Search NASA⌕ Search

SEARCH · Search NASA

Results for “supercritical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured Alloys in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can have additional corrosion effects than found at ambient pressure conditions. Several wrought nickel-based commercial alloys (230, 263, 282, 617, 625, 740H) were exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure (0.1 MPa) and supercritical conditions (20 MPa) for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. Supercritical conditions affected the oxidation behavior of several alloys. Most notably, water-vapor assisted Cr-oxide volatilization was observed at 750 °C supercritical conditions. Many alloys did not form sufficient protective Cr-oxide scales at supercritical conditions, leading to increased oxidation at elevated pressure. Differences in oxidation behavior were also observed for 282 AM samples compared to their wrought counterparts, with the differences also dependent on the LPBF build parameters and post-production treatments (heat treatment and surface finishing procedures). The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought

Carney, Casey↗
DOE OSTI2021

Heat transfer and pseudo phase transition for low-Reynolds, mixed-convection channel flow in the supercritical thermodynamic regime

Fluids at supercritical thermodynamic conditions are inherently complex due to the large variations in thermodynamic and transport properties. Multiple recent numerical and experimental investigations indicate ongoing interest for these fluids, especially supercritical CO and supercritical water, for a variety of applications. The potential heat transfer benefits in this regime are directly influenced by the extreme variations in thermodynamic and transport properties, which occur at, and above, the critical point. Limited studies have been conducted for low-Reynolds/intermediate-Rayleigh numbers mixed-convection channel flow of supercritical water, which is the focus of this study. To investigate the thermally driven hydrodynamic instabilities in this regime, we use a high-order fully-implicit numerical method. As expected, in this channel configuration and flow regime, a competition arises between the forced and the natural convection. Buoyancy, driven by the thermal gradient at the wall, pushes the fluid upwards in the channel, while inertial forces drive the fluid from inlet to outlet. We observe significant differences in the heat transfer coefficient between the top and bottom walls of the channel flow, due to natural convection, and unstable plumes. We further quantify the buoyancy forces along the channel flow through evaluation of the Richardson number. Simulations show that with a higher negative Richardson number, there are more unstable structures along the channel, resulting in enhanced mixing. Furthermore, we demonstrate the existence of gas-like, liquid-like, and the possibility of pseudo-two-phase regimes in the supercritical fluid. The pseudo-two-phase regime occurs when the range of fluid temperatures is crossing the pseudo-critical line, also known as the Widom line. The density of the fluid varies significantly near the Widom line, and further influences the natural convection and heat transfer in the flow.

42 ENGINEERING↗
DOE OSTI2020

Supercritical Treatment Technology for Water Purification (Annual Final Report)

This project continued the development of the Supercritical Water Extraction – Enhanced Targeted Recovery (SWEETR™) technology, a novel desalination process for treating hypersaline brines. The overall objective is to demonstrate the technical and economic feasibility of an innovative, energy efficient, and robust supercritical desalination technology to treat hypersaline solutions and separating saltwater into a pure water stream and valuable recovered solids, resulting in zero liquid discharge (ZLD). The proposed technology, focuses on innovative methods of applying supercritical water to treat highly concentrated brine solutions without incurring a high energy penalty. Integrating the technology with solar energy reduces the energy cost for the system. The results obtained during the proof-of-concept testing demonstrate that the SWEETR™ concept is technically feasible and that supercritical water treatment is a viable option with strong merit for treating high salinity waters. The strategic design of the system provides the opportunity to localize the supercritical zone, which helps reduce the overall energy cost associated with the desalination process. The process can be tuned to remove only the amount of salts required to make the treated water “fit for purpose”, providing further opportunities to minimize energy costs. The ability to destroy organic compounds associated with the water while simultaneously being able to desalinate makes SWEETR™ uniquely fitted for treating aqueous streams such as produced water from oil and gas extraction which contain small amounts of organics. Such mixed contaminant streams pose an extreme challenge for other treatment options. Future work will further develop the SWEETR™ technology to take it from the bench-scale to the pilot-scale, and ready the technology for commercial application.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Design and Experimental Demonstration of an Additive Manufactured Smart Oxy-Methane Burner for High Pressure and Supercritical Combustion

Pressurized oxy combustion-based systems can improve efficiency by recovering latent heat of the steam in the Flue Gas and achieving 90% CO2 capture. In addition, the novel Directly Heated Supercritical Carbon Dioxide (DH-SCO2) power cycles can achieve high thermal efficiencies and provide nearly full carbon capture. Additionally, due to the reduction of flue gas at higher pressure, smaller system size and capital cost reductions are also possible. Recent thermodynamic analysis of the DH-SCO2 cycle performed by the UTEP research team shows that combustion conditions in the vicinity of 300 bar pressure and 1000-1400 K temperature allow for relatively high system efficiencies while operating within the limit of available combustor materials. However, the realization of a directly heated supercritical power cycle requires combustion systems to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K). The thermodynamic properties along with the combustion properties and kinetics are unexplored at such conditions. Additionally, the interaction of the supercritical environment with energy components is also unknown. High-pressure combustion tests are performed using a smart burner at some intermediate pressure ranges (<20 bar) to help minimize these knowledge gaps. The knowledge obtained from the high-pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. The obtained data will act as a systematic first step in testing at higher pressures of 100 and 300 bar pressures.The primary purpose of this Dissertation is to demonstrate the operability of a low NOx smart burner for oxy-methane combustion at high pressure (< 20 bar) and scalable up to supercritical conditions. A shear co-axial smart burner is designed with a real-time temperature monitoring capability to understand the burner face interaction at high-pressure conditions. In addition, the burner has four independent injection ports to allow the independent injection of fuel and dilution gases in the combustor. The maximum operating capability of the burner is 575 kWth. The burner was fabricated using a Laser Powder Bed Fusion process with Nickel Alloy 718. A powder removal technology was invented comprising ultrasonic vibration, liquid nitrogen exposure and media blasting to remove powders from internal channels of the burner. The burner operability tests are performed in the high-pressure combustor and the swirl combustor. The high-pressure combustor was used to investigate the burner operability and thermal soak back at different pressurized conditions. The experimental tests in high-pressure combustor up to 275 kWth input resulted in 16.5 bar chamber pressure and 198°C thermal soaks back to the burner. The burner was capable of providing the required thermal input within a 3% deviation range. In addition, soot formation occurred at high-pressure tests. The swirl combustor was used to observe the flame stability of the burner. Flame lift-off was observed for jet velocities above 450 m/s. Additionally, lift-off decreased for low co-flow velocities. CO2 dilution experiments showed increased flame instabilities for all conditions above 50% dilution ratios. At lower thermal inputs, partial flame blow-offs occurred for dilution ratios above 50%. All conditions significantly reduced the flame temperature and increased the flame lift-off height. Finally, a 2nd generation AM smart burner was designed using the knowledge from the 1st generation burner experiments. The 2nd generation burner incorporated two sets of swirlers with 0.9 swirl no. A cooling system was also designed for long-duration tests at higher pressures. The thermal input and division of the burner's power are kept the same as the 1st generation burner. The burner is to be fabricated using nickel-alloy 718 for high-pressure handling capability. The design can sustain at high-pressure conditions up to 100 bar.

Islam, Md Nawshad Arslan↗
DOE OSTI2021

Role of Inlet Boundary Conditions on Fuel-Air Mixing at Supercritical Conditions

Advanced engine design and alternative fuels present the possibility of fuel injection at purely supercritical conditions in diesel engines and gas turbines. The complex interactions that govern this phenomenon still need significant research, particularly the boundary conditions for fuel injection are critical for accurate simulation. However, the flow inside the injector itself is often omitted to reduce the computational efforts, and thus, velocity, mass flux, or total pressure is specified at the injector exit (or domain inlet), often with simplified velocity profiles and turbulence levels. This simplified inlet boundary treatment has minimal effects on results for conventional fuel injection conditions, however, the validity of this approach at supercritical conditions has not been assessed. Comprehensive real-gas and binary fluid mixing models have been implemented for computational fluid dynamics (CFD) analysis of fuel-air mixing at supercritical conditions. The model is verified using prior CFD results from the literature. The model is used to investigate the effects of the shape of axial velocity and mass fraction profiles at the inlet boundary with the goal to improve the comparison of predictions to experimental data. Results show that the boundary conditions have a significant effect on the predictions, and none of the cases match precisely with experimental data. Furthermore, the study reveals that the physical location of the inlet boundary might be difficult to infer correctly from the experiments and highlights the need for high-quality, repeatable measurements at supercritical conditions to support the development of relevant high-fidelity models for fuel-air mixing.

02 PETROLEUM↗
DOE OSTI2023

Thermohydraulic experiments on a supercritical carbon dioxide–air microtube heat exchanger

Heat exchangers are critical components in supercritical CO 2 Brayton cycles and provide necessary heat input, recovery, and dissipation. Tubular heat exchangers with unconventionally small tube sizes (tube diameters less than 5 mm) are promising components for supercritical CO 2 cycles and potentially provide excellent structural stability with wide scope of application. This paper provides essential design and fabrication guidelines for a compact shell-and-tube heat exchanger with microtubes (with an inner diameter equal to 1.75 mm). A heat exchanger test rig is used to evaluate the thermohydraulic performance of this heat exchanger with supercritical CO 2 and air as working fluids. Thermohydraulic data are reported for more than forty sets of experiments with varying Reynolds numbers for shell and tube flows. Critical performance metrics are calculated from the data and compared with predictions from a previously described numerical model. The average deviations between the experimental and model results fall within 10% for all critical metrics. This excellent agreement validates the numerical model for supercritical CO 2 heat exchanger optimization and scale-up.

42 ENGINEERING↗
DOE OSTI2020

Reexamining supercritical gas adsorption theories in nano-porous shales under geological conditions

Adsorption is an important phenomenon in surface chemistry, especially for nano-porous shales. In the shale gas-in-place, adsorbed gas could contribute up to 85%. However, adsorption is hard to quantitatively characterize due to different adsorption mechanisms, patterns, surfaces, and pore sizes. Moreover, key thermodynamic parameters, such as the enthalpy of adsorption, are challenging to determine due to uncertainties in adsorbed gas densities used in constructing absolute isotherms. In this paper, we revisit the Brunauer, Emmett, and Teller (BET) model, analytically simplify Ono-Kondo (OK) models for subsurface shales, and compare commonly used mono- and multilayer adsorption models (e.g., Langmuir, supercritical Dubinin-Radushkevich (SDR), supercritical BET (SBET), and simplified OK (OKs) models) with recently proposed pressure-dependent adsorption densities to develop a practical and reliable methodology that can be used in the supercritical state, typical for subsurface black shale conditions.Three independent data sets were used for nitrogen and methane adsorption isotherms at different temperatures. Furthermore, we demonstrate that adsorption predicted by the SDR model is comparable or lower than that predicted by the SBET model, but higher than the amounts predicted by Langmuir and OK models. The nitrogen BET method tends to underestimate the accessible SSA for methane. Measurement of isosteric heat of adsorption is suggested instead of the experimental fitting method, due to the significant difference between the calculated results by two commonly used methods. Experimental fitting and simulation methods are also briefly reviewed to guide future research on shale gas adsorption.

58 GEOSCIENCES↗
DOE OSTI2022

Iron corrosion in the “inert” supercritical CO 2 , ab initio dynamics insights: How impurities matter

Metal corrosion from exposure to supercritical fluids is a long-standing challenge lacking atomistic understanding for effective corrosion prevention in diverse important applications. Here, in this work, reactions relevant to corrosion in supercritical CO 2 (sCO 2 ), with H 2 O and NO 2 as impurities, are revealed using ab initio molecular dynamics and enhanced sampling methods. While little reactivity is observed in bulk sCO 2 , the iron surface is found to play a crucial almost-catalytic role in its own corrosion, activating the inert CO2 and hence facilitating $\ast$HCO 3 – and $\ast$CO 3 2– formation at the interface. Moreover, the hydrogen bond network of $\ast$H 2 O assists the H shuttling to the activated CO 2 and impurities, forming reactive species observed in experiments. Such atomistic insight elucidates the reaction mechanisms of metal corrosion in aqueous and supercritical fluids and can point to possible remedies.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Beneficiation of coal using supercritical water and carbon dioxide extraction: sulfur removal

Abstract This work explores the use of carbon dioxide, water, and their mixtures as solvent for the precombustion beneficiation of raw coal without using any toxic mineral acids in the temperature range of 200–400 °C. The fluid polarity, ionic constant, and supercritical point can be adjusted by H 2 O/CO 2 ratio and temperature. Adding carbon dioxide to hydrothermal fluid also increases the ionization by forming carbonic acid. Extractions with supercritical fluids have several benefits including enhanced mass transport, ease of separation and recycle, wide range of extractive capability and tunability, better inherent safety, and in the case of carbon dioxide and water–low cost. A semi-continuous extraction system was designed and built in which pressure, temperature and the relative flow rates of CO 2 and H 2 O can be controlled. Coal powder is kept in a packed bed and the extraction is carried out at 143 bar pressure. Using sulfur as a model heteroatom, extractive efficiency is examined as a function of the temperature, fluid composition, fluid flow, and extraction time. The results indicate that carbon dioxide, water, and supercritical water-carbon dioxide (ScWC) all can effectively extract about 50% of total sulfur from bituminous coal in 1 h. Extraction above 350 °C decreased effectiveness, and extraction above the supercritical point of pure water caused hydrothermal carbonization. ScWC extraction may provide necessary control to prevent organic dissolution while removing sulfur.

DeCuir, Matthew J.↗
DOE OSTI2020

Volumetric efficiency and pressure pulsations of a triplex reciprocating supercritical CO 2 pump

A reciprocating triplex pump has been integrated into a closed-loop supercritical carbon dioxide test facility. The pump is designed to compress liquid or supercritical carbon dioxide and has a maximum volumetric flow rate of 51 L/min. A sweep across the pump’s speed range of 100–1000 rev/min was performed with inlet conditions between 60 and 160 bar. The volumetric efficiency was found to increase as pump speed increased from 10 to 40 % before it plateaued at higher pump speeds. The mechanical efficiency increased linearly with pump speed and was not affected by system pressure. Pressure pulsations caused by the plungers and valves were also measured at each speed. Additionally, a 35-liter buffer volume, connected near the pump’s discharge was isolated at each speed to determine its effectiveness as a pulsation dampener. Overall the reciprocating pump was shown to perform exceptionally with liquid or supercritical inlet conditions applicable to many supercritical fluid applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Chemistry and Dynamics of Supercritical Carbon Dioxide and Methane in the Slit Pores of Layered Silicates

In the mid 2010s, high-pressure diffraction and spectroscopic tools opened a window into the molecular-scale behavior of fluids at the conditions of many CO 2 sequestration and shale/tight gas reservoirs - conditions where CO 2 and CH 4 are present as variably wet supercritical fluids. Integrating high-pressure spectroscopy and diffraction with molecular modeling has revealed much about the ways that supercritical CO 2 and CH 4 behave in reservoir components, particularly in the slit-shaped micro- and meso-pores of layered silicates (phyllosilicates) abundant in caprocks and shales. This Account summarizes how supercritical CO 2 and CH 4 behave in the slit pores of swelling phyllosilicates as functions of the H 2 O activity, framework structural features, and charge-balancing cation properties at 90 bar and 323 K – conditions similar to a reservoir at ~1 km depth. Slit pores containing cations with large radii, low hydration energy, and large polarizability readily interact with CO 2 , allowing CO 2 and H 2 O to adsorb and co-exist in these interlayer pores over a wide range of fluid humidities. In contrast, cations with small radii, high hydration energy, and low polarizability weakly interact with CO 2 leading to reduced CO 2 uptake and a tendency to exclude CO 2 from interlayers when H 2 O is abundant. The reorientation dynamics of confined CO 2 depends on the interlayer pore height, which is strongly influenced by the cation properties, framework properties, and fluid humidity. The silicate structural framework also influences CO 2 uptake and behavior - for example, smectites with increasing F-for-OH substitution in the framework take up greater quantities of CO 2 . Reactions that trap CO 2 in carbonate phases have been observed in thin H 2 O films near smectite surfaces, including a dissolution-reprecipitation mechanism when the edge surface area is high and an ion exchange-precipitation mechanism when the interlayer cation can form a highly insoluble carbonate. In contrast, supercritical CH 4 does not readily associate with cations, does not react with smectites, and is only incorporated into interlayer slit mesopores when (i) the pore has a $z$-dimension large enough to accommodate CH 4 , (ii) the smectite has low charge and (iii) the H 2 O activity is low. In conclusion, the adsorption and displacement of CH 4 by CO 2 and vice-versa have been studied on the molecular scale in one shale, but opportunities remain to examine behavioral details in this more complicated, slit-pore inclusive system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effects of Supercritical CO 2 Injection on the Shale Pore Structures and Mass Transport Rates

Characterizing the pore structures and transport properties of low-permeability shales is critical for evaluating these formations as potential seals or storage sites for geological CO 2 sequestration. Here, we use low-pressure gas adsorption in conjunction with nuclear magnetic resonance (NMR) to characterize the pore-size distribution of shales before and after injection of supercritical CO 2 . Nitrogen gas was used as the detecting phase for the adsorption experiments and pentane liquid was used for the NMR experiments. We also performed time-resolved NMR and gravimetric microbalance measurements to observe mass transport during desaturation. We use these data to estimate the self-diffusion coefficient of pentane and changes in the saturation state of the pore network. We analyzed samples with a range of compositions from the Wolfcamp shale before and after exposure to supercritical CO 2 for 3 days. Integrating the gas adsorption and NMR data shows how supercritical CO 2 injection alters the pore-size distribution for pore sizes <1 nm to 1 mm. Finally, our results provide insights on how the pore structure and mass transport properties of different shale lithologies may evolve during storage of supercritical CO 2 .

58 GEOSCIENCES↗
DOE OSTI2023

The Local Electronic Structure of Supercritical CO 2 from X-ray Raman Spectroscopy and Atomistic-Scale Modeling

Supercritical CO 2 is encountered in several technical and natural systems related to biology, geophysics, and engineering. While the structure of gaseous CO 2 has been studied extensively, the properties of supercritical CO 2 , particularly close to the critical point, are not well-known. Here, in this work, we combine X-ray Raman spectroscopy, molecular dynamics simulations, and first-principles density functional theory (DFT) calculations to characterize the local electronic structure of supercritical CO 2 at conditions around the critical point. The X-ray Raman oxygen K-edge spectra manifest systematic trends associated with the phase change of CO 2 and the intermolecular distance. Extensive first-principles DFT calculations rationalize these observations on the basis of the 4sσ Rydberg state hybridization. X-ray Raman spectroscopy is found to be a sensitive tool for characterizing electronic properties of CO 2 under challenging experimental conditions and is demonstrated to be a unique probe for studying the electronic structure of supercritical fluids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Influence of Equation-of-States on Supercritical CO2 Combustion Mixtures

Abstract Fossil fuel based direct-fired supercritical CO2 (sCO2) cycles are gaining the attention of industry, academia, and government due to their remarkable efficiency and carbon capture at high-source temperatures. Modeling plays an important role in the development of sCO2 combustors because experiments are very expensive at the designed operating conditions of these direct-fired cycles. Inaccurate density estimates are detrimental to the simulation output. Hence, this work focuses on comprehensive evaluation of the influence and applicability of various equation-of-states (EOS) which are being used in the supercritical combustion modeling literature. A state-of-the-art supercritical combustion modeling methodology is used to simulate counter-flow supercritical CO2 flames by using various equation-of-states. The results show that using the corresponding state principle to evaluate compressibility factor is not accurate. Also, van der Waal type EOSs predictions can be as accurate as complex Benedict–Webb–Rubin EOSs; hence van der Waal EOSs are more suitable to simulate sCO2 combustor simulations. Non-ideal effects are significant under the operating conditions considered in this work. The choice of EOS significantly influences the flame structure and heat release rate. Also, assuming the binary interaction parameter as zero is reasonable in sCO2 combustion simulations.

Energy & Fuels↗
DOE OSTI2022

INVESTIGATION OF TURBULENT JETS, SPRAYS, AND SUPERCRITICAL MIXING BY TIME RESOLVED RAINBOW SCHLIEREN DEFLECTOMETRY

As technological advancements have enabled higher efficiency compression ignition (CI) engines (diesel engines) by operating at higher pressures and temperatures, the mechanisms of fuel-air mixing are postulated to change. Thus, there is a greater need for experimental data to develop and verify new phenomena. However, the fast time scales and harsh environments associated with CI engines present many experimental difficulties and requires high quality non-intrusive diagnostics to obtain useful data. The diagnostics itself must be validated prior to its implementation in an engine environment. The purpose of this research is to advance rainbow schlieren deflectometry (RSD) to study turbulent fuel sprays including the effects of supercritical mixing in CI engine environments. This objective is met by developing and applying quantitative RSD, for the first time, to three separate aspects of fuel sprays: 1) turbulent mixing, 2) phase boundaries, and 3) non-ideal gas mixing. First, quantitative RSD is demonstrated for turbulent mixing in a canonical helium jet. Rayleigh scattering data in the literature is used to validate the concentration measurements obtained by RSD. The results also provide explanations for phenomena occurring in the helium jet and provide data not yet present in the literature. Second, RSD is applied to high pressure multi-phase fuel sprays and new methodologies are developed to distinguish the liquid region from the vapor region and to quantify the in-between region on a probabilistic basis. Isolating liquid and vapor regions generally requires two separate diagnostics, e.g., Mie scattering (liquid region) and Rayleigh scattering (vapor region). However, the results of this study demonstrate that RSD can be used as a single diagnostic to measure both liquid and vapor boundaries. Third, the optical-to-thermodynamic relations associated with refrac-tometry are investigated under non-ideal gas mixing conditions to develop a generalized relationship valid for both ideal or non-ideal gas mixing. The last part of this research develops the theoretical tools to understand and experimentally realize supercritical mixing at diesel conditions. Guided by the theoretical analysis, RSD is applied to compare supercritical versus transcritical mixing at CI conditions using a constant pressure test rig. It is found that while fully supercritical mixing ers benefits in diesel engines, i.e, faster mixing times (50% higher velocities), the absence of droplets which cause high levels of particulate emissions, etc., it would be difficult to achieve in practice because of the requirements of fuels with low critical temperature and/or substantial fuel preheating.

02 PETROLEUM↗
DOE OSTI2022

Selective recovery of critical materials in zero-liquid discharge supercritical water desalination

Zero-liquid discharge desalination techniques are being actively studied as alternative means to produce drinkable water and recover valuable resources without polluting the environment. Supercritical water desalination is one of such alternatives that can overcome the technical and environmental challenges in standard desalination techniques. In addition to these attractive features, this work explores the possibility of utilizing supercritical water desalination for the selective recovery of strategic (critical) materials as co-products. Here, to validate the technical and economic feasibility of the process, we prepared model brine solutions that consist of sodium, neodymium, and different anions and conducted a series of desalination experiments. The results were analyzed experimentally and theoretically and were utilized to evaluate the economic feasibility of the process. When a few tens or hundreds of parts-per-million critical materials are dissolved in the feed, the proposed method becomes more cost-effective in producing critical materials than existing technologies. In addition, it does not discharge any concentrated contaminants while producing drinkable water. These results suggest that supercritical water desalination can recover critical materials while producing freshwater in an economically feasible fashion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Thermodynamic analysis and optimization of supercritical carbon dioxide Brayton cycles for use with low-grade geothermal heat sources

The transcritical carbon dioxide Rankine cycle has emerged as an alternative for power generation in low-grade heat applications. However, the low heat rejection temperatures required for condensing the carbon dioxide is almost prohibitive for many locations. A simple solution is the adoption of a supercritical carbon dioxide Brayton cycle which does not need such low temperature heat sinks. This power cycle has been poorly studied previously in low-grade heat applications. Therefore, with the aim of determining the performance and feasibility of the supercritical carbon dioxide Brayton cycle from thermodynamic viewpoint, using a low-grade geothermal heat source, this paper presents a comparative thermodynamic analysis between four different supercritical carbon dioxide Brayton cycles. For this purpose, detailed models were developed and solved by coupling the thermodynamic model with the thermal-hydraulic model of a Printed Circuit Heat Exchanger. Subsequently, simulations of a base case, a parametric analysis, and an optimization using Genetic Algorithms, were carried out. Results show that there is a combination of operating conditions that maximizes the electrical output of the system. Besides, some values of the minimum pressure of the cycles can increase substantially the precooler cooling water pumping power. At the optimum design point, using a 20 kg/s geothermal brine stream at 150 °C as heat source with a minimum allowable reinjection temperature of 70 °C, the Intercooled Recuperated Brayton Cycle achieved the highest electric power output, energy and exergy efficiencies, obtaining values of 779.99 kW, 11.51%, and 52.49%, respectively. The other feasible alternatives were the Recuperated Brayton Cycle, the Simple Brayton Cycle and the Intercooled Brayton Cycle, ranked, in that order.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Supercritical, liquid, and gas CO 2 reactive transport and carbonate formation in portland cement mortar

In this paper, we investigate carbonate formation and reactive transport rate in variably saturated portland cement mortars when high concentrations of gas, liquid, or supercritical CO 2 flow through their pore network. Xray computed tomography completed during CO 2 flow is used to quantify the microstructural evolution as the mortar carbonates. After in situ tests, higher resolution scans, thermogravimetric analysis, and desorption isotherm analysis are performed to further quantify microstructural changes. We found that at dry conditions supercritical CO 2 moves more rapidly through the pore space and precipitates more carbonates than liquid or gas CO 2 . However, at 50% degree of saturation (DOS) the CO 2 state did not affect the rate of transport in that each specimen exposed to a different CO 2 state carbonated within the first hour of CO 2 exposure. When the pore space is at 50 or 100% DOS, supercritical CO 2 did not react with hydration products more rapidly nor did it result in more carbonate formation during exposure compared to gas or liquid CO 2 . The amount of Ca(OH) 2 that contributes to CaCO 3 formation is correlated to the DOS. For the mortar composition analyzed, Ca(OH) 2 contributes to approximately 40% of the carbonates formed in the 50% DOS specimens and 15% in the 100% DOS specimens. In other words, as the amount of moisture in the pore space increases, phases other than Ca(OH) 2 contribute to more than 50% of the total CaCO 3 formed.

42 ENGINEERING↗