SEARCH · Search NASA

Results for “toroidal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Assembly of the MOLLER Toroidal Magnets at Jefferson Lab

The MOLLER experiment at the Thomas Jefferson National Accelerator Facility (JLab) aims to precisely measure the weak interaction between electrons. This experiment leverages the 12 GeV electron beam and will run for three years. A crucial component of MOLLER is a system of five uniquely shaped water-cooled toroidal magnets. These magnets, possessing seven-fold symmetry, are designed to focus particles by separating electrons scattered off hydrogen in a liquid hydrogen target. The five magnets separate electrons scattered off electrons (Møller scattering) and protons (elastic e-p scattering) within target into approximately circular rings at the detector. Here, this paper presents the assembly process for these five toroidal magnets, detailing critical steps including epoxy application, pin insertion, soldering and brazing, coil assembly, and alignment, all performed to meet stringent magnet specifications. Additionally, it discusses challenges encountered during construction and highlights lessons learned, offering insights for future magnet development projects.

Lamont, Joseph [Thomas Jefferson National Accelera↗

DOE OSTI2025

Toroidal Alfven Wave Coupling (Nonlinear Wave-Wave Interactions) on DIII-D

Connect DIII-D physics with space plasma phenomena. In this case of using the toroidal Alfvén eigenmodes and frequency-chirping Reversed-Shear Alfvén eignmodes in DIII-D, we will document how the nonlinear interactions among dipolar Kinetic Alfvén Wave eigenmodes in space plasmas may determine saturation levels of these fluctuations. We seek evidence of nonlinear energy transfer and wave-wave coupling during 3-wave interactions mediated by a much lower-frequency mode. In FY2019, we found evidence of nonlinear “wave-wave” interactions in 175 relevant shots of archival DIII-D data. Toroidal mode number was identified and spectrograms were produced from each shot’s Mirnov coil data. Bispectral analysis was performed using a preliminary version of a new user friendly code derived from a 1995 M.S. thesis at WVU. These results formed a part of a May 2019 M.S. thesis at WVU.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Investigation of Anchor Link Magnetohydrodynamic Effects in the Toroidally Symmetric Lead-Lithium (TSLL) Blanket Concept

This paper presents a comprehensive study on the magnetohydrodynamic (MHD) flow in a slotted channel with a cylindrical anchor link, which is an imperative component of the toroidally symmetric lead-lithium (TSLL) blanket concept. Following the validation of the MHD solver implemented in COMSOL and a proposed subtraction approach to compute the anchor link pressure drop, the effects of computational domain size on the pressure drop and velocity distribution are examined. The results show that the pressure drop associated with the anchor link and the maximum flow velocity follow an asymptotic trend as the domain width increases, with wall-induced pressure drop being more dominant than that of the anchor link. The velocity distribution analysis revealed the formation of an internal boundary layer extending along the magnetic field direction, which is a unique feature of the investigated MHD flow. An estimation of the total MHD pressure drop associated with the array of anchor links under the TSLL blanket conditions suggests ~0.3 MPa, which is significantly lower than the recommended maximum allowable blanket pressure drop of 2 MPa. In conclusion, this work offers valuable insights into the anchor link–associated MHD phenomena and serves as a foundation for further development of the TSLL blanket concept for future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Instantaneous difference frequency locking observed during toroidicity-induced Alfvén eigenmode coupling in the DIII-D tokamak

In magnetic confinement fusion, toroidicity-induced Alfvén eigenmodes (TAEs) are well-studied, weakly stable solutions of the linearized ideal magnetohydrodynamic equations. Driven unstable by suprathermal populations of energetic particles, TAE pose a key vulnerability to the confinement of high-energy alpha particles generated by fusion reactions. Hence, it is paramount to understand TAE dynamics if a working reactor is to be realized. In this work, we detect and characterize signatures of nonstationary nonlinear coupling between TAE using a novel, time-resolved bispectral analysis; results are supported by analytic signal of band-passed data. Crucially, a stationary phase relationship between two TAE and a nascent low frequency fluctuation is observed precisely when the triple product of magnetic fluctuation amplitudes is enhanced. Local mode number and frequency spectrum, gleaned from beam-emission spectroscopy, corroborates simultaneous satisfaction of nonlinear matching conditions, and provides a tool to identify theorized pathways of energy transfer, e.g. TAE parametric instability.

bispectral analysis↗

DOE OSTI2024

All-in-one probe for exploring self-organized two-fluid equilibria in toroidal plasmas

This paper presents the development of an all-in-one probe to simultaneously measure all components of the generalized Ohm’s law in reversed-field pinch plasmas and tokamaks. The polyhedral configuration of the Mach probe is achieved through the specific arrangement, angle, and depth of the collimator channel apertures drilled into the surface of a hollow boron nitride cylinder encasing it. This probe includes a central Mach probe to assess the ion velocity field in three dimensions. Initial tests at the RELAX and Madison Symmetric Torus machines have confirmed the probe’s effectiveness, revealing an octahedron form similar to a tetrahedron. The probe seems to function correctly and is expected to facilitate the empirical validation of two-fluid equilibria at the periphery of toroidal plasmas.

Instruments & Instrumentation↗

DOE OSTI2024

Toroidal Alfvén mode instability driven by plasma current in low-density Ohmic plasmas of the spherical tori

Due to intrinsically low magnetic fields, at low density the drift speed of the current-carrying electrons in spherical tokamaks can exceed fraction of the Alfvén speed sufficient for the excitation of the Alfvén gap modes. A particular case of the toroidal mode, observed during minor disruptions in Ohmic shots on SUNIST [Liu et al., Phys. Plasmas 23, 120706 (2016)], is considered in the present communication. Due to the negligible effect of the electron pressure gradient, the growth rate scales linearly with the drift speed, with slope inversely proportional to electron thermal velocity. In the absence of continuum damping, the threshold value of the drift speed for TAE excitation is independent of electron temperature.

Marchenko, V. S. (ORCID:0000000261480533)↗

DOE OSTI2025

An implementation of a high-order generalized finite difference method for solving the time-harmonic cold plasma wave equation in toroidal geometry

A high-order physics-informed meshless finite difference numerical technique is introduced for solving the time-harmonic cold plasma wave equation in toroidal geometries, presenting a novel application of the generalized finite difference (GFD) method to plasma wave simulations. The algorithm employs an irregular distribution of computational points, with local point density informed by the shortest wavelength derived from the cold plasma dispersion relation. Numerical stability and robustness are addressed using regularization techniques. The algorithm, implemented for two spatial dimensions, solves for the wave electric field and is demonstrated to achieve convergence rates of $\mathcal{O}$($\mathcal{h}$ $\mathcal{P}$ )⁠. Verification tests reproduce plane wave solutions, and example simulations of ion cyclotron resonance heating and electron cyclotron resonance heating demonstrate its capability, approaching realistic tokamak plasma scenarios. This work contributes to laying a foundation for the GFD method to be used in more sophisticated, optimized, and physically realistic full-wave simulations in time-harmonic plasma wave research.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Efficient analysis of magnetic field line behavior in toroidal plasmas

The confinement of plasmas in tokamaks and stellarators depends on magnetic field lines lying in nested toroidal surfaces. The transition near the plasma edge away from the lines lying in magnetic surfaces defines properties of divertors. The transition in time defines properties of disruptions. Divertor design and disruption analyses require a detailed understanding of these transitions. The use of a Fourier transform coupled with a Gaussian window function allows far more information to be extracted about these transitions using far shorter field line integrations than can be obtained using traditional methods based on Poincaré plots. The physics of divertors and disruptions is reviewed to clarify why the type of information that can be gained from more efficient methods of analysis is of central importance to the fusion program based on magnetic confinement.

Boozer, Allen H. [Columbia Univ., New York, NY (Un↗

DOE OSTI2025

Simulations of the churning mode: Toroidally symmetric plasma convection and turbulence around the X-points in a snowflake divertor

Using a reduced MHD model, extended to include field-aligned thermal conduction, we present numerical simulations of the churning mode (CM): a toroidally symmetric, non-linear plasma vortex in the vicinity of the null points in a snowflake (SF) divertor [D. D. Ryutov et al., Phys. Scr. 89, 088002 (2014)]. Simulations are carried out across a range of inter-null separations, d xx ⁠, and inter-null orientations, θ⁠, primarily in conditions relevant to the MAST-U tokamak. We find that, when d xx is small, the CM induces additional transport across the X-points when β pm ≳8%, where β pm is the ratio of the plasma pressure in the null region to poloidal magnetic pressure at the midplane. This transport also increases approximately linearly as d xx is reduced. A diffusive model of this transport is shown to predict the total transport across the null points, where diffusion coefficients of up to ∼ 10 2 m 2 s −1 centered on a small region around the X-points are used. However, the CM also results in significant changes to the flux surfaces in the null region, which is not captured by this diffusive model. The changes in magnetic geometry mean the fractional exhaust power delivered to each divertor leg is highly sensitive to β pm ⁠, d xx ⁠, and θ⁠. For small values of θ⁠, the CM can induce a change in topology, redirecting exhaust power from a secondary divertor leg on the high field side to one on the low field side. Similar behavior is found in the fraction of exhaust power going to the inner and outer divertor. Such changes in the flux surfaces may not be captured by Grad–Shafranov solvers and so may be a source of error in the magnetic reconstruction of SF experiments. We consistently find that the fractional exhaust power going to a secondary divertor leg on the high field side is small, consistent with SF experiments.

Computer simulation↗

DOE OSTI2025

Simulations of plasma current induced by toroidal field ramping down on tokamaks

In tokamak experiments, the BT ramping down can drive off-axis and parallel inductive current. This approach leads to a decrease in q95 and an increase in normalized beta, βN. The off-axis inductive current also broadens the current profile. Typically, the 1.5D transport code is used to simulate the time evolution of the plasma current profile, which is based on the flux-surface-averaged Faraday’s law. The ONETWO code is one of those transport codes. However, this code cannot simulate the situation of the evolving toroidal field BT. This article proposes a new time-dependent model to take into account the BT ramping down situation. A modified formula of flux-surface-averaged Faraday’s law was derived to consider the effect of the BT ramping rate on the current evolution, and it was implemented in the ONETWO code. Then, the modified ONETWO code was used to simulate the BT ramping down experiment on DIII-D. The simulation result of the plasma current evolution with BT ramping down shows a broader current profile with smaller ohmic current induced by the poloidal field, compared to that without BT ramping down.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Impact of window temperature variations on ITER toroidal interferometer and polarimeter (TIP) measurements

Abstract The toroidal interferometer and polarimeter (TIP) is one of the primary electron density diagnostics on ITER. To meet measurement requirements over several thousand seconds, environmental factors such as changes in the window temperature, air temperature, and humidity, which can cause uncompensated phase drifts, must be minimized. This paper reports measurements of the phase shift induced by ZnSe and BaF₂ windows as their temperature is varied utilizing the TIP prototype. To accomplish these measurements, test pieces of BaF₂ and ZnSe are placed in a small oven that is located in one leg of the 10.59/5.22 micron two-color interferometer TIP prototype. The oven temperature was varied from room temperature to ∼90 °C, which is slightly higher than the expected window temperatures on ITER. The vibration compensated phase shifts measured for these two materials are dϕᵥ꜀ /dT/L = 0.0121 and −0.275 deg. /°C/cm −1 for BaF₂ and ZnSe, respectively. From these measurements, it was concluded that temperature variations of the environmental/secondary confinement barrier window and primary vacuum window have to be suppressed within approximately 1°C and 2°C, respectively, in order to passively meet the electron density measurement requirements in ITER.

Akiyama, T (ORCID:0000000198469795)↗

DOE OSTI2024

Toroidal injection angle dependence of EC assisted plasma initiation at DIII-D

An experimental scan of the electron cyclotron waves (EC) toroidal injection angle in plasma breakdown is performed at the DIII-D tokamak. The second harmonic, extraordinary mode EC is used for the study. The dependence of n e and T e on the EC injection angle cannot be conclusively drawn from this study due to the large error bars in the n e and T e measurements. On the other hand, high T e data points are observed in some discharges which can be explained by nonlinear heating. The D α emission measurement shows a clear relation between the breakdown time and the injection angle. An experimental investigation of the cause of the dependence of breakdown delay on the EC injection angle suggests that when the injection angle is oblique, the EC heating after the reflection at the inboard wall may become ineffective and cause the breakdown delay even when the EC heating before and directly upon injection remains effective. A preliminary run of the heat and transport balance code DYON indicates that the obtained dataset is suitable for a quantitative validation of EC absorption models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Counter-propagating toroidal Alfvén eigenmodes in tokamaks

Mechanisms of destabilization of toroidal Alfvén eigenmodes (TAEs) in tokamaks are analyzed with the aim to reveal those leading to modes propagating in the direction opposite to plasma current, i.e. counter-propagating modes (ctr-TAE). Plasmas with fast-ions sources [such as neutral beam injection (NBI), ion cyclotron resonance heating, fusion reactions] and without them (Ohmic discharges) are considered. A particular NSTX-U experiment with NBI, where co- and counter-propagating TAEs were observed simultaneously (Podestà et al 2018 Nucl. Fusion 58 082023), is considered. It is concluded that both types of TAEs occurred because their destabilization was caused by the velocity anisotropy of beam ions, which overrode effects of spatial inhomogeneity of these ions.

Alfvénic instabilities↗

DOE OSTI2025

Toroid Signal Processing Container with Redis Integration

This report presents the research, design, and implementation of a Toroid Signal Processing Container with Redis Integration, conducted during my internship assignment. The project focused on developing a modular signal processing sys- tem capable of performing baseline correction, droop compensation, and real- time data communication for beam diagnostic signals. Using Redis as a message broker and configuration manager, the system ensures modularity, scalability, and efficient inter-process communication. Signal correction algorithms, such as Asymmetric Least Squares (ALS) baseline smoothing and a numerical droop correction approach, were implemented and tested using Linac beam data. The results confirm that this system improves signal fidelity and supports real-time analysis requirements, offering valuable contributions to the field of beam instrumentation and data acquisition systems.

Bowers, Elliot [Cabrillo Coll.]↗

DOE OSTI2025

Dataset for "Theory of zonal flow generation and propagation in toroidal geometry"

Dataset and input files to generate figures in "Theory of zonal flow generation and propagation in toroidal geometry."

fusion↗

DOE OSTI2025

Toroid Signal Processing Container with Redis Integration

Bowers, Elliot [Cabrillo Coll.; Fermilab]↗

DOE OSTI2025

Radiative damping of toroidal Alfvén eigenmode in low-shear plasmas

Instabilities of Alfvén eigenmodes (AEs) are of significant concern because they can enhance the cross-field transport of fusion-born alpha particles beyond the neoclassical level in magnetic fusion plasmas. The threshold value of alpha-particle pressure for exciting AEs depends critically on the damping rate of AEs. The damping mechanisms include kinetic damping due to interactions with thermal particles, continuum damping due to AE frequency crossing Alfvén continuum, and radiative damping due to emitting kinetic Alfvén waves (KAWs). The radiative damping is substantial and can even prevail in high-temperature burning plasmas [1]. We revisit the radiative damping analytic theory for TAE in plasmas with low positive magnetic shear, considering TAE with an eigenfrequency near the bottom of TAE-gap and with poloidal harmonics of the same sign (even TAE). In contrast to earlier papers, we provide the damping calculations in real space rather than Fourier space. This approach is straightforward technically and more enlightening from a physics standpoint for benchmarking numerical calculations of radiative damping. The parametric dependence of the resulting damping rate agrees with that of Refs. [2-5], but it has a smaller numerical factor in front of it.

Alpha-particle driven instability↗

DOE OSTI2025

Electron transport in a tokamak scrape-off layer: impact of toroidal nonuniformities of divertor targets

An analysis of electron dynamics is carried out in the tokamak scrape-off layer (SOL) region. Small non-axisymmetric perturbations of the divertor target sheath potential affect electron drift orbits in the SOL and may lead to non-ambipolar electron radial transport. The resulting rates of electron convection, diffusion, and mobility are calculated analytically, and the analytic results are compared with direct numerical simulations of electron drift orbits. The proposed mechanism of non-ambipolar electron transport may be relevant to the sustainment of the SOL plasma quasi-neutrality in the ‘heuristic’ model of the SOL width (Eich et al 2011 Phys. Rev. Lett. 107 215001).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗