Search NASA⌕ Search

SEARCH · Search NASA

Results for “subassembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Process for thermal imaging scanning of a swaged heater for an anode subassembly of a hollow cathode assembly

A process for thermal imaging scanning of a swaged heater of an anode subassembly of a hollow cathode assembly, comprising scanning a swaged heater with a thermal imaging radiometer to measure a temperature distribution of the heater; raising the current in a power supply to increase the temperature of the swaged heater; and measuring the swaged heater temperature using the radiometer, whereupon the temperature distribution along the length of the heater shall be less than plus or minus 5 degrees C.

Patterson, Michael J.↗
NASA NTRS2009

System Modeling of Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly for Prototype Design

This paper describes modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly: the sorbent bed, a sublimation (cooling) heat exchanger (SHX), and a condensing icing (warming) heat exchanger (CIHX). The primary function of the MTSA, removing carbon dioxide from a ventilation loop, is performed via the sorbent bed. The CIHX is used to heat the sorbent bed for desorption and to remove moisture from the ventilation loop while the SHX is alternately employed to cool the sorbent bed via sublimation of a spray of water at low pressure to prepare the reconditioned bed for the next cycle. This paper describes a system level model of the MTSA as developed in Thermal Desktop and SINDA/FLUINT including assumptions on geometry and physical phenomena, modeling methodology and relevant pa ra mete rizatio ns. Several areas of particular modeling interest are discussed. In the sorbent bed, capture of the translating CO2 saturation front and associated local energy and mass balance in both adsorbing and desorbing modes is covered. The CIHX poses particular challenges for modeling in SINDA/FLUINT as accounting for solids states in fluid submodels are not a native capability. Methods for capturing phase change and latent heat of ice as well as the transport properties across a layer of low density accreted frost are developed. This extended modeling capacity is applicable to temperatures greater than 258 K. To extend applicability to the minimum device temperature of 235 K, a method for a mapped transformation of temperatures from below the limit temperatures to some value above is given along with descriptions for associated material property transformations and the resulting impacts to total heat and mass transfer. Similar considerations are shown for the SHX along with assumptions for flow mechanics and resulting model methods for sublimation in a flow.

Bower, Chad↗
DOE OSTI2020

IHE Material and IHE Subassembly Qualification Test Description and Criteria (v. 14.7)

The purpose of the deflagration-to-detonation test is to demonstrate that an IHE material will not undergo deflagration-to-detonation transition (DDT) under stockpile relevant conditions of scale, confinement, and material condition. Inherent in this test design is the assumption that ignition does occur, with onset of deflagration. The test design will incorporate large margins and replicates to account for the stochastic nature of DDT events.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Double sided measurements and associated error bars for planar samples or subassemblies

Many of the high energy density (HED) experiments use targets with planar components usually in a multilayer stack as the physics package which is at the heart of the experiment. The physics package contains the sample part under study as well as other components as shown in Fig. 1, that when exposed to the laser drive applies pressure onto or shock the main component to take it to the desired state in the phase diagram. These other components may include the ablator, pusher, x-ray pre-heat shield, window or other special components. The components are usually glued together. Currently, experiments on NIF and Omega in the Dynamic Materials campaign use several platforms such as Diffraction, EOS and Strength (Ref 1-3) which all use such planar stack physics packages.

42 ENGINEERING↗
NASA NTRS1980

Secondary mirror subassembly in the 2.4 m NASA optical telescope

The secondary mirror is a circular disc provided with a shoulder. Three clamps located 120 deg apart support the mirror shoulder. On one side of the mirror shoulder, a coated graphite-epoxy ring connects the three clamps. Three axial flexures with a low radial compliance extend out from a support platform constructed of coated graphite-epoxy box structs and invar corners, and provide a nominal in-plane zero coefficient of thermal expansion. In each invar corner piece, a ball joint provides a connection to a expansion. In each invar corner piece, a ball joint provides a connection to a six-degree-of-freedom adjustment system that can move the secondary mirror with a high degree of precision in defocus, decenter, and tilt. Thermal controls that maintain structural-element temperature variations within specified limits insure that the assembly exceeds stability and figure control requirements on the secondary mirror.

Ahmed, N.↗
NASA NTRS1993

A comparison of refined models for flexible subassemblies

Interactions between structure response and control of large flexible space systems have challenged current modeling techniques and have prompted development of new techniques for model improvement. Due to the geometric complexity of envisioned large flexible space structures, finite element models (FEM's) will be used to predict the dynamic characteristics of structural components. It is widely accepted that these models must be experimentally 'validated' before their acceptance as the basis for final design analysis. However, predictions of modal properties (natural frequencies, mode shapes, and damping ratios) are often in error when compared to those obtained from Experimental Modal Analysis (EMA). Recent research efforts have resulted in the development of algorithmic approaches for model improvement, also referred to as system or structure identification.

Smith, Suzanne Weaver↗
DOE OSTI2021

Vacuum manufacture of cryogenic pressure vessels for hydrogen storage

In one aspect the present disclosure relates to a method of manufacturing a cryogenic pressure vessel. The method may include providing a metal lined, composite wrapped vessel which has a boss. The method may further include securing an inlet to the boss, and then encapsulating the metal lined, composite wrapped vessel within a metallic layer in a vacuum controlled environment to form an encapsulated inner tank subassembly. The method may further include securing at least one support to an exterior of the encapsulated inner tank subassembly, and within the controlled vacuum environment, applying a metal coating over the encapsulated inner tank subassembly and the at least one support to form a metal coated, encapsulated inner tank subassembly. The method may further include, within the controlled vacuum environment, encapsulating the metal coated, encapsulated inner tank subassembly within a metallic vacuum jacket, which forms the cryogenic pressure vessel.

Aceves, Salvador M.↗
NASA NTRS1976

Fifth wheel

An improved fifth wheel for a tractor trailer rig, characterized by a first subassembly including a wear plate was developed and modified to be mounted on a downwardly facing surface of a trailer. A king pin projected normally therefrom, and a second subassembly is adapted to be pivotally mounted on an upwardly facing surface of a tractor. The king pin is brought into contiguous relation with the first sub assembly. A receiver for capturing the king pin is included along with a safety means responsive to a failure of the king pin or its latching mechanism for joining the first subassembly with the second subassembly.

Albrecht, W. P.↗
NASA NTRS1991

Expert systems for assembly sequence evaluation

The objective is to identify delivered orbital subassemblies derived from a phase A conceptual space vehicle design while minimizing on-orbit assembly complexity. The topics covered are presented in viewgraph form and include the following: an orbital assembly scenario; subassemblies; subassembly identification and simulation model; estimating subassembly interfaces by engineering functional allocation using MBR; representative data base of interface connections; vehicle decomposition model; connection interface estimation model results; knowledge-source 1 and 2 results; knowledge-source 3 -- connection-index results (Boeing NTR-2016 CI-profile); KS3 algorithm, and KS3 flight manifest results.

Jolly, Steve↗
NASA NTRS1998

Misalignment Accommodating Connector Assembly

Misalignment accommodating connector assembly for removably connecting first and second objects which may comprise: a first connector subassembly having an arm member extending therefrom transversely through which is provided a tubular member; a second connector subassembly having a pair of spaced apart arm members each of which is provided with a transversely disposed coaxially aligned semi-cylindrical recess for receiving opposite ends of the first connector tubular member upon lateral insertion of the first connector arm member into the space between the second connector pair of arm members. An axially extendable and contractible fastener subassembly carried by the first connector tubular member is extendable to allow insertion or removal of the first connector arm member into or from the space between the second connector pair of arm members and contractible when the opposite ends of the tubular member are substantially received by the semi-cylindrical recesses of the pair of spaced apart arm members to lock the first and second connector subassemblies together.

Stemper, Jack S.↗
DOE OSTI2024

System and method for geometrically constrained axisymmetric adjustable kinematic mount

The present disclosure relates to an adjustable mount apparatus. The apparatus may have a material support having a plurality of support legs, with each one of the support legs having a distal portion. A base assembly is used which has a plurality of laterally extending leg portions. A plurality of adjustably positionable capture subassemblies are slidably disposed within the laterally extending leg portions for releasably coupling to the distal portions of the support legs to hold the material support in a stable manner on the base assembly. A plurality of moveable elements, each being independently associated with one of the capture subassemblies, enable highly controlled linear movement of the capture subassemblies. Each capture subassembly engages with the distal portion of one of the support legs to exert a clamping force thereon, to affix the material support securely to the base assembly.

Guzorek, Steven J.↗
NASA NTRS2004

Mid-frequency Band Dynamics of Large Space Structures

High and low intensity dynamic environments experienced by a spacecraft during launch and on-orbit operations, respectively, induce structural loads and motions, which are difficult to reliably predict. Structural dynamics in low- and mid-frequency bands are sensitive to component interface uncertainty and non-linearity as evidenced in laboratory testing and flight operations. Analytical tools for prediction of linear system response are not necessarily adequate for reliable prediction of mid-frequency band dynamics and analysis of measured laboratory and flight data. A new MATLAB toolbox, designed to address the key challenges of mid-frequency band dynamics, is introduced in this paper. Finite-element models of major subassemblies are defined following rational frequency-wavelength guidelines. For computational efficiency, these subassemblies are described as linear, component mode models. The complete structural system model is composed of component mode subassemblies and linear or non-linear joint descriptions. Computation and display of structural dynamic responses are accomplished employing well-established, stable numerical methods, modern signal processing procedures and descriptive graphical tools. Parametric sensitivity and Monte-Carlo based system identification tools are used to reconcile models with experimental data and investigate the effects of uncertainties. Models and dynamic responses are exported for employment in applications, such as detailed structural integrity and mechanical-optical-control performance analyses.

dynamics↗
NASA NTRS1972

Real-time Optical Alignment and Diagnostic System (ROADS)

The ultimate and most frequent usage of ROADS will be the alignment of subassemblies (collector and collimator) prior to their installation in a chamber. The system as designed has inherent associated capabilities well applied to acceptance testing of the No. 4 mirror, prediction of in-chamber performance, generation of a catalog of test results and other data, providing data for the plotting of isointensity lines, and other applications which are discussed. The ROADS system will collect, process, display, analyze, and retain data as required for components, partial subassemblies, complete subassemblies, complete modules, and multimodular arrays.

Source record↗
NASA NTRS1973

Application of composites to helicopter airframe and landing gear structures

A preliminary design study has indicated that advanced composite helicopter airframe structures can provide significant system cost advantages in the 1980's. A seven percent increase in productivity and a five percent reduction in life cycle cost are projected. Due to their complexity, landing gear structures do not substantially benefit from the use of advanced composites. The most successful concept was found to be all-molded composite modular panels, which provide integral skin/stringer and frame subassemblies. These subassemblies significantly reduce the number of parts relative to present construction. The subassemblies are mechanically jointed together for economical, rapid final assembly and permit field replacement in the event of major damage.

Rich, M. J.↗