Search NASA⌕ Search

SEARCH · Search NASA

Results for “small fission reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗
DOE OSTI2023

Digital Twins for Nuclear Power Plants and Facilities

The nuclear digital twin (DT) is the virtual representation of a nuclear energy system across its lifecycle. The nuclear DT uses real-time information and other data sources to improve the process of design, licensing, construction, security, O&M, decommissioning, and waste disposal. By leveraging the knowledge base and experience from the past 40 years of LWR operation, the nuclear DT is helping to accelerate the development and deployment of advanced nuclear technology in areas of passive safety, new fuel forms, instrumentation, and reactor control. For the currently operating nuclear fleet, DTs are reducing the operational risks, increasing plant availability, increasing energy capability, and reducing electricity production costs. For advanced fission and fusion reactors, DTs are being used to design for passive safety and built-in security-by-design. Rapidly deployable small modular reactor (SMR) and microreactor designs compatible with modular construction techniques and advanced manufacturing will be the new normal, reducing the need for large capital expenditures and compressing construction schedules. In addition, lower operational and maintenance costs will be realized by reducing the complexity of operations, staffing needs, and maintenance-related activities.

Kropaczek, Dave↗
DOE OSTI2020

Microstructure, Thermal, and Mechanical Properties Relationships in U and UZr Alloys (Final Report)

Uranium-zirconium (U-Zr) alloys are candidate fuel systems for transmutation based reactors that can be used to burn long-lived minor actinides and fission products in fast spectrum reactors. Metallic fuels have also been gaining more recent attention for applications as accident tolerant fuels, as well as for use in small modular reactors. This research focused on a “science-based” approach to capture the connections between U and U-Zr alloys’ three-dimensional (3-D) microstructure, thermal properties, and mechanical properties through closely coordinated experiments and modeling efforts from the unirradiated to the irradiated fuels. Advanced characterization and modeling techniques were used to understand irradiation-induced microstructural evolution and its direct impact on the thermal and mechanical properties of U and U-Zr fuel. Closely coordinated experiments and modeling were performed to provide crucial data that does not currently exist. Overall, this research spanned multiple length and time scales within the models and experiments. The scope of the research encompassed the understanding of the irradiation effects in U and various U-Zr alloys with particular attention paid to three task areas: (1) microstructural evolution, (2) in-situ/ex-situ thermal and mechanical properties, and (3) multiscale modeling connections to microstructure, thermal, and mechanical properties. This research resulted in (1) the 3-D characterization of neutron irradiated U-Zr fuel in multiple phase regions to better understand fission gas swelling and constituent redistribution, (2) development of a microstructural model linking thermal and mechanical properties via in situ Raman and nanoindentation, (3) and mesoscale phase field modeling was coupled with the AEH method in the MOOSE framework was used to calculate the effective thermal conductivities of U-Zr fuels consisting of α-U and δ-UZr 2 heterogeneous microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Commercial integration of advanced nuclear energy with Artificial Intelligence (AI): Possible implications

The integration of advanced nuclear technologies (both fission and fusion) with artificial intelligence (AI) presents unprecedented national security challenges and opportunities. As fusion energy approaches commercial viability alongside advanced Small Modular Reactors (SMRs), their integration with AI and Artificial General Intelligence (AGI) systems could fundamentally transform the global energy and AI landscapes — two pillars of national security. This document briefly examines how AI could accelerate nuclear energy development and deployment while altering existing power structures, a lot could be done to deepen the discussions. Simultaneously, it observes how nuclear-powered AI may expedite advances toward AGI and beyond. These issues are deeply interconnected and thus need to be examined as a whole and more comprehensively than what’s being summarized here. For instance, AI-powered autonomous operation of nuclear facilities could reduce human error but introduce new cybersecurity vulnerabilities and uncertainties. Further investigation would also address how AI-enhanced nuclear technologies might complicate proliferation concerns through advanced fuel cycle management, nuclear materials production and safeguard. The strategic advantage gained by first entities achieving successful AI-nuclear integration could reshape global and national security framework. Timely analysis of these implications may be crucial for policymakers seeking to harness these technologies' benefits while effectively mitigating their potential risks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Analysis of near-field and far-field aerosol dispersion for microreactors

The current paper presents a simulation-based analysis of aerosol dispersion in the near-field and far-field of a generic, conceptual microreactor operating at pressures close to the ambient pressure; therefore, in the event of an accident that causes radionuclide leakage from the microreactor containment, the radionuclide particles are less likely to travel too far from the reactor, as opposed to conventional reactors. Accordingly, the presented work provides estimates of average and 95-percentile values of the relative effluent concentration. A parametric study is then performed to narrow down the parameters which affect the aerosol dispersion characteristics most significantly. Simulations were performed in the computer code ARCON96, and the parameters found to affect aerosol dispersion characteristics are the atmospheric stability class, and the distance between the release point and the receptor. It is recommended that the computer code RADTRAD be used to calculate actual dosage over distance, using the outputs from ARCON96 as inputs, along with reactor-specific core term inventories. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Kilopower - Powering the Future of Space Exploration [Poster]

The Kilopower Project was initiated by NASA’s Space Technology Mission Directorate to demonstrate subsystem-level technology readiness of small space fission power in a relevant environment (TRL 5) for space science and human exploration power needs. The Kilopower Project centerpiece is the Kilowatt Reactor Using Stirling Technology (KRUSTY) test, which consists of the development and testing of a ground technology demonstrator of a 1 kWe class fission power system. The technologies to be developed and validated by KRUSTY are extensible to space fission power systems from 1 to 10 kWe, which can enable modular surface fission power systems for human exploration, as well as higher power future potential deep space science missions.

42 ENGINEERING↗
DOE OSTI2020

Kilopower Project: The KRUSTY Fission Power Experiment and Potential Missions

The Kilopower Project was initiated by NASA’s Space Technology Mission Directorate/Game Changing Development Program in fiscal year 2015 to demonstrate subsystem-level technology readiness of small space fission power in a relevant environment (Technology Readiness Level 5) for space science and human exploration power needs. The Kilopower Project centerpiece is the Kilowatt Reactor Using Stirling TechnologY (KRUSTY) test, which consists of the development and testing of a ground technology demonstrator of a 1-kW(electric)–class fission power system (FPS). The technologies to be developed and validated by KRUSTY are extensible to space FPSs from 1 to 10 kW(electric), which can enable modular surface FPSs for human exploration as well as higher-power future potential deep space science missions. The KRUSTY demonstration is cofunded by NASA and the U.S. Department of Energy National Nuclear Security Administration. The KRUSTY demonstration in the National Critical Experiment Research Center’s Device Assembly Facility was completed in the first quarter of 2018.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Assessing Stainless Steel Compatibility in Flowing FLiBe Salt

To address the considerable interest in LiF-BeF 2 (FLiBe) compatibility for fission and fusion reactor applications, static and flowing compatibility experiments were conducted to assess the compatibility with type 316H stainless steel. In static testing at 550° and 650 °C, small mass changes were measured and posttest characterization of the FLiBe showed increased levels of Fe, Cr, Ni and Mn in the salt. Adding Be in the static salt test reduced the dissolution of Fe and Ni. Further, an initial assessment of mass transfer in flowing FLiBe without a Be addition was conducted using a monometallic 316H thermal convection loop (TCL) operated for 1000 h with a peak temperature of 650 °C. Similar to prior results in flowing FLiNaK salt, the 316H specimens exhibited small mass losses in the hot leg. Posttest characterization of the 316H specimens suggested Cr surface depletion in the hot and cold legs and possibly Fe deposition in the cold leg. To further understand this behavior, Cr and Fe dissolution was measured in static FLiBe at 550–650 °C.

316H stainless steel↗
DOE OSTI2022

Micro cavity fission chamber radiation detection system

A radiation detector to monitor the neutron flux of a nuclear reactor or other high-radiation environment, that can withstand the high temperatures and radiation fields of such environment, is provided. A small dielectric substrate with a low neutron-activation cross section is provided. The substrate is coated with a neutron conversion material, such as uranium oxide or thorium oxide. One or more substrates form a micro-sized detection cavity that is filled with a detection gas. A voltage is provided across anode and cathode wires in the detection cavity. A neutron absorbed in the conversion material may release reaction products into the gas, causing ionization of the gas which then produces a current or voltage signal. The small detector volume minimizes energy deposition into the detection gas by competing particles such as gamma rays, fast electrons, and beta particles, and therefore minimizes false counts while retaining large signals from neutron interactions.

McGregor, Douglas S.↗
DOE OSTI2020

Radiation Damage in Materials—Helium Effects

Despite its scarcity in terrestrial life, helium effects on microstructure evolution and thermo-mechanical properties can have a significant impact on the operation and lifetime of applications, including: advanced structural steels in fast fission reactors, plasma facing and structural materials in fusion devices, spallation neutron target designs, energetic alpha emissions in actinides, helium precipitation in tritium-containing materials, and nuclear waste materials. The small size of a helium atom combined with its near insolubility in almost every solid makes the helium–solid interaction extremely complex over multiple length and time scales. This Special Issue, “Radiation Damage in Materials—Helium Effects”, contains review articles and full-length papers on new irradiation material research activities and novel material ideas using experimental and/or modeling approaches. These studies elucidate the interactions of helium with various extreme environments and tailored nanostructures, as well as their impact on microstructural evolution and material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Micro-Tensile Properties of Irradiated AGR-2 TRISO Fuel Pyrolytic Carbon (PyC) and Silicon Carbide (SiC) Coatings

Tristructural isotropic (TRISO) coated nuclear fuel particles are emerging as a versatile option for new reactor designs, with the silicon carbide (SiC) layer crucial for retaining fission products. However, the mechanical properties of TRISO coating layers, particularly after irradiation, are not fully understood due to their small size and high radioactivity. Recent in situ micro-tensile testing of various TRISO layers aims to better understand the SiC layer's failure mechanisms, advancing TRISO fuel qualification. These micro-tensile results will be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Moly 99 Reactor Case Study

Molybdenum-99 (Moly 99) is a critical raw material for Technetium (Tc) 99m, a radioactive isotope most widely used in nuclear medicine procedures. Moly 99 has a short half-life of about six hours, which means it cannot be stockpiled. When Moly 99 decays, it turns into Tc 99m, which has a half-life of 214,000 years. The photon energy emitted from the decay of Moly 99 is used in a variety of nuclear imaging technologies such as gamma cameras. Furthermore, radiopharmaceutical manufacturers use the photon energy emitted from the decay of Moly 99 to produce generators for hospitals, clinics, and radiopharmacies. Once Moly 99 decays to Tc 99m, it is used to make individual patient doses for a variety of diagnostic imaging procedures. The Moly 99 Reactor Design is a conceptual blueprint for Moly 99 production that does not use weapon-grade uranium; instead, the reactor has a target core of low-enriched uranium. The reactor design is small, reaching a foot-and-a-half in height and diameter and consumes less than two megawatts of power. The reactor's only purpose is for medical isotope production and with every fission, Moly 99 is produced.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2020

Fission Accelerated Steady-state Testing (FAST)

In an effort to accelerate the irradiation time for advanced reactor fuels, a revised capsule design has been analyzed and developed for the Advanced Fuels Campaign (AFC). This design incorporates a highly enriched, reduced diameter fuel pin that is doubly encapsulated by two steel capsules. This design alloys accelerated irradiations and reduced sensitivity to fabrication variances and eccentricities. The capsule designs utilize existing experiment baskets from the AFC capsules in the Advanced Test Reactor (ATR) outer A position (FAST-OA) and the ATF-1 capsules in the small I position (FAST-SI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Complete β-decay patterns of 142 Cs, 142 Ba, and 142 La determined using total absorption spectroscopy

Background: The β decays of fission products produced in nuclear fuel are important for nuclear energy applications and fundamental science of reactor antineutrinos. In particular, nuclear reactor safety is related to the decay modes of radioactive neutron-rich nuclei, primarily via the emission of γ rays, neutrons, and electrons. Additionally nuclear reactors are the most powerful man-made source of antineutrinos emitted during the β decay of fission products. These antineutrinos are used to inspect fundamental properties of leptons as well as informing reactor operation. However, the majority of data on complex decays of fission products collected in the evaluated nuclear data repositories like Evaluated Nuclear Structure Data File (ENSDF) and Evaluated Nuclear Data Files (ENDF) are based on low-efficiency and often incomplete measurements resulting in questionable reference reactor antineutrino flux predictions, see the analysis by [Nichols, J. Nucl. Sci. Technol. 52, 17 (2015)]. Various assessments like the one done under the auspices of the [Yoshida et al., Assessment of Fission Product Decay Data for Decay Heat Calculations: A report by the Working Party on International Evaluation Co-operation of the Nuclear Energy Agency Nuclear Science Committee (Nuclear Energy Agency, Organization for Economic Co-operation and Development, Paris, France, 2007), Vol. 25], as well as by [Sonzogni, Johnson, and McCutchan, Phys. Rev. C 91, 011301(R) (2015)] and [Dwyer and Langford, Phys. Rev. Lett. 114, 012502 (2015)], list the A = 142 isobars with high cumulative fission yield among the important nuclei where data for reactor decay heat and/or antineutrino production should be verified and/or improved. Purpose: Here, our goal is to improve the quality of β -decay measurements and evaluate the impact of modified decay schemes on reactor decay heat and antineutrino energy spectra, for fission products along the A = 142 isobaric chain. This work is an in depth follow-up on [Rasco et al., Phys. Rev. Lett. 117, 092501 (2016)]. which presented briefly the impact of the corrected decay scheme of 142 Cs . Here, we extend the data to full isobaric decay chain including the daughter nuclei, 142 Ba and 142 La, and present more details on the 142 Cs results. Method: The decays of neutron-rich isobars of mass A = 142 produced by means of proton-induced fission of 238 U were measured using the Modular Total Absorption Spectrometer (MTAS) array on-line at the mass separator and Tandem accelerator at Oak Ridge National Laboratory. Results: The β -decay schemes for 142 Cs and 142 La were modified with respect to the nuclear data repositories. A small β-delayed neutron branching ratio for 142 Cs emitter was remeasured as $0.10^{+5}_{–3}% %. Improved precision on the measured half-lives is reported. Small corrections to the low-energy decay of 142 Ba are made. The β-decay patterns for 142 La and 142 Cs are presented. The decay heat release and cross section for the detection of reactor antineutrinos are deduced and compared to earlier results. Conclusions: The β-feeding pattern for 142 Cs having decay energy value $Q_β$ of over 7 MeV was substantially modified with respect to the current ENSDF entry. Smaller changes were encountered for 142 La, but since this A = 142 isobar also has a large cumulative yield in fission, the changes influence both decay heat and the antineutrino spectra. The previously known β intensities for 142 Ba decay ($Q_β$ value of 2.2 MeV) were verified and slightly modified. Overall, increased decay heat values and lower flux of antineutrinos interacting with matter are presented.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Investigating the AGN-201M research reactor's unique dominance ratio

The AGN-201M reactor is a small, thermal spectrum reactor located at the University of New Mexico (UNM). It is moderated by polyethylene, reflected by graphite, with fuel comprised of uranium microspheres embedded in polyethylene plates that are separated by an aluminum baffle. The dominance ratio of a multiplying system is the ratio of the first higher-mode eigenvalue to the fundamental, k{sub 1}/k{sub 0}. It is a key parameter in characterizing the rate of convergence, analyzing system stability, and determining how tightly coupled the system's neutron fission is. The purpose of this paper is to investigate the system's unusually low dominance ratio of 0.632. This investigation varied the reactor's physical parameters, such as the fuel geometry, fuel density, and reflector thickness, and examined their impact on the reactor's dominance ratio. Additionally, this study examined neutronically similar systems in hopes of identifying common causes for systems with low dominance ratios. The reason why the dominance ratio of the reactor is small compared to larger thermal reactors was determined to be because of its significantly smaller geometry and the composition of the fuel plates. The reflector's effect on the dominance ratio is small in comparison to the other factors, but was found to have a non-zero effect. Furthermore, the AGN-201M was found to have a significantly lower dominance ratio than systems in which it shares a very high (c{sub k} >95%) degree of neutronic similarity.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

BISON analyses of TRISO fuel performance, its dependence on time-at-temperature, and possible implications for fuel design and qualification

The Advanced Gas Reactor Fuel Development and Qualification (AGR) program has established a substantial technical foundation to support private entry into the U.S. high-temperature gas-cooled reactor market. However, emerging tristructural isotropic (TRISO)-fueled reactor applications include small modular reactors and microreactors with longer fuel residence times, which may expose fuels to higher time-at-temperature (TAT) values than were explored by the AGR program. Increased TAT could affect diffusive and thermomechanical behaviors such as Pd penetration, fission gas release, creep, and fission product transport. In this work, we applied multiscale best-estimate BISON fuel performance modeling to assess these effects within a representative design space based on the AGR-5/6/7 experiment and analyzed trends in predicted particle and compact fuel performance metrics with possible implications for near-term fuel design and qualification. BISON unambiguously predicted that TRISO fuel performance is sensitive to TAT. Increasing TAT was not predicted to increase the magnitude of failure-inducing tangential stresses in particle coating layers. Predictions obtained using a mechanistic model for Pd penetration indicated that penetration depth does not depend strongly on TAT. While these observations suggest that AGR testing provides a conservative upper bound for the steady-state operation of TRISO particles at lower powers and higher residence times, BISON also predicted that the release of poorly retained Ag would increase with TAT. Because these analyses applied models to extrapolate beyond the available experimental data, the authors recommend performing targeted experiments to confirm these predictions. Nevertheless, these predictions may provide reactor developers with enough confidence to make near-term design decisions associated with the potential fuel performance trade-offs of increasing TAT.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Materials for Small Nuclear Reactors and Micro Reactors, Including Space Reactors

Small nuclear reactors, including small modular reactors (SMRs) or reactors for space applications, rely on different materials than those typically applied in large-scale nuclear power plants. Examples include molten salts as cooling medium or fuel carrier, metal hydrides as high-temperature moderators, and fuels allowing for higher burnup. All of these also require novel structural materials, for which material interactions have to be understood. Fissionable and fissile materials, such as uranium or plutonium, are rarely considered in materials design other than for nuclear fuels. Similarly, the aspects of radiation damage, occurring during irradiation when a reactor operates, are unique to nuclear materials research. The handling of these materials puts further limitations on the materials science conducted for nuclear materials. All of these issues move research for these materials off the “main stream” of materials science, and cause it to be more easily conducted at national laboratories. However, nuclear reactors offer unique opportunities for carbon-neutral energy generation and have great potential to address if not solve problems arising from global warming. This special topic, sponsored by the TMS Nuclear Materials Committee, focuses on materials research for small nuclear reactors, both experimental and simulation/modeling.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Irradiation performance of nonfertile (Pu-MA-Zr) fast reactor metal fuels

This work was part of a program begun in 2001 to develop advanced nuclear fuels, originally as carriers for plutonium and minor actinides (neptunium, curium, and americium) taken from spent commercial light-water reactors (LWR) so that the plutonium and minor actinides could be ‘burned’ or transmuted in an accelerator or a fast nuclear reactor. A central part of these experiment programs has been the development of advanced fast reactor fuels, because a fast reactor was considered the most efficient vehicle to transmute the actinide waste products, and metallic fuels is a central focus of these tests. An experiment design was developed in which a thermal test reactor, the Advanced Test Reactor (ATR), was used to test small fuel pin prototypes, by creating areas in the core shielded by cadmium filters to produce a largely epithermal and fast neutron spectrum environment in which the pins could be irradiated. The results of non-fertile metallic fuel (no uranium) tests are presented here. Pu-Am-Np-Zr fuels were irradiated to fission densities up to 33 × 10 20 fission/cm 3 and Pu-239 depletions of up to 39%. The depletions were created by roughly 2/3 by fission and 1/3 by transmutation neutron capture. Up to five fuel ‘rodlets’ were irradiated in three sealed capsules stacked axially in the core, and the peak cladding temperatures ranged from 300°C to 500°C, depending on axial location as those near the core centerline are operating hotter and to higher fission densities. Several post-irradiation examinations (precision gamma scanning and fission gas release) were similar to other historical metal fuel experiments in fast reactors. However, optical metallography indicated that two of the rodlets had breached. The exact reasons are unclear. Due to the design of this irradiation experiment a rodlet breach could have increased the temperature in others in the same capsule by contaminating the thermal gap helium with heavier and less conductive fission product gases. Finally, some of those rodlets showed high amounts of fuel/cladding chemical interaction (FCCI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗