Search NASA⌕ Search

SEARCH · Search NASA

Results for “residual solvent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Influence of voids on the thermal and light stability of perovskite solar cells

The formation of voids in perovskite films close to the buried interface has been reported during film deposition. These voids are thought to limits the efficiency and stability of perovskite solar cells (PSCs). Here, we studied the voids formed during operation in perovskite films that were optimized during the solution deposition process to avoid voids. New voids formed during operation are found to assemble along grain boundaries at the bottom interface, caused by the loss of residual solvent and conversion of amorphous phase to crystalline phase. Unexpectedly, the formation of these voids did not negatively affect the stability of PSCs. Decreasing the amorphous region in perovskites by thermal annealing decreased the positive iodide interstitial density, and improved the light stability of PSCs. The annealed devices maintained 90% of their initial efficiency and light soaking for 1900 hours at open circuit condition under 1-sun illumination at 50°C.

14 SOLAR ENERGY↗
DOE OSTI2024

Two-dimensional heteronuclear single quantum coherence (HSQC) NMR spectra of lignin isolated from Populus trichocarpa residues after CELF pretreatment and CBP fermentation

Here we present a curated dataset of a series of two-dimensional heteronuclear single quantum coherence (HSQC) nuclear magnetic resonance (NMR) spectra of lignin isolated from a woody energy crop (Populus trichocarpa) residues after co-solvent enhanced lignocellulosic fractionation (CELF) pretreatment and consolidated bioprocessing (CBP) process. The natural poplar variant GW-9947 from the Center for Bioenergy Innovation (CBI) was used. The poplar was knife milled and passed through a 1 mm sieve. The CELF pretreatment was performed in a Parr autoclave reactor with 7.5 wt % solids loading, 0.5 wt% H2SO4 as catalyst at 150°C with 15, 25 and 30 minutes, respectively. Tetrahydrofuran was added in a 1:1 mass ratio with water as the pretreatment solvent. The residues from CELF pretreatment were then subjected to CBP using the bacterium C. thermocellum DSM 1313. CBP fermentations were performed at 60 °C in a shaker at 50 grams/L solids loadings. Lignin was isolated from the pretreated samples after ball-milling in a porcelain jar with ceramic balls via Retsch PM 200 at 580 rpm for 2.5 h followed by enzymatic hydrolysis in acetate buffer (pH 4.8, 50 °C) for 48 h. The lignin samples were characterized using 13C–1H HSQC experiments which were performed in a Bruker Avance III HD 500 MHz NMR spectrometer operating at a frequency of 125.12 MHz for the 13C nucleus. A standard Bruker pulse sequence was used on a Prodigy platform cryoprobe. The dry lignin samples were dissolved in deuterated dimethylsulfoxide for HSQC experiments. The spectra were acquired under the following acquisition conditions: 210 ppm spectral width in F1 (13C) dimension with 256 data points and 11 ppm spectral width in F2 (1H) dimension with 1024 data points, a 90° pulse, a one bond C–H coupling constant of 145 Hz, a 1.0 s pulse delay, and 64 scans. All the data was processed using the TopSpin 3.6 software (Bruker BioSpin). The NMR spectra provides structural characteristics information about lignin remaining in solids after CELF (150 °C with 15, 25 and 30 minutes) process and C. thermocellum CBP.

Lignin structure, HSQC, poplar, CELF, CBP, CBI↗
DOE OSTI2021

Subtask 2.6 – Optimization of Aerosol Mitigation Technology for Postcombustion CO 2 Capture

Growing concerns over the impact of CO 2 emissions from combustion sources on global climate change have prompted numerous research and development projects aimed at developing cost-effective technologies for CO 2 capture. One family of technologies being demonstrated at pilot and full scale globally is postcombustion CO 2 capture (PCCC) systems that employ amine-based solvents. The captured CO 2 can be compressed and permanently stored underground or used for enhanced oil recovery (EOR). The proximity of North Dakota’s lignite-fired fleet of power plants to potential CO 2 storage options creates a unique atmosphere for PCCC within the state. However, the aerosols present in lignite flue gas present a challenge for large-scale PCCC at North Dakota power plants. Aerosols can negatively impact the long-term performance of amine-based solvents for CO 2 capture. Amine-based solvents are volatile, and aerosols provide nucleation sites where amine vapors can condense. Because aerosols cannot be easily captured at the column outlet using conventional technologies, the amine-laden aerosols escape the system and lead to accelerated solvent losses. Moreover, aerosol components can chemically react with amines to form degradation products that can permanently deactivate the amine, cause fouling, and lead to hazardous emissions. Many of the elements that have been shown to catalyze solvent degradation are present in lignite coals and can exacerbate solvent replacement economics. Understanding this issue is critical to the implementation of solvent-based CO 2 capture systems as applied to lignite-fired generation systems. The Energy & Environmental Research Center (EERC) designed and carried out this project to optimize aerosol mitigation technology for PCCC at a lignite-fired power plant. To meet the goal of this project, the following objectives were identified: Determine the effectiveness of a wet electrostatic precipitator (WESP) on collection of aerosols at a low-rank coal-fired power station. Determine the impact of aerosols on the efficiency and degradation products of amine-based carbon capture systems fired with low-rank fuels. Work was conducted at Minnkota Power Cooperative’s (MPC’s) Milton R. Young (MRY) Station Unit 2 using a slipstream of flue gas from the outlet of the plant’s flue gas desulfurization (FGD) unit. To gather initial data for sizing and specifying a WESP for this system, a temporary pilot-scale WESP was rented and installed on-site. Several different conditions were tested to examine the impact of flow rate, voltage, and current on WESP performance. The WESP was effective at removing large particulate (>200 nm) but caused an increase in fine particulate (<75 nm). Fine particulate material at the inlet and outlet of the WESP was collected, analyzed, and showed that crystalline sulfates carried over from the plant’s FGD unit were being converted to fine aerosols and SO 2 was being converted to SO 3 through the WESP. Additionally, the high moisture content of the flue gas stream at this sample location also contributed to an overall increase in aerosol mass under some of the test conditions. Using the results from the rented WESP, the project team installed a smaller-scale WESP upstream of the EERC’s slipstream CO 2 capture system. Flue gas was routed through a pilot-scale FGD unit to remove SO 2 to very low levels (~1 ppm) and then through a direct contact cooler (DCC) to further cool the gas and to remove moisture. The gas exiting the DCC was then routed through the new WESP before passing to the CO 2 absorber columns. Fluor’s amine-based solvent was used to scrub CO 2 from the slipstream through a set of two absorber columns. The rich solvent was regenerated in a stripper column by heating to drive off captured CO 2 . The system operated using a catch-and-release method where the CO 2 was separated to provide data on the process, but the captured CO 2 was released back into the host site stack. Aerosols and sulfur species were measured at multiple locations throughout the pilot-scale system. The inlet FGD and DCC removed much of the particulate matter and gaseous sulfur upstream of the WESP. With this configuration, the WESP achieved >95% particulate capture. The new WESP did not show any of the increases in SO 3 or other aerosol species that had been consistently observed with the larger-scale WESP installed immediately downstream of the plant’s full-scale FGD unit. Particulate samples captured and analyzed from the WESP inlet did not show any presence of crystalline sulfate materials, indicating that the pilot-scale FGD and DCC were efficient at reducing carryover from the plant’s full-scale FGD unit. A set of parametric tests were conducted on the new WESP to assess the impacts of flow rate, voltage, number of online WESP fields, and gas-phase sulfur content on aerosol and sulfur transformations. The results showed that the WESP performed similarly well at all sets of conditions. Sulfur and particulate matter exiting the WESP were further reduced through the absorber column as the amine-based solvent captured some of the residual contaminants. Solvent analysis showed that these species were slowly concentrating in the solvent over the duration of the test. When the WESP was taken offline and the sulfur slip through the FGD allowed to rise, the sulfate content in the solvent rose sharply, showing that the extra FGD and WESP were effective at reducing sulfate and cation uptake. This would be expected to extend amine-based solvent life by slowing the formation of heat-stable salts and other degradation products. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission and MPC.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Lignin content of Populus trichocarpa residues after CELF pretreatment and CBP fermentation

Here we present a dataset of lignin content from a woody energy crop (Populus trichocarpa) residues after a series of co-solvent enhanced lignocellulosic fractionation (CELF) pretreatment and consolidated bioprocessing (CBP) process. The natural poplar variant GW-9947 from the Center for Bioenergy Innovation (CBI) was used. The poplar was knife milled and passed through a 1 mm sieve and CELF pretreatment was performed in a Parr autoclave reactor with 7.5 wt % solids loading, 0.5 wt% H2SO4 as catalyst at 150°C with 5, 15, 25 and 30 minutes, respectively. Tetrahydrofuran was added in a 1:1 mass ratio with water as the pretreatment solvent. The residues from CELF pretreatment were then subjected to CBP using the bacterium C. thermocellum DSM 1313. CBP fermentations were performed at 60 °C in a shaker at 50, 75, and 100 grams/L solids loadings. The Klason lignin was measured using a two-step acid hydrolysis process. In brief, the poplar samples were first hydrolyzed by 72 wt% sulfuric acid at 30 oC for an hour. The hydrolysates were then diluted to 4 wt% sulfuric acid using deionized water and subsequently autoclaved at 121 oC for 1 h. Upon the completion of the two-step hydrolysis, the resulting solution was cooled to room temperature and the precipitate was then filtered through a G8 glass fiber filter through a crucible, dried at oven for overnight, and weighed to get the Klason lignin content. The lignin data provides information about lignin content changes after CELF and C. thermocellum CBP process.

Lignin Populus trichocarpa CELF pretreatment CBP f↗
DOE OSTI2025

STEPs-SOL, a Peptoid Force Field Parameterization to Include Solvent Effects

As peptoids (N-substituted glycines) continue to gain popularity as a class of biomimetic polymers, the importance and demand for accurate force fields in molecular simulations also grow. Building on the vacuum-optimized Systematic and Extensible Force Field for Peptoids (STEPs) force field, here we present STEPs-SOL, a novel peptoid force field parametrization that effectively incorporates solvent effects to enhance the accuracy of peptoid simulations. The development of STEPs-SOL is based on the need for precise electrostatic modeling achieved through solvent-specific partial charge optimization. Here, our systematic approach significantly improves agreement with experimental measurements, reducing the mean absolute error in cis/trans ratio predictions (ΔG c/t ) by an average of 38% across multiple peptoid residues and solvent environments. This improved parametrization addresses computational challenges associated with nonbonded energies while maintaining a workflow that relies on high-level quantum mechanical data rather than depending solely on limited experimental equilibrium properties. By evaluating the effects of conformational bias in restrained electrostatic potential (RESP) charge generation and examining their impact on peptoid conformations in various solvents, we enhance our understanding of peptoid structural dynamics while providing a more accurate modeling framework.

force field↗
DOE OSTI2021

Direct detection of coupled proton and electron transfers in human manganese superoxide dismutase

Human manganese superoxide dismutase is a critical oxidoreductase found in the mitochondrial matrix. Concerted proton and electron transfers are used by the enzyme to rid the mitochondria of O 2 •– . The mechanisms of concerted transfer enzymes are typically unknown due to the difficulties in detecting the protonation states of specific residues and solvent molecules at particular redox states. Here, neutron diffraction of two redox-controlled manganese superoxide dismutase crystals reveal the all-atom structures of Mn 3+ and Mn 2+ enzyme forms. The structures deliver direct data on protonation changes between oxidation states of the metal. Observations include glutamine deprotonation, the involvement of tyrosine and histidine with altered pK a s, and four unusual strong-short hydrogen bonds, including a low barrier hydrogen bond. We report a concerted proton and electron transfer mechanism for human manganese superoxide dismutase from the direct visualization of active site protons in Mn 3+ and Mn 2+ redox states.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Variable domain mutational analysis to probe the molecular mechanisms of high viscosity of an IgG 1 antibody

Subcutaneous injection is the preferred route of administration for many antibody therapeutics for reasons that include its speed and convenience. However, the small volume limit (typically ≤2 mL) for subcutaneous delivery often necessitates antibody formulations at high concentrations (commonly ≥100 mg/mL), which may lead to physicochemical problems. For example, antibodies with large hydrophobic or charged patches can be prone to self-interaction giving rise to high viscosity. Here, we combined X-ray crystallography with computational modeling to predict regions of an anti-glucagon receptor (GCGR) IgG 1 antibody prone to self-interaction. An extensive mutational analysis was undertaken of the complementarity-determining region residues residing in hydrophobic surface patches predicted by spatial aggregation propensity, in conjunction with residue-level solvent accessibility, averaged over conformational ensembles from molecular dynamics simulations. Dynamic light scattering (DLS) was used as a medium throughput screen for self-interaction of ~200 anti-GCGR IgG 1 variants. A negative correlation was found between the viscosity determined at high concentration (180 mg/mL) and the DLS interaction parameter measured at low concentration (2–10 mg/mL). Additionally, anti-GCGR variants were readily identified with reduced viscosity and antigen-binding affinity within a few fold of the parent antibody, with no identified impact on overall developability. The methods described here may be useful in the optimization of other antibodies to facilitate their therapeutic administration at high concentration.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Computational design of highly signalling-active membrane receptors through solvent-mediated allosteric networks

Abstract Protein catalysis and allostery require the atomic-level orchestration and motion of residues and ligand, solvent and protein effector molecules. However, the ability to design protein activity through precise protein–solvent cooperative interactions has not yet been demonstrated. Here we report the design of 14 membrane receptors that catalyse G protein nucleotide exchange through diverse engineered allosteric pathways mediated by cooperative networks of intraprotein, protein–ligand and –solvent molecule interactions. Consistent with predictions, the designed protein activities correlated well with the level of plasticity of the networks at flexible transmembrane helical interfaces. Several designs displayed considerably enhanced thermostability and activity compared with related natural receptors. The most stable and active variant crystallized in an unforeseen signalling-active conformation, in excellent agreement with the design models. The allosteric network topologies of the best designs bear limited similarity to those of natural receptors and reveal an allosteric interaction space larger than previously inferred from natural proteins. The approach should prove useful for engineering proteins with novel complex protein binding, catalytic and signalling activities.

Chemistry↗
DOE OSTI2024

A tailored deep eutectic solvent for high-yield conversion of poplar residues to bio-based building blocks at mild conditions

The generation of condensed compounds in a deep eutectic solvent (DES) pretreatment has become a paramount factor that inhibits the further conversion of pretreated cellulose-rich substrate. Here, this study proposed a novel three-constituent DES system for the value-added utilization of poplar residues by efficiently suppressing hemicellulose derived condensation reactions. The results showed that adding ethanol into the DES system could effectively deconstruct the recalcitrant structure of poplar residues, simultaneously hindering the condensed composition formation. Under optimum ethanol addition (30%), the maximum xylan and lignin removal of 87.94% and 90.99% could be achieved, with more than 90.47% of glucan being preserved. With this, the glucan enzymatic hydrolysis efficiency was remarkably improved to 100% under the pretreatment conditions of 100 °C for 60 min, which was 84.69 times higher than the regular DES-pretreated poplar residues (1.17%). The working mechanism of relieving condensation reactions was characterized by Py-GC–MS, NMR, SEM, FTIR, and others. The results demonstrated that the addition of ethanol could regulate the degradation/conversion pathway of hemicellulose and lignin precipitation, thus inhibit the formation of condensed compounds during the pretreatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A Highly Ordered Nitroxide Side Chain for Distance Mapping and Monitoring Slow Structural Fluctuations in Proteins

Abstract Site-directed spin labeling electron paramagnetic resonance (SDSL-EPR) is an established tool for exploring protein structure and dynamics. Although nitroxide side chains attached to a single cysteine via a disulfide linkage are commonly employed in SDSL-EPR, their internal flexibility complicates applications to monitor slow internal motions in proteins and to structure determination by distance mapping. Moreover, the labile disulfide linkage prohibits the use of reducing agents often needed for protein stability. To enable the application of SDSL-EPR to the measurement of slow internal dynamics, new spin labels with hindered internal motion are desired. Here, we introduce a highly ordered nitroxide side chain, designated R9, attached at a single cysteine residue via a non-reducible thioether linkage. The reaction to introduce R9 is highly selective for solvent-exposed cysteine residues. Structures of R9 at two helical sites in T4 Lysozyme were determined by X-ray crystallography and the mobility in helical sequences was characterized by EPR spectral lineshape analysis, Saturation Transfer EPR, and Saturation Recovery EPR. In addition, interspin distance measurements between pairs of R9 residues are reported. Collectively, all data indicate that R9 will be useful for monitoring slow internal structural fluctuations, and applications to distance mapping via dipolar spectroscopy and relaxation enhancement methods are anticipated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Stable binding to phosphatidylserine-containing membranes requires conserved arginine residues in tandem C domains of blood coagulation factor VIII

At sites of vascular damage, factor VIII (fVIII) is proteolytically activated by thrombin and binds to activated platelet surfaces with activated factor IX (fIXa) to form the intrinsic “tenase” complex. Previous structural and mutational studies of fVIII have identified the C1 and C2 domains in binding to negatively charged membrane surfaces through β-hairpin loops with solvent-exposed hydrophobic residues and a ring of positively charged basic residues. Several hemophilia A-associated mutations within the C domains are suggested to disrupt lipid binding, preventing formation of the intrinsic tenase complex. In this study, we devised a novel platform for generating recombinant C1, C2, and C1C2 domain constructs and performed mutagenesis of several charged residues proximal to the putative membrane binding region of each C domain. Binding measurements between phosphatidylserine (PS)-containing lipid membrane surfaces and fVIII C domains demonstrated an ionic strength dependence on membrane binding affinity. Mutations to basic residues adjacent to the surface-exposed hydrophobic regions of C1 and C2 differentially disrupted membrane binding, with abrogation of binding occurring for mutations to conserved arginine residues in the C1 (R2163) and C2 (R2320) domains. Lastly, we determined the X-ray crystal structure of the porcine fVIII C2 domain bound to o-phospho-L-serine, the polar headgroup of PS, which binds to a basic cleft and makes charge-charge contact with R2320. We conclude that basic clefts in the fVIII C domains bind to PS-containing membranes through conserved arginine residues via a C domain modularity, where each C domain possesses modest electrostatic-dependent affinity and tandem C domains are required for high affinity binding.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Locking out water at 100°C

We report that thermophilic proteins, present in organisms that live at high temperatures, denature at much higher temperatures compared with their mesophilic counterparts. How these proteins stand the heat has long been researched and is particularly interesting because homologous pairs of thermophilic and mesophilic proteins show a high degree of structural and sequence similarity. In early studies of thermophilic proteins, the proportion of solvent-accessible charged residues was found to be increased at the expense of polar residues. Further analyses confirmed this and also noted strengthening of hydrophobic cores by branched apolar residues. At the same time, whether thermophilic proteins actually need to be more or less flexible than their mesophilic counterparts and the potential usefulness of surface loop deletion has been debated.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Transfer hydrogenation of heavy hydrocarbons with hydrogen-donor solvents

Processes for treating highly viscous hydrocarbons, such as bitumen from oil sands or petroleum residues, with hydrogen-donor solvents are described. The hydrogen-donor solvent is prepared. A mixture of the hydrocarbon and the hydrogen-donor solvent is heated, and the product is cooled to produce a low viscosity and mildly upgraded hydrocarbon. The hydrogen-donor solvent can be modified to improve its solvent usefulness.

Chauhan, Satya P.↗
DOE OSTI2021

Chemical Recycling of Mixed Plastics in Electronic Waste Using Solvent-Based Processing

Currently, less than 20% of electronic waste (E-waste) produced in the U.S. is recycled. To improve the recycling rate of E-waste, the study aimed to: (1) identify the major plastics found within electronic shredder residue (ESR), (2) design solvents and processing conditions capable of separating out 90% of the plastic in ESR, and (3) estimate the energy efficiency of the solvent-based process developed. Preliminary screening showed 25 wt.% of the ESR was composed of plastics, with two polymers dominating the sorted plastic fraction—polystyrene (PS, 40 wt.%) and acrylonitrile butadiene styrene (ABS, 25 wt.%). Subsequently, solvents and anti-solvents were screened using Hansen Solubility Parameter Theory for PS, ABS, and ESR dissolution. The pre-screening results showed dichloromethane (DCM) and tetrahydrofuran (THF) as the most effective solvents for PS and ABS, with methanol (MeOH) and ethylene glycol (EG) as the most effective anti-solvents. By optimizing the dissolution time and the solvents used, the highest polymer dissolution yield (99 wt.%) was achieved using DCM for 48 h. Both MeOH and EG precipitated 71 wt.% of the polymer fraction of ESR. EG removed more phosphorus containing flame retardants (94 wt.%) than MeOH (69 wt.%). Energy analysis indicated that the solvent-based processes could save 25–60% of the embodied energy for PS and ABS. Characterization showed that the solvent-based processing could preserve the high molecular weight fraction of the polymers while removing flame retardants at the same time. The results from this study prove the potential of solvent-based processing to produce secondary plastic materials from E-waste for cross-industry reuse.

Anderson, Lester↗
DOE OSTI2024

Anode Upcycling via Tailored Solvent Treatment

To achieve a truly closed-loop direct recycling process for lithium-ion batteries, all component materials must be recovered. To date, direct recycling method development has primarily focused on the high-value transition-metal cathode materials, while the inherently lower-value graphite has been challenging to recover in a cost-effective manner. However, end-of-life graphite contains a unique engineered value due to the presence of the solid electrolyte interphase (SEI). Growth of the SEI during the cell's active lifetime stabilizes the electronically reactive graphite surface through an irreversible consumption of Li, and thus necessitates both excess lithiation of the cathode and a costly and time-intensive formation procedure during manufacturing. An optimized pre-formed SEI that capitalizes on existing SEI components from end-of-life batteries has the potential to significantly reduce cathode lithiation requirements and eliminate the critical bottleneck of formation cycling during cell remanufacturing. Further, retaining Li at the anode obviates the need for a separate Li leaching and recovery step, improving the overall efficiency of the direct recycling line. In this work, we present a novel approach to "upcycling" spent graphite through use of tailored chemical treatment to remove adverse (i.e., highly resistive and/or poorly passivating) SEI species while retaining beneficially passivating components. We have explored a rational set of solvents spanning a range of polarity, proticity, and molecular size to evaluate structure-property-performance relationships between applied solvent(s), removed and remaining SEI species, and electrochemical response of the resulting graphite product. Further, we have developed and optimized a robust and holistic analysis procedure that couples symmetric-cell electrochemical testing, multi-modal materials characterization, and advanced electrochemical modeling. These analysis results inform a set of correlative metrics for graphite performance relative to both solvent properties and upcycled SEI composition. We demonstrate effective tunability in the residual SEI composition by varying solvent identity and concentration, and report on several promising solvent systems that achieve comparable or performance to pristine graphite.

anode recycling↗
DOE OSTI2022

Carbon Electrodes from Powder River Basin Coal Development of Competitive Supercapacitor Electrodes of Diverse Compositions from Coal Extract

Recent demand for coal as a thermal energy source has decreased significantly and will likely continue to decrease as renewable sources of energy become more available and environmental concern and cost from burning coal makes it more costly than renewables. Given that Powder River Basin (PRB) coal in Wyoming has relatively low thermal energy, it is critical for Wyoming to employ coal in other capacities at the current energy transition period in history. Among many potential non-thermal applications, PRB coal can be utilized for membrane and electrode applications through the formation of carbon fibers. Coal-derived membranes can become low-cost, conductive membranes for use in electrodialysis separation processes. Carbon fiber derived electrodes have been shown be a cost-effective alternative to typical electrode materials that can meet or exceed the performance of current carbon electrode materials. In this talk, we demonstrate the manufacture of supercapacitor electrodes from Powder River Basin (PRB) coal-derived precursors. Specifically, PRB coal was treated in cheap solvents, partitioned into liquid extract and solid residue. An electropinning process has been developed that can convert either the liquid extract or the solid residue into carbon fiber mats. The electrospinning process is versatile with many tunable process parameters to achieve desirable physiochemical properties. For example, the coal residue can be manipulated by additional heat treatment, or by adding binders, salts, or surfactants to create a solution that can be electrospun into advanced carbon electrodes with desirable structural and surface properties. Similarly, some of the liquid extract (tar fraction) can be subsequently reacted with toluene diisocyanate to create resinous coal-derived polyurethane (PUs) as a spinnable ink. Carbon nanofiber mats made from our proprietary electrospinning process were further carbonized at temperature ranging from 700°C to 900°C before they are used as electrodes in supercapacitors. Galvanostatic charge-discharge (GCD) results show that the best performing PU fiber mats can deliver a specific capacitance of 604 F g -1 at the current density of 1 A g -1 . A carbon fiber mat from a different solvent extraction residue also delivered the specific capacitance of 508 F g -1 . These specific capacitance values are comparable to or better than commercial activated carbons, demonstrating the viability of manufacturing carbon nanofiber electrodes from coal without the use of a commercial polymer as binder in the spinning ink.

Cincotta, Robert↗