Search NASA⌕ Search

SEARCH · Search NASA

Results for “ring resonator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Generation of nanosecond THz pulses using a high gain ring resonator with a semiconductor switch

A 250 GHz quasi-optical ring resonator consisting of an input coupler and three mirrors has been designed and tested. A low-loss silicon wafer in the ring provides output coupling of the stored power when irradiated by a pulse from a 532 nm laser. The ring created 5.8 ns, 268 mW output power pulses when excited by a 17 mW, 250 GHz continuously operating input source, achieving a power gain of 16. In a fully tuned ring, higher gain is achievable. If the ring was used with a pulsed input source having a pulse length of several times the fill time, the ring could be used as an efficient pulse compressor with similar high gain. The resonator has a wide range of applications, including, at low power, spectroscopy and, at high power, testing of accelerator structures and materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2016

Ring Resonator for Detection of Melting Brine Under Shallow Subsurface of Mars

Laboratory experimental evidence using Raman spectroscopy has shown that liquid brine may form below the shallow subsurface of Mars. A simpler experimental method to verify the presence of liquid brine or liquid water below Mars surface is needed. In this paper, a ring resonator is used to detect the phase change between frozen water and liquid water below a sandy soil that simulates the Mars surface. Experimental data shows that the ring resonator can detect the melting of thin layers of frozen brine or water up to 15 mm below the surface.

brine↗
NASA NTRS2016

Ring Resonator for Detection of Melting Brine Under Shallow Subsurface of Mars

Laboratory experimental evidence using Raman spectroscopy has shown that liquid brine may form below the shallow subsurface of Mars. A simpler experimental method to verify the presence of liquid brine or liquid water below Mars surface is needed. In this paper, a ring resonator is used to detect the phase change between frozen water and liquid water below a sandy soil that simulates the Mars surface. Experimental data shows that the ring resonator can detect the melting of thin layers of frozen brine or water up to 15 mm below the surface.

Mars↗
NASA NTRS2010

Differential Resonant Ring YIG Tuned Oscillator

A differential SiGe oscillator circuit uses a resonant ring-oscillator topology in order to electronically tune the oscillator over multi-octave bandwidths. The oscillator s tuning is extremely linear, because the oscillator s frequency depends on the magnetic tuning of a YIG sphere, whose resonant frequency is equal to a fundamental constant times the DC magnetic field. This extremely simple circuit topology uses two coupling loops connecting a differential pair of SiGe bipolar transistors into a feedback configuration using a YIG tuned filter creating a closed-loop ring oscillator. SiGe device technology is used for this oscillator in order to keep the transistor s 1/f noise to an absolute minimum in order to achieve minimum RF phase noise. The single-end resonant ring oscillator currently has an advantage in fewer parts, but when the oscillation frequency is greater than 16 GHz, the package s parasitic behavior couples energy to the sphere and causes holes and poor phase noise performance. This is because the coupling to the YIG is extremely low, so that the oscillator operates at near the unloaded Q. With the differential resonant ring oscillator, the oscillation currents are just in the YIG coupling mechanisms. The phase noise is even better, and the physical size can be reduced to permit monolithic microwave integrated circuit oscillators. This invention is a YIG tuned oscillator circuit making use of a differential topology to simultaneously achieve an extremely broadband electronic tuning range and ultra-low phase noise. As a natural result of its differential circuit topology, all reactive elements, such as tuning stubs, which limit tuning bandwidth by contributing excessive open loop phase shift, have been eliminated. The differential oscillator s open-loop phase shift is associated with completely non-dispersive circuit elements such as the physical angle of the coupling loops, a differential loop crossover, and the high-frequency phase shift of the n-p-n transistors. At the input of the oscillator s feedback loop is a pair of differentially connected n-p-n SiGe transistors that provides extremely high gain, and because they are bulk-effect devices, extremely low 1/f noise (leading to ultralow RF phase noise). The 1/f corner frequency for n-p-n SiGe transistors is approximately 500 Hz. The RF energy from the transistor s collector output is connected directly to the top-coupling loop (the excitation loop) of a single-sphere YIG tuned filter. A uniform magnetic field to bias the YIG must be at a right angle to any vector associated with an RF current in a coupling loop in order for the precession to interact with the RF currents.

Parrott, Ronald A.↗
NASA NTRS1983

Folded Fabry-Perot quasi-optical ring resonator diplexer Theory and experiment

Performance of folded Fabry-Perot quasi-optical ring resonator diplexers with different geometries of reflecting surfaces is investigated both theoretically and experimentally. Design of optimum surface geometry for minimum diffraction, together with the figure of merit indicating improvement in performance, are given.

Pickett, H. M.↗
DOE OSTI2023

System and method for sub-wavelength detection for jetting-based additive manufacturing using a split ring resonator probe

The present disclosure relates to a system for detecting and analyzing droplets of feedstock material being ejected from an additive manufacturing device. The system makes use of a split ring resonator (SRR) probe including a ring element having a gap, with the gap being positioned adjacent a path of travel of the droplets of feedstock material. An excitation signal source is used for supplying an excitation signal to the SRR probe. An analyzer analyzes signals generated by the SRR probe in response to perturbations in an electric field generated by the SRR probe as the droplets of feedstock material pass the ring element. The signals are indicative of dimensions of the droplets of feedstock material.

Mukherjee, Saptarshi↗
DOE OSTI2024

Spatially resolved measurements of electron density of a magnetically confined split-ring resonator source

Laser-collisional induced fluorescence is used to study the plasma generated by a split-ring resonator discharge under an external cusp shaped magnetic field created by permanent magnets. The electron density and electron temperature are measured for a helium plasma at different pressures, powers, and magnet field strengths. It is found that the magnetic fields produce higher electron temperatures with peak temperatures of ∼3 eV, while the no magnet case has peak temperatures of ∼0.8 eV. Conversely, the peak electron density is obtained in the no magnet case at a value of ∼1.9 × 1011 cm−3. This indicates that the cusp-field did magnetize the electrons, but contrary to expectations, it resulted in a decrease in electron density. This is believed to be due to the magnetic field having negative effects on the resonance of the plasma source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Photorefraction-induced Bragg scattering in cryogenic lithium niobate ring resonators

We report intracavity Bragg scattering induced by the photorefractive (PR) effect in high-Q lithium niobate ring resonators at cryogenic temperatures. We show that when a cavity mode is strongly excited, the PR effect imprints a long-lived periodic space-charge field. This residual field in turn creates a refractive index modulation pattern that dramatically enhances the back scattering of an incoming probe light, and results in selective and reconfigurable mode splittings. This PR-induced Bragg scattering effect, despite being undesired for many applications, could be utilized to enable optically programmable photonic components.

42 ENGINEERING↗
NASA NTRS1996

Mode Orientation Control For Sapphire Dielectric Ring Resonator

Small sapphire tuning wedge used in technique for solving mode-purity problem associated with sapphire dielectric-ring resonator part of cryogenic microwave frequency discriminator. Breaks quasi-degeneracy of two modes and allows selective coupling to just one mode. Wedge mounted on axle entering resonator cavity and rotated while resonator cryogenically operating in vacuum. Furthermore, axle moved vertically to tune resonant frequency.

Santiago, David G.↗
NASA NTRS1990

Measurement and analysis of a microwave oscillator stabilized by a sapphire dielectric ring resonator for ultra-low noise

Phase-noise measurements are presented for a microwave oscillator whose frequency is stabilized by a whispering-gallery sapphire ring resonator with Q of 200,000. This mode involves little metallic conduction and allows nearly full use of the very low dielectric loss in sapphire. Several mode families have been identified, in good agreement with frequency calculations. For a 5-cm wheel resonator in a 7.6-cm container, Q values above 100,000 were found at room temperature for all of the modes in this sequence. Coupling Q-values for these same modes ranged from 10,000 (n = 5) to 100,000 (n = 10) for a WR112 waveguide port at the center of the cylinder wall of the containing can. Phase noise measurements for a transistor oscillator locked to the n = 10 (7.84-GHz) mode showed a 1/f cubed dependence for low offset frequencies, and a value of L(f) = -55 dB/Hz at an offset of 10 Hz from the carrier.

Dick, G. John↗
DOE OSTI2021

Structural tuning of nonlinear terahertz metamaterials using broadside coupled split ring resonators

We present an experimental and numerical study of a terahertz metamaterial with a nonlinear response that is controllable via the relative structural arrangement of two stacked split ring resonator arrays. The first array is fabricated on an n-doped GaAs substrate, and the second array is fabricated vertically above the first using a polyimide spacer layer. Due to GaAs carrier dynamics, the on-resonance terahertz transmission at 0.4 THz varies in a nonlinear manner with incident terahertz power. The second resonator layer dampens this nonlinear response. In samples where the two layers are aligned, the resonance disappears, and the total nonlinear modulation of the on-resonance transmission decreases. The nonlinear modulation is restored in samples where an alignment offset is imposed between the two resonator arrays. Structurally tunable metamaterials and metasurfaces can therefore act as a design template for tunable nonlinear THz devices by controlling the coupling of confined electric fields to nonlinear phenomena in a complex material substrate or inclusion.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Optical bistability in self-pumped phase-conjugate ring resonators

Bistable oscillations have been observed in BaTiO3 pumped by a single-mode 30-mW (488-nm) argon-ion laser, which is used simultaneously as a ring passive phase conjugator (RPPC) and as a unidirectional ring resonator (UDRR). Strong oscillations in the UDRR increase the threshold coupling strength required for oscillation in the RPPC. The oscillations in the RPPC reduce the fanning in the crystal necessary for the startup of oscillation in the UDRR. Auxiliary resonators pumped by the RPPC are also bistable with the UDRR. Similar bistable oscillations have been observed when the crystal is used simultaneously as a RPPC and as a linear passive phase conjugator.

Jagannath, H.↗
DOE OSTI2024

Harnessing complexity: Nonlinear optical phenomena in L-shapes, nanocrescents, and split-ring resonators

Here, we conduct systematic studies of the optical characteristics of plasmonic nanoparticles that exhibit C 2v symmetry. In particular, we analyze three distinct geometric configurations: an L-type shape, a crescent, and a split-ring resonator shaped like the Greek letter π. Optical properties are examined using the finite-difference time-domain method. It is demonstrated that all three shapes exhibit two prominent plasmon modes associated with the two axes of symmetry. This is in addition to a wide range of resonances observed at high frequencies corresponding to quadrupole modes and peaks due to sharp corners. Next, to facilitate nonlinear analysis, we employ a semiclassical hydrodynamic model, where the electron pressure term is explicitly accounted for. This model goes beyond the standard Drude description and enables capturing nonlocal and nonlinear effects. Employing this model enables us to rigorously examine the second-order angular resolved nonlinear optical response of these nanoparticles in each of the three configurations. Two pumping regimes are considered, namely, continuous wave (CW) and pulsed excitations. For CW pumping, we explore the properties of the second harmonic generation (SHG). Polarization and angle-resolved SHG spectra are obtained, revealing strong dependence on the nanoparticle geometry and incident wave polarization. The C 2v symmetry is shown to play a key role in determining the polarization states and selection rules of the SHG signal. For pulsed excitations, we discuss the phenomenon of broadband terahertz (THz) generation induced by the difference-frequency generation . It is shown that the THz emission spectra exhibit unique features attributed to the plasmonic resonances and symmetry of the nanoparticles. The polarization of the generated THz waves is also examined, revealing interesting patterns tied to the nanoparticle geometry. To gain deeper insight, we propose an analytical theory that agrees very well with the numerical experiments. The theory shows that the physical origin of the THz radiation is the mixing of various frequency components of the fundamental pulse by the second-order nonlinear susceptibility. An expression for the far-field THz intensity is derived in terms of the incident pulse parameters and the nonlinear response tensor of the nanoparticle. The results presented in this work offer new insights into the linear and nonlinear optical properties of nanoparticles with C 2v symmetry. The demonstrated strong SHG response and efficient broadband THz generation hold great promise for applications in nonlinear spectroscopy, nanophotonics, and optoelectronics. The proposed theoretical framework also provides a valuable tool for understanding and predicting the nonlinear behavior of other related nanostructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Ten Ghz YBa2Cu3O(7-Delta) Superconducting Ring Resonators on NdGaO3 Substrates

YBa2Cu3O(7-delta) thin films were formed on NdGaO3 substrates by laser ablation. Critical temperatures greater than 89 K and critical current densities exceeding 2 x 10(exp 8) Acm(sub -2) at 77 K were obtained. The microwave performance of films patterned into microstrip ring resonators with gold ground planes was measured. An unloaded quality factor six times larger than that of a gold resonator of identical geometry was achieved. The unloaded quality factor decreased below 70 K for both the superconducting and gold resonators due to increasing dielectric losses in the substrate. The temperature dependence of the loss tangent of NdGaO3 was extracted from the measurements.

To, H. Y.↗
NASA NTRS1992

10 GHz YBa2Cu3O7-delta Superconducting Ring Resonators on NdGaO3 Substrates

YBa2Cu3O7-delta thin films were formed on NdGaO3 substrates by laser ablation. Critical temperatures greater than 89 K and critical current densities exceeding 2 x 10(exp.6) A cm(exp.-2) at 77 K were obtained. The microwave performance of films patterned into microstrip ring resonators with gold ground planes was measured. An unloaded quality factor six times larger than a that of a gold resonator of identical geometry was achieved. The unloaded quality factor decreased below 70 K for both the superconducting and gold resonators due to increasing dielectric losses in the substrate. The temperature dependence of the loss tangent of NdGaO3 was extracted from the measurements.

To, H. Y.↗
DOE OSTI2025

Intermodal microwave-to-optical transduction using silicon-on-sapphire optomechanical ring resonator

Optomechanical and electro-optomechanical systems have emerged as one of the most promising approaches for quantum microwave-to-optical transduction to interconnect distributed quantum modalities for scaling the quantum systems. These systems use suspended structures to increase mode overlap and mitigate loss to achieve high efficiency. However, the suspended design’s poor heat dissipation under strong drive limits the ultimate efficiency. Here, we demonstrate an unsuspended optomechanical ring resonator (OMR) based on the silicon-on-sapphire (SOS) platform for microwave-to-optical frequency conversion. The OMR achieves a triply resonant optical-to-optical conversion with an enhanced coupling rateG b = 3.6 gigahertz per square-root milliwatt at a peak conversion efficiency of 1.2% with 3.6-milliwatt microwave drive power and a microwave-to-optical conversion efficiency of 1.5 × 10 −5 at 10-milliwatt optical drive power. Our results show that the unsuspended SOS platform, which mitigates the thermal effect and is compatible with superconducting qubits, is a promising platform for optomechanical circuitry and quantum transduction.

Science & Technology - Other Topics↗