Search NASA⌕ Search

SEARCH · Search NASA

Results for “supersaturation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Growth of deuterium supersaturated surface layer with increasing ion flux and fluence in plasma-exposed tungsten

Deuterium supersaturated surface layer (DSSL) in tungsten, a few nm thick layer exhibiting extremely high deuterium content (> 5%), has been studied as a function of deuterium plasma ion flux and fluence. Tungsten samples were exposed at 400 K and deuterium ion energy of ∼ 60 eV. The deuterium ion flux spanned over an order of magnitude, being 7.3 × 10 20 , 4.2 × 10 21 , and 3.8 × 10 22 D/m 2 . The fluence ranged from 3.4 × 1024 to 3.4 × 1025 D/m2. The samples and their deuterium content were analyzed by nuclear reaction analysis (NRA), scanning transmission electron microscopy (STEM), and thermal desorption spectroscopy (TDS). The largest thickness of DSSL was found to be around 10.5 nm and was observed in the case of the highest exposure flux and fluence, whereas the layer was only about 3.8 nm thick in the case of the lowest value of the two parameters. The thickness of the DSSL was found to monotonically increase with both deuterium flux and fluence. Finally, similar to the thickness, the estimated D concentration seems to follow the same trend, increasing from the lowest value of around 3 at.% to the highest value of around 5 at.%.

Deuterium↗
DOE OSTI2023

Maximum Supersaturation in the Marine Boundary Layer Clouds Over the North Atlantic

Abstract The maximum supersaturation ( S x ) in clouds is a key parameter affecting the cloud's microphysical and radiative properties. We investigate the S x of the marine boundary layer clouds by combining airborne and surface observations in the Eastern North Atlantic. The cloud droplet number concentration ( N c ) in the least diluted cloud cores agrees well with the number concentration of particles larger than the Hoppel Minimum (HM) ( N >HM ) below clouds, indicating that the HM represents the average size threshold above which particles are activated to form cloud droplets. The S x values derived from surface observations vary from 0.10% to 0.50% from June 2017 to June 2018, with a clear seasonal variation exhibiting higher values during winter. Most of the S x variance (∼60%) can be explained by the cloud condensation nuclei (CCN) concentration and updraft velocity ( w ), with the CCN concentration playing a more important role than w in explaining the variation of S x . The influence of CCN concentration on S x leads to a buffered response of N c to aerosol perturbations. The response of N c to low aerosol concentration during winter is further buffered by the high w . The global Community Earth System Model (CESM) simulated S x values in the Azores have a positive bias compared to measured S x , likely due to overestimated w and underestimated CCN concentration. The CESM simulated S x exhibits higher values further north over the North Atlantic Ocean, which is attributed to stronger w . The suppression of S x by aerosol is also evident in regions with high CCN concentrations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Spontaneously supersaturated nucleation strategy for high reproducible and efficient perovskite solar cells

High-quality perovskite films are predominantly prepared by anti-solvent assisted spin-coating method. How- ever, small device size and narrow operation window limit their applications in practical and scalable production. Here, a spontaneously supersaturated nucleation strategy is developed to fabricate high-quality perovskite films without any antisolvents. The rapid precipitation behavior of the precursor solutions could be triggered by the volatilization of methylamine ethanol at the initial film formation stage, forming uniform and compact intermediate phase films. Mirror-like large area (10 cm × 10 cm) methylammonium lead triiodide (MAPbI 3 ) perovskite films with micrometer-sized grains can be achieved by phase transition via annealing. The average power conversion efficiency (PCE) of 19.4% is achieved for 0.1 cm 2 perovskite solar cells (PSCs). The 1 cm 2 device shows a PCE of 17.57% and retains 96.8% after aging for 39 days in the air with a relative humidity of 5–30%. The perovskite module based on the perovskite films prepared by our strategy exhibits a PCE of 13.13%. Here, the perovskite film fabrication method developed in this work shows high reproducibility of the fabrication process due to the spontaneous nucleation process. Meanwhile, it also exhibits significant potential in the application of scalable solution processing deposition techniques toward the commercialization of PSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Deuterium supersaturated surface layer in tungsten: ion energy dependence

Abstract Properties of deuterium (D) supersaturated surface layers (DSSLs) formed in tungsten (W), such as thickness, internal microstructures, and D retention, are experimentally investigated as a function of the incident ion energy, E i . W samples were exposed to D plasmas in the PISCES-A linear plasma device in a range of E i ∼ 45–175 eV, while other plasma exposure parameters were fixed: sample temperature, T s , ∼423 K, ion flux, Γ i , ∼1.2 × 10 21 m −2 s −1 , and fluence, Φ i , ∼3.0 × 10 24 m −2 . High-resolution, cross-sectional, transmission electron microscopy observations confirm that (1) a DSSL forms even at the lowest E i ∼ 45 eV, (2) the DSSL thickness, Δ t DSSL , is found to decrease with decreasing E i from ∼11–12 nm at E i ∼ 175 eV to ∼5–6 nm at ∼45 eV, and to agree with approximately the maximum implantation depth calculated using SDTrimSP, and (3) high-density D nanobubbles with a diameter of ∼1 nm or less exist inside the DSSL, which is deemed to validate a theory-predicted vacancy stabilization process due to trapping of a solute D atom(s). Utilizing a D areal density of ∼4.2 × 10 19 m −2 in the first 14 nm from the surface at E i ∼ 75 eV from nuclear reaction analysis and the measured E i dependence of Δ t DSSL , our previous laser-induced breakdown spectroscopy data is updated: both dynamic and static D retention increase with decreasing E i , and the D/W atomic fraction during plasma exposure reaches ∼0.3 at E i ∼ 45 eV. A possible DSSL formation mechanism is proposed.

Physics↗
DOE OSTI2024

Reply to Comment on ‘Deuterium supersaturated surface layer in tungsten: ion energy dependence’

Abstract We reply to the comment by Li et al (submitted to Nucl. Fusion with this response) on our recent paper Nishijima et al (2023 Nucl. Fusion 63 126003). In this response, we address the existence of an incident ion energy, E i , threshold for the deuterium (D) supersaturated surface layer (DSSL) formation with a newly conducted D plasma exposure experiment at E i ∼ 20 eV. It is also further demonstrated, based on new experiments where the ion flux, fluence, and sample temperature are scanned, that non-kinetic (ballistic) processes play a role in the DSSL formation and growth. In addition, the effect of impurities in our plasma is discussed also with a new analysis of the surface composition made after a D plasma exposure.

Nishijima, D. (ORCID:0000000231194827)↗
DOE OSTI2021

Superior High-Temperature Strength in a Supersaturated Refractory High-Entropy Alloy

Refractory high-entropy alloys (RHEA) show promising applications at high temperatures. However, achieving high strengths at elevated temperatures above 1,173K is still challenging due to heat softening. Using intrinsic material characteristics as the alloy-design principles, a single-phase body-centered-cubic (BCC) CrMoNbV RHEA with high-temperature strengths (beyond 1,000 MPa at 1,273 K) is designed, superior to other reported RHEAs as well as conventional superalloys. The origin of the high-temperature strength is revealed by in-situ neutron scattering, transmission-electron microscopy, and first-principles calculations. The CrMoNbV’s elevated-temperature strength retention up to 1,273 K arises from its large atomic-size and elastic-modulus mismatches, the insensitive temperature dependence of elastic constants, and the dominance of non-screw character dislocations caused by the strong solute pinning, which makes the solid-solution strengthening pronounced. The alloy-design principles and the insights in this study pave the way to design RHEAs with outstanding high-temperature strength.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhancements in Cloud Condensation Nuclei Activity From Turbulent Fluctuations in Supersaturation

Abstract The effect of aerosols on the properties of clouds is a large source of uncertainty in predictions of weather and climate. These aerosol‐cloud interactions depend critically on the ability of aerosol particles to form cloud droplets. A challenge in modeling aerosol‐cloud interactions is the representation of interactions between turbulence and cloud microphysics. Turbulent mixing leads to small‐scale fluctuations in water vapor and temperature that are unresolved in large‐scale atmospheric models. To quantify the impact of turbulent fluctuations on cloud condensation nuclei (CCN) activation, we used a high‐resolution Large Eddy Simulation of a convective cloud chamber to drive particle‐based cloud microphysics simulations. We show small‐scale fluctuations strongly impact CCN activity. Once activated, the relatively long timescales of evaporation compared to fluctuations causes droplets to persist in subsaturated regions, which further increases droplet concentrations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Coalescence dynamics of prismatic dislocation loops due to vacancy supersaturation

Recovery processes in metals with a high defect concentration are at the heart of a structural alloy's usability in engineering applications. However, such processes take place via nonconservative mechanisms mediated by point defect diffusion and are governed by their interactions with the underlying microstructure. Indeed, one of the main challenges in studying recovery processes is their intrinsic multiscale complexity, which often negates the direct use of experimental techniques. Here, in this Research Letter, we study the mechanism of dislocation loop coalescence in metals by simulating the interaction dynamics between vacancies and prismatic loops using a stochastic framework that seamlessly bridges point defect kinetics with dislocation mechanics. Our simulations reveal two fundamental discoveries: first, that climb processes are governed by local fluctuations that are not captured by continuum elastodiffusion models, and, second, that prismatic loops create internal traps for vacancies, leading to the formation of rings around the perimeter of the loops that affect how coalescence takes place. Our results show an excellent agreement with in situ experimental observations of loop coalescence in Fe under irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Supersaturating Water with CO 2 via Nanobubble Formation

The subsurface storage of CO 2 is limited by the solubility of CO 2 in brine. One proposed solution to increase the volume fraction of CO 2 in a reservoir is by injecting the CO 2 at high pressure in nanobubble form. These nanobubbles, diameter <50 nm, would be small enough that they would only undergo Brownian motion, preventing them rising under buoyancy and escaping the formation. There has also been some experimental work that suggests the present of these nanobubbles significantly (~2x) increase the solubility of gaseous CO 2 in the aqueous phase. NETL and ExxonMobil will test the viability of this strategy to increase the volume fraction of CO 2 in a subsurface reservoir, determine the stability of these nanobubble systems, and understand the ultimate limits of increasing the CO 2 volume fraction.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

CCN Measurements at Urban Site during CoURAGE

Cloud condensation nuclei (CCN) measurements were collected during CoURAGE from March - June 2025 at the BSEC urban atmospheric chemistry supersite (39.32057 N, 76.6246 W). CCN number concentrations (# cm-3) were obtained at a frequency of 1 second using a cloud condensation nuclei counter (CCN-100, Droplet Measurement Technologies). The CCN counter was operated in stepping mode, measuring CCN over a range of supersaturations from 0.2 to 1.0%. The settings of the instrument were set such that the supersaturation increased in increments of 0.2% up to the maximum supersaturation, and then decreased in increments of 0.2% down to the minimum supersaturation in a repeating cycle. The supersaturation of the instrument was calibrated weekly using ammonium sulfate. The weekly calibrated supersaturation values have been applied to the data. Data during transitions between supersaturation values were removed and replaced with a value of -999. Transitions are defined as the first 210 seconds after a new supersaturation value to ensure the instrument has stabilized following a change in supersaturation. Data were also flagged with a value of -999 if there were concerns with the function of the instrument, specifically the presence of alarm codes, fogging of the optical particle counter (1st stage monitor > 0.4 V), or a sheath to sample flow ratio outside the expected range (< 9 or > 11).

CCN number density↗
DOE OSTI2023

CCN data from TAMU TRACER campaign in the Houston TX region from July to September 2022

During TRACER, the Texas A&M Rapid Onsite Atmospheric Measurements Van (ROAM-V) was deployed to capture airmasses behind (maritime) and ahead (continental) of the passage of the sea-breeze front through Houston. On select sampling days, ROAM-V sampled in the morning/mid-day on the coast and then transited to a second inland site for the afternoon/evening. The suite of instruments deployed on ROAM-V included a Condensation Particle Counter (CPC; GRIMM Model 5.403 CPC), Scanning Mobility Particle Sizer (SMPS; TSI 3750 detector, TSI 3082 classifier, TSI 3088 neutralizer, TSI 3081A Differential Mobility Analyzer), Cloud Condensation Nuclei counter (Droplet Measurement Technologies CCN Counter), micro pulse lidar (Droplet Measurement Technologies Micro Pulse LiDAR (miniMPL)), and a Davis Rotating Uniform size-cut Monitor (DRUM; DRUMAir 4-DRUM). Before sampling at each location, the latitude and longitude were recorded using the GPS on the phone application “My Altitude”. Onboard the ROAM-V, aerosol samples are drawn through a shared isokinetic inlet at a flow rate ranging from 3.5 to 7.0 LPM. A portion of this flow is directed through a cyclone impactor (Brechtel, Inc. Model SCC 0.732) and 0.5 LPM is directed to the CCN. To calculate particle losses, we used a two-step method. First, the measured SMPS size distributions were used to calculate particle loss through the inlet during sampling. Second, the corrected SMPS data was used to calculate the average of the total losses per scan down the CCN line. Then, the correction was applied to the CCN data. This calculation was done separately for each deployment location due to changes in the measured size distributions between locations. Particle loss from diffusion (based on Kesten, 1991 and Gormley, 1949), inertial impaction in 90-degree bends (based on Aerosol Measurement, 2011 and Crane, 1977), and cyclone impactor efficiency (based on Dirgo, 1985) were included in the loss calculation. When the SMPS was not sampling at a location (in the case of an instrument malfunction or operator error), the reported CPC data was corrected with an average of the total losses for the entire campaign at the specified deployment location (e.g., if we needed to correct Galveston data, then the average of all calculated losses at Galveston was taken). These flatline corrections were used for all data on 22/07/13, 22/07/20, 22/07/22, and the data from Galveston on 22/08/09. The supersaturation uncertainty is estimated conservatively at +/- 0.03%, where variation in the inlet temperature, pressure, and calibration technique prevents a more accurate measurement. Confidence in the reported supersaturation measurements is based on a pre-campaign calibration (following the methods from our previous work and Deng, 2014 based on Rose, 2008) in addition to inter-comparisons with the DOE for two days (22/08/18 and 22/09/01) where TAMU was co-located with AMF1. The inter-comparisons show good agreement between our instrument and the DOEs instrument on both days at all supersaturations. After the last inter-comparison on 22/09/01, there was no indication of a malfunction by our instrument through the rest of the campaign. Unfortunately, the instrument was dropped during demobilization. A post-campaign calibration was conducted, which showed a substantial departure from the pre-campaign calibration. The drop may have damaged the instrument’s ability to produce the desired supersaturations. Therefore, we do consider the data after 22/09/01 to be correct, but it should be used with caution. The CCN counter sampled for 3 minutes at each supersaturation setpoint (0.2, 0.4, 0.6, 0.8, 1.0, and 1.2%). At the end of a cycle, the instrument was set to 0.01% supersaturation for 5 minutes. The data is comprised of the last 60 seconds of each supersaturation set point (0.2, 0.4, 0.6, 0.8, 1.0, and 1.2%) to ensure the instrument stabilized and was able to reach thermal equilibrium. We removed the data during the periods where there were operational difficulties, setup, or maintenance. This data was collected for ARM Field Campaign AFC07055 and supported by DOE ASR grant DE-SC0021047. For any further questions, please feel free to contact the instrument PI, Sarah D. Brooks, sbrooks@tamu.edu. Rose et. al. Calibration and Measurement Uncertainties of a Continuous-Flow Cloud Condensation Nuclei Counter (DMT-CCNC): CCN Activation of Ammonium Sulfate and Sodium Chloride Aerosol Particles in Theory and Experiment. Atmos. Chem. Phys., 8, 1153-1179, 2008. Deng et. al. Using Raman Microspectroscopy to Determine Chemical Composition and Mixing State of Airborne Marine Aerosols over the Pacific Ocean. Aerosol Science and Technology, Vol 48, Issue 2, 2014. Kesten et. al. Calibration of a TSI Model 3025 Ultrafine Condensation Particle Counter. Aerosol Science and Technology, 15:2, 107-111, 1991. Gormley et. al. Diffusion from a Stream Flowing through a Cylindrical Tube. Proceedings of the Royal Irish Academy, Vol 52, 163-169, 1948. Aerosol Measurement: Principles, Techniques, and Applications, Third Edition. John Wiley & Sons, Inc, 2011. Crane et. al. Inertial Deposition of Particles in a Bent Pipe. Journal of Aerosol Science, Vol 8, 161-170, 1977. Dirgo et. al. Cyclone Collection Efficiency: Comparison of Experimental Results with Theoretical Predictions. Aerosol Science and Technology, 4:4, 401-415, 1985.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Comments on 'Do ultrafine cloud condensation nuclei invigorate deep convection?'

Here we elaborated on the deficiencies associated with the theoretical arguments and model simulations in Grawbowski and Morrison (2020; GM20), and showed that the concept of convective invigoration by aerosols can be supported by both accurate theoretical analysis and explicit physics modeling with prognostic aerosols and supersaturation. Above the freezing level, droplet freezing itself does not change mass loading and the latent heat release resulting from freezing leads to an increase in the buoyancy. The derivation in GM20 is erroneous because of omitting the liquid water sink term. They also ignored the effect of enhanced latent heating from the subsequent growth processes (deposition and riming) after freezing. Regarding aerosol effect on condensational growth, the quasi-steady assumption for supersaturation as adopted in GM20 is invalidated especially when droplet number concentration is low and updraft is strong from both theoretical analysis and our bin microphysics modeling results. The quasi-steady assumption makes condensation independent of droplet number and size and therefore reduces the overall aerosol effects on cloud dynamics. Studying aerosol effects on clouds particularly deep convective clouds requires the exact solution of supersaturation. Any assumption imposed to supersaturation such as saturation adjustment and quasi-steady approximation leads to incorrect aerosol effects on diffusional growth. The exact supersaturation equation clearly shows that condensation depends on droplet number and size, and more droplets in the polluted clouds increase condensation (thus lower supersaturation), leading to enhanced buoyancy and updraft speeds.

Convective invigoration, deep convective clouds, a↗
DOE OSTI2021

Enhancing Steam-Side Heat Transfer via Microdroplet Ejection using Inorganic Coatings

During condensation of water on a superhydrophobic nanostructured surfaces, droplets coalesce and jump (droplet ejection) due to the release of excess surface energy. Meticulously designed nanostructured surfaces or coatings capable of droplet ejection can enhance heat transfer performance by easy removal of droplets during condensation. In the present work, the capabilities of the Nelumbo droplet ejection coatings technology currently used in commercial heat exchangers are explored and optimized for materials and conditions relevant to steam condensers. Specifically, this includes (1) adapting and optimizing the procedures and chemistries to deposit droplet ejecting coatings on materials used in the steam condenser, (2) testing of the heat transfer, durability, and fouling of the fabricated coatings under a variety of steam condenser relevant conditions, and (3) modeling of the impact of droplet dynamics and interfacial properties on heat transfer in steam condensers. We experimentally demonstrated that at low supersaturation conditions (S~1.02), developed superhydrophobic nanostructured surface gives a 40% higher peak heat transfer flux and a 17% higher peak overall heat transfer coefficient (U) with droplet ejection mechanism compared to the dropwise condensation mechanism on the same nanostructured surface. Though the experimentally observed droplet ejection mechanism was short-lived (~3 min) due to the limitation of the chiller to maintain a constant supersaturation condition in fabricated steam condenser. And large variations in water inlet temperature (+ to - 2 degrees C) caused flooding of nanostructure (Wenzel state) at higher supersaturation (S > or = 1.12). This is an important finding because typical supersaturation levels in field operation are over 1.8 and as such, either the flooding potential for these materials should be improved or operation at lower supersaturation may be required to maximize heat transfer efficiency. If supersaturation conditions can be maintained reliably in the steam condenser in addition to droplet ejection mechanism during condensation, this could provide a potential 2% reduction in water flow rate which equates to a savings of over 3900 gallons of water per minute for a 500 MW steam turbine and over $0.3MM savings annually given a 0.02 cent marginal water withdrawal cost. It is also worth noting that these savings are based on improvement of droplet ejection coatings over coatings capable of performing consistent dropwise mechanism in in-field surface condensers. Savings due to the droplet ejections coatings when compared to bare substrates could be much higher. Additionally, the present work provides the importance of steam condenser operating conditions and insights into the challenges in modeling the condensing droplet dynamics on surfaces.

20 FOSSIL-FUELED POWER PLANTS↗