Search NASA⌕ Search

SEARCH · Search NASA

Results for “single-crystal diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

36 records · Page 2

Effects of wear on structure-sensitive magnetic properties of ceramic ferrite in contact with magnetic tape

Wear experiments and electron microscopy and diffraction studies were conducted to examine the wear and deformed layers in single-crystal Mn-Zn (ceramic) ferrite magnetic head material in contact with magnetic tape and the effects of that contact on magnetic properties. The crystalline state of the single-crystal magnetic head was changed drastically during the sliding process. A nearly amorphous structure was produced on its wear surface. Deformation in the surficial layer of the magnetic head was a critical factor in readback signal loss above 2.5 dB. The signal output level was reduced as applied normal load was increased. Considerable plastic flow occurred on the magnetic tape surface with sliding, and the signal loss due to the tape wear was approximately 1 dB.

Miyoshi, K.↗

Ordering Effects in NbC and TaC

By means of transmission electron microscopy and electron diffraction, evidence has been obtained for the existence of long range carbon atom ordering in single-crystal niobium carbide that has a carbon-to-metal ratio close to the integral composition Nb6C5. The ordering, which gives rise to superlattice and domain structures similar to those observed in V6C5, appears, however, only in samples that have been cooled slowly through the order-disorder temperature of 1025 C. In TaC of similar composition, the ordering, although present, remains very imperfect even after the crystals are subjected to the same thermal treatment. The results are interpreted in terms of the electronic structure of the transition metal carbides as it is currently understood, and their relevance to the mechanical properties of NbC and TaC are discussed.

Venables, J. D.↗

Adsorption of oxygen on W/100/ - Adsorption kinetics and structure

The adsorption of oxygen on W(100) single-crystal surfaces is studied by Auger electron spectroscopy (AES), flash desorption, low-energy electron diffraction (LEED), and retarding-field work-function measurements. The AES results reveal stepwise changes in the sticking coefficients in the coverage range 0 to 1 and activated adsorption at higher coverages. Upon room-temperature adsorption, a series of complex LEED patterns is observed. In layers adsorbed at 1050 K and cooled to room temperature, the p(2 x 1) structure is the first ordered structure observed. This structure shows a reversible order-disorder transition between 700 and 1000 K and is characterized by a work function which is lower than that of the clean surface. Heating room-temperature adsorbates changes their structure irreversibly. At temperatures below 750 K, some new structures are observed.

Bauer, E.↗

Second-generation Micro-Spec: Spectrometer Design for the Experiment for Cryogenic Large-Aperture Intensity Mapping

Micro-Spec (μ-Spec) is a direct-detection spectrometer that integrates all the components of a diffraction-grating spectrometer onto a ∼10-cm2 chip using superconducting microstrip transmission lines on a single-crystal silicon substrate. The second-generation μ-Spec has been designed to operate with a spectral resolution of ∼512 in the far-infrared and submillimeter (420–540 GHz, 714–555 μm) wavelength range, a band of interest for NASA’s EXperiment for Cryogenic Large-Aperture Intensity Mapping (EXCLAIM). EXCLAIM will be a high-altitude balloon mission that is being designed to map the emission of redshifted carbon monoxide and singly-ionized carbon lines over a redshift range 0 < z < 3.5. EXCLAIM will be the first demonstration of the μ-Spec technology in a space-like environment. This work reviews the status of the μ-Spec design for the EXCLAIM instrument, with emphasis on the spectrometer’s two-dimensional diffractive region, through which light of different wavelengths is focused on microwave kinetic inductance detectors (MKIDs) along the spectrometer focal plane. An optimization process generates a geometrical configuration of the diffractive region that satisfies specific requirements on size, operating spectral range and performance. An initial optical design optimized for EXCLAIM is presented in terms of geometric layout, spectral purity and efficiency.

Giuseppe Cataldo↗

Second-Generation Design of Micro-Spec: A Medium-Resolution, Submillimeter-Wavelength Spectrometer-on-a-Chip

Micro-Spec (μ-Spec) is a direct-detection spectrometer which integrates all the components of a diffraction-grating spectrometer onto a ∼10-cm2 chip through the use of superconducting microstrip transmission lines on a single-crystal silicon substrate. A second-generation μ-Spec is being designed to operate with a spectral resolution of 512 in the submillimeter (500-1000 μm, 300-600 GHz) wavelength range, a band of interest for several spectroscopic applications in astrophysics. High altitude balloon missions would provide the first test bed to demonstrate the μ-Spec technology in a space-like environment and would be an economically viable venue for multiple observation campaigns. This work reports on the current status of the instrument design and will provide a brief overview of each instrument subsystem. Particular emphasis will be given to the design of the spectrometer's two-dimensional diffractive region, through which the light of different wavelengths is focused on the detectors along the focal plane. An optimization process is employed to generate geometrical configurations of the diffractive region that satisfy specific requirements on spectrometer size, operating spectral range, and performance. An optical design optimized for balloon missions will be presented in terms of geometric layout, spectral purity, and efficiency.

Cataldo, G.↗

Optically erasable and rewritable solid-state holograms.

Optical holographic storage in single-crystal LiNbO3 is described which can be optically erased at room temperature and then rewritten with no degradation in efficiency or writing rate. The diffraction efficiencies associated with the process are about 0.0001. Some variations from previously obtained results include a lack of threshold power density for writing, very-long-term persistence of the stored hologram, and a lack of a dependence of the diffracted intensity on the polarization of the readout beam.

Gaylord, T. K.↗

Temperature dependence of gamma-gamma prime lattice mismatch in nickel-base superalloys

High temperature X-ray diffraction techniques were used to determine the gamma-gamma prime lattice mismatch of three different nickel-base superalloys at temperatures between 18 and 1000 C. The measurements were performed on oriented single-crystal disks which had been aged to produce a semicoherent gamma-gamma prime structure. The thermal expansion of the lattice parameters of the gamma and gamma-prime phases was described by a second-order polynomial expression. The expansion of the gamma-prime phase was consistently smaller than that of the gamma phase, which caused the lattice mismatch to become more negative at higher temperatures. It was also shown that high values of lattice mismatch resulted in increased rates of directional gamma-prime coarsening during elevated temperature creep exposure.

Nathal, M. V.↗

Ternary Feldspar Within Felste Clasts From Apollo Impact Melt Breccia 72255

Granitic clasts with unique ternary feldspar compositions have been identified within samples of the layered impact melt breccia from Apollo 17 Station 2 Boulder 1 (72215, 72235, 72255 and 72275), and in a felsite clast from station 3 (73215). These “ternary” compositions seemingly plot within the miscibility gap of the albite-anorthite-orthoclase (Ab-An-Or) system. Feldspars with these compositions have not been identified in terrestrial samples, and equilibrium feldspar compositions from laboratory experiments indicate they would not be thermodynamically stable. Thus, the physiochemical processes involved in forming these unique ternary feldspars remain poorly understood. To better constrain the formation of ternary feldspar within lunar breccias, we have undertaken a coordinated scanning electron microscope (SEM)-based coupled electron backscatter diffraction (EBSD) and energy dispersive spectrometry (EDS), electron microprobe analyzer (EPMA) wavelength dispersive spectrometry, and transmission electron microscopy (TEM) study. The goals of this study are twofold: 1) confirm whether ternary feldspar is present as coherent, single-crystals or sub-microscopic intergrowths of normal compositions, and 2) better constrain the formation conditions of clasts containing ternary feldspar.

T. M. Erickson↗

The adsorption and early stages of condensation of Ag and Au on W single-crystal surfaces

Silver and gold were evaporated up to several monolayers in thickness onto W single-crystal surfaces of the 110 and 100 plane types in the temperature range between 300 and 1300 K. The mode of growth and the structure of the layers were studied by Auger electron spectroscopy and low-energy electron diffraction. The results are compared with thermal desorption spectroscopy data and work-function change measurements. They show certain similarities but also some striking differences between the two systems Ag/W and Au/W as well as a strong crystallographic anisotropy of adsorption and condensation.

Bauer, E.↗

Microstructural investigations of light-emitting porous Si layers

The structural and morphological characteristics of visible-light-emitting porous Si layers produced by anodic and stain etching of single-crystal Si substrates are compared using transmission electron microscopy and atomic force microscopy (AFM). AFM of conventionally anodized, laterally anodized and stain-etched Si layers show that the layers have a fractal-type surface morphology. The anodized layers are rougher than the stain-etched films. At higher magnification 10 nm sized hillocks are visible on the surface. Transmission electron diffraction patterns indicate an amorphous structure with no evidence for the presence of crystalline Si in the near-surface regions of the porous Si layers.

George, T.↗

Failure Morphologies of Cyclically Oxidized ZrO2-Based Thermal Barrier Coatings

Advanced and baseline thermal barrier coatings (TBCs) were thermal cycle tested in air at 1163 C until delamination or spallation of the ceramic top coat. The top coat of the advanced TBC s consisted of ZrO2 with various amounts of Y2O3, Yb2O3, Gd2O3, or Nd2O3 dopants. The composition of the top coat of the baseline TBC was ZrO2-8wt.%Y2O3. All top coats were deposited by air plasma spraying. A NiCrAlY or NiCoCrAlY bond coat was deposited by low pressure plasma spraying onto a single-crystal, Ni-base superalloy. The TBC lifetime for the baseline coatings was approximately 190 cycles (45 minutes at 1163 C per cycle) while the lifetime for the advanced coatings was as high as 425 cycles. The fracture surfaces and sample cross sections were examined after TBC failure by SEM and optical microscopy, and the top coats were further examined by X-ray diffraction. These post-test studies revealed that the fracture path largely followed splat boundaries with some trans-splat fracture. However, there were no obvious distinguishing features which explained the difference in TBC lifetimes between some of the advanced and baseline coatings.

Nesbitt, James A.↗

Silicide surface phases on gold

The crystalline silicide layers formed on (111) and (100) surfaces of Au films on various Si single-crystal substrates are studied by LEED and AES in conjunction with sputter-depth profiling as a function of annealing temperature. On the (111) surface, three basic silicide structures are obtained corresponding to layers of various thicknesses as obtained by different preparation conditions. The (100) surface shows only two different structures. None of the structures is compatible with the various bulk silicide structures deduced from X-ray diffraction. Using LEED as a criterion for the presence or absence of silicide on the surface, smaller layer thicknesses are obtained than reported previously on the basis of AES studies.

Green, A. K.↗

CFD Growth of 3C-SiC on 4H/6H Mesas

This article describes growth and characterization of the highest quality reproducible 3C-SiC heteroepitaxial films ever reported. By properly nucleating 3C-SiC growth on top of perfectly on-axis (0001) 4H-SiC mesa surfaces completely free of atomic scale steps and extended defects, growth of 3C-SiC mesa heterofilms completely free of extended crystal defects can be achieved. In contrast, nucleation and growth of 3C-SiC mesa heterofilms on top of 4H-SiC mesas with atomic-scale steps always results in numerous observable dislocations threading through the 3C-SiC epilayer. High-resolution X-ray diffraction and transmission electron microscopy measurements indicate non-trivial in-plane lattice mismatch between the 3C and 4H layers. This mismatch is somewhat relieved in the step-free mesa case via misfit dislocations confined to the 3C/4H interfacial region without dislocations threading into the overlying 3C-SiC layer. These results indicate that the presence or absence of steps at the 3C/4H heteroepitaxial interface critically impacts the quality, defect structure, and relaxation mechanisms of single-crystal heteroepitaxial 3C-SiC films.

Neudeck, Philip G.↗

Evaluation of silicon ribbon material for solar cell fabrication

Optical microscopy, electron microscopy, and X-ray diffraction were utilized to characterize silicon ribbon structure. Complex twin formation was observed in nearly all ribbons examined. Twins formed in the 110-plane 112-line ribbon orientation appear stable, and this orientation may be preferable when the ribbon is utilized for solar cells. In addition to twinning, grain boundaries and other structural defects were observed in the ribbon material. Hall effect, resistivity, spreading resistance, surface photovoltage, and solar cell electrical/optical measurements were performed on ribbon samples and correlated with structural and ribbon growth characteristics. Only those ribbon samples with either single-crystal structure or with 'parallel' twin formations were capable of solar-cell performance approaching that of Czochralski material.

Leipold, M.↗

Interaction of metal layers with polycrystalline Si

Solid-phase reactions of metal films deposited on 0.5-micron-thick polycrystalline layers of Si grown by chemical vapor deposition at 640 C were investigated by MeV He-4 backscattering spectrometry, glancing angle X-ray diffraction, and SEM observations. For the metals Al, Ag, and Au, which form simple eutectics, heat treatment at temperatures below the eutectic results in erosion of the poly-Si layer and growth of Si crystallites in the metal film. Crystallite formation is observed at temperatures exceeding 550 C for Ag, at those exceeding 400 C for Al, and at those exceeding 200 C for Au films. For Pd, Ni, and Cr, heat treatment results in silicide formation. The same initial silicides (Pd2Si, Ni2Si, and CrSi2), are formed at similar temperatures on single-crystal substrates.

Nakamura, K.↗

A Compact X-Ray System for Support of High Throughput Crystallography

Standard x-ray systems for crystallography rely on massive generators coupled with optics that guide X-ray beams onto the crystal sample. Optics for single-crystal diffractometry include total reflection mirrors, polycapillary optics or graded multilayer monochromators. The benefit of using polycapillary optic is that it can collect x-rays over tile greatest solid angle, and thus most efficiently, utilize the greatest portion of X-rays emitted from the Source, The x-ray generator has to have a small anode spot, and thus its size and power requirements can be substantially reduced We present the design and results from the first high flux x-ray system for crystallography that combine's a microfocus X-ray generator (40microns FWHM Spot size at a power of 45 W) and a collimating, polycapillary optic. Diffraction data collected from small test crystals with cell dimensions up to 160A (lysozyme and thaumatin) are of high quality. For example, diffraction data collected from a lysozyme crystal at RT yielded R=5.0% for data extending to 1.70A. We compare these results with measurements taken from standard crystallographic systems. Our current microfocus X-ray diffraction system is attractive for supporting crystal growth research in the standard crystallography laboratory as well as in remote, automated crystal growth laboratory. Its small volume, light-weight, and low power requirements are sufficient to have it installed in unique environments, i.e.. on-board International Space Station.

Ciszak, Ewa↗

Stability of Y-Ba-Cu-oxide phases in salt flux

The results of an investigation into the possibility of growing YBa2Cu3O7 (or Y123) single crystals from a NaCl-KCl flux (salt flux) are presented. They are compared with results for Y123 crystals grown from a Ba-Cu-oxide flux system. The chosen salt flux composition was 1:1 (NaCl:KCl). The preparation method of the solutes is presented, with particular attention given to the compounds surrounding the Y123 phase, such as Y2BaCuO6 (Y211). Optical microscopy was introduced to study the morphology of the sample; X-ray diffraction was used for phase identification; and a chemical analysis was effected. The Y123, Y211, and BaCuO2 phases were shown to be dissociated in the NaCl-KCl flux, and could not be recrystallized. A small amount of the flux could be added to create large-grain Y123 crystals, but single-crystal growth was not possible in a top-seeded NaCl-KCl solution. This is attributed to significant differences in solubility of the crystal elements, and phase separation caused by CuO crystal formation.

Tao, Y. K.↗

Synthesis, Structure, Characterization, and Decomposition of Nickel Dithiocarbamates: Effect of Precursor Structure and Processing Conditions on Solid-State Products

Single-crystal X-ray structures of four nickel dithiocarbamate complexes, the homoleptic mixed-organic bis-dithiocarbamates Ni[S2CN(isopropyl)(benzyl)]2, Ni[S2CN(ethyl)(n-butyl)]2, and Ni[S2CN(phenyl)(benzyl)]2, as well as the heteroleptic mixed-ligand complex NiCl[P(phenyl)3][(S2CN(phenyl)(benzyl)], were determined. Synthetic, spectroscopic, structural, thermal, and sulfide materials studies are discussed in light of prior literature. The spectroscopic results are routine. A slightly distorted square-planar nickel coordination environment was observed for all four complexes. The organic residues adopt conformations to minimize steric interactions. Steric effects also may determine puckering, if any, about the nickel and nitrogen atoms, both of which are planar or nearly so. A trans-influence affects the Ni-S bond distances. Nitrogen atoms interact with the CS2 carbons with a bond order of about 1.5, and the other substituents on nitrogen display transoid conformations. There are no strong intermolecular interactions, consistent with prior observations of the volatility of nickel dithiocarbamate complexes. Thermogravimetric analysis of the homoleptic species under inert atmosphere is consistent with production of 1:1 nickel sulfide phases. Thermolysis of nickel dithiocarbamates under flowing nitrogen produced hexagonal or -NiS as the major phase; thermolysis under flowing forming gas produced millerite (-NiS) at 300 C, godlevskite (Ni9S8) at 325 and 350 C, and heazlewoodite (Ni3S2) at 400 and 450 C. Failure to exclude oxygen results in production of nickel oxide. Nickel sulfide phases produced seem to be primarily influenced by processing conditions, in agreement with prior literature. Nickel dithiocarbamate complexes demonstrate significant promise to serve as single-source precursors to nickel sulfides, a quite interesting family of materials with numerous potential applications.

microscopy↗