SEARCH · Search NASA

Results for “time-resolved studies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Experimental and theoretical studies of time-averaged and time resolved rotor heat transfer

Efforts in support of the Space Shuttle Main Engine (SSME) structural durability program have concentrated on obtaining detailed time-averaged and time-resolved (or phase-locked) measurements on a full-scale rotating turbine both with and without cold gas injection and on theoretical studies designed to improve the prediction capability for these turbine flows. The experimental efforts have concentrated on use of the Garrett TFE 731-2 hp turbine. However, it has been possible to apply the theoretical efforts to predicting heat-flux distributions obtained for two additional turbines - i.e., (1) the Garrett low aspect ratio turbine (LART) and (2) the Teledyne 702 turbine. The experimental technique is the short duration, shock-tunnel approach, in which fast-response, thin-film resistance thermometers are used to measure surface temperature histories at prescribed locations on the turbine component parts. Heat-flux values are then inferred from the temperature histories by using standard data reduction procedures. The turbine being used is the Garrett TFE 731-2 hp stage, and both the nozzle guide vanes and the rotor blades are heavily instrumented with thin-film heat-flux gauges. Depending on how the data from a particular heat-flux gauge are recorded, one can get either time-resolved (or phase-locked) or time-averaged results. Both types of data are illustrated.

Dunn, M. G.↗

NASA NTRS1985

Time-resolved laser-induced fluorescence of selected even-parity 7p states of Xe I

Lifetimes and self-quenching rates have been measured for excited states of Xe I that were populated using simultaneous two-photon absorption. Lifetimes measured in this study are somewhat shorter than those measured using the broadband-excitation technique. Lifetimes reported here are all faster than 100 nsec. Deactivation rates are approximately 2 x 10 to the -10th cu cm/sec per mol.

Mcgee, T. J.↗

NASA NTRS1987

An investigation of stellar coronae with AXAF

Questions concerning the phenomenon of stellar coronae are discussed together with the physical parameters essential to model stellar coronae and the different AXAF instruments assigned for measurements of these parameters. As an illustration of what AXAF will be able to accomplish, three specific examples of studies by AXAF are described. These include coronal modeling for a bright X-ray source such as HR 1099, using spectra obtained by AXAF; time-resolved spectroscopy of AR Lacertae and YY Geminormum during their eclipses, to use the spectra for the identification and modeling of individual geometrical physical structures on these stars; and time-resolved spectroscopy during stellar flares to obtain high-resolution spectra which will make it possible to infer the changes in the flaring plasma temperatures as a function of time.

Linsky, Jeffrey L.↗

NASA NTRS1978

Temperature dependence of the rate constants for reactions of O/1D/ atoms with a number of halocarbons

Results are reported for an experimental study of the reactions of O(1D) with CCl4, CFCl3, CF2Cl2, CHFCl2, CHF2Cl, and CF2ClCFCl2 over the temperature range from 173 to 343 K, based on the time-resolved emission of O(1D) at 630 nm. The experiments involved photolysis of O3 by Nd-YAG laser pulses and measurements of 630-nm emission intensity in mixtures with He and the various halocarbons. Pseudo-first-order rate constants are derived from plots of the logarithms of the 630-nm emission intensities as a function of time for particular He/O3/halocarbon mixtures, and second-order rate constants are then obtained from plots of these pseudo-first-order rate constants as a function of halocarbon concentration at constant He and O3 concentrations. No temperature dependence of the second-order rate constants is observed over the range studied, within the precision of the measurements. It is found that the rate constants decrease as H is substituted for Cl in a halocarbon molecule and as F is substituted for H or Cl.

Davidson, J. A.↗

NASA NTRS1980

Ozone photolysis - Determination of the O/3P/ quantum yield at 266 nm

Direct production of O(3P) from the photodissociation of O3 at 266 nm has been observed by time-resolved resonance fluorescence following laser flash photolysis. The quantum yield for O(3P) production was determined to be 0.12 + or - 0.02 at this wavelength. This result confirms the qualitative observations of two previous photofragment studies and establishes an absolute value of the quantum yield for O(1D) production of 0.88. This value has been used as a basis for normalizing relative quantum yields in the fall-off region, and interpreting O(1D) kinetics studies.

Brock, J. C.↗

NASA NTRS1974

Shock-tube study of carbon monoxide dissociation kinetics

Carbon monoxide dissociation-rate data were obtained over the temperature range 5600-12,000 K. The experiments were conducted with undiluted CO to emphasize rate constants applicable to molecular gas systems. Data were obtained as time-resolved pressure measurements on the end wall of a shock tube and, in some cases, as emission histories of the C2 Swan system (0-0 band) behind incident shock waves. Results confirm the presence of C2 as an intermediate species in CO decomposition.

Hanson, R. K.↗

NASA NTRS1982

Picosecond flash spectroscopic studies on ultraviolet stabilizers and stabilized polymers

Spectroscopic and excited state decay kinetics are reported for monomeric and polymeric forms of ultraviolet stabilizers in the 2-(2'-hydroxyphenyl)-benzotriazole and 2-hydroxybenzophenone classes. For some of these molecules in various solvents at room temperature, (1) ground state absorption spectra, (2) emission spectra, (3) picosecond time-resolved transient absorption spectra, (4) ground state absorption recovery kinetics, (5) emission kinetics, and (6) transient absorption kinetics are reported. In the solid state at low temperatures, emission spectra and their temperature dependent kinetics up to approximately 200K as well as, in one case, the 12K excitation spectra of the observed dual emission are also reported.

Scott, G. W.↗

NASA NTRS1979

Experimental Studies of Radiative Base Heating of a Jovian Entry Model

To verify the validity of the theoretical predictions of Park on radiative base heating rates, two types of models are tested in the absence of ablation in shock tube flows which simulate the Jovian entry environments. The radiative fluxes are measured by pyroelectric radiometers imbedded in the models in a stream consisting of 10% hydrogen in a bath of either neon or argon. In addition, time-resolved photographs are taken to obtain information on the structure of base flows needed in Park's theory. The experimental data show that the radiative base heat fluxes are significant fractions of the radiative fluxes at the front stagnation point, the ratio being dependent upon Mach number and the configuration of the models. When the effects of the model geometry and Mach number are accounted for, the present experimental results agree with the theoretical predictions of Park.

Shirai, Hiroyuki↗

NASA NTRS1985

Methods for heat transfer and temperature field analysis of the insulated diesel phase 2 progress report

This report describes work done during Phase 2 of a 3 year program aimed at developing a comprehensive heat transfer and thermal analysis methodology for design analysis of insulated diesel engines. The overall program addresses all the key heat transfer issues: (1) spatially and time-resolved convective and radiative in-cylinder heat transfer, (2) steady-state conduction in the overall structure, and (3) cyclical and load/speed temperature transients in the engine structure. During Phase 2, radiation heat transfer model was developed, which accounts for soot formation and burn up. A methodology was developed for carrying out the multi-dimensional finite-element heat conduction calculations within the framework of thermodynamic cycle codes. Studies were carried out using the integrated methodology to address key issues in low heat rejection engines. A wide ranging design analysis matrix was covered, including a variety of insulation strategies, recovery devices and base engine configurations. A single cylinder Cummins engine was installed at Purdue University, and it was brought to a full operational status. The development of instrumentation was continued, concentrating on radiation heat flux detector, total heat flux probe, and accurate pressure-crank angle data acquisition.

Morel, T.↗

NASA NTRS1987

Rate constant for the reaction of atomic oxygen with phosphine at 298 K

The rate constant for the reaction of atomic oxygen with phosphine has been measured at 298 K using flash photolysis combined with time-resolved detection of O(3P) via resonance fluorescence. Atomic oxygen was produced by flash photolysis of N2O or NO highly diluted in argon. The results were shown to be independent of (PH3), (O), total pressure and the source of O(3P). The mean value of all the experiments is k1 = (3.6 + or -0.8) x 10 to the -11th cu cm/s (1 sigma). Two previous measurements of k1 differed by more than an order of magnitude, and the results support the higher value obtained in a discharge flow-mass spectrometry study. A comparison with rate data for other atomic and free radical reactions with phosphine is presented, and the role of these reactions in the aeronomy or photochemistry of Jupiter and Saturn is briefly considered.

Stief, L. J.↗

NASA NTRSDate not supplied

Fluid-Thermal-Structural Interactions Induced by an Asymmetric Shock-Wave/Boundary-Layer Interaction in a Mach-6 Compression Corner

An experimental study is conducted of the fluid-thermal-structural interaction of a clamped compliant panel exposed to a three dimensional shock-wave/boundary-layer interaction (SWBLI) induced by a Mach-6 compression ramp with a spanwise nonuniform incoming boundary layer. The nonuniform boundary layer was produced by placing trips on one side of the upstream flat plate, resulting in largely turbulent flow on the tripped side and transitional flow on the untripped side. Measurements of the flowfield confirmed that the tripped boundary layer contained elevated levels of unsteadiness, and the SWBLI was observed to vary from attached to fully separated as the ramp angle was increased from 10◦ to 38◦; the separation region on the tripped side of the panel was noticeably smaller, showing the elevated turbulence levels of the tripped-side flow to remain relatively localized rather than diffusing across the whole model. Full-field, time-resolved panel deformations were measured using high-speed photogrammetry and the vibrational response at each compression angle was characterized. Although the measured modes conformed largely to those from classical clamped-plate theory, some skewing of the mode shapes was observed. IR thermography highlighted regions of the compliant region where elevated temperatures were likely to promote thermal softening effects to the transient panel response. The quasi-static deformation and stress field was used to characterize the internal stress factor of each mode and showed a meaningful relationship between transient panel response and stress contained within each mode: modes with antinodes lying in high-stress areas of the plate tended to exhibit increases in vibrational frequency and decreases in vibrational power, whereas the opposite was true for modes with antinodes in low-stress areas.

Spectral Proper Orthogonal Decomposition↗

NASA NTRS1975

Study of the performance of antennas in magnetized plasmas

The antenna studies were performed in a large magnetized plasma source, a schematic drawing of which is shown. The plasma diagnostics consist of a 70 GHz (4 mm) microwave interferometer for density measurements and of various Langmuir probes for spatially resolved measurements of t sub e, n sub e and the shape of the electron distribution function. All diagnostic data are time-resolved by sample-and-hold techniques so as to yield information about the plasma build-up, the steady-state discharge, and the plasma decay in the afterglow. Whistler waves are excited and detected with various antennas which are inserted into the center of the plasma column through one axial and two orthogonal radial ports. The antennas were tested for their proper dipole response and then calibrated in a known field geometry in air. For the electric dipole, a parallel plate capacitor field was used; the magnetic loop is calibrated in the near-zone field of a long linear conductor of known radio frequency current distribution. Results are presented and discussed.

Stenzel, R. L.↗

NASA NTRS1981

Combined single-pulse holography and time-resolved laser schlieren for flow visualization

A pulsed ruby laser and continuous-wave argon ion laser were used in a combined setup at the Langley Expansion Tube for single pulse holography and time resolved laser schlieren with a common optical axis. The systems can be operated simultaneously for a single run. For a single frame, the pulsed holographic setup offers the options of shadowgraph, Schlieren, and interferometry from the reconstructed hologram as well as the advantage of post-run sensitivity adjustments. For flow establishment studies the time resolved laser Schlieren provides visualization of the flow field every 12.5 microns for up to 80 frames with an exposure time per frame of 5.4 microns.

Burner, A. W.↗

NASA NTRS1981

Time-resolved spectroscopy of the Mercury 6 3P1 state

The time-resolved fluorescence was observed from the Hg 6 3P1 state under the influence of the earth's magnetic field and with applied fields of up to 14 G. Modulation of the fluorescence decay signal was observed as a function of both time and space and can be interpreted in terms of a classical precession of the excited atom about the magnetic field or as quantum beats resulting from interference between coherently populated Zeeman sublevels. This modulation was studied for each of the five resolvable components of the hyperfine structure separately. The fluorescence from the even isotopes was determined to be almost completely modulated while the fluorescence from the odd isotopes was only partially modulated. The frequency of modulation of the fluorescence from the mercury-202 isotope was observed as a function of the applied magnetic field and a value for the Lande factor of 1.46 + or - 0.03 was obtained. This is within experimental error of the accepted value of 1.486. In addition, the frequency of modulation as a function of applied magnetic field was determined for each of the three resolvable components with more than one contributing isotopic hyperfine line. An investigation of the effect of radiation trapping on the degree modulation was also made.

Halstead, J. A.↗

NASA NTRS1986

Feasibility experiments on time-resolved fluorosensing applied to oil slicks

The introduction of time resolved observations can provide a very penetrating tool in the practice of laser fluorosensing. The investigations have demonstrated a relevance of multispectral, time resolved analysis for oil fingerprinting. By comparative studies on a variety of crude oils and their most significant fractions, it was found that the process of time decay in a composite oil is characterized by a few steps, which are associated with specific components in the medium light range. The average decay times of these pure fractions are markedly differentiated as to absolute values and spectral spread; as a consequence, the corresponding parameters in the resultant crude are quite sensitive to the particular mixture of these components. Measurements of the time response give then a finer discrimination between oil classes, depending on the relative content of certain fractions. Experiments were pursued with an improved fluorosensor facility, in order to test the application of time resolved fluorosensing to remote samples on water.

Camagni, P.↗

NASA NTRS1986

A fast data acquisition system for the study of transient events by high repetition rate time-of-flight mass spectrometry

Recent advances in commercially available data acquisition electronics embodying high speed A/D conversion coupled to increased memory storage have now made practical (at least within time intervals of a third of a millisecond or more) the capturing of all of the data generated by a high repetition rate time-of-flight mass spectrometer producing complete spectra every 25 to 35 microseconds. Such a system was assembled and interfaced with a personal computer for control and management of data. The applications are described for recording time-resolved spectra of individual vapor plumes induced from the pulsed-laser heating of material. Each laser pulse triggers the system to generate automatically a 3-dimensional (3-D) presentation of the time-resolved spectra with m/z labeling of the major mass peaks, plus an intensity versus time display of both the laser pulse and the resulting vapor pulse. The software also permits storing of data and its presentation in various additional forms.

Lincoln, K. A.↗

NASA NTRS1988

Synopsis of a computer program designed to interface a personal computer with the fast data acquisition system of a time-of-flight mass spectrometer

Briefly described are the essential features of a computer program designed to interface a personal computer with the fast, digital data acquisition system of a time-of-flight mass spectrometer. The instrumentation was developed to provide a time-resolved analysis of individual vapor pulses produced by the incidence of a pulsed laser beam on an ablative material. The high repetition rate spectrometer coupled to a fast transient recorder captures complete mass spectra every 20 to 35 microsecs, thereby providing the time resolution needed for the study of this sort of transient event. The program enables the computer to record the large amount of data generated by the system in short time intervals, and it provides the operator the immediate option of presenting the spectral data in several different formats. Furthermore, the system does this with a high degree of automation, including the tasks of mass labeling the spectra and logging pertinent instrumental parameters.

Bechtel, R. D.↗

NASA NTRS1988

Multichannel boxcar-averaged measurements of plasma parameters made using a digital storage scope

A technique for rapidly acquiring time-resolved, ensemble-averaged Langmuir probe characteristics is presented. Fifty probe characteristics are acquired using a digital storage oscilloscope in the time it would take to acquire a one-probe characteristic using a single-channel boxcar averager. A single Langmuir probe is used, and the probe bias is swept quite slowly, so that the probe is always in equilibrium with the plasma. A method for the automatic extraction of electron temperature, electron density, and the plasma potential from the acquired probe characteristics is described. This technique for acquisition and analysis is applied to the study of plasma decay and the effects of rf excitation in a pulsed, strongly magnetized plasma.

Sheridan, T. E.↗