Search NASA⌕ Search

SEARCH · Search NASA

Results for “shear band”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Shock-induced melting and shear banding in single-crystal NaCl

Radiative color temperatures were measured in single-crystal sodium chloride under shock compression parallel to 100-line orientation over a pressure range from 20 to 35 GPa. Color temperatures from 2500 to 4500 K and emittances from 0.003 to 0.3 were determined by fitting observed spectra (450-850 nm) to the Planck greybody radiation law. These data support a heterogeneous shock deformation model of shocked halite in this pressure range. A 2500-K temperature rise, of unknown origin, is observed over the B1-B2 mixed phase region from 25 to 30 GPa. Assuming that shock deformation occurs via yielding in localized planar zones which become melt and the melting temperature at high pressure controls the temperature, it is inferred that the temperature of the B2 fusion curve from 30 to 35 GPa rises from 3200 to 3300 K. The B1-B2-liquid triple point is predicted to be at a temperature of 2250 K and 23.5 GPa.

Schmitt, Douglas R.↗
NASA NTRS1992

Mechanisms of compressive failure in woven composites and stitched laminates

Stitched laminates and angle interlock woven composites have been studied in uniaxial, in-plane, monotonic compression. Failure mechanisms have been found to depend strongly on both the reinforcement architecture and the degree of constraint imposed by the loading grips. Stitched laminates show higher compressive strength, but are brittle, possessing no load bearing capacity beyond the strain for peak load. Post-mortem inspection shows a localized shear band of buckled and broken fibers, which is evidently the product of an unstably propagating kink band. Similar shear bands are found in the woven composites if the constraint of lateral displacements is weak; but, under strong constraint, damage is not localized but distributed throughout the gauge section. While the woven composites tested are weaker than the stitched laminates, they continue to bear significant loads to compressive strains of approx. 15 percent, even when most damage is confined to a shear band.

Cox, B. N.↗
DOE OSTI2024

High pressure suppression of plasticity due to an overabundance of shear embryo formation

Abstract High pressure shear band formation is a critical phenomenon in energetic materials due to its influence on both mechanical strength and mechanochemical activation. While shear banding is known to occur in a variety of these materials, the governing dynamics of the mechanisms are not well defined for molecular crystals. We conduct molecular dynamics simulations of shock wave induced shear band formation in the energetic material 1,3,5-trinitroperhydro-1,3,5-triazine (RDX) to assess shear band nucleation processes. We find, that at high pressures, the initial formation sites for shear bands, “embryos”, form in excess and rapidly lower deviatoric stresses prior to shear band formation and growth. This results in the suppression of plastic deformation. A local cluster analysis is used to quantify and contrast this mechanism with a more typical shear banding seen at lower pressures. These results demonstrate a mechanism that is reversible in nature and that supersedes shear band formation at increased pressures. We anticipate that these results will have a broad impact on the modeling and development of high-strain rate application materials such as those for high explosives and hypersonic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating the compressive strength and strain localization of nanotwinned nickel alloys

Sputter deposited nickel-molybdenum-tungsten (Ni-Mo-W) thin films possess a beneficial suite of properties that stem from the extremely fine growth twins that form during the deposition process. Previously these materi- als were only characterized in tension, however, in this study in situ micropillar compression and post-mortem microstructural analysis of nanotwinned Ni 84 Mo 11 W 5 micropillars were employed to measure the compressive response and elucidate the attendant deformation mechanisms. The pillars exhibit Hookean behavior to com- pressive strengths of 3-3.5 GPa and the onset of non-linear plastic flow was manifest by discrete strain bursts and highly localized shear bands. Plastic deformation was concentrated at the top of the pillar, while the bulk of the micropillar was nominally unaffected. Post-mortem investigations indicate that at sufficiently high stresses shear banding is triggered, resulting in intense and highly localized plastic deformation that led to the formation of twin-free nanocrystalline grains within highly deformed shear bands. By contrast, the regions adjacent to the shear bands were unaffected. The absence of detwinning and dislocation glide mechanisms was unexpected and in direct contrast to what has been observed in nanotwinned Cu-Al. Post-mortem observations of the Ni-Mo-W micropillars suggest that the ultrafine twins create a unique form of dislocation starvation and source-limited plasticity. The ultrahigh compressive strength is governed by the triggering of shear bands rather than the activa- tion of dislocation glide. Finally, the specialized nature of plasticity in nanotwinned Ni-Mo-W is clear, even though the precise trigger for shear band formation in nanotwinned Ni-Mo-W remains to be identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Excellent ballistic impact resistance of Al 0.3 CoCrFeNi multi-principal element alloy with unique bimodal microstructure

Multi-principal element alloys represent a new paradigm in structural alloy design with superior mechanical properties and promising ballistic performance. Here, the mechanical response of Al 0.3 CoCrFeNi alloy, with unique bimodal microstructure, was evaluated at quasistatic, dynamic, and ballistic strain rates. The microstructure after quasistatic deformation was dominated by highly deformed grains. High density of deformation bands was observed at dynamic strain rates but there was no indication of adiabatic shear bands, cracks, or twinning. The ballistic response was evaluated by impacting a 12 mm thick plate with 6.35 mm WC projectiles at velocities ranging from 1066 to 1465 m/s. The deformed microstructure after ballistic impact was dominated by adiabatic shear bands, shear band induced cracks, microbands, and dynamic recrystallization. The superior ballistic response of this alloy compared with similar Al x CoCrFeNi alloys was attributed to its bimodal microstructure, nano-scale L1 2 precipitation, and grain boundary B2 precipitates. Deformation mechanisms at quasistatic and dynamic strain rates were primarily characterized by extensive dislocation slip and low density of stacking faults. Deformation mechanisms at ballistic strain rates were characterized by grain rotation, disordering of the L1 2 phase, and high density of stacking faults.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Influence of gradation on shear behavior and pore water response of sand

Here, this paper examines the influence of particle size distribution (PSD) on the shearing behavior of sand using axisymmetric triaxial compression (ATC) testing in conjunction with 3D imaging using synchrotron micro-computed tomography (SMT). Angular sand was sieved to obtain a narrow gradation (uniform) and a wide gradation (non-uniform) with uniformity coefficients (C u ) of 1.2 and 3.0, respectively. Experiments were conducted under drained conditions and a constant effective cell pressure (σ$^{'}_3$) of 50 kPa at low and high back pressures (BP). Results of paired ATC-SMT were analyzed in terms of global constitutive behavior, strain localization, and localized flow characteristics. A new particle tracking algorithm is developed to expose strain localization. Relative particle translation gradient (RPTG) results revealed that gradation affects how early the shear band develops and a tendency for narrow gradation to exhibit varying degrees of diffused shear band at high axial strain (ε 1 ) even though a clear single shear band was observed at the peak strength. Geometric tortuosity (τ) is used as a quantitative parameter to assess flow changes and the efficiency of the flow path. Representative elementary volumes (REVs) inside and outside the shear band were analyzed and the results showed a variation in flow path characteristics where wide gradation specimens had preferential flow paths.

Computed tomography↗
DOE OSTI2021

Significant disparity of non-basal dislocation activities in hot-rolled highly-textured Mg and Mg-3Al-1Zn alloy under tension

It is well-established that Mg-3Al-1Zn (AZ31) alloy exhibits much better tensile ductility than pure Mg. However, the underlying mechanisms for such difference still remain relatively unexplored at the dislocation level. In this work, we deformed hot-rolled highly-textured pure Mg and AZ31 samples with similar initial microstructures (i.e., grain size and texture) under tension along the rolling direction. Apparent shear banding was only observed in the pure Mg samples from the early stage of the deformation. Shear bands could act as easy paths for crack propagation, leading to low ductility in pure Mg. Apparent shear banding was not noted in deformed AZ31 samples. We then investigated the deformation mechanisms at the dislocation level using transmission electron microscopy. Systematic tilting experiments and statistical analyses of multiple grains at different strain levels revealed a significant disparity of non-basal dislocation activities between pure Mg and AZ31. For pure Mg, dislocations were activated since the early stage of plastic deformation. For AZ31, dislocations were mostly absent at all strain levels, even in the strain-to-failure samples. Non-basal dislocations, including prismatic and pyramidal dislocations, were observed. The promotion of the non-basal dislocation activities and the suppression of dislocations in AZ31 are expected to offer more sustainable hardening, which could elucidate the absence of apparent shear banding and much-improved ductility in AZ31 compared to pure Mg.

Zhao, Dexin↗
DOE OSTI2020

Indirectly probing the structural change in ion-irradiated Zr-Based metallic glasses from small scale mechanical tests

Ion irradiation was applied to tailor the structural heterogeneities in Zr-based metallic glasses at room temperature. Experimental methods of X-ray diffraction, nanoindentation, and micropillar compression were conducted to examine the irradiation effects on their structural and mechanical property changes. It is found that the irradiated materials retained amorphous structure after room-temperature Ni ion irradiation. The reduction of elastic modulus and hardness measured by nanoindentation indicated the irradiation-induced mechanical degradation. A unified statistic model was employed to quantitatively predict the density and strength of irradiation defects, although their specific structural and physical nature is not explicitly included in this model. The transition of non-intersecting shear bands to multiple intersecting shear bands was observed on compression tests of irradiated micropillars with the increase of irradiation dose. Furthermore, the analysis of the displacement excursion of micropillar compression tests indicated a different deformation mode from the unirradiated state. These results from nanoindentation pop-in and micro-pillar compression tests suggested that irradiation eventually leads to a new state with different types and characteristics of structural heterogeneities from violent displacement cascades and non-equilibrium energy deposition/dissipation processes, which also proves ion irradiation as an effective method to tune the structure and mechanical properties of metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Discrepancy in the Critical State Void Ratio of Poorly Graded Sand due to Shear Strain Localization

The critical state (CS) concept is a theoretical framework that models the constitutive behavior of soils, including sand and other granular materials. It supports the notion of a unique postfailure state, where the soil ultimately experiences continuous shearing with no change in the plastic volumetric strain. However, the published literature has frequently noted the nonconvergence of sand specimens with different initial densities to a unique CS in the compression plane due to many factors such as specimen fabric, particle morphology, breakage, and grain size distribution. This paper examines the CS for poorly graded (uniform) glass beads and 3 different types of silica sands using 50 conventional triaxial compression (CTC) experiments, 12 oedometer tests, and in situ synchrotron microcomputed tomography (SMT) scans for 10 CTC experiments. The results of the 50 CTC experiments revealed a diffused CS zone in the compression plane, which was further examined using the in situ SMT scans. A thorough three-dimensional image analysis of the SMT scans accurately quantified the evolution of the local void ratio (elocal) versus axial compression within zones of intensive shearing toward the center of the specimen. The evolution of the void ratio was also measured using the entire volume of the specimen (eglobal). At the CS, the elocal/eglobal ratio was assessed to be ~1.25 when a single shear band developed within the scanned specimens and ~1.1-1.15 for specimens that failed via external bulging that was internally manifested by the development of multiple shear bands. This finding suggests that the CS zone in the compression plane can be attributed to the common wrong consideration of eglobal evolution in lieu of elocal within the developing shear bands. Furthermore, the lack of shear band development in uniaxial compression has made the results of the oedometer test reliable in quantifying the CS parameters in the compression plane.

58 GEOSCIENCES↗
DOE OSTI2020

Parallel three-dimensional simulations of quasi-static elastoplastic solids

Hypo-elastoplasticity is a flexible framework for modeling the mechanics of many hard materials under small elastic deformation and large plastic deformation. Under typical loading rates, most laboratory tests of these materials happen in the quasi-static limit, but there are few existing numerical methods tailor-made for this physical regime. Here, we extend to three dimensions a recent projection method for simulating quasi-static hypo-elastoplastic materials. The method is based on a mathematical correspondence to the incompressible Navier–Stokes equations, where the projection method of Chorin (1968) is an established numerical technique. We develop and utilize a three-dimensional parallel geometric multigrid solver employed to solve a linear system for the quasi-static projection. Our method is tested through simulation of three-dimensional shear band nucleation and growth, a precursor to failure in many materials. As an example system, we employ a physical model of a bulk metallic glass based on the shear transformation zone theory, but the method can be applied to any elastoplasticity model. We consider several examples of three-dimensional shear banding, and examine shear band formation in physically realistic materials with heterogeneous initial conditions under both simple shear deformation and boundary conditions inspired by friction welding.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Assessing continuum plasticity postulates with grain stress and local strain measurements in triaxially compressed sand

Critical state and continuum plasticity theories have been used in research and engineering practice in soil and rock mechanics for decades. These theories rely on postulated relationships between material stresses and strains. Some classical postulates include coaxiality between stress and strain rates, stress–dilatancy relationships, and kinematic assumptions in shear bands. Although numerical and experimental data have quantified the strains and grain kinematics in such experiments, little data quantifying grain stresses are available. Here, we report the first-known grain stress and local strain measurements in triaxial compression tests on synthetic quartz sands using synchrotron X-ray tomography and 3D X-ray diffraction. We use these data to examine the micromechanics of shear banding, with a focus on coaxiality, stress-dilatancy, and kinematics within bands. Our results indicate the following: 1) elevated deviatoric stress, strain, and stress ratios in shear bands throughout experiments; 2) coaxial principal compressive stresses and strains throughout samples; 3) significant contraction along shear bands; 4) vanishing volumetric strain but nonvanishing stress fluctuations throughout samples at all stages of deformation. Our results provide some of the first-known in situ stress and strain measurements able to aid in critically evaluating postulates employed in continuum plasticity and strain localization theories for sands.

42 ENGINEERING↗
DOE OSTI2023

High Pressure Suppression of Plasticity in RDX [Slides]

RDX shear banding nucleates without other defects present and is important for both mechanical properties and for mechano-chemical effects. Above ~1.0 km/s particle velocity, the shear band mechanism ceases to occur. It is not replaced by a phase transformation or other plastic event. Shear band initial sites over-nucleate and lower the VM tress drastically. This results in a fully reversible, high pressure mechanism that suppresses the formation of shear bands.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A numerical and experimental approach to compare the effect of sample thickness in small in-situ SEM and large ex-situ tensile testing in Alloy 709

ASTM standards for tensile tests define specific sample size requirements regardless of grain size of the material. However, sample size requirements for testing should be considered in conjunction with the number of grains within its reduced cross-sectional area. This is particularly important for in-situ Scanning Electron Microscope (SEM) tensile tests, as they have to be conducted on smaller samples. In this study, a comprehensive experimental and numerical evaluation of the effect of specimen thickness (and the resulting number of grains within the cross-section) were conducted using in-situ SEM tensile test (on submillimeter thick samples) and ex-situ tensile tests (on samples of 0.68–5.9 mm thickness) and the results are compared with FEM simulations outcome. All tests were conducted at room temperature and the results are correlated to the number of grains within the thickness of specimens. The tensile test results indicated that even though the 0.2% proof stress and the tensile strength do not vary for the current range of thicknesses (with number of grains in the cross-section varying from 13 to 118), a difference in necking mechanism exists. Post tensile strength, thinner samples undergo more shear failure and diagonal localized necking whereas thicker samples experience more diffuse necking indicated by decreased area of shear failure at the edges and increased area of dimpled tensile failure at the center of the sample. Further, FEM results complement the experimental findings by showing the formation of conjugated localized shear bands on the upper and lower surface in the 0.68 mm thick sample and shear bands combining to form singular shear bands in thicker samples. These results also confirm the validity of the in-situ SEM tensile tests conducted on thinner samples as long as the required minimum number of grains exist within the cross-section.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elucidating the mechanical and thermal response of nanotwinned Ni alloys

Transformative advances in nanoscale materials synthesis, characterization and modeling are enabling the synthesis of materials with unprecedent properties and greater understanding of the nanoscale mechanisms that underpin these properties. Nanotwinned Cu alloys have received considerable attention due to their impressive balance of strength and ductility, but they have limited microstructural stability. Recent instantiation of nanotwins in sputter deposited Ni-Mo-W, and several commercial Ni-based superalloys, point to the potential development of a new class of high temperature materials with a very beneficial suite of mechanical and physical properties. The experimental study described in this report was undertaken to elucidate the nanoscale origins of the thermal and mechanical behavior of nanotwinned Ni alloys. Micropillar compression experiments have shown nanotwinned Ni 85 Mo 15-x W x alloys to possess unusually high strengths above 3.5GPa and enhanced microstructural stability. The strength of these nanotwinned alloys is determined by the abrupt formation of shear bands. This study focused on identifying the nanoscale trigger, or triggers, for shear banding in nanotwinned materials using in situ experiments and atomic-scale postmortem analysis. Contrasting and comparing the mechanical response and postmortem nanostructures of “Mo-rich” and “W-rich” nanotwinned specimens elucidated the importance of the lateral motion of easy glide defects that results in erasure of twins and local coarsening of the nanotwinned microstructure. This twin coarsening was then associated with very localized plasticity, strain softening, and shear band formation. The difference between alloys was further studied by considering the role of various material factors: stacking fault energy, coherent twin boundary spacing and flatness, grain size, and the interactions of solute atoms with twin and grain boundaries. The effect of alloy composition and sputtering power and temperature were also investigated and used to control twin spacing and geometry. Combined with atomic-scale simulations, these experiments insights should allow us to identify strategies for achieving concomitant ultrahigh strength and ductility in nanotwinned Ni alloys. In parallel but synergistic studies, our work was buoyed by collaborative state-of-the-art nanoscale orientation and strain mapping at the DOE National Center for Electron Microscopy (NCEM). For example, novel 4D-STEM techniques were used to acquire nanoscale strain maps. The extremely fine twin spacing limited our measurements of atomic-scale thermal expansion within twins, but recent results from NCEM suggest that it will soon be possible to conduct such measurements and to unravel the origins of the novel thermal expansion characteristics of nanotwinned Ni alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Full-field quantitative visualization of shock-driven pore collapse and failure modes in PMMA

The dynamic collapse of pores under shock loading is thought to be directly related to hot spot generation and material failure, which is critical to the performance of porous energetic and structural materials. However, the shock compression response of porous materials at the local, individual pore scale is not well understood. This study examines, quantitatively, the collapse phenomenon of a single spherical void in PMMA at shock stresses ranging from 0.4 to 1.0 GPa. Using a newly developed internal digital image correlation technique in conjunction with plate impact experiments, full-field quantitative deformation measurements are conducted in the material surrounding the collapsing pore for the first time. The experimental results reveal two failure mode transitions as shock stress is increased: (i) the first in situ evidence of shear localization via adiabatic shear banding and (ii) dynamic fracture initiation at the pore surface. Numerical simulations using thermo-viscoplastic dynamic finite element analysis provide insights into the formation of adiabatic shear bands (ASBs) and stresses at which failure mode transitions occur. Further numerical and theoretical modeling indicates the dynamic fracture to occur along the weakened material inside an adiabatic shear band. Finally, analysis of the evolution of pore asymmetry and models for ASB spacing elucidate the mechanisms for the shear band initiation sites, and elastostatic theory explains the experimentally observed ASB and fracture paths based on the directions of maximum shear.

42 ENGINEERING↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coordinate transformation methodology for simulating quasistatic elastoplastic solids

Molecular dynamics simulations frequently employ periodic boundary conditions where the positions of the periodic images are manipulated in order to apply deformation to the material sample. For example, Lees-Edwards conditions use moving periodic images to apply simple shear. Here, we examine the problem of precisely comparing this type of simulation to continuum solid mechanics. We employ a hypo-elastoplastic mechanical model, and develop a projection method to enforce quasi-static equilibrium. We introduce a simulation framework that uses a fixed Cartesian computational grid on a reference domain, and imposes deformation via a time-dependent coordinate transformation to the physical domain. As a test case for our method, we consider the evolution of shear bands in a bulk metallic glass using the shear transformation zone theory of amorphous plasticity. We examine the growth of shear bands in simple shear and pure shear conditions as a function of the initial preparation of the bulk metallic glass.

74 ATOMIC AND MOLECULAR PHYSICS↗