increases. We used a viscoelastic model to describe the behavior. The model accurately captures deformation and K 0 trends but does not reproduce all the complex interactions of the hydrate with the porous skeleton. We anticipate that viscous effects within hydrate sediments will impact reservoir compression and stresses during production (hours to days), result in isotropic stress state over geological timescales, and explain the creeping movement in submarine landslides.
We develop well-completion surrogate models by taking an integrated workflow of hydraulic fracturing, flow, geomechanics, and machine learning simulation. There are three steps in the proposed workflow. First, history-matching processes are conducted with the field data including pumping and production data for characterization. Second, full-physics simulation is performed with various parameters of the field development (e.g., cluster spacing, clusters per stage, pumping rates and times, amount of proppant, and well spacing) to generate multiple simulation results by changing the parameters of the completion design with well-known hydraulic fracturing, reservoir, geomechanics simulators to calculate fracture geometry, reservoir depressurization, induced stress changes. The workflow is demonstrated over a field in the Southern Midland Basin. Here, we take two completion scenarios: a single well case followed by a multi-well case. Finally, a Long Short-Term Memory (LSTM) machine learning algorithm is employed to create surrogate models that can replicate the full-physics simulation results. Furthermore, results show that the trained models applied in the single well and multi-well cases for a particular geological system can provide good accuracy close to those provided by full-physics simulations. Specifically, the site-specific surrogate models can predict fracture parameters (length, height, and surface area) and cumulative production accurately with computational efficiency, suggesting our proposed workflow can be used as a pragmatic tool for expediting the well completion optimization process.
CO 2 injection in active oil fields is a technology proposed for industrializing carbon storage operations. However, monitoring CO 2 migration, oil recovery, and mechanical deformation within caprock and on faults is a challenging problem in large-scale storage-enhanced oil recovery operations due to intersecting faults, multiphase flow effects, and wells with complex production-injection schedule. We develop and demonstrate a methodology based on our coupled modeling framework to monitor the movement of CO 2 , hydrocarbons and water, and the associated evolution in mechanical stability of faults during CO 2 storage-enhanced oil recovery in the Farnsworth Unit oil field in Texas, United States. The methodology honors geological, geophysical, and production-injection data acquired in the field over six decades. Differential depletion from hydraulically isolated fault compartments followed by water and CO 2 injection-induced overpressure causes volumetric contraction and expansion of the reservoir, and changes in the total and effective stresses in the overburden-reservoir-underburden complex. CO 2 migrates upward to accumulate near top of the geologic structure, and water migrates downward to pressurize the faults. Three-dimensional changes in the pressure and stress fields in the system lead to changes in the shear and effective normal tractions on three major faults compartmentalizing the field. Evolution in fault tractions is used to compute the evolution in the Coulomb failure function of the faults to quantify induced-slip tendency under production and injection. We explain the spatial heterogeneity and time variability of Coulomb failure function in terms of well location heterogeneity and well rate variability.
Conference presentation at Carbon Capture, Utilization, and Storage (CCUS) Conference 2024, Houston, Texas, March 11–13, 2024. A screening-level regional evaluation of basement and mechanical overburden stress across the geologically diverse Plains CO 2 Reduction (PCOR) Partnership Initiative region was conducted. The main objective of the project was to assess potential basement fault reactivation and better understand technical uncertainties pertaining to CO 2 storage in candidate basal reservoirs.
A potential risk of injecting CO2 into storage reservoirs with marginal permeability (≲ 10 mD (1 mD = 10 –15 m 2 )) is that commercial injection rates could induce fracturing of the reservoir and/or the caprock. Such fracturing is essentially fluid-driven fracturing in the leakoff-dominated regime. Recent studies suggested that fracturing, if contained within the lower portion of the caprock complex, could substantially improve the injectivity without compromising the overall seal integrity. Modeling this phenomenon entails complex coupled interactions among the fluids, the fracture, the reservoir, and the caprock. Here, we develop a simple method to capture all these interplays in high fidelity by sequentially coupling a hydraulic fracturing module with a coupled thermal-hydrological-mechanical (THM) model for nonisothermal multiphase flow. The model was made numerically tractable by taking advantage of self-stabilizing features of leakoff-dominated fracturing. The model is validated against the PKN solution in the leakoff-dominated regime. Moreover, we employ the model to study thermo-poromechanical responses of a fluid-driven fracture in a field-scale carbon storage reservoir that is loosely based on the In Salah project's Krechba reservoir. The model reveals complex yet intriguing behaviors of the reservoir-caprock-fluid system with fracturing induced by cold CO 2 injection. We also study the effects of the in situ stress contrast between the reservoir and caprock and thermal contraction on the vertical containment of the fracture. The proposed model proves effective in simulating practical problems on length and time scales relevant to geological carbon storage.
The purpose of this paper is to analyze publicly available geomechanical data from two carbon storage sites in the Illinois Basin: the Illinois Basin-Decatur Project (IBDP) in Macon County, IL and the FutureGen2.0 project in Morgan County, IL, cancelled before injection began. This study estimates the magnitudes and directions of the least compressive principal stress gradient using hydraulic fracture-based stress measurement tests, borehole breakouts, and sonic logs in the Eau Claire Formation (primary confining zone) and the Mount Simon Sandstone (targeted reservoir). The range of stresses expected in the underlying Precambrian basement is also investigated. The evaluation of the state of stress is carried out in a probabilistic manner using the State of Stress Analysis Tool (SOSAT) developed under the National Risk Assessment Partnership (NRAP) program. Finally, the paper also provides a discussion on distinctions between fracture initiation pressure, propagation pressure, and fracture closure pressure, given that hydraulic fracture testing results show a significant difference between these three values. The discussion also addresses why the fracture closure pressure should be preferred in injection pressure determinations, a critical point in geological carbon storage projects.
This is a presentation on A Multi-Component Approach to Characterizing In-Situ Stress at the U.S DOE FORGE EGS Site: Laboratory, Modeling and Field Measurement project by Battelle [Columbus, OH], presented by Mark Kelley. The project's objective was to characterize stress in the Utah FORGE EGS reservoir using three methods: a laboratory rock-core stress estimation combined with a Machine Learning approach for estimation of in-situ stress from field sonic-log data, a field based in-situ measurement (min-frac) approach, and a modeling approach. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 7, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.
Abstract Hydraulic fracturing has unlocked vast amounts of hydrocarbons trapped within unconventional shale formations. This large-scale engineering approach inadvertently introduces microorganisms into the hydrocarbon reservoir, allowing them to inhabit a new physical space and thrive in the unique biogeochemical resources present in the environment. Advancing our fundamental understanding of microbial growth and physiology in this extreme subsurface environment is critical to improving biofouling control efficacy and maximizing opportunities for beneficial natural resource exploitation. Here, we used metaproteomics and exometabolomics to investigate the biochemical mechanisms underpinning the adaptation of model bacterium Halanaerobium congolense WG10 and mixed microbial consortia enriched from shale-produced fluids to hypersalinity and very low reservoir flow rates (metabolic stress). We also queried the metabolic foundation for biofilm formation in this system, a major impediment to subsurface energy exploration. For the first time, we report that H. congolense WG10 accumulates tyrosine for osmoprotection, an indication of the flexible robustness of stress tolerance that enables its long-term persistence in fractured shale environments. We also identified aromatic amino acid synthesis and cell wall maintenance as critical to biofilm formation. Finally, regulation of transmembrane transport is key to metabolic stress adaptation in shale bacteria under very low well flow rates. These results provide unique insights that enable better management of hydraulically fractured shale systems, for more efficient and sustainable energy extraction.
This is a presentation on the Experimental Determination and Modeling-Informed Analysis of Thermo-poromechanical Response of Fractured Rock for Application to Utah FORGE project by the University of Oklahoma, presented by Dr. Ahmad Ghassemi, McCasland Chair Prof. The project objective is to improve understanding and control of coupled thermo-poromechanical (or thermo-hydro-mechanical- TPM) processes in reservoir development, and to study any role in interpretations of the fracture closure. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 8, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.
This is a presentation on A Multi-Component Approach to Characterizing In-Situ Stress at the Utah FORGE Site: Laboratory Modelling and Field Measurements project by The University of Pittsburgh, presented by Andrew Bunger. The project characterizes the stress in the Utah FORGE EGS reservoir using three methods: Method 1: Demonstrate complimentary laboratory rock-core stress estimation combined with Machine Learning approach for measuring in-situ stress from field sonic log data; Method 2: Complete field based in-situ measurement (mini-frac); and Method 3: Develop a mechanics-based method for connection near wellbore stress measurements to stresses away from the well-bore. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 14, 2024.
The primary objectives of this project were to: develop a new, non-invasive method to define the orientation and magnitude of in-situ stresses in deep geologic formations (depths that exceed 1500 meters) considered for carbon dioxide (CO 2 ) sequestration; to demonstrate the method at a real field site; and, to extend current technical capabilities and reduce costs of acquiring information about deep-stress fields. This investigation was segmented into five tasks, including Project Management (Task 1) and four technical tasks (Tasks 2 through 5). The results of the technical tasks are described in this document.
We investigated the relationship between stratigraphy, stress, and microseismicity at the Hydraulic Fracture Test Site-1. The site comprises two sets of horizontal wells in the Wolfcamp shale and a deviated well drilled after hydraulic fracturing. Regional stresses indicate normal/strike-slip faulting with E-W compression. Stress measurements in vertical and horizontal wells show that the minimum principal stress varies with depth. Strata with high clay and organic content show high values of the least compressive stress, consistent with the theory of viscous stress relaxation. By integrating data from core, logs, and the hydraulic fracturing stages, we constructed a stress profile for the Wolfcamp sequence, which predicts how much pressure is required for hydraulic fracture growth. We applied the results to fracture orientation data from image logs to determine the population of pre-existing faults that are expected to slip during stimulation. We also determined microseismic focal plane mechanisms and found slip on steeply dipping planes striking NW, consistent with the orientations of potentially active faults predicted by the stress model. This case study represents a general approach for integrating stress measurements and rock properties to predict hydraulic fracture growth and the characteristics of injection-induced microseismicity.
During methane production in CBM reservoirs, the influence of proppant embedment and permeability damage cannot be neglected – especially where the wall-rock is soft. Effective stresses are elevated during methane recovery, increasing both normal loading stress and confinement and simultaneously overprinting sorption-induced volumetric strains. Experiments and analytic modeling are conducted to define key mechanisms controlling these competitive effects. We independently measure overall sample compaction (external LVDT) and local strain (strain gauge) in the matrix to deconvolve proppant embedment in a propped fracture for different conditions of confining stress. The results show symptomatic behaviors of elastic (shale) and elastoplastic (coal) responses of embedment. Different from shale, the evolution of embedment is convex upwards with increased stress where indented depth increases more rapidly as loading stress increases under constant confinement. In addition, a stress-hardening effect is found to play a pivotal role in determining the characteristics of indentation, which are examined in terms of evolution profiles, deformation regimes, embedment slopes, curvatures, yield points and irreversible indentations. Based on the experimental observations a semianalytical model predicts indentation and the evolution of propped permeability under recreated in-situ stress conditions. A simplified case study is conducted to further illustrate the evolution of aperture and permeability of a propped fracture in CBM reservoirs. The modeling results suggest that proppant embedment is significantly overestimated if the variable stress-hardening (VSH) effect is neglected, especially when effective stress is large. Moreover, a decrease in indentation depth possibly occurs during late stage methane production, resulting in a reversal/recovery in fracture closure. This is because desorption-induced shrinkage becomes the predominant effect, causing an increase in aperture and a reduction in the indented volume of proppant. The resulting recovery in permeability implies that the propped coal fracture has the potential to optimally facilitate methane production as a pathway, even at high closure stresses generated by methane drainage.
Understanding and predicting fracture propagation and subsequent fluid flow characteristics is critical to geoenergy technologies that engineer and/or utilize favorable geological conditions to store or extract fluids from the subsurface. Fracture permeability decreases nonlinearly with increasing normal stress, but the relationship between shear displacement and fracture permeability is less well understood. We utilize the new Geo–Reservoir Experimental Analogue Technology (GREAT cell), which can apply polyaxial stress states and realistic reservoir temperatures and pressures to cylindrical samples and has the unique capability to alter both the magnitude and orientation of the radial stress field by increments of 11.25° during an experiment. We load synthetic analogue materials and real rock samples to stress conditions representative of 500–1,000 m depth, investigate the hydraulic stimulation process, and then conduct flow experiments while changing the fluid pressure and the orientation of the intermediate and minimum principal stresses. High–resolution circumferential strain measurements combined with fluid pressure data indicate fracture propagation can be both stable (no fluid pressure drop) and unstable (fluid pressure drop). The induced fractures exhibit both opening and shear displacements during their creation and/or during fluid flow with changing radial stress states. Flow tests during radial stress field rotation reveal that fracture normal effective stress has first–order control on fracture permeability but increasing fracture offset can lead to elevated permeabilities at maximum shear stress. Here, the results have implications for our conceptual understanding of fracture propagation as well as fluid flow and deformation around fractures.