Search NASA⌕ Search

SEARCH · Search NASA

Results for “sodium dodecyl sulfate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Defect Repair of Polyelectrolyte Bilayers Using SDS: The Action of Micelles Versus Monomers

Defects within single, double, and triple polyelectrolyte bilayers derived from poly(sodium 4-styrenesulfonate) (PSS) and poly(diallyldimethyammonium chloride) (PDDA) have been repaired using aqueous solutions of sodium dodecyl sulfate (SDS), as evidenced by a reduction in their permeability and an increase in their permeation selectivity. In contrast to the use of monomer solutions of SDS, which were moderately effective in repairing only double and triple bilayers, micellar solutions proved highly effective for all three assemblies. Here, evidence for intact micelles or micellar fragments being deposited on the surface of single bilayers of PSS/PDDA has been obtained from a combination of atomic force microscopy, X-ray photoelectron spectroscopy, ellipsometry, and contact angle measurements. Observed CO 2 permeances of ca. 200 GPU and CO 2 /N 2 selectivities of ca. 30 for SDS-repaired, single bilayers of PSS/PDDA suggest that further development of such assemblies could have the practical potential for the separation of CO 2 from N 2 in the flue gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Improved CO 2 Capture Performance of Electrochemically Mediated Amine Regeneration Processes with Ionic Surfactant Additives

For the effective reduction of global CO 2 emissions, it is essential to develop and deploy efficient and cost-effective technologies for CO 2 capture, especially from large point sources. We recently developed an electrochemically mediated amine regeneration (EMAR) system to replace traditional thermal desorption for the capture of CO 2 from post-combustion flue gases. Despite EMAR effectiveness on a laboratory scale, concerns regarding the high gas-to-liquid ratio in the electrochemical cell and long-term instability of the electrodes need to be addressed before further scale-up of the process to a pilot plant and beyond can be entertained. Accordingly, we investigated the effect of using sodium dodecyl sulfate (SDS) as an anionic surfactant and dodecyltrimethylammonium bromide (DTAB) as a cationic surfactant on the process operation. It was found that it is advantageous to use an anionic surfactant for a system such as EMAR that contains hydrophilic electrodes and a positively charged electrochemically active species. The overall cell resistance was notably reduced when SDS anionic surfactant was used. The precipitation of copper particles observed in the anode outlet when no surfactant was used was effectively avoided when SDS was added to the electrolyte, resulting in electrode stability. In addition, smaller gas bubbles were produced in the presence of the SDS surfactant, which resulted in less blockage of the electrode by the gas with a resultant lower cell potential under constant current conditions, driving more efficient CO 2 desorption. This led to an ~25% reduction in the electrochemical energy requirement, the lowest ever achieved experimentally for the EMAR process. Altogether, the addition of a very low concentration of SDS resulted in the successful circumvention of the important problems faced by the EMAR system regarding further scale-up.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Studies on the "Aerobic" Acetyl-Coenzyme A Synthetase of Saccharomyces Cerevisiae: Purification, Crystallization, and Physical Properties of the Enzyme

A procedure for the purification of a stable acetyl-coenzyme A synthetase (ACS) from aerobic cells of Saccharomyces cerevisiae is presented. The steps include differential centrifugation, solubilization of the bound enzyme from the crude mitochondrial fraction, ammonium sulfate fractionation, crystallization to constant specific activity from ammonium sulfate solutions followed by Bio-Gel A-1.5 m column chromatography. The resulting enzyme preparation is homogeneous as judged by chromatography on Bio-Gel columns, QAE-Sephadex A-50 anion exchange columns, analytical ultracentrifugal studies, and polyacrylamide gel electrophoresis. Sedimentation velocity runs revealed a single symmetric peak with an s(sub (20,w)) value of 10.6. The molecular weight of the native enzyme, as determined by gel filtration and analytical ultracentrifugation, is 250,000 +/- 500. In polyacrylamide gel electrophoresis in the presence of sodium dodecyl sulfate, the molecular weight of the single polypeptide chain is 83,000 +/- 500. The purified enzyme is inhibited by palmityl-coenzyme A with a Hill interaction coefficient, n, of 2.88. These studies indicate that the ACS of aerobic Saccharomyces cerevisiae is composed of three subunits of identical or nearly identical size.

Satyanarayana, T.↗
DOE OSTI2024

A Pseudo‐Surfactant Chemical Permeation Enhancer to Treat Otitis Media via Sustained Transtympanic Delivery of Antibiotics

Abstract Chemical permeation enhancers (CPEs) represent a prevalent and safe strategy to enable noninvasive drug delivery across skin‐like biological barriers such as the tympanic membrane (TM). While most existing CPEs interact strongly with the lipid bilayers in the stratum corneum to create defects as diffusion paths, their interactions with the delivery system, such as polymers forming a hydrogel, can compromise gelation, formulation stability, and drug diffusion. To overcome this challenge, differing interactions between CPEs and the hydrogel system are explored, especially those with sodium dodecyl sulfate (SDS), an ionic surfactant and a common CPE, and those with methyl laurate (ML), a nonionic counterpart with a similar length alkyl chain. Notably, the use of ML effectively decouples permeation enhancement from gelation, enabling sustained delivery across TMs to treat acute otitis media (AOM), which is not possible with the use of SDS. Ciprofloxacin and ML are shown to form a pseudo‐surfactant that significantly boosts transtympanic permeation. The middle ear ciprofloxacin concentration is increased by 70‐fold in vivo in a chinchilla AOM model, yielding superior efficacy and biocompatibility than the previous highest‐performing formulation. Beyond improved efficacy and biocompatibility, this single‐CPE formulation significantly accelerates its progression toward clinical deployment.

Engineering↗
DOE OSTI2023

Mitigating the allergenicity of peanut allergen Ara h 1 by cold atmospheric pressure argon plasma jet

Abstract BACKGROUND Peanut allergy is recognized as a major food allergy that triggers severe and even fatal symptoms. Avoidance of peanuts in the diet is the main option for current safety management. Processing techniques reducing peanut allergenicity are required to develop other options. Cold plasma is currently considered as a novel non‐thermal approach to alter protein structure and has the potential to alleviate immunoreactivity of protein allergen. RESULTS The application of a cold argon plasma jet to peanut protein extract could reduce the amount of a 64 kDa protein band corresponding to a major peanut allergen Ara h 1 using sodium dodecyl sulfate–polyacrylamide gel electrophoresis, but the overall protein size distribution did not change significantly. A decrease in peanut protein solubility was a possible cause that led to the loss of protein content in the soluble fraction. Immunoblotting and enzyme‐linked immunosorbent assay elucidated that the immunoreactivity of Ara h 1 was significantly decreased with the time treated with plasma. Ara h 1 antigenicity reduced by 38% after five scans (approximately 3 min) of cold argon plasma jet treatment, and the reduction was up to 66% after approximately 15 min of treatment. CONCLUSION The results indicate that cold argon plasma jet treatment could be a suitable platform for alleviating the immunoreactivity of peanut protein. This work demonstrates an efficient, compact, and rapid platform for mitigating the allergenicity of peanuts, and shows great potential for the plasma platform as a non‐thermal technique in the food industry. © 2023 Society of Chemical Industry.

Hsu, Fu‐Chiun↗
DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis and characterization of porous polydimethylsiloxane structures with adjustable porosity and pore morphology using emulsion templating technique

Abstract Porous polydimethylsiloxane (PDMS) framework with adjustable pore structures has been fabricated by polymerization of the continuous phase in the emulsion templates. Different types of surfactants, including nonionic (Triton X‐100), cationic (Benzalkonium chloride), anionic (sodium dodecyl sulfate), and silicone‐based block copolymer were used to stabilize the water‐in‐oil emulsion system. Deionized water with a wide range of internal phases varying from 10% to 60% by weight was employed to make the low internal phase emulsion and medium internal phase emulsion. The effect of surfactant type, surfactant concentration, and the internal phase volume on the stability of the emulsion, pore morphology, and pore size distribution was explored. The stability of the emulsion was investigated by comparing the pore morphology of the cured sample at different set times, such as 0, 6, and 72 h. Scanning electron microscopy was employed for the characterization of the porous structures. The image analysis was conducted, and the pore size distribution, porosity, and open‐cell ratio of each sample were calculated. Interconnected pores have been seen in the porous PDMS made from emulsions with an internal phase larger than 30%. The results demonstrated that the frequency of open‐cell pores and the pore size is dependent on the surfactant types.

Abshirini, Mohammad↗
DOE OSTI2019

Cloning, Purification, and Characterization of Recombinant Thermostable β-Xylanase Tnap-0700 from Thermotoga naphthophila

The gene of a β-xylanase (Tnap-0700) was cloned from a hyperthermophilic Thermotoga naphthophila strain ATCC BAA-489 and expressed in Escherichia coli BL21 (DE3) via pET-21a (+) as an expression vector. The growth steps were upgraded for highest β-xylanase expression via several factors, for example, IPTG concentration, time of induction, pH, and temperature. The pH and temperature optima for the extreme expression of β-xylanase were 7.0 pH and 37 °C, correspondingly. Recombinant enzyme purified by heat treatment process, then later by immobilized metal ion affinity chromatography. Molecular mass of the purified β-xylanase was 38 kDa observed by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). The enzyme was stable at room temperature for 30 days. It exhibited high stability over wide series of temperature 50–90 °C and pH 4.0–9.0 upon the addition of 1 mM Ca{sup +2} and reduced in the existence of Cu{sup +2} and EDTA. The addition of about 10–30% different organic solvents have no considerable effect on enzyme. However, SDSF and urea acting as an inhibitor leads to decrease in the enzyme activity. The β-xylanase enzyme was active to hydrolyze xylan from beechwood forming xylose. Thermostable β-xylanase causes the breakdown of complex carbohydrates into monosaccharide components. This thermostable β-xylanase revealed remarkable properties, which make it an encouraging candidate for various industrial applications especially in the alteration of renewable biomaterials into ethanol production, and biofuels from lignocellulosics has acknowledged much devotion subsequently in the last decade.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Effect of surfactant assisted ultrasonic pretreatment on production of volatile fatty acids from mixed food waste

In this study, the potential effect of surfactant assisted ultrasonic pretreatment on mixed food waste was investigated. Surfactants, such as Rhamnolipid, Sodium dodecyl sulfate; Glucopon and Triton X 100 were evaluated in this work. Among them, the maximum solubilization of chemical oxygen demand of 45.5 % and the highest release of soluble COD of 31 g/L were observed for ultrasonication assisted by Triton X 100 at a dose of 0.01 g/g TS in 30 min. The presence of a surfactant also reduced 27.5 % of energy demand when compared to ultrasonic pretreatment alone. Compared to the non-pretreated samples after anaerobic digestion, ultrasonication assisted by Triton X 100 led to 95 % increase of volatile fatty acid titers and 83 % increase of carbon conversion efficiency. Furthermore, sonication with the addition of Triton X 100 was proven to be highly effective toward increasing digestibility of and yield of volatile fatty acid from mixed food waste.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Effect of particle size on the capture of uranium oxide colloidal particles from aqueous suspensions via high-gradient magnetic filtration

The effectiveness of High Gradient Magnetic Filtration (HGMF) in capturing uranium oxide particles from suspensions was investigated in this study. Two sets of experiments were performed to evaluate the importance of size on the capture of uranium oxide particles. The first considered two batches sieved into size bins of< 5, 5–10, 10–15, and 15–20 µm, while the second was performed using two suspensions with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm. Iron oxide experiments, with particles between 0.3 and 0.8 µm, were performed for calibration purposes. In all experiments, a surfactant (Triton-X100 or sodium dodecyl sulfate) was used to prevent particle aggregation and limit the influence of non-magnetic capture mechanisms. A magnetic field of approximately 1.1 Tesla was generated using a water cooled electromagnet. HGMF was performed using tubular filters packed with ferromagnetic stainless-steel wool. Of the initial four uranium oxide particle sizes, magnetic capture was only observed for particles with a diameter of less than 5 µm, while larger particles experienced no magnetic and minimal total capture. For particles with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm, capture efficiencies increased by 39 ± 9% and 34 ± 6% respectively, solely due to the magnetic field. Although the magnetic force is proportional to particle diameter, the capture efficiency decreased as diameter increased. So these results suggest that Brownian diffusion, which is influential for micron sized particles and increases with decreasing particle size, is acting in conjunction with the magnetic force to influence the efficacy of HGMF for uranium oxide. This important finding underscores the effectiveness of Brownian diffusion in increasing the rate of collision between particles and collector fibers. A stochastic trajectory model was developed to incorporate the influence of Brownian motion on particle behavior and filter removal efficiency. Modeling results are discussed and compared for uranium and iron oxide particles.

42 ENGINEERING↗
DOE OSTI2025

Characterizing the pore-scale impacts of enhanced-solubilization solutions on organic-liquid morphology and fluid-fluid interfacial area with microtomography

Synchrotron X-ray microtomography was used to directly quantify the impact of enhanced-solubilization solutions on mobilization of a non-wetting fluid in a natural porous medium. Polyoxyethylene sorbitan monooleate (tween 80), hydroxypropyl-β-cyclodextrin (HPCD), sodium dodecyl sulfate (SDS), and ethanol were used as the solubilization reagents. Tetrachloroethene (PCE) was used as the entrapped organic immiscible liquid. Microtomography images were collected prior to and after successive floods with each reagent solution. The total trapping number was varied by more than three orders of magnitude by changing the velocity and viscosity of the aqueous phase as well as the interfacial tension between fluid phases. The results were compared to those obtained from equivalent experiments conducted with water flooding. Inspection of images indicated that mobilization caused a change in PCE morphology and distribution for all reagents with the exception of HPCD, for which a lower trapping number was determined compared to the other experiments. Mobilization of organic liquid was observed at total trapping numbers that were consistent with prior work. The enhanced-solubilization solutions had minimal impact on the configuration or magnitude of fluid-fluid interfacial area.

Interfacial area↗
DOE OSTI2025

Development of carbon nanosensor for vinpocetine at zinc oxide modified carbon matrix with anionic surfactant for clinical application

A nano-level sensing method was formulated for the trace-level detection and determination of vinpocetine (VIN) at a zinc oxide nanomaterial-based carbon matrix with immobilised anionic surfactant sodium dodecyl sulfate (ZnO-SDS/CPE) using cyclic voltammetry (CV) and square wave voltammetry (SWV) approaches. The catalytic properties of ZnO impact the electron rate of VIN activity, resulting in a threefold increase in the VIN peak response with the ZnO-SDS-modified sensor. Here, the effects of several factors, including scan rate, pH, accumulation length, modifier amount, and concentration, were investigated on the VIN peak current. The electro-oxidation of VIN by pH study involves one proton and one electron. The CV method also investigated the effect of scan rate. The charge transfer coefficient (α) is obtained to be 0.58, and the heterogeneous rate constant (k°) is estimated to be 4.46 s⁻¹. The concentration effect of VIN was studied using the SWV method. Specifically, the SWV methodology achieved the lowest detection limit compared to previously published approaches, with estimated values of the Limit of Detection (LOD) and Limit of Quantification (LOQ) being 2.2 × 10⁻⁸ M and 7.7 × 10⁻⁸ M, respectively. The trace level of VIN in tablet and urine samples was determined using the modified sensor. Moreover, the sensor demonstrates particular reproducibility and long-term stability, making it suitable for real-time applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Zeta potential measurements of SiO 2 and TiO 2 particles in anionic and cationic surfactant solutions

Zeta potential measurements can provide valuable insights into colloidal stability and may reflect changes in the electrochemical double layer that influence electrocatalysis. In this study, we used zeta potential measurements to monitor and investigate the adsorption behavior of anionic sodium dodecyl sulfate (SDS), cationic dodecyl trimethyl ammonium bromide (DTAB), and cationic cetyl trimethyl ammonium bromide (CTAB) surfactants on SiO 2 and TiO 2 particles in DI water. The zeta potentials of SiO 2 and TiO 2 particles were measured as a function of particle concentration in 1.0 mM, 5.0 mM, and 10.0 mM surfactant solutions. Results indicate that there is no significant adsorption of DS - ions on SiO 2 particles across all SDS concentrations investigated in this study. The zeta potential of TiO 2 particles shifts from negative to positive as particle concentration increases at 1.0 mM SDS, indicating a decrease in DS - ions adsorption per TiO 2 particle. Adsorption plateaus at 5.0 mM SDS for all TiO 2 concentrations studied. In contrast, DTA + and CTA + ions showed clear adsorption on SiO 2 particles, but DTA + exhibited no apparent adsorption on TiO 2 particles. Interestingly, CTA + adsorption on TiO 2 was only evident at higher surfactant concentrations. This study presents a systematic investigation of zeta potential behavior as a function of particle and surfactant concentration, highlighting adsorption saturation and electrostatic reversal. Unlike prior work that was limited to single particle concentration measurements, our approach reveals how surfactant adsorption per particle decreases with increasing surface area. Despite the structural similarity between DTAB and CTAB, this study captured the different adsorption behaviors of both surfactants on SiO 2 and TiO 2 , emphasizing the role of the overall structure of the surfactant on surfactant adsorption behavior. These insights refine the interpretation of zeta potential data and advance understanding of surfactant adsorption on oxide particles. The insight provided in this study about surfactant adsorption on SiO 2 and TiO 2 particles could have important implications for the design of more effective colloidal and catalytic systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Data-Driven Discovery of Linear Molecular Probes with Optimal Selective Affinity for PFAS in Water

Approaches to tackle the wide and growing variety of highly persistent per- and polyfluoroalkyl substances (PFAS) are of pressing global need because of their detrimental human health effects, such as cancer, birth defects, and hormone imbalance. Sensitive, selective, and easy-to-use real-time sensors to monitor and detect PFAS and sorbents to extract them are critical to meeting government-mandated environmental concentrations. In this work, we combine all-atom molecular dynamics simulations, enhanced sampling, deep representational learning, and Bayesian optimization to perform high-throughput virtual screening for highly sensitive and selective molecular probes. Our molecular design space consists of 3850 linear hydrocarbon chains with varying degrees of halogenation with and without amine- and phosphine-based headgroups. By employing a data-driven search process, we efficiently explore the molecular design space to optimize the sensitivity to perfluorooctanesulfonic acid (PFOS) as a prototypical PFAS analyte and selectivity relative to a sodium dodecyl sulfate (SDS) interferent. We calculate 504 Gibbs free energies of probe-analyte and probe-interferent interactions and identify probes with PFOS association free energies of up to (-ΔG PFOS ) = 9.8 ± 0.2 kJ/mol and selectivities relative to SDS of (-ΔΔG PFOS–SDS ) = 3.1 ± 1.5 kJ/mol. A C 11 Br 23 P(CH 3 ) 2 probe containing 11 backbone brominated carbons and a tertiary phosphine headgroup possesses the most sensitive binding constant to PFOS within the defined search space of K b PFOS = 177.4 ± 12.7, and a semibrominated probe C 5 H 11 C 7 Br 14 N(CH 3 ) 2 containing 12 backbone carbons and a tertiary amine headgroup possesses the highest selectivity relative to SDS of K b PFOS /K b SDS = 4.6 ± 1.7. A retrospective analysis of our data to extract interpretable design rules reveals that the sensitivity of linear hydrogenated probes increases by approximately 1 kJ/mol per C–C bond. The addition or removal of halogen atoms and amine or phosphine headgroups produces nonmonotonic changes in both sensitivity and selectivity with changes to the sensitivity of up to 2.5 kJ/mol. Finally, this work places empirical limitations on the performance of a wide range of linear probes for PFOS detection and offers a generic strategy for high-throughput computational screening to promote selective and sensitive binding.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Revealing the Influence of Salts on the Hydration Structure of Ionic SDS Micelles by Contrast-Variation Small-Angle Neutron Scattering

The influence of lithium chloride (LiCl) on the hydration structure of anionic micelles of sodium dodecyl sulfate (SDS) in water was studied using the contrast-variation small-angle neutron scattering (SANS) technique. In the past, extensive computational studies have shown that the distribution of invasive water plays a critical role in the self-organization of SDS molecules and the stability of the assemblies. However, in past scattering studies the degree of the hydration level was not examined explicitly. Here, a series of contrast-variation SANS data was analyzed to extract the intramicellar radial distributions of invasive water and SDS molecules from the evolving spectral lineshapes caused by the varying isotopic ratios of water. By addressing the intramicellar inhomogeneous distributions of water and SDS molecules, a detailed description of how the counterion association influences the micellization behavior of SDS molecules is provided. The extension of our method can be used to provide an in-depth insight into the micellization phenomenon, which is commonly found in many soft matter systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Assessing Structural, Thermal, and Functional Characteristics of Marigold Flower Protein as a Sustainable Food Ingredient

The demand for sustainable and alternative protein sources has been on the rise, driving interest in the valorization of underutilized plants. This study evaluated Calendula officinalis (marigold), a common floral waste, as a sustainable alternative protein source for the food industry. The primary objective of this study was to investigate the physicochemical properties of protein fractions from Calendula officinalis flower to evaluate their potential as a novel protein ingredient. Extraction of the Calendula officinalis flower yielded 92.17% of the crude protein. A sequential extraction of albumin, globulin, glutelin, and prolamin from marigold flower revealed albumin as the dominant fraction (65.47%) and exhibited the highest protein functionality, including water-holding capacity (2.37 g/g), oil-holding capacity (2.49 g/g), and emulsifying capacity (65.22 mL/g). Compared with other protein fractions, glutelin showed a relatively high emulsifying and foaming capacity (EC: 59.13 mL/g; FC: 16.23%). Differential scanning calorimetry revealed high thermal stability for albumin (T p = 105.28 °C) and glutelin (T p = 97.6 °C). Sodium Dodecyl Sulfate–Polyacrylamide Gel Electrophoresis (SDS-PAGE) and Liquid Chromatography–Mass Spectrometry (LC-MS) confirmed the presence of abundant low-molecular-weight polypeptides (<37 kDa), which enhanced emulsification, while scanning electron microscopy revealed porous structures aligned with hydration properties. Antioxidant activity was higher in albumin and glutelin, linked to surface hydrophobicity. LC-MS/MS identified 33 short-chain proteins, including oxidoreductase proteins and lipid-transfer proteins. Findings highlight marigold flower proteins as a sustainable, functional ingredient for a diverse range of food applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Surfactant Engineering and Its Role in Determining the Performance of Nanoparticulate Organic Photovoltaic Devices

The fabrication of organic photovoltaics (OPVs) from non-hazardous nanoparticulate (NP) inks offers considerable promise for the development of ecofriendly large-scale printed solar modules. However, the typical NP core-shell morphology (driven by the different donor/acceptor affinities for the surfactant used in NP synthesis) currently hinders the photovoltaic performance. As such, surfactant engineering offers an elegant approach to synthesizing a more optimal intermixed NP morphology and hence an improved photovoltaic performance. In this work, the morphology of conventional sodium dodecyl sulfate (SDS) and 2-(3-thienyl) ethyloxybutylsulfonate (TEBS)-stabilized poly(3-hexylthiophene) (P3HT) donor:phenyl-C 61 -butyric acid methyl ester (PC 61 BM) acceptor NPs is probed using scanning transmission X-ray microscopy, UV-vis spectroscopy, grazing-incidence X-ray diffraction, and scanning electron microscopy. While the SDS-stabilized NPs exhibit a size-independent core-shell morphology, this work reveals that TEBS-stabilized NPs deliver an intermixed morphology, the extent of which depends on the particle size. Consequently, by optimizing the TEBS-stabilized NP size and distribution, NP-OPV devices with a power conversion efficiency that is ~50% higher on average than that of the corresponding SDS-based NP-OPV devices are produced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrospun porous La–Sr–Co–Ni–O nanofibers for highly sensitive non-enzymatic glucose detection

Glucose biosensors are widely used for clinical, industrial, and environmental applications. Nonenzymatic electrochemical glucose biosensors based on metal oxides with a perovskite structure have exhibited high sensitivity, excellent stability, and cost efficiency. In this work, porous La–Sr–Co–Ni–O (LSCNO) nanofibers, with an ABO 3 -type perovskite structure, were prepared through optimizing the A-site and B-site elements by electrospinning, followed with calcination at 700 °C for 5 h. Characterized by scanning and transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy, fabricated nanofibers were confirmed to be porous and nanosized polycrystalline grains with high crystallinity. A novel La 0.75 Sr 0.25 Co 0.5 Ni 0.5 O 3 -based nonenzymatic electrochemical biosensor was developed, which is sensitive to glucose because of an electrochemically catalytic mechanism, a mediated electron transfer involving Ni(II)/Ni(III) or Co(II)/Co(III), accompanying with gluconic acid complexation. The glucose biosensor presented a linear response in the range of 0.1–1.0 mM with a calibration sensitivity of 924 ± 28 μA mM –1 , a proportion of the variance of 0.9926, and a lower limit of detection of 0.083 mM, respectively, demonstrating an outstanding analytical performance. The biosensor showed no response to the most widely used anionic surfactant, sodium dodecyl sulfate, and low sensitivity to other biomolecules, such as fructose, lactose, galactose, mannose, dopamine, and ascorbic acid. A urine sample was tested by this novel nonenzymatic electrochemical biosensor by standard addition method, suggesting a potential application for clinical test.

36 MATERIALS SCIENCE↗