Results for “selective laser sintering” — Page 2

NASA NTRS2003

Low Thermal Conductivity Thermal Barrier Coatings Developed

Thermal barrier coatings (TBCs) are used extensively in modern gas turbine engines to thermally insulate air-cooled metallic components from the hot gases in the engine. These coatings typically consist of a zirconia-yttria ceramic that has been applied by either plasma spraying or physical vapor deposition. Future engines will rely even more heavily on TBCs and will require materials that have even higher temperature capability with improved insulation (i.e., lower thermal conductivity even after many hours at high temperature). This report discusses new TBCs that have been developed with these future requirements in mind. The Ultra-Efficient Engine Technology Program at the NASA Glenn Research Center is funding this effort, which has been conducted primarily at Glenn with contractor support (GE and Howmet) for physical vapor deposition. As stated, the new TBC not only had to be more insulating but the insulation had to persist even after many hours of exposure-that is, the new TBC had to have both lower conductivity and improved sintering resistance. A new type of test rig was developed for this task. This new test approach used a laser to deliver a known high heat flux in an essentially uniform pattern to the surface of the coating, thereby establishing a realistic thermal gradient across its thickness. This gradient was determined from surface and backside pyrometry; and since the heat flux and coating thickness are known, this permitted continuous monitoring of thermal conductivity. Thus, this laser rig allowed very efficient screening of candidate low-conductivity, sinter-resistant TBCs. The coating-design approach selected for these new low-conductivity TBCs was to identify oxide dopants that had the potential to promote the formation of relatively large and stable groupings of defects known as defect clusters. This approach was used because it was felt that such clusters would reduce conductivity while enhancing stability. The approach proved to be successful: low-conductivity TBCs having improved sintering resistance were developed.

Zhu, Dongming↗

NASA NTRS2019

Optimization of Aluminum-Tin Ink Composition and Sintering in Atmospheric Conditions

This study will focus on the basics of generating an aluminum-tin ink that can sinter in air and exhibits properties near that of a solid aluminum-tin alloy. Sintering temperatures will also be assessed in this study. Once the optimal aluminum ink composition is determined, the optimal ink thickness for homogeneous sintering must be determined by additional experimentation. Additive manufacturing is a rapidly developing and growing manufacturing process and has proven successful in many different ways. Processes, such as extrusion three-dimensional (3D) printing and selective laser melting (SLM), have proven to work but have limitations, such as material capabilities or density issues. SLM is a revolutionary process for additive manufacturing of metals but cannot be used in outer space due to the need for metallic powder which would diffuse into the atmosphere in a zero-gravity environment. For this reason, metallic ink additive manufacturing is a potential solution. Work is being done on metallic ink additive manufacturing in a vacuum for electrical applications. This project has focused on developing an aluminum-tin metallic ink that can sinter without the need of a vacuum or inert gas-purged atmosphere in order to prevent oxidation of the aluminum by adding flux. Once a potential ink composition has been determined through sintering of small disks and thin layers of ink, the ink may be studied with a multimaterial 3D printer at NASA Marshall Space Flight Center (MSFC) in future experiments. If successful, this aluminum-tin ink will be capable for use on the International Space Station to make replacement parts quickly. Along with its zero-gravity advantages, this ink may also have applications on Earth because it may be extruded on a substrate with precise ceramic tips in a 3D printing process. This would allow the fabrication of precise, complex shapes and may generate a much faster and more efficient printing process as compared with traditional powder bed additive manufacturing processes. The process would not be limited by a small building volume because the system would not require an enclosed chamber.

Courtright, Z. S.↗

NASA NTRS2018

Hybrid Additive Manufacturing Deposition and Selective Laser Melting Techniques Applied to Copper-Alloy Liquid Rocket Engine Combustion Chambers

Virgin Orbit and the NASA Marshall Space Flight Center have partnered to fabricate a small, multi-metallic, regeneratively cooled thrust chamber by leveraging the strengths of two different types of additive manufacturing: Direct Metal Laser Sintering (DMLS) for the copper alloy liner and blown powder Directed Energy Deposition (DED) for the Inconel structural jacket. The DED is being developed using Virgin Orbit's DMG Mori Seiki hybrid additive/subtractive machining center to further enable unique processing and further cost savings. The materials chosen are preferred for high performance thrust chamber applications, representing a significant advancement from the compromises typically made in the production of metal 3D printed thrust chambers for rocket engines. The 1.2K-lbf thrust article is a 16" tall, 3" diameter design modified for this effort to be regeneratively cooled with water and hot fired using a RP-1/LOX pintle-style development injector from Virgin Orbit's NewtonFour upper stage engine. The thrust chamber was tested at Virgin Orbit's Necker test site in Mojave, California. Results from this test campaign are reported in addition to information characterizing the liner, jacket, and bimetallic diffusion layer materials. This paper will also highlight some of the future bimetallic thrust chamber developments that MSFC and Virgin Orbit will complete under a recently awarded NASA contract.

Zagorski, Kevin↗

NASA NTRS2015

Selective Laser Melting Inconel 718 Restart Study

Selective Laser Melting (SLM) machines can occasionally shut down (such as in the event of a power failure), which requires the SLM build to be restarted. It has been observed that machine restarts can produce visible "restart lines" in the part, and, in at least one instance, a test specimen containing a restart line exhibited poor mechanical properties. The goal of this study is to evaluate the effect of different machine restart factors on the mechanical properties of the produced SLM material. Test specimens were produced by varying time to restart, the number of re-sinters, and whether or not the build required re-levelling. These are build variables that are typically controlled by the machine operator. Test results indicate that re-leveling and using three re-sinters produces acceptable material. Statistical analysis indicates that re-leveling and re-sintering have strong effects on the resulting material properties. Additionally, the visibility of a restart line loosely correlates with material properties such that obvious restart lines tended to indicate worse material properties.

Tilson, William G.↗

NASA NTRS2021

Post-Landing Major Element Quantification Using SuperCam Laser Induced Breakdown Spectroscopy

The SuperCam instrument on the PerseveranceMars 2020 rover uses a pulsed 1064 nm laser to ablate targets at a distance and conduct laser induced breakdown spectroscopy (LIBS) by analyzing the light from the resulting plasma. SuperCam LIBS spectra are preprocessed to remove ambient light, noise, and the continuum signal present in LIBS observations. Prior to quantification, spectra are masked to remove noisier spectrometer regions andspectra are normalized to minimize signal fluctuations and effectsof target distance.In some cases, the spectra are also standardized or binned prior to quantification. To determine quantitative elemental compositionsof diverse geologic materials at Jezero crater, Mars, we use a suite of 1198 laboratory spectra of 334 well-characterized reference samples. The samples were selected to span a wide range of compositions and include typical silicate rocks, pure minerals (e.g.,silicates, sulfates, carbonates, oxides),more unusual compositions (e.g.,Mn oreand sodalite), andreplicates of the sintered SuperCam calibration targets (SCCTs) onboardthe rover. For each major element (SiO2, TiO2, Al2O3, FeOT, MgO, CaO, Na2O, K2O), the database was subdivided into five“folds” with similar distributions of the element of interest. One fold was held out as an independent test set, and the remaining fourfolds were used to optimize multivariate regression models relating the spectrum to the composition. We considered a variety of models, and selected several for further investigation for each element, based primarily on the root mean squared error of prediction (RMSEP) on the test set, when analyzed at 3m. In cases with several models of comparable performance at 3 m, we incorporated the SCCT performance at different distances to choose the preferred model. Shortly after landing on Mars and collecting initial spectra of geologic targets, we selected one model per element. Subsequently, with additional data from geologic targets, some models were revised to ensure results that are more consistent with geochemical constraints. The calibration discussed here is a snapshot of an ongoing effort to deliver the most accurate chemical compositions with SuperCam LIBS.

Mars 2020↗

NASA NTRS2003

Creep Resistance of ZrO2 Ceramic Improved by the Addition of a Small Amount of Er2O3

Zirconia (ZrO2) has great technological importance in structural, electrical, and chemical applications. It is the crucial component for state-of-the art thermal barrier coatings and an enabling component as a solid electrolyte for solid-oxide fuel cell systems. Pure ZrO2 is of limited use for industrial applications because of the phase transformations that occur. Upon the addition of stabilizers, cubic (c-ZrO2) and tetragonal (t-ZrO2) forms can be preserved. It is the stabilized and partially stabilized forms of zirconia that function as thermal barrier coatings, solid electrolytes, and oxygen sensors and that have numerous applications in the electrochemical industry. The cubic form of ZrO2 is typically stabilized through Y2O3 additions. However, Y2O3-stabilized zirconia is susceptible to deformation at high temperatures (greater than 900 C) because of the large number of slip systems and the high oxygen diffusion rates, which result in high creep rates at high temperatures. Successful use of ZrO2 at high temperatures requires that new dopant additives be found that will retain or enhance the desirable properties of cubic ZrO2 and yet produce a material with lower creep rates. At the NASA Glenn Research Center, erbium oxide (Er2O3) was identified as a promising dopant for improving the creep resistance of. ZrO2. The selection of Er2O3 was based on the strong interactions of point defects and dislocations. Single crystals of 5 mol% Er2O3- doped ZrO2 rods (4 mm in diameter) and monofilaments (200 to 300 mm in diameter and 30 cm long) were grown using the laser-heated float zone technique, and their creep behavior was measured as a function of temperature. The addition of 5 mol% Er2O3 to single-crystal ZrO2 improved its creep resistance at high temperatures by 2 to 3 orders of magnitude over state-of-the-art Y2O3-doped crystals. Detailed microstructural characterization of ZrO2-Er2O3 single crystals has identified new mechanisms for improving the creep resistance of this class of materials. Adding Er2O3 to ZrO2 results in microstructure of stable and metastable tetragonal precipitates that with thermal treatment evolve to a tweed structure of nanosize tetragonal lamellae. The superior high-temperature creep resistance of Er2O3-doped ZrO2 is attributed to nanoscale precipitation hardening. Doping with Er2O3 will significantly increase the upper-use temperature limit of ZrO2. Potential applications include using Er2O3-doped ZrO2 as a high-temperature fiber for structural applications and adding Er2O3 to reduce the sintering rates of ZrO2 thermal barrier coatings. This work was conducted at Dpto. de F sica de la Materia Condensada, Universidad de Sevilla, Spain, and at NASA Glenn.

Martinez-Fernandez, Julian↗

NASA NTRS2017

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Aquirre, Fernando↗

NASA NTRS2016

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Schatzel, Donald↗