Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicon”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of Silicon Impurity on the Hydrometallurgical Recovery of NCM622 Cathode

Hydrometallurgy is one of the best approaches to date for recycling LIBs due to its high efficiency, low energy usage, and industrial scalability. However, impurities have always been a thorny issue because they could have unintended impacts on the recovered cathode materials. This research marks the first systematic investigation into the influence of silicon impurity on the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathode obtained from hydrometallurgical recycling. Here we find that silicon nanoparticles will be nucleated at the center of the precursor particles during co-precipitation synthesis, and the silicon core will slowly dissolve in the surrounding ammonia, creating a special hollow structure in the particle. More importantly, the dissolution of silicon impurity will eventually lead to the deposition of silicates in the cathode material, which is an unfavorable result. Test data indicate that NCM622 cathode with 5 at% silicon has a capacity of 148.8 mAh g −1 after 100 cycles at 1/3 C, approximately 10 mAh g −1 lower than the virgin. Despite being relatively mild, the adverse influence of silicon impurity in hydrometallurgical recycling still requires attention.

25 ENERGY STORAGE↗
DOE OSTI2025

3D printable silicone compositions exhibiting high toughness and low durometer

3D printable silicones can be designed with varying crosslink density, network structures, and types of reinforcing additives. Within this design space, one may tailor the uncured material’s rheology and mechanical response to access a wide range of potential applications. However, printable, low modulus silicones, particularly those applicable to direct ink write, are underreported in published literature. To address the need for higher performance, low modulus silicones with demonstrated printability, a new set of ca. 20–50 Shore A hardness silicone elastomers exhibiting ca. 7 MPa ultimate tensile strength and ca. 400–1200% elongation at break is presented. Mechanical properties were analyzed, providing insight to the effects of formulation constituents on mechanical properties. Cyclic mechanical testing of the silicone formulations was also performed, and the energy loss and permanent set throughout cycling were determined. In conclusion, printed structures demonstrate the feasibility of these new silicones as durable frameworks for novel soft device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Non-solvents as physical blowing agents in printable silicone foams

Silicone foams were produced by dispersing an incompatible liquid phase (i.e. a non-solvent) into an uncured, liquid silicone. The formulation and processing parameters were varied to see the effect on porosity and pore morphology. Specifically, two fluorosilanes were added to stabilize the inclusion of fluorinated solvents as blowing agents. As the floruosilane content increased, the void content increased up to about 44 vol. % when the fluorosilane comprised 18 wt. % of the initial formulation. Fumed silica that was treated with a fluorinated silane was also used to try to stabilize the dispersed liquid. While the fumed silica content did not have a strong effect on the total void content, the morphology changed when silica content changed. Various fluorinated solvents with distinct chemical structures were used as the non-solvent and then removed after curing of the silicone. The interaction of the internal non-solvent phase and the silicone phase was expected to influence the porosity. These insights highlight how the manipulation of formulation and processing parameters, focusing on the inclusion of fluorosilanes and fluorinated solvents, contributes to the understanding of how incompatible liquid phases interact with silicone matrices to control porosity and pore morphology. Additionally, these interactions also influenced processability, leading to formulations that could be printed. Higher content of non-solvent inclusions could increase the yield stress and storage modulus of an uncured formulation, leading to the ability to tune intrastrand porosity while a 3D printed architecture could be modified to introduce porosity between the strands. Furthermore, in addition to fluorinated solvents, we also considered non-fluorinated solvents since these may be more industrially relevant in the future. Overall, this approach provides an alternative route to producing porous foams that can be 3D printed, which could be useful for applications like cushioning and protective gear.

physical blowing agent↗
DOE OSTI2025

Entanglement of a nuclear spin qubit register in silicon photonics

Colour centres provide an optical interface to quantum registers based on electron and nuclear spin qubits in solids. The T centre in silicon is an emerging spin–photon interface that combines telecom O-band optical transitions and an electron spin in a scalable photonics platform. Here, in this study, we integrate T centres into single-mode photonic waveguides in a silicon-on-insulator platform. We demonstrate the initialization, coherent control and state read-out of a three-qubit register based on the electron spin of a T centre coupled to a hydrogen and a silicon nuclear spin. The spin register exhibits spin echo coherence times of 0.41(2) ms for the electron spin, 112(12) ms for the hydrogen nuclear spin and 67(7) ms for the silicon nuclear spin. We use nuclear–nuclear two-qubit gates to generate entanglement between the two nuclear spins with a fidelity of F = 0.77(3) and a coherence time of ${T}_{2}^{* }=2.60(8)$ ms. Our results show that a T centre in silicon photonics can realize a multi-qubit register with an optical interface for quantum communication.

Song, Hanbin [Lawrence Berkeley National Laborator↗
DOE OSTI2025

Characterization of the Cherenkov Photon Background for Low-noise Silicon Detectors in Space

Future space observatories that seek to perform imaging and spectroscopy of faint astronomical sources will require ultra-low-noise detectors that are sensitive over a broad wavelength range. Silicon charge-coupled devices (CCDs), such as EMCCDs, skipper CCDs, multi-amplifier sensing CCDs, and single-electron sensitive read out CCDs have demonstrated the ability to detect and measure single photons from X-ray energies to near the silicon band gap (∼1.1 μm), making them candidate technologies for this application. Here, in this context, we study a relatively unexplored source of low-energy background coming from Cherenkov radiation produced by energetic cosmic rays traversing a silicon detector. We present a model for Cherenkov photon production and absorption that is calibrated to laboratory data, and we use this model to characterize the residual background rate for ultra-low-noise silicon detectors in space. We study how the Cherenkov background rate depends on detector thickness, variations in solar activity, and the contribution of heavy cosmic ray species (Z > 2). We find that for thick silicon detectors, such as those required to achieve high quantum efficiency at long wavelengths, the rate of cosmic-ray-induced Cherenkov photon production is comparable to other detector and astrophysical backgrounds. We apply our Cherenkov background model to simulated spectroscopic observations of extra-solar planets, and we find that thick detectors continue to outperform their thinner counterparts at longer wavelengths despite a larger Cherenkov background rate. Furthermore, we find that minimal masking of cosmic-ray tracks continues to maximize the signal-to-noise ratio of very faint sources despite the existence of extended halos of Cherenkov photons.

Astronomical detectors↗
DOE OSTI2025

Silicon wafer fracture stress for tracking sensors in particle physics experiments

For the construction of the ATLAS Inner Tracker strip detector, silicon strip sensor modules are glued directly onto carbon fibre support structures using a soft silicone gel. During tests at temperatures below -35°C, several of the sensors were found to crack due to a mismatch in coefficients of thermal expansion between polyimide circuit boards with copper metal layers (glued onto the sensor) and the silicon sensor itself. While module assembly procedures were developed to minimise variations between modules, cold tests showed a wide range of temperatures at which supposedly comparable modules failed. The observed variance (fracture temperatures between -35°C and -70°C) for supposedly comparable modules suggests an undetected variation between modules suspected to be intrinsic to the silicon wafer itself. Therefore, a test programme was developed to investigate the fracture stress of representative sensor wafer cutoffs. This paper presents results for the fracture stress of silicon sensors used in detector modules.

Detector design and construction technologies and ↗
DOE OSTI2025

Characterization of Performance Degradation Mechanisms in Low-Cost High Throughput DI-O3 Layer for Passivated Contact Silicon Solar Cells

Characterization and mitigating performance limiting defects in Silicon (Si) PV is one of key areas to be addressed to improve PV hardware costs and energy yield in order to lower the levelized cost of energy (LCOE) of installed PV cost to $0.02/kWh. As Si PV cells efficiencies have surpassed 22% and approaching 23%, the recombination at the metal contacts have become the focus point to be addressed. Passivated contact technologies—having a heterojunction with a band-gap larger than silicon between the metal and silicon—have emerged as a great potential for future highand ultrahigh-efficiency solar cells, as it concurrently reduces recombination and increases carrier selectivity, by incorporating thin films within the contact structure. Passivated contact Si solar cell technologies use a wide variety of tunnel layers—playing a crucial role to passivate metal contacts and tunnel charge carriers—including stoichiometric silicon oxide (SiO 2 ) grown by thermal oxidation and Low-Pressure Chemical Vapor Deposition (LPCVD) technique and silicon oxide (SiO x ) by hot nitric acid. However, thorough investigations on understanding the failure and performance degradation mechanisms associated with tunnel layers are still limited to date. Unlocking those degradation characteristics in crucial tunnel layers could improve the reliability and energy yield of passivated contact Si solar cells. Besides, the technique of growing aforementioned tunneling layers are low throughput, and requires high temperature processes and/or a vacuum environment. In this project, we investigated the performance degradation mechanisms of a low-cost high-throughput ozonated oxide (DI-O 3 ) tunnel layer for the passivated contact Si solar cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Prediction of Silicon Content in a Blast Furnace via Machine Learning: A Comprehensive Processing and Modeling Pipeline

Silicon content plays an important role in determining the operational efficiency of blast furnaces (BFs) and their downstream processes in integrated steelmaking; however, existing sampling methods and first-principles models are somewhat limited in their capability and flexibility. Current data-based prediction models primarily rely on a limited set of manually selected furnace parameters. Additionally, different BFs present a diverse set of operating parameters and state variables that are known to directly influence the hot metal’s silicon content, such as fuel injection, blast temperature, and raw material charge composition, among other process variables that have their own impacts. The expansiveness of the parameter set adds complexity to parameter selection and processing. This highlights the need for a comprehensive methodology to integrate and select from all relevant parameters for accurate silicon content prediction. Providing accurate silicon content predictions would enable operators to adjust furnace conditions dynamically, improving safety and reducing economic risk. To address these issues, a two-stage approach is proposed. First, a generalized data processing scheme is proposed to accommodate diverse furnace parameters. Second, a robust modeling pipeline is used to establish a machine learning (ML) model capable of predicting hot metal silicon content with reasonable accuracy. The method employed herein predicted the average Si content of the upcoming furnace cast with an accuracy of 91% among 200 target predictions for a specific furnace provisioned by the XGBoost model. This prediction is achieved using only the past shift’s operating conditions, which should be available in real time. This performance provides a strong baseline for the modeling approach with potential for further improvement through provision of real-time features.

Chemistry↗
DOE OSTI2025

Advanced silicone materials for soft actuator applications

Soft actuators are at the forefront of the innovation tide in medicine, manufacturing, and aerospace because they are able to mimic the behavior of biological tissue and adapt to complex, unstructured environments. Of all the materials used, silicone-based elastomers have drawn enormous attention since they offer a superb combination of mechanical flexibility, biocompatibility, thermal stability, and long-term durability. In the past few years, there has also been a rapid pace of material evolution, additive manufacturing, and biointegration that has enhanced the performance and applications of silicone-based soft actuators. However, there is no focused and timely review compiling these advances. This review seeks to address that need by critically discussing recent advancements in advanced silicone materials, exploring new fabrication methodologies, and discussing emerging applications that range from wearable devices to implantable robotics. We also present suggestions for directions and the problems which must be addressed in order to further develop the performance and potential of silicone-based soft actuators, justifying the relevance and urgency of this effort.

biocompatibility↗
DOE OSTI2025

Electronic Melting of Silicon in Nanostructures using X-ray Forbidden Bragg Reflections

Abstract We carried out a short beamtime at the Pohang Accelerator Laboratory x-ray Free Electron Laser to perform a pump-probe (PP) laser excitation diffraction experiment on the silicon (222) forbidden Bragg peak. To limit the x-ray penetration, we used a “device layer” silicon film wafer bonded to a silicon substrate. The sample, specially fabricated by MEMC Electronic Materials, had a Si(100) substrate bonded to a 170 nm Si(100) film rotated at 45° for crystallographic isolation. A second sample was reactive-ion-etched down to 52 nm thickness. In the silicon lattice, the covalent bonds are seen exclusively at the 222 reflection. Upon laser excitation, these electrons are expected to be excited to the valence band on femtosecond electronic time scales. The Si(222) reflection is therefore expected to be extinguished on this fast time scale, while the electron–phonon coupled acoustic response is determined by the lattice dynamics. The latter is determined by the speed of sound over the device thickness, which is in the mid-picosecond range.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Photoelectrocatalytic reduction of CO 2 to formate using immobilized molecular manganese catalysts on oxidized porous silicon

The reduction of carbon dioxide (CO 2 ) to formate using molecular catalysts immobilized on high surface area porous silicon is described. Manganese complexes of the type ( R bpy)Mn(CO) 3 Br (bpy = 2,2′-bipyridine) were prepared with silatrane groups on the bpy ligand for attachment to oxide-coated porous silicon (SiO x -porSi). SiO x -porSi wafers were formed by heating hydrogen-terminated p-type porous silicon wafers under air, and the manganese complexes were immobilized on SiO x -porSi by heating at 80°C. The resulting hybrid photoelectrodes are photoelectrocatalysts for CO 2 reduction in acetonitrile containing 2.0 M triethylamine and 2.0 M isopropanol, yielding formate with high selectivity (>96%) and current density (∼0.6 mA/cm 2 ), excellent reproducibility, and a photovoltage of 280 mV at −1.75 V (versus ferrocenium/ferrocene) under 1 sun illumination. Here, the applied potential is close to the equilibrium potential for CO 2 reduction to formate. This work presents rare examples of immobilized molecular catalysts for CO 2 reduction to formate and the first on semiconducting silicon.

13 HYDRO ENERGY↗
DOE OSTI2025

Exciton fission enhanced silicon solar cell

While silicon solar cells dominate global photovoltaic energy production, their continued improvement is hindered by the single-junction limit. One possible solution is to use molecular singlet exciton fission to generate two electrons from each absorbed high-energy photon. We demonstrate that the long-standing challenge of coupling molecular excited states to silicon solar cells can be overcome using sequential charge transfer. Combining zinc phthalocyanine, aluminum oxide, and a shallow junction crystalline silicon microwire solar cell, the peak charge generation efficiency per photon absorbed in tetracene is (138% ± 6%), comfortably surpassing the quantum efficiency limit for conventional silicon solar cells and establishing a new, scalable approach to low-cost, high-efficiency photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2025

Low embodied energy and carbon, high lifetime silicon boules via a combined chemical vapor deposition/float zone process

This work evaluates a new process route to making float zone (Fz)-quality silicon wafers using a combination of computational fluid dynamics (CFD) modeling and technoeconomic analysis. Our analysis finds that the new process competes with Czochralski (Cz)-grown wafers on a levelized cost of energy system level. The new process also decreases embodied energy and carbon of silicon photovoltaics (PV) by ~6x circumventing the energy-costly Siemens process used in polycrystalline silicon (poly-Si) production plants to generate feedstock for Fz and Cz boules. Instead of using poly-Si from the Siemens process to feed crystallization, the new process uses the high-purity, trichlorosilane (TCS) precursor gas to grow a poly-Si feed rod in-situ during a modified Fz1,2 boule growth process. The gas-to-boule float zone process enables opportunity to produce high-purity (low metals and oxygen content), uniformly doped single crystal silicon boules and wafers with high bulk lifetimes (τ bulk > 15 ms) to enable higher efficiency cells (>27 %) with fewer known degradation mechanisms than Czochralski (Cz)-grown wafers. These benefits reduce the levelized cost of electricity (LCOE) of PV-produced electricity. Here we show the results of our CFD and chemical modeling of the process to prove feasibility and economic viability.

14 SOLAR ENERGY↗
DOE OSTI2025

Imaging the Acceptor Wave Function Anisotropy in Silicon

We present the first scanning tunneling microscopy (STM) image of hydrogenic acceptor wave functions in silicon. These acceptor states appear as square-ring-like features in STM images and originate from near-surface defects introduced by high-energy bismuth implantation into a silicon (001) wafer. Scanning tunneling spectroscopy confirms the formation of a p-type surface. Effective-mass and tight-binding calculations provide an excellent description of the observed square-ring-like features, confirming their acceptor character and attributing their symmetry to the light- and heavy-hole band degeneracy in silicon. A detailed understanding of the energetic and spatial properties of acceptor wave functions in silicon is essential for engineering large-scale acceptor-based quantum devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

First principles band structure of interacting phosphorus and boron/aluminum δ -doped layers in silicon

Silicon can be heavily doped with phosphorus in a single atomic layer (a δ layer), significantly altering the electronic structure of the conduction bands within the material. Recent progress has also made it possible to further dope silicon with acceptor-based δ layers using either boron or aluminum, making it feasible to create devices with interacting δ layers with opposite polarity. Using density functional theory, we calculate the electronic structure of a phosphorus-based δ layer interacting with a boron or aluminum δ layer, varying the distances between the δ layers. At separations 1 nm and smaller, the dopant potentials overlap and largely cancel each other out, leading to an electronic structure closely mimicking intrinsic silicon. At separations greater than 1 nm, the two δ layers behave independently of one another, with an equivalent electronic structure to a p–n diode with an intrinsic layer taking the place of the depletion region. One mechanism for charge transfer between δ layers at larger distances could be tunneling, where we see a tunneling probability exceeding what would be seen for a standard silicon 1.1 eV triangular barrier, indicating that the interaction between delta layers may enhance tunneling compared to a traditional junction.

delta layers↗
DOE OSTI2026

Tailored Silicone Network Architecture for Ultimate Mechanical Reinforcement

Hydrosilylation cured silicone elastomers are subject to reaction inefficiency, leading to incomplete and non-uniform crosslink networks, restricting the potential of mechanical reinforcement. This work investigates pre-synthesized, functional PDMS architectures as additives to improve ultimate mechanical performance relative to conventional single-step curing. Three custom, functional structures were prepared: a partially crosslinked PDMS scaffold (Structure A), a bottle-brush PDMS (Structure B), and a star-shaped PDMS derived from an MQ resin (Structure C). Rheological characterization was used to identify the ultimate design space and proper stoichiometric ratio for Structure A, and confirm successful formation of all structures for suitable incorporation into a base silicone formulation at 30wt%. Mechanical tests indicated that all three structures increased in ultimate tensile strength relative to their single-step counterparts, with Structure A providing additional improvements to toughness (432 vs. 258 kJ/m3) and ultimate elongation (158 vs. 115%). Furthermore, Structure B remained very soft in the unfilled state, while Structure C provided hardness (23 vs. 18 Shore A) and stiffness (780 vs. 420 kPa Young’s modulus) increases. In silica filled systems, Structure A retained increased strength but reduced elongation, while Structure B indicated strong reinforcement in terms of strength, toughness, and stiffness. Thermal analysis on the cure profiles of these materials suggested that pre-formation of network architectures enable a more complete reaction than a single-step process (15.9 vs. 15.1 J/g). Ultimately, these results indicate that tailoring PDMS architecture before the final cure can improve ultimate mechanical properties via improved network development in silicone elastomers. Furthermore, this work offers a promising strategy for designing higher-performance, more tunable silicone formulations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elastic strain engineering of lattice thermal conductivity of silicon: An ab-initio study

Silicon (Si) is the most essential material in the semiconductor industry. It is important to manage the thermal properties of crystalline Si. Elastic strain engineering (ESE) has proven to be an effective tool in controlling the electrical conductivity of Si in strained-silicon technology; its effects on the thermal conductivity of silicon, therefore, warrants careful investigation. The ESE effect is much more pronounced for nanostructured materials due to the ultralarge elastic strains (on the order of 10%) achievable at the nanoscale. In this work, the lattice thermal conductivity (κ L ) of Si under hydrostatic, biaxial, and uniaxial strain states is studied with ab-initio simulations, and the values of strain-dependent κ L compare well with experimental results and existing molecular dynamics simulations. To understand the mechanisms of strain-modulated κ L , the phonon bands, scattering rate, and Grüneisen parameters of phonon modes are computed. It is shown that strain can significantly change the anharmonicity of the crystal system, thus changing phonon scattering rates and κ L . Our results demonstrate that ESE can reduce silicon κ L by up to approximately 90%. Furthermore, uniaxial and biaxial strains can induce highly anisotropic thermal conductivity in Si, with relative variations up to 58.5% and 14.5%, respectively.

Anisotropy in Thermal Conductivity↗
DOE OSTI2026

Influence of silicon infiltration conditions on microstructure and mechanical properties in binder jet 3D printed SiC

Atmosphere, temperature, and hold time were varied for silicon infiltrated binder jet 3D printed SiC preforms. A two-step infiltration process optimized infiltration. The first step at 1450 °C under vacuum facilitated improved wetting. The second step at elevated temperature in argon advanced infiltration while suppressing vaporization. Variation of the second-step temperature (1550–1750 °C) and hold time revealed that 1550 °C for 1 h in argon following initial vacuum treatment yielded the highest silicon uptake ratio (∼96 %) with minimal residual porosity and strengths of 150–180 MPa. Flexural strength was either stable or improved with elevated temperatures up to 1000°C. In contrast, higher temperatures or extended hold times led to increased silicon vaporization and pores. The optimized process was applied to formulations with extra carbon to enhance SiC content and interconnectedness through reaction bonding, which corresponded to increased flexural strength. These findings provide guidance for silicon infiltration in additively manufactured SiC.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗