Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotor design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 fps). The stages were tested statically in a 15-in.-dia model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 and 900 fps stages. For the 1050 fps stage, the design-speed forward-radiated power level was about 7 dB higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗
NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 ft/sec). The stages were tested statically in a 15-inch-diameter model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 ft/sec and 900 ft/sec stages. For the 1050 ft/sec stage, the design-speed forward-radiated power level was about 7 db higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗
NASA NTRS2000

Improving Tiltrotor Whirl-Mode Stability with Rotor Design Variations

Further increases in tiltrotor speeds are limited by coupled wing/rotor whirl-mode aeroelastic instability. Increased power, thrust, and rotor efficiency are not enough: the whirl-mode stability boundary must also be improved. With current technology, very stiff, thick wings of limited aspect ratio are essential to meet the stability requirements, which severely limits cruise efficiency and maximum speed. Larger and more efficient tiltrotors will need longer and lighter wings, for which whirl-mode flutter is a serious design issue. Numerous approaches to improving the whirl-mode airspeed boundary have been investigated, including tailored stiffness wings, active stability augmentation, variable geometry rotors, highly swept tips, and at one extreme, folding rotors. The research reported herein began with the much simpler approach of adjusting the chordwise positions of the rotor blade aerodynamic center and center of gravity, effected by offsetting the airfoil quarter chord or structural mass with respect to the elastic axis. The research was recently extended to include variations in blade sweep, control system stiffness, and pitch-flap coupling (delta(sub 3)). As an introduction to the subject, and to establish a baseline against which to measure stability improvements, this report will first summarize results. The paper will then discuss more advanced studies of swept blades and control-system modifications.

Acree, C. W., Jr.↗
NASA NTRS1993

Rotor design optimization using a free wake analysis

The aim of this effort was to develop a comprehensive performance optimization capability for tiltrotor and helicopter blades. The analysis incorporates the validated EHPIC (Evaluation of Hover Performance using Influence Coefficients) model of helicopter rotor aerodynamics within a general linear/quadratic programming algorithm that allows optimization using a variety of objective functions involving the performance. The resulting computer code, EHPIC/HERO (HElicopter Rotor Optimization), improves upon several features of the previous EHPIC performance model and allows optimization utilizing a wide spectrum of design variables, including twist, chord, anhedral, and sweep. The new analysis supports optimization of a variety of objective functions, including weighted measures of rotor thrust, power, and propulsive efficiency. The fundamental strength of the approach is that an efficient search for improved versions of the baseline design can be carried out while retaining the demonstrated accuracy inherent in the EHPIC free wake/vortex lattice performance analysis. Sample problems are described that demonstrate the success of this approach for several representative rotor configurations in hover and axial flight. Features that were introduced to convert earlier demonstration versions of this analysis into a generally applicable tool for researchers and designers is also discussed.

Quackenbush, Todd R.↗
NASA NTRS1978

Foil bearings for axial and radial support of high speed rotors: Design, development, and determination of operating characteristics

Flexible surface thrust and journal foil bearings were fabricated, and their performance was demonstrated, both individually and jointly as a unified rotor support system. Experimental results are documented with graphs and oscilloscopic data of trajectories, waveforms, and scans of amplitude response. At speeds of 40,000 to 45,000 rpm and a mean clearance of the order of 15 to 20 micrometers (600 to 800 micrometers, the resilient, air lubricated, spiral groove thrust bearings support a load of 127 N (29 lb; 13 kgf), equivalent to 3.0 N/sq cm (4.5 lb/sq in 0.31 kgf sq cm). Journal bearings with polygonal sections provided stable and highly damped supports at speeds up to 50,000 rpm.

Licht, L.↗
NASA NTRS1977

Design of rotors for improved structural life

Major rotor design criteria are discussed with particular emphasis on those aspects of rotor design that ensure long life component integrity. Dynamic considerations, that necessitate tuning of bladed disk and seal assemblies to avoid excessive vibratory stress at both design and off-design conditions are reviewed as well as low cycle fatigue considerations, which have resulted in detailed analysis procedures to establish part temperature and stress variation throughout an operating cycle and extensive specimen and component fatigue testing to establish safe cyclic operating limits. The frequency, size, and behavior of intrinsic material defects were investigated. Manufacturing process improvements, including the application of increasingly sophisticated inspection techniques and quality control procedures are reviewed in light of their impact on component durability.

Hill, J. T.↗