Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape memory composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Shape memory behavior and recovery force of 4D printed textile functional composites

Four-dimensional (4D) printing of multi-directionally reinforced preforms has tremendous potential for the development of next generation functional composites by using the capabilities of 3D printing technology, 3D textile preform design, and polymer shape memory behavior. This paper demonstrates the shape memory behavior and recovery force of 4D printed circular braided tube preforms and their silicone elastomer matrix composites. The preforms were printed by fused deposition modeling using the shape memory polymer (SMP), polylactic acid (PLA). The effects of braiding angle, tube wall thickness, and shape recovery temperature on the shape memory behavior of 4D printed tube preforms and their silicone elastomer matrix composites have been characterized. Measurements of shape recovery forces of the preform and composite were conducted using dynamic mechanical analysis (DMA). The braided microstructural parameters and shape recovery temperature have a significant effect on the preform shape memory behavior. The introduction of the silicone elastomer matrix greatly enhances the shape recovery force, shape recovery ratio, as well as radial compressive failure load of the 4D printed preform/silicone elastomer matrix composite. Finally, building on these results, a potential application for 4D printed textile functional composites is presented.

42 ENGINEERING↗

High-Speed Composite Microactuator Based on Ti{sub 2}NiCu Alloy with Shape Memory Effect

Samples of microactuators are made of a bimorph composite of Ti{sub 2}NiCu alloy with a thermoelastic martensitic transition and the shape memory effect, and their response rate is investigated. The active layer of the composite actuator is a layer of the rapidly quenched Ti{sub 2}NiCu alloy, pseudoplastically prestretched, and an amorphous layer of the same alloy is used as an elastic layer. Typical sizes of the microactuator are 30 × 2 × 2 μm. The controlled amplitude of the displacement of the microactuator tip is approximately 1 μm. The response rate of the microactuator was investigated by scanning electron microscopy. Activation of the microactuator was achieved by heating when electric pulses were passed through it. Full activation of the microactuator at frequencies up to 1 kHz was demonstrated; partial activation was observed at frequencies up to 8 kHz. The possibility of operating the device in a self-oscillating mode at frequencies of the order of 100 kHz is demonstrated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Shape memory polymer nanocomposites and uses thereof

The invention relates to radiopaque shape memory foam compositions and methods of using the compositions. In certain embodiments, the compositions are used in neurovascular occlusion applications.

36 MATERIALS SCIENCE↗

Effects of composition and crystallographic ordering on the ferromagnetic transition in Ni–Co–Mn–In magnetic shape memory alloys

In the present study, the effects of composition and the level of crystallographic ordering were studied in Ni 45 Co 5 Mn 50-X In X magnetic shape memory alloys with X = 13.55, 13.71 and 13.92, in order to reveal the relationship between the Curie temperature (T C ) of the austenite phase and the degree of L2 1 ordering. Various samples were prepared using secondary heat treatments at different temperatures below the order-disorder transition temperature and for different durations, after solution heat treatment, in order to control the degree of ordering. T C s were determined using calorimetric and magnetometry measurements. The relationship between the T C and the degree of order was used to predict the evolution of the order during selected heat treatments. It was shown that the T C of austenite exhibits a monotonous non-linear dependence on the fraction of the L2 1 phase. This relationship was corroborated via ab initio numerical calculations within a mean field approximation. Dependence of the crystallographic order parameter on temperature and duration of secondary heat treatments showed that ordering kinetics is fast, the total degree of order depends only on the annealing temperature and cooling rate for long enough treatments, and maximum achievable degree of order is limited by the low thermal energy available for atomic diffusion at low temperatures. Lastly, small changes in composition were observed to have a significant impact on martensitic transformation temperatures, and a significant but smaller effect on the ferromagnetic transition in these systems.

36 MATERIALS SCIENCE↗

Neutron diffraction study of the martensitic transformation and chemical order in Heusler alloy Ni 1.91 Mn 1.29 Ga 0.8

In this study, Heusler alloys of Ni-Mn-Ga compositions demonstrate ferromagnetic shape memory effect in the martensitic state. The transformation temperature and the chemical order depend strongly on the composition. In the current work, the structure and chemical order of the martensitic phase of Ni 1.91 Mn 1.29 Ga 0.8 were studied using neutron diffraction; the diffraction pattern was refined using the FullProf software. It was determined that the structural transition occurs around 330 K. At room temperature, 300 K, which is below the martensite transformation temperature, all the Bragg reflections can be described by a monoclinic lattice with a symmetry of space group P 1 2/m 1 and lattice constants of a = 4.23047(7) [Å], b = 5.58333(6) [Å], c = 21.0179(2) [Å], beta = 90.328(1). The chemical order is of critical importance in these alloys, and it was previously studied at 363 K. Analysis of the neutron diffraction in the monoclinic phase shows that the chemical order is maintained during the martensitic transformation.

36 MATERIALS SCIENCE↗

Enhanced superelasticity of nanocrystalline NiTi/NiTiNbFe laminar composite

This study explores a new concept of the synergy between two constituent shape memory alloys (SMAs) in a composite to achieve a wide superelastic temperature window. In this work, a nanocrystalline NiTi/NiTiNbFe dual-SMA composite is designed, in which two constituent SMAs are both capable of stress-induced martensitic transformation, but within different temperature ranges. Based on the principle of lattice strain matching between the two SMAs, superelastic martensitic transformation in one induces superelastic transformation in the other at temperatures the latter will not when standing alone. Furthermore, via this synergy the composite is able to achieve an ultra-wide superelastic temperature window of 336°C, from -196 to 140°C, with a ~5% tensile strain recovery and high superelastic stresses in the range of 700~1400 MPa. Such properties appear superior to all NiTi-based shape memory alloys to date.

36 MATERIALS SCIENCE↗

Fabrication and Properties of Composite Artificial Muscles Based on Nylon and a Shape Memory Alloy

This paper focuses on the design, fabrication and investigation of the mechanical properties of new artificial muscles formed by twisting and annealing. The artificial muscles designed by twisting nylon have become a popular topic in the field of smart materials due to their high mechanical performance with a large deformation and power density. However, the complexity of the heating and cooling system required to control the nylon muscle is a disadvantage, so we have proposed a composite artificial muscle for providing a direct electricity-driven actuation by integrating nylon and a shape memory alloy (SMA). In this paper, the design and fabrication process of these composite artificial muscles are introduced before their mechanical properties, which include the deformation, stiffness, load and response, are investigated. The results show that these composite artificial muscles that integrate nylon and a SMA provide better mechanical properties and yield up to a 44.1% deformation and 3.43 N driving forces. The good performance and direct electro-thermal actuation make these composite muscles ideal for driving robots in a method similar to human muscles.

36 MATERIALS SCIENCE↗

Nanoengineered Shape-Memory Hemostat

Uncontrolled hemorrhage is the predominant cause of preventable combat deaths. Various biomaterials serve as hemostatic agents due to their procoagulant or absorptive activity. However, these biomaterials often lack expansion capabilities, which severely limits use in noncompressible wounds. This study combines a hemostatic nanocomposite with a shape-memory polymer foam to design a composite material with both hemostatic and physical expansion properties. This composite is fabricated in two formulations: a foam externally coated in a highly concentrated nanocomposite (“coated composite”) and a foam containing a diluted nanocomposite infused throughout its pores (“infused composite”). Both formulations retain the shape-memory foam's expansion property. Further, the coated composite shows improved fluid uptake (>2-fold) versus infused composites or foam. The nanocomposite component dissociates from the foam under degradative conditions, with the foam remaining stable for 30 days. Hemostatic studies illustrate that the coated composite reduces the clotting time by ≈20%. Alternatively, the infused composite improves clotting over a larger distance (up to ≈2× distance from the composite). These results signify a modular hemostatic ability: the coated composite reduces clotting and improves fluid uptake, while the infused composite achieves diffuse clotting and maintains mechanical properties. Thus, these materials pose a strong potential for use in noncompressible wounds.

60 APPLIED LIFE SCIENCES↗

Ab initio study of the composite phase diagram of Ni–Mn–Ga shape memory alloys

The magnetic and structural properties of a series of nonstoichiometric Ni–Mn–Ga Heusler alloys are theoretically investigated in terms of the density functional theory. Nonstoichiometry is formed in the coherent potential approximation. Concentration dependences of the equilibrium lattice parameter, the bulk modulus, and the total magnetic moment are obtained and projected onto the ternary phase diagram of the alloys. The stable crystalline structures and the magnetic configurations of the austenitic phase are determined.

36 MATERIALS SCIENCE↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

36 MATERIALS SCIENCE↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

Wilson, Thomas S.↗

Post polymerization cure shape memory polymers

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

Wilson, Thomas S.↗

Shape-morphing composites with designed micro-architectures

Shape memory polymers (SMPs) are attractive materials due to their unique mechanical properties, including high deformation capacity and shape recovery. SMPs are easier to process, lightweight, and inexpensive compared to their metallic counterparts, shape memory alloys. However, SMPs are limited to relatively small form factors due to their low recovery stresses. Lightweight, micro-architected composite SMPs may overcome these size limitations and offer the ability to combine functional properties (e.g., electrical conductivity) with shape memory behavior. Fabrication of 3D SMP thermoset structures via traditional manufacturing methods is challenging, especially for designs that are composed of multiple materials within porous microarchitectures designed for specific shape change strategies, e.g. sequential shape recovery. We report thermoset SMP composite inks containing some materials from renewable resources that can be 3D printed into complex, multi-material architectures that exhibit programmable shape changes with temperature and time. Through addition of fiber-based fillers, we demonstrate printing of electrically conductive SMPs where multiple shape states may induce functional changes in a device and that shape changes can be actuated via heating of printed composites. As a result, the ability of SMPs to recover their original shapes will be advantageous for a broad range of applications, including medical, aerospace, and robotic devices.

36 MATERIALS SCIENCE↗

A novel multifunctional NiTi/Ag hierarchical composite

Creating multifunctional materials is an eternal goal of mankind. As the properties of monolithic materials are necessary limited, one route to extending them is to create a composite by combining contrasting materials. The potential of this approach is neatly illustrated by the formation of nature materials where contrasting components are combined in sophisticated hierarchical designs. In this study, inspired by the hierarchical structure of the tendon, we fabricated a novel composite by subtly combining two contrasting components: NiTi shape-memory alloy and Ag. The composite exhibits simultaneously exceptional mechanical properties of high strength, good super-elasticity and high mechanical damping, and remarkable functional properties of high electric conductivity, high visibility under fluoroscopy and excellent thermal-driven ability. All of these result from the effective-synergy between the NiTi and Ag components, and place the composite in a unique position in the properties chart of all known structural-functional materials providing new opportunities for innovative electrical, mechanical and biomedical applications. Furthermore, this work may open new avenues for designing and fabricating advanced multifunctional materials by subtly combining contrasting multi-components.

ELECTRONIC DEVICES↗