Search NASA⌕ Search

SEARCH · Search NASA

Results for “suction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Experimental study of supersonic laminar base flow with and without suction

Heat-transfer and pressure distributions in laminar separated flows downstream of rearward-facing steps with and without mass suction were investigated at Mach numbers around 4 for the conditions when the boundary-layer thickness was comparable to or larger than the step height. In both suction and no-suction cases, an increase of the step height resulted in a sharp drop of the base heating rates, which then gradually recovered to less than or near attached-flow values obtained with flat-plate configuration. Mass suction from the step base area increased the local heating rates; this effect, however, was relatively weak for laminar flows tested, and the competing effect of the step height clearly predominated. It was found that even removal of the entire incoming boundary layer was not sufficient to raise the poststep heating rates above the flat-plate values. The base pressure in the no-suction, solid-step case correlated reasonably well with the step height-to-boundary-layer thickness ratio and with the Reynolds number based on the step height.

Jakubowski, A. K.↗
NASA NTRS1977

Performance of high-area-ratio annular dump diffuser using suction-stabilized-vortex flow control

A short annular dump diffuser having a geometry conductive to formation of suction stabilized toroidal vortices in the region of abrupt area change was tested. The overall diffuser area ratio was 4.0 and the length to inlet height ratio was 2.0. Performance data were obtained at near ambient temperature and pressure for inlet Mach numbers of 0.18 and 0.30 with suction rates ranging from 0 to 18 percent of total inlet mass flowrate. Results show that the exit velocity profile could be readily biased toward either wall by adjustment of inner and outer wall suction rates. Symmetric exit velocity profiles were inherently unstable with a tendency to revert to a hub or tip bias. Diffuser effectiveness was increased from about 38 percent without suction to over 85 percent at a total suction rate of 10 to 12 percent. At the same time diffuser total pressure loss was reduced from 3.1 percent to 1.1 percent at an inlet Mach number of 0.3.

Juhasz, A. J.↗
NASA NTRS1978

Performance characteristics of two annular dump diffusers using suction-stabilized vortex flow control

Test results are described for two abrupt area change annular diffusers with provisions for maintaining suction stabilized toroidal vortices at the area discontinuity. Both diffusers had an overall area ratio of 4.0 with the prediffuser area ratio being 1.18 for diffuser A and 1.4 for diffuser B. Performance was evaluated at near atmospheric pressure and temperature for a range of inlet Mach numbers from 0.18 to 0.41 and suction rates from 0 to 18%. Static pressure recovery improved significantly as the suction rate was increased to approximately 11%. Results obtained with diffuser A were superior to that obtained with diffuser B. Flat radial profiles of exit velocity were not obtained since the flow showed preferential hub or tip attachment at moderate suction rates. At high suction rates the diffuser exit flow became circumferentially nonuniform and unstable.

Juhasz, A. J.↗
NASA NTRS1979

Experiments on tandem diffusers with boundary-layer suction applied in between

Experiments were performed on conical diffusers of various configurations with the same, but rather unusually large, 16:1 area ratio. Because available performance data on diffusers fall short of very large area ratio configurations, an unconventional design, consisting of two diffusers following each other in tandem, was proposed. Both diffusers had the same area ratio of 4:1, but had different taper angles. While for the first diffuser (called leading) the angle remained constant, for the second (called follower), the taper angle was stepped up to higher values. Boundary layer control, by way of suction, was applied between the diffusers, and a single slot suction ring was inserted between them. The leading diffuser had an enclosed nominal divergence angle 2 theta = 5 degrees, while the follower diffusers had either 10, 20, 30, or 40 degrees, respectively, giving 4 combinations. The experiments were performed at four different Reynolds numbers with various suction rates. The rates indicate a general improvement in the performance of all diffusers with boundary layer suction. It appears that the improvement of the pressure recovery depends on both the Reynolds number and the suction rate, and the largest increase, 0.075, was found at the lowest R sub e when the follower divergence was 2 theta = 40 degrees.

Barna, P. S.↗
NASA NTRS1980

On the stabilization of three-dimensional boundary layers by suction and cooling

A significant reduction in the drag of transonic aircraft can be achieved by using an active method of boundary-layer control to maintain laminar flow on the aerodynamic surfaces. The stabilizing influence of suction for both favorable and adverse pressure gradients is demonstrated by means of the self-similar incompressible three-dimensional boundary layers on yawed wedges. Profile instability is measured by the maximum amplification rate of fixed-frequency disturbances computed according to linearized, locally parallel, spatial stability theory. Suction is found to be more effective in controlling Tollmien-Schlichting instability than stationary cross-flow disturbances. The effectiveness of surface cooling as a method of stabilization is compared with suction for the boundary layers on a transonic 35 deg swept wing of infinite span. It is found from compressible stability theory that when the surface is cooled to a uniform temperature such that the maximum cross-flow velocity is reduced by the same amount as with a uniform suction distribution, the stabilizing effect of cooling on cross-flow disturbances is less than with suction.

Mack, L. M.↗
NASA NTRS1981

Compressible boundary-layer stability calculations for sweptback wings with suction

The stability of the laminar boundary layers on two transonic wings of infinite span with distributed suction is investigated with the compressible, parallel-flow stability theory. Both wings have supercritical airfoil sections; one has a sweep angle of 23 deg, the other of 35 deg. Zero-frequency disturbances are used to represent cross-flow instability, and disturbances with the wavenumber vector aligned with the local flow direction represent traveling-wave instability. In both cases, the maximum spatial amplification rate is used as a measure of the instability. For the suction, distributions with constant mass flux downstream of the starting point are used. The main objective is to determine how the maximum amplification rate varies with the magnitude and starting point of the suction. It is found for both types of disturbances that the maximum amplification rate varies almost linearly with the suction magnitude up to at least the point where the amplification rate is halved. Different starting locations for the suction in the first 4% of the chord were found to affect cross-flow instability, but to have little influence on traveling-wave instability.

Mack, L. M.↗
NASA NTRS1982

Stability of boundary layers with porous suction strips: Experiment and theory

Low turbulence tunnel experiments on the stability and transition of 2 D boundary layers on flat plates with and without suction are described. A number of general suction cases are discussed. Test results showed that the maximum stabilization occurred when the suction was moved toward the Branch I neutral point. An analytical study of the stability of two dimensional, incompressible boundary layer flows over plates with suction through porous strips was performed. The mean flow was calculated using linearized triple deck, closed form solutions. The stability results of the triple deck theory are shown to be in good agreement with those of the interacting boundary layers. An analytical optimization scheme for the suction configuration was developd. Numerical calculations were performed corresponding to the experimental configurations. In each case, the theory correctly predicts the experimental results.

Reynolds, G. A.↗
NASA NTRS1982

Vortex lift augmentation by suction on a 60 deg swept Gothic wing

An experimental investigation was conducted in the Langley high-speed 7- by 10-foot wind tunnel to determine the aerodynamic performance of suction applied near the wing tips above the trailing edge of a 60 deg swept Gothic wing. Moveable suction inlets were symmetrically mounted in the proximity of the trailing edge, and the amount of suction was varied to maximize wing lift. Tests were conducted at Mach 0.15, 0.30, and 0.45, and the angle of attack was varied from -4 to 50 deg. The suction augmentation increases the lift coefficient over the entire range of angle of attack. The lift improvement exceeds the unaugmented wing lift by over 20%. Moreover, the augmented lift exceeds the lift predicted by vortex lattice theory to 30 deg angle of attack. Suction augmentation is postulated to strengthen the vortex system by increasing its velocity and making it more concentrated. This causes the vortex breakdown to be delayed to a higher angle of attack

Taylor, A. H.↗
NASA NTRS1982

Instability of compressible boundary layers along curved walls with suction or cooling

This paper investigates the effect of suction of the boundary layer and wall cooling on the growth and development of three-dimensional longitudinal vortices over concave walls. The study is carried out for compressible flows for a range of Mach numbers from 0 to 5. Despite indications that small suction or small cooling rates locally reduce the critical Goertler number (destabilize the boundary layer), the overall effect of suction or cooling is to stabilize the boundary layer by reducing the amplitude ratio of the vortices. In case of suction, this becomes more difficult with increasing Mach number unless high suction rates are used. On the other hand, stabilizing the boundary layer with respect to Goertler vortices can hardly be achieved by cooling even when high cooling rates are used.

El-Hady, N. M.↗
NASA NTRS1982

Experiments on the stability of the flat-plate boundary layer with suction

Experiments have been conducted in the VPI and SU Stability Wind Tunnel on a flat-plate wind-tunnel model equipped with porous suction panels. Detailed hot-wire measurements were conducted in the laminar boundary layer to investigate the stabilizing effects of suction on growing Tollmien-Schlichting waves, which were introduced into the boundary layer using a vibrating ribbon. Special care was taken to minimize external disturbances and to avoid extraneous experimental bias. The measurements, which included mean-flow and disturbance-amplitude profiles across the boundary layer, showed that suction applied through discrete porous strips can be as effective as suction applied continuously over a much longer streamwise length. The measurements also showed that suction is more effective when placed forward, nearer to the region of neutral stability, than when placed in the region of maximum growth rate. These results also provided meaningful comparison with recent theory.

Reynolds, G. A.↗
NASA NTRS1983

Effect of suction and blowing on boundary-layer transition

The effects of wall blowing and suction on boundary-layer stability and transition are studied on a flat plate. Titanium panels, in which 0.063 mm diameter holes were drilled on 0.635 mm centers, are inserted on the plate. Suction level and distribution are variable. Disturbances are introduced by means of a vibrating ribbon and measurements of both mean-flow and disturbance-flow velocities are made with a hot wire. Disturbance amplitudes are measured as a function of Reynolds number, frequency, and suction characteristics and compared with the previous Dynapore results of Reynolds and Saric. Transition measurements under natural and forced conditions are also made. The stabilizing effects of suction are documented. It is also shown that very high local flow rates through the suction holes (which approach a hole Reynolds number of 300) do not destabilize the flow. On the other hand, weak blowing lowers the transition Reynolds number but is found not to cause serious problems.

Saric, W. S.↗
NASA NTRS1984

Effect of sidewall suction on flow in two-dimensional wind tunnels

A closed-form analysis of flow in a two-dimensional subsonic wind tunnel which uses sidewall suction around the model to reduce sidewall boundary-layer effects is presented. The model problem which is treated involves a flat plate airfoil in a tunnel with a suction window shaped to permit an analytic solution. This solution shows that the lift coefficient depends explicitly on the porosity parameter of the suction window and implicitly on the suction pressure differential. For a given sidewall displacement thickness, the lift coefficient increases as the suction-window porosity decreases.

Barnwell, R. W.↗
NASA NTRS1989

Transition flight experiments on a swept wing with suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth, depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1993

Effect of sidewall suction on flow in two-dimensional wind tunnels

A closed-form analysis of flow in a two-dimensional subsonic wind tunnel that uses sidewall suction around the model to reduce sidewall boundary-layer effects is presented. The model problem that is treated involves a flat plate airfoil in a tunnel with a suction window shaped to permit an analytic solution. This solution shows that the lift coefficient depends explicitly on the porosity parameter of the suction window and implicitly on the suction pressure differential. For a given sidewall displacement thickness, the lift coefficient increases as the suction-window porosity decreases.

Barnwell, Richard W.↗
NASA NTRS1952

Experimental Study of the Effects of Finite Surface Disturbances and Angle of Attack on the Laminar Boundary Layer of an NACA 64A010 Airfoil with Area Suction

A Langley low-turbulence wind-tunnel investigation of a porous NACA 64A010 airfoil section has been made to determine the effectiveness of area suction in maintaining full-chord laminar flow behind finite disturbances and at angles of attacks other than 0 degrees. Aero suction resulted in only a small increase in the size of a finite disturbance required to cause premature boundary-layer transition as compared with that for the airfoil without suction. Combined wake and suction drags lower than the drag of the plain airfoil were obtained through a range of low lift coefficient by the use of area suction.

FLOW, LAMINAR↗
NASA NTRS1999

High Reynolds Number Hybrid Laminar Flow Control (HLFC) Flight Experiment: Suction System Design and Manufacture - Report 4

This document describes the design of the leading edge suction system for flight demonstration of hybrid laminar flow control on the Boeing 757 airplane. The exterior pressures on the wing surface and the required suction quantity and distribution were determined in previous work. A system consisting of porous skin, sub-surface spanwise passages ("flutes"), pressure regulating screens and valves, collection fittings, ducts and a turbocompressor was defined to provide the required suction flow. Provisions were also made for flexible control of suction distribution and quantity for HLFC research purposes. Analysis methods for determining pressure drops and flow for transpiration heating for thermal anti-icing are defined. The control scheme used to observe and modulate suction distribution in flight is described.

Source record↗
NASA NTRS1989

Transition Flight Experiments on a Swept Wing With Suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth-depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1949

Exact Calculation of Laminar Boundary Layer in Longitudinal Flow over a Flat Plate with Homogeneous Suction

Lately it has been proposed to reduce the friction drag of a body in a flow for the technically important large Reynolds numbers by the following expedient: the boundary layer, normally turbulent, is artificially kept laminar up to high Reynolds numbers by suction. The reduction in friction drag thus obtained is of the order of magnitude of 60 to 80 percent of the turbulent friction drag, since the latter, for large Reynolds numbers, is several times the laminar friction drag. In considering the idea mentioned one has first to consider whether suction is a possible means of keeping the boundary layer laminar. This question can be answered by a theoretical investigation of the stability of the laminar boundary layer with suction. A knowledge, as accurate as possible, of the velocity distribution in the laminar boundary layer with suction forms the starting point for the stability investigation. E. Schlichting recently gave a survey of the present state of calculation of the laminar boundary layer with suction.

Iglisch, Rudolf↗