Search NASA⌕ Search

SEARCH · Search NASA

Results for “slot die coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
DOE OSTI2023

Eco–Friendly Solvent Engineered CsPbI 2.77 Br 0.23 Ink for Large–Area and Scalable High Performance Perovskite Solar Cells

The performance of large-area perovskite solar cells (PSCs) has been assessed for typical compositions, such as methylammonium lead iodide (MAPbI 3 ), using a blade coater, slot-die coater, solution shearing, ink-jet printing, and thermal evaporation. However, the fabrication of large-area all-inorganic perovskite films is not well developed. This study develops, for the first time, an eco-friendly solvent engineered all-inorganic perovskite ink of dimethyl sulfoxide (DMSO) as a main solvent with the addition of acetonitrile (ACN), 2-methoxyethanol (2-ME), or a mixture of ACN and 2-ME to fabricate large-area CsPbI 2.77 Br 0.23 films with slot-die coater at low temperatures (40–50 °C). The perovskite phase, morphology, defect density, and optoelectrical properties of prepared with different solvent ratios are thoroughly examined and they are correlated with their respective colloidal size distribution and solar cell performance. Here, the optimized slot-die-coated CsPbI 2.77 Br 0.23 perovskite film, which is prepared from the eco-friendly binary solvents dimethyl sulfoxide:acetonitrile (0.8:0.2 v/v), demonstrates an impressive power conversion efficiency (PCE) of 19.05%. Moreover, the device maintains ≈91% of its original PCE after 1 month at 20% relative humidity in the dark. It is believed that this study will accelerate the reliable manufacturing of perovskite devices.

binary and ternary solvent↗
DOE OSTI2023

Manipulating Organic Semiconductor Morphology with Visible Light

A method is presented to manipulate the final morphology of roll-to-roll slot-die coated poly(3-hexylthiophene) (P3HT) by optically exciting the p-type polymer in solution while coating. These results provide a comprehensive picture of the entire knowledge chain, from demonstrating how to apply the authors’ method to a fundamental understanding of the changes in morphology and physical properties induced by exciting P3HT while coating. By combining results from density functional theory and molecular dynamics simulations with a variety of X-ray experiments, absorption spectroscopy, and THz spectroscopy, the relationship between morphology and physical properties of the thin film is demonstrated. Specifically, in P3HT films excited with light during deposition, changes in crystallinity and texture with more face-on orientation and increased out-of-plane charge mobility are observed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Impact of Salt Chemistry and Interlayer Architecture on Solid Electrolyte Interphase Composition and Performance

Reversible lithium metal anodes require interphases that are chemically stable, mechanically robust, and compatible with scalable processing. Here, we use slot-die-coated, salt-rich PEO interlayers to design SEI nanolayers on Cu current collectors and isolate how salt anion chemistry controls interphase composition and lithium plating/stripping behavior in architectures relevant to Li plating and anode-free cells. Mesoscale modeling shows that dendrite initiation at SEI defects is governed by a tradeoff among interphase thickness, ionic conductivity, and stiffness through defect-driven current focusing, motivating controlled formation from thin precursor layers. Using UHV-transferred XPS and ToF-SIMS depth profiling after controlled Li deposition, we find that fluorinated sulfonylimide salts (LiTFSI, LiFSI) form mixed inorganic/organic interphases containing LiF and PEO-derived alkoxides, with LiFSI producing a more LiF-dominant Li-facing surface than LiTFSI under identical conditions. In contrast, LiNO 3 -containing interlayers yield a comparatively thick nitrate-derived interphase that reduces upon Li contact to an N-rich inorganic layer (Li–N/N 3− , LiN x O y ). In Cu| |Li cells, these designed interlayers reduce interfacial resistance and improve Coulombic efficiency (CE) and critical current density (CCD) relative to uncoated controls, with LiFSI- and LiNO 3 -based interlayers providing the highest CE/CCD. Overall, the results demonstrate a manufacturing-relevant approach to engineer SEI nanolayers by salt chemistry, providing pathways to improve reversible lithium metal anodes while reducing reliance on LiTFSI.

anion chemistry↗
DOE OSTI2022

Versatile acid solvents for pristine carbon nanotube assembly

Chlorosulfonic acid and oleum are ideal solvents for enabling the transformation of disordered carbon nanotubes (CNTs) into precise and highly functional morphologies. Currently, processing these solvents using extrusion techniques presents complications due to chemical compatibility, which constrain equipment and substrate material options. Here, we present a novel acid solvent system based on methanesulfonic or p-toluenesulfonic acids with low corrosivity, which form true solutions of CNTs at concentrations as high as 10 g/liter (≈0.7 volume %). The versatility of this solvent system is demonstrated by drop-in application to conventional manufacturing processes such as slot die coating, solution spinning continuous fibers, and 3D printing aerogels. Through continuous slot coating, we achieve state-of-the-art optoelectronic performance (83.6 %T and 14 ohm/sq) at industrially relevant production speeds. This work establishes practical and efficient means for scalable processing of CNT into advanced materials with properties suitable for a wide range of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Comprehensive evaluation of commercially scalable atomic-layer-deposited alumina coating impact on full cell battery performance across varied test conditions

Atomic Layer Deposition (ALD) has emerged as a strategic enhancement method for lithium-ion battery (LIB) materials offering potential benefits and durability benefits for industrial battery production. However, the translation from laboratory achievements to commercial-scale applications has been limited. Here, this study aims to bridge this gap by comprehensively evaluating the effects of commercially scalable Al 2 O 3 ALD coatings using full pouch cell performance as a means to assess the ALD impact. We utilized large-scale slot-die coating techniques to ensure consistent electrode quality and tested four configurations of pouch cells to analyze the individual effects of ALD coating on anode and cathode electroactive materials. Our extensive testing matrix included long-term cycling, fast discharge, fast charge, leakage current, and high voltage tests. While at lower C-rates (<~1C), the influence of Al 2 O 3 coatings on cell performance is not significant. Fast charging conditions reveal that the anode ALD coating significantly enhances performance via a passivating effect, while on the cathode, it is detrimental, potentially due to increased resistance of the thin interfacial layer formed during the ALD processing. Leakage current and high-voltage tests show that the application of ALD coatings on either anode or cathode effectively minimizes side reactions at the electrode-electrolyte interface. Additionally, ALD coatings significantly mitigate concentrated and localized lithium plating on the anodes. These insights provide a valuable understanding of the potential of ALD technologies in LIB manufacturing to tailor cell performance, paving the way for safer, more efficient, and cost-effective battery solutions.

25 ENERGY STORAGE↗
DOE OSTI2022

High‐Performance Green Thick‐Film Ternary Organic Solar Cells Enabled by Crystallinity Regulation

Abstract The power conversion efficiency (PCE) of organic solar cells (OSCs) has reached high values of over 19%. However, most of the high‐efficiency OSCs are fabricated by spin‐coating with toxic solvents and the optimal photoactive layer thickness is limited to 100 nm, limiting practical development of OSCs. It is a great challenge to obtain ideal morphology for high‐efficiency thick‐film OSCs when using non‐halogenated solvents due to the unfavorable film formation kinetics. Herein, high‐efficiency ternary thick‐film (300 nm) OSCs with PCE of 15.4% based on PM6:BTR‐Cl:CH1007 are fabricated by hot slot‐die coating using non‐halogenated solvent (o‐xylene) in the air. Compared to PM6:BTR‐Cl:Y6 blends, the stronger pre‐aggregation of CH1007 in solution induces the earlier aggregation of CH1007 molecules and longer aggregation time, and thus results in high and balanced crystallinity of donors and acceptor in CH1007‐based ternary film, which led to high‐carrier mobility and suppressed charge recombination. The ternary strategy is further used to fabricate high‐efficiency, thick‐film, large‐area, and flexible devices processed from non‐halogenated solvents, paving the way for industrial development of OSCs.

Chemistry↗
DOE OSTI2025

In Situ Electrochemistry of Buried Interfaces in Metal Halide Perovskites: Probing Energy Bands, Halide Redox Activity, and Kinetics

Control over charge injection and extraction processes across buried interfaces is fundamental for all (opto)electronic multilayer device platforms, necessitating detailed understanding of local structural and chemical differences that promote defect formation, distort energetic band-edge alignments, and alter charge transport processes. Herein, the implementation of a low-cost electroanalytical methodologies’ tool suite is described to quantitatively characterize buried interfaces and redox reactions in printable, mixed electrical–ionic, and redox-active metal halide perovskites and a prototypical hole-transporting nickel oxide (NiO x ) thin film. The objective is to demonstrate the power of electrochemical methodologies to improve the nanoscale understanding of complex interfaces within optoelectronic devices by providing case studies on how to: i) differentiate between electronic and chemical properties in NiO x contacts; ii) measure changes in reversibility of halide redox reactions via NiO x surface states; iii) assess energy alignment and charge transport across (modified) buried interfaces; and iv) quantify defects at buried interfaces that change with modifiers and differences in perovskite processing, including increasing defect concentrations when films are slot-die-coated versus spin-cast. The collective approach addresses major challenges in understanding the precise energy landscape and interface reactivity under relevant electric fields that mimic operando conditions (away from equilibrium) and across length scales in thin film device formats.

(spectro)electrochemistry↗
DOE OSTI2020

Application of electrospinning for the fabrication of proton-exchange membrane fuel cell electrodes

We report electrospun materials have been gaining great interest in the energy sector. Their tunability and robustness make them highly attractive, particularly for proton-exchange membrane fuel cell (PEMFC) electrodes. Conventional PEMFC electrodes, prepared by either spraying, painting, or slot-die coating, have not yet met the needs of large-scale PEMFC use. Electrospinning of fibrous materials has already shown great promise as an alternative methodology for electrode fabrication. Electrospinning has been used in fuel cell electrodes through two primary means: (1) segmented carbon or inorganic fibers to serve as precious metal catalyst support, and (2) high aspect ratio polymer/particle fibers to serve directly as the electrode. The use of electrospun fibrous electrodes has led to improved PEMFC durability and increased power output at low catalyst loadings, both of which are of paramount importance to large-scale commercialization of PEMFC electric vehicles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of high-performance roll-to-roll-coated gas-diffusion-electrode-based fuel cells

This study focuses on determining fabrication conditions to create high-performance roll-to-roll-coated (R2R-coated) gas-diffusion electrodes (GDEs) for proton-exchange-membrane fuel cells (PEMFCs). Here, we examine how process conditions influence the distribution of ionomer in the electrode, which is shown to be critical for high performance. Using a combination of Kelvin probe, X-ray photoelectron spectroscopy, and nano-scale X-ray computed tomography we show that formation of an ionomer-rich surface is promoted by using a higher drying rate. We show that R2R-coated GDEs have higher surface ionomer concentration than spray-coated GDEs, which enables these R2R-coated GDEs to not need an additional ionomer overlayer, as is typically the case for spray-coated GDEs. This will reduce the number of processing steps and lower material costs in a manufacturing setting. This work shows that with the appropriate selection of materials, ink formulation, and processing conditions, direct-coated GDEs are a viable pathway for fuel cell manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Roll to Roll (R2R) Manufacturing of Electrolysis Electrodes for Low Cost Hydrogen Production: Cooperative Research and Development Final Report, CRADA Number CRD-18-00780

NREL, Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL), which are also referred to collectively herein as the "Contractors" will perform electrode ink development and characterization, focusing on 1) inks with appropriate properties for R2R (gravure and slot-die) coating onto PFSA membrane and 2) catalysts suitable for electrolysis. Participant will develop acceptance criteria and characterization methods for direct coating on the membrane. The purpose of this project is to show feasibility for cost reduction of the electrode through increased throughput and improved material utilization. Successful completion of this project will result in more affordable hydrogen production via proton exchange membrane (PEM) electrolysis by substantially reducing the anode precious metal content and catalyst-coated membrane processing costs. Assists laboratory in achieving programmatic scope, adds new capability to the laboratory's core competencies. This project uses and enhances the laboratory's core competencies, and enhances U.S. competitiveness by utilizing DOE developed intellectual property and/or capabilities. This project will benefit the Fuel Cell subprogram within the EERE Fuel Cell Technologies Office (FCTO) by actively developing materials, formulations, components, and processes for PEM electrolyzer stacks for overcoming critical technical barriers to widespread hydrogen production for zero-emission transportation applications. Through this JWS, NREL, ANL and ORNL are assisting a key domestic industry partner, Proton Energy Systems, Inc., in the area of low-cost electrolyzer electrode formulation and coating technology. After completion of this project, NREL, ANL and ORNL will be able to verify whether the direct deposit coating processes investigated are suitable for producing CCMs for PEM electrolyzers, which is of great interest and benefit to the DOE EERE Fuel Cell Technologies Office (FCTO) and H2@Scale missions.

08 HYDROGEN↗
DOE OSTI2026

Roll-to-Roll Manufacturing of Solid Oxide Fuel Cells

The overall goal of this project is to develop a high-volume electrode electrolyte assembly (EEA) production capability to significantly increase throughput of solid oxide fuel cell (SOFC) manufacturing and reduce the cost while maintaining the same level of performance. Specifically, four approaches will be adopted: 1) optimization of the lamination process and correlation of the EEA properties and performance with the lamination conditions; 2) scale up of the lamination process and demonstration of >10 ft of EEA; 3) further increase of the EEA throughput via slot-die coating and demonstration of > 5 m/min in coating the thick anode layer; and 4) minimization of the anode thickness to reduce material cost.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Uniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers

This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mg Ir cm −2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mg Ir cm −2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.

08 HYDROGEN↗
DOE OSTI2023

Advanced electrode manufacturing to enable low cost PEM electrolysis

A critical challenge for the implementation of proton exchange membrane (PEM)-based water electrolyzers for the H2@Scale vision is the capital cost, which is largely driven by related factors of overdesign and highly manual legacy manufacturing methods. Typical electrolyzer cells have an order of magnitude higher membrane thickness and catalyst loading vs. fuel cells, in part because the manufacturing methods being used are not capable of producing uniform and reliable electrodes on thin membranes with low loading. Advanced electrode manufacturing is therefore the key enabler to reduce the cost of the electrolyzer stack, particularly roll-to-roll (R2R) manufacturing of catalyst coated layers (CCLs) and catalyst coated membranes (CCMs). The electrolyzer manufacturing process still relies on traditional sheet-to-sheet (S2S) processes, which requires intensive labor to make parts to meet the specification requirements. This project leverages fuel cell expertise (GM) with Proton’s knowledge of electrolyzer components to develop the electrocatalyst ink formulations and coating processes using slot die (ORNL) and gravure (NREL) coatings, with proof of concept at the pilot-scale (Kodak).

08 HYDROGEN↗
DOE OSTI2025

Precursor Engineering of All-Inorganic Perovskite Absorber and Rapid Photonic Annealing for Large-Area Highly Stable Perovskite Solar Modules

Currently the all-inorganic perovskites were prepared by toxic dimethylformamide (DMF) as a main solvent, and small-area PSCs were prepared by a simple spin-coating method followed by lengthy thermal annealing. All these issues limited the commercialization of these PSCs. Therefore, it is necessary to develop an eco-friendly all-inorganic perovskite ink that can be coated over large areas at low temperatures followed by rapid annealing for the scale-up manufacturing with high compatibility to the industrial scale sheet-to-sheet or roll-to-roll processes.

14 SOLAR ENERGY↗
DOE OSTI2020

Influence of Coating Method on the Performance of Roll-to-Roll Coated PEM Fuel Cell Catalyst Layers

As production of fuel cell vehicles and power systems increases there is a need to understand the process science of fuel cell manufacturing. Industrial production of polymer electrolyte membrane fuel cell (PEMFC) electrodes will rely on continuous roll-to-roll (R2R) coating methods to meet the rates needed for mass production. There are a variety of coating methods that could be used to coat catalyst layers. The different physics of each method may result in different morphologies and performance. Here we present the results of a study comparing fuel cell catalyst layers coated using two R2R coating methods: slot-die and gravure. These two methods were selected because the physics of applying the liquid to the substrate is very different between the two cases. Pt/C catalysts layers were coated directly onto carbon-fiber gas diffusion media to create gas diffusion electrodes (GDEs), without the use of a decal transfer process. These GDEs were assembled into membrane electrode assemblies (MEAs) by hot pressing to Nafion membranes. In situ performance and other electrochemical diagnostics were used to determine the influence of coating method on catalyst layer electrochemical properties. Electron microscopy was utilized to understand the influence of coating method on electrode morphology and its influence on electrochemical properties. We also explored the influence of solvent ratio to understand the potential coupling between ink formulation and coating methodology.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE↗