Search NASA⌕ Search

SEARCH · Search NASA

Results for “total cost of driving”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

The Effect of Mission Location on Mission Costs and Equivalent System Mass

Equivalent System Mass (ESM) is used by the Advanced Life Support (ALS) community to quantify mission costs of technologies for space applications (Drysdale et al, 1999, Levri et al, 2000). Mass is used as a cost measure because the mass of an object determines propulsion (acceleration) cost (i.e. amount of fuel needed), and costs relating to propulsion dominate mission cost. Mission location drives mission cost because acceleration is typically required to initiate and complete a change in location. Total mission costs may be reduced by minimizing the mass of materials that must be propelled to each distinct location. In order to minimize fuel requirements for missions beyond low-Earth orbit (LEO), the hardware and astronauts may not all go to the same location. For example, on a Lunar or Mars mission, some of the hardware or astronauts may stay in orbit while the rest of the hardware and astronauts descend to the planetary surface. In addition, there may be disposal of waste or used hardware at various mission locations to avoid propulsion of mass that is no longer needed in the mission. This paper demonstrates how using location factors in the calculation of ESM can account for the effects of various acceleration events and can improve the accuracy and value of the ESM metric to mission planners. Even a mission with one location can benefit from location factor analysis if the alternative technologies under consideration consume resources at different rates. For example, a mission that regenerates resources will have a relatively constant mass compared to one that uses consumables and vents/discards mass along the way. This paper shows examples of how location factors can affect ESM calculations and how the inclusion of location factors can change the relative value of technologies being considered for development.

Fisher, John W.↗
DOE OSTI2021

Comparing total cost of ownership of battery electric vehicles and internal combustion engine vehicles

The technological advance of electrochemical energy storage and the electric powertrain has led to rapid growth in the deployment of electric vehicles. The high cost and the added weight of the batteries have limited the size (energy storage capacity) and, therefore, the driving range of these vehicles. However, consumers are steadily purchasing these vehicles because of the fast acceleration, quiet ride, and high energy efficiency. The higher pack-to-wheel efficiency and the lower energy cost per mile, as well as the lower expense for maintenance and repair, translate to operating savings over conventional vehicles. Here we compare battery electric vehicles with internal combustion engine vehicles based on the total cost of ownership. It is seen that the higher initial cost of electric vehicles can be recovered in as little as 5 years. This is especially true for electric vehicles with shorter driving ranges. Specifically, a vehicle with an electric driving range under 200 miles may achieve cost parity with an equivalent internal combustion engine vehicle in 8 years or less.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

SECARB-USA: Needs Assessment Framework for Storage Complexes (Task 2.1.b)

A team of SECARB storage experts examined 63 formations at 39 sites that were selected to represent the range of diversity of newly assessed, as well as well-advanced, storage prospects in the SECARB region. We inventoried the data needs triggered by the requirements to obtain a Class VI UIC storage permit, the data needs that results from the requirement to create geocellular fluid flow models to support that permit, and by pragmatic and best practice inputs such as public acceptance, regulatory readiness, and pore space leasing. We anchored both the needs inventory and the processes for and cost of meeting the needs with data from 9 sites in in the SECARB area that have advanced far in characterization. Results show that the total cost of characterization prior to obtaining a permit is convergent, because the permit and modeling requirements drive projects to obtain the same types of data for all cases. The high cost data that control cost are 1) drilling, coring, core-testing, logging, sampling and testing a characterization well and 2) collection of a 3-D seismic survey to map reservoir and confining system properties over the area of the plume or the area of elevated pressure. In 5 of our case study sites we determined that one or both of these costs could be avoided because the needs are met by available data.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1985

Evaluation of half wave induction motor drive for use in passenger vehicles

Research performed at the University of Missouri-Columbia to devise and design a lower cost inverter induction motor drive for electrical propulsion of passenger vehicles is described. A two phase inverter motor system is recommended. The new design is predicted to provide comparable vehicle performance, improved reliability and a cost advantage for a high production vehicle, decreased total rating of the power semiconductor switches, and a somewhat simpler control hardware compared to the conventional three phase bridge inverter motor drive system. The major disadvantages of the two phase inverter motor drive are that it is larger and more expensive than a three phase machine, the design of snubbers for the power leakage inductances produce higher transient voltages, and the torque pulsations are relatively large because of the necessity to limit the inverter switching frequency to achieve high efficiency.

Hoft, R. G.↗
DOE OSTI2024

Performance and Durability of Hybrid Fuel Cell Systems for Class-8 Long Haul Trucks

Hybrid fuel cell-battery configurations are investigated that overcome thermal management issues in fuel cell powertrains for heavy-duty Class 8 trucks. The battery is sized so that it has sufficient capacity to provide supplemental power and energy on a hill climb transient at end-of-life. A dynamic load sharing strategy is developed to distribute the power demand between the fuel cell system (FCS) and the energy storage system in a manner that optimizes their lifetimes. The FCS end-of-life is identified as the terminal point beyond which the stack cannot generate the rated power with target power density at 0.7 V and 40 °C ambient temperature. Reaching the target lifetime with a-Pt/C cathode catalyst in one hybrid configuration requires voltage clipping to 813 mV, idle power limited to 50 kW, catalyst overloading to 0.45 mg cm -2 total Pt in anode and cathode, and 44% active membrane area oversizing. The stack and FCS drive cycle efficiencies decrease by 4.2% and 5.4%, respectively, during the electrode lifetime. Further, the FCS performance, durability and cost are compared with the targets of 68% peak efficiency, 0.30 mg cm -2 total Pt loading, 2.5 kW/g PGM Pt group metal (PGM) loading, 750 mW cm -2 power density, 25,000-h lifetime and $80/kW cost.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRSDate not supplied

Examining the Trends in Financial Support Given to Science Teams for Data Analysis in Mission Proposals

Introduction: The goal of this summer internship research project was to analyze trends in financial support proposed for the science teams of planetary missions. The analysis focuses on the funding for Co-Investigators (Co-Is) to conduct research and/or data analysis needed to achieve the science objectives of the mission. The operational portion of the missions after launch (i.e., Phase E, including cruise and prime operations at the final destination) were examined since that is when the bulk of research is funded and conducted. The objectives of the project were to determine the average level of support for Co-Investigators, identify variation between mission competitions and over time, and determine the relationship between mission type and the amount of support requested. Methodology: This project was conducted using data from 90 proposals submitted to six mission competitions in the Discovery and New Frontiers programs. The level of support for Co-Is was determined by examining Work Breakdown Structure (WBS) 4 (Science Analysis) for Phase E, which was further subdivided into cruise and prime operations. This data represents a proxy rather than the actual funding Co-Is receive to perform research and data analysis because not every dollar in WBS 4 is spent on this activity. Therefore, the proxy obtained in this research represents an overestimate of the funds allocated to Co-Is for research and data analysis. Findings: Analysis shows that on average a Co-I receives approximately four full years of support spread across the entirety of Phase E for science analysis. The variation among proposed missions is less than expected given the variety of factors that are expected to drive this metric (length of mission, mission type, etc.). Additionally, the level of requested support for Co-Is has been remarkably consistent across every variable considered (by competition, over time, by mission type) over the six competitions and nearly 20 years spanned by this project. This remains true for cruise, primary operations, and all of Phase E. Conclusions: A remarkable amount of science is accomplished by the science teams of planetary missions. However, a surprisingly small amount of funding is requested to support the science analysis driving this productivity, both in terms of absolute magnitude of funding and as a portion of total mission cost. This suggests improvements are needed to refine the estimates of Co-I support and/or that Co-Is rely on other funding sources to conduct their research. Better estimates can be determined by engaging directly with Co-Is and NASA centers to obtain data as well as finding other data sources. Additionally, NASA could consider mandating improved reporting of requested funding levels in mission competitions.

E Murray↗
NASA NTRS2009

Concepts for Life Cycle Cost Control Required to Achieve Space Transportation Affordability and Sustainability

Cost control must be implemented through the establishment of requirements and controlled continually by managing to these requirements. Cost control of the non-recurring side of life cycle cost has traditionally been implemented in both commercial and government programs. The government uses the budget process to implement this control. The commercial approach is to use a similar process of allocating the non-recurring cost to major elements of the program. This type of control generally manages through a work breakdown structure (WBS) by defining the major elements of the program. If the cost control is to be applied across the entire program life cycle cost (LCC), the approach must be addressed very differently. A functional breakdown structure (FBS) is defined and recommended. Use of a FBS provides the visibifity to allow the choice of an integrated solution reducing the cost of providing many different elements of like function. The different functional solutions that drive the hardware logistics, quantity of documentation, operational labor, reliability and maintainability balance, and total integration of the entire system from DDT&E through the life of the program must be fully defined, compared, and final decisions made among these competing solutions. The major drivers of recurring cost have been identified and are presented and discussed. The LCC requirements must be established and flowed down to provide control of LCC. This LCC control will require a structured rigid process similar to the one traditionally used to control weight/performance for space transportation systems throughout the entire program. It has been demonstrated over the last 30 years that without a firm requirement and methodically structured cost control, it is unlikely that affordable and sustainable space transportation system LCC will be achieved.

Rhodes, Russel E.↗
DOE OSTI2025

Low Cost High-Performance HRE-Free 3-in-1 Electric Drive Unit

The project team completed work to expand upon American Axle & Manufacturing’s (AAM) baseline technology and develop a high-speed, AC induction electric drive unit (EDU) with total direct-oil-cooling and integrated power electronics. The project accelerated advancements in EDU technology by allowing AAM to build upon the progress made in developing the underlying baseline technologies. The following seven improvements to AAM’s baseline technology were implemented in this research and development program: 1) Increased speed (30k RPM) AC induction motor, 2) Silver-sintering of discrete silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFET) to heat sinks, 3) Electrically insulated rotor bars, 4) Optimized lamination steel, 5) EDU-integrated 650VDC inverter package, 6) Over-molded stator with molded liners, and 7) 650VDC power-dense stator design. The successful development of the technology resulted in a meaningful cost reduction for EDU systems in the market. Coupled with falling battery system costs, lower EDU costs will likely accelerate the market acceptance and related production scaling of battery electric vehicles. The objective of this project was to research, develop, and test a Heavy Rare Earth (HRE)-free 3-In-1 electric drive unit (EDU) that has class leading power density and cost. The key technologies to be developed were anticipated to meet or exceed the Department of Energy (DOE) targets of a cost ≤ $\$$7/kilowatt (kW), power density ≥ 12 kW/liter, and operating voltage ≥ 600 VDC.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS

The Marine Algae Industrialization Consortium (MAGIC) was formed to address pressing challenges in the commercialization of microalgae as a source of biofuel. The “Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS” project formally addressed two US Department of Energy Bioenergy Technologies Office (BETO) goals: (1) Model the sustainable supply of 1 million metric tonnes ash free dry weight (AFDW) cultivated algal biomass and (2) Demonstrate valuable co-products produced along with biofuel intermediates to increase value of algal biomass by 30%. To achieve these goals, the project demonstrated and validated high-value co-products to drive down the cost of biofuel by increasing the value of algae “co-products” towards increasing the selling price of total algae biomass as one of the key drivers of economics and adoption. This was accomplished through five core, interdependent tasks including: (1) strain selection to identify and deliver strains for mass culture, (2) mass culture using a hybrid cultivation system and following key operating parameters for downstream applications to provide algae feedstock, (3) recovery and conversion to evaluate two alternative methods to separate dry algae biomass into oil and residuals for downstream testing, (4) product assessment to determine biofuel, aquafeed or poultry feed product efficacy using algae biomass fractions as well as to provide critical performance data for valuation and (5) commercialization to use technoeconomic and life cycle assessments (TEA/LCA) as iterative design and assessment tools including consideration of target markets, competitors, and distribution channels to guide product assessment, development and valuation. A total of 46 peer-review publications, many open-access, provide detail of much of the work carried out and the results of the tasks. Additional reports and presentations provide other technical and public engagement material. At a high level, using a variety of approaches, more than 1000 marine microalgae strains were evaluated to ultimately identify the seven winners that were down-selected to be grown in mass culture. Strain selection demonstrated that there were no ‘super strains’ and that each candidate had strengths and limitations for specific products, growth conditions or operational considerations. Mass culture growth of these seven strains at >5000 L / 29 m 2 scale found that four them were suitable for product assessment. More than 250 kg of biomass was produced across hundreds of pond runs along with thousands of cultivation entries on the growth and biomass characteristics as well as environmental parameters. In the process, dozens of standard operating procedures were generated as was custom software to process and analyze cultivation data. Recovery and conversion of algae biomass demonstrated that a hexane solvent based extraction protocol was most effective at recovering oil (biocrude) from algae and four strains were processed to produce oil and lipid extracted algae (residuals) for downstream testing. Membrane-based oil separation was less successful, but may still be applicable to other commercial applications in the future. Product testing demonstrated that algae biocrude is of high quality and hydrotreating generated numerous fractions of high quality composition for fuel and lubricate based applications. Aquafeed studies performed at a variety of scales showed that both whole and defatted (lipid extracted algae) microalgae were suitable as a feed ingredient, but that the specifics of the fed animal and biochemical composition of the algae are critical factors when determining formulation. Similarly, poultry studies on whole and defatted microalgae generally showed positive outcomes on animal growth and health, with some microalgae providing enhanced nutritional composition of the animal product. Economic and life cycle assessments covered a wide range of possible commercialization and sustainability scenarios. Replacement value, improved product value added, consumer values marketing added valuation and improved animal health were considered as alternatives for microalgae valuation. Using the open pond system, algae productivity was identified as the key driver of commercialization economics, but combination of co-products (e.g. animal feed) with biofuel production substantially increased the total selling price of algae. Modeled microalgae selling price exceeded $\$$1500/tonne and could generate competitive biofuel selling prices below $\$$5 gallon gas equivalents using realistic algal productivities. Short (process scale) and longer (decadal trends) sustainability assessments show that marine microalgae can enhance the sustainability of energy production and lead to other realized benefits in water, fertilizer and land use for other sectors (e.g. agriculture). This project successfully demonstrated all of the components of an end-to-end process from mass microalgae cultivation and dewatering, to recovery and conversion of algae biomass components, to final product demonstration and process valuation; the combined results provide a framework for future commercialization of algae based biofuels.

09 BIOMASS FUELS↗
DOE OSTI2020

Range cost-effectiveness of plug-in electric vehicle for heterogeneous consumers: An expanded total ownership cost approach

Plug-in electric vehicles (PEV) appears to have sales momentum in major personal vehicle markets but are still at the early market stage. Opportunities to accelerate PEV adoption can be discovered through comprehensive total cost of ownership (TCO) analysis. Understanding the cost-effective electric ranges of PEVs for consumers, manufacturers, and the society is critical for any discussion of PEV mass markets. This study expanded the traditional TCO approach by (1) fully considering heterogeneous consumer driving patterns, (2) quantifying the charging inconvenience and range anxiety cost of battery-electric vehicles (BEVs), and (3) monetizing both tangible and intangible PEV policies. Uncertainties were handled through Monte Carlo simulation. The results suggest that BEVs with an electric range of 250–350 km have the lowest TCO in cities with government-enacted purchase limitations, and internal combustion engine vehicles (ICEVs) have the lowest TCO in cities without purchase limitations, even when considering PEV subsidies. The lowest TCO for some consumer groups is obtained by BEVs with an electric range of 400–450 km, especially in northern China, where the weather is colder. The cost-effective all-electric range for BEVs in each city in 2025 will decrease due to improved battery performance in cold environments and an expanded charging infrastructure. Finally, based on TCO, plug-in hybrid electric vehicles (PHEVs) are currently more suitable for drivers with a high average daily mileage or a large mileage variance. However, by 2025, BEVs with a long driving range may become a more cost-effective choice for these drivers.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Future Projections of Lifecycle Cost and Greenhouse Gas Emissions of Light-Duty Vehicles

Vehicles with electrified powertrains carry the promise of significant reductions in greenhouse gas (GHG) emissions from a lifecycle analysis (LCA) standpoint compared to conventional internal combustion engine (CICE) vehicles. However, trade-offs exist between different types of electrified powertrains in terms of cost, consumer acceptance, and GHG reduction efficacy for different operating conditions. The open-source tool CarGHG was developed with an aim to enable the exploration of a plethora of parametric study scenarios, including the cost of electrification technologies, different driving patterns and charging habits, and the cost and carbon intensity of electricity and fuel blends. This paper introduces the framework of CarGHG, then showcases total cost of ownership (TCO) and LCA GHG results for select models of light-duty vehicles. Another capability of CarGHG, which is the ability to estimate the performance of “virtual” vehicle models (perceived vehicle design specifications not yet on the market), is utilized to explore future scenarios of electrification and low-carbon fuel blends for Small Sports Utility Vehicles (SUVs), a popular light-duty vehicle segment in North America. With opportunities, but also uncertainties, in future scenarios, it is likely wise to continue pursuing multiple ways towards the reduction of LCA GHG.

Hamza, Karim↗
NASA NTRS1992

Exodus: Prime Mover

The Exodus Prime Mover is an overnight package delivery aircraft designed to serve the Northern Hemisphere of Aeroworld. The preliminary design goals originated from the desire to produce a large profit. The two main driving forces throughout the design process were first to reduce the construction man-hours by simplifying the aircraft design, thereby decreasing the total production cost of the aircraft. The second influential factor affecting the design was minimizing the fuel cost during cruise. The lowest fuel consumption occurs at a cruise velocity of 30 ft/s. Overall, it was necessary to balance the economic benefits with the performance characteristics in order to create a profitable product that meets all specified requirements and objectives.

Bauer, Nikkol↗
DOE OSTI2024

Measurement of Wind Loading on Heliostats at the Crescent Dunes Power Plant: An Overview

The cost of solar collectors constitutes almost one third of the total cost of a CSP plant. One of the ongoing challenges in the design of these collectors is wind loading on mirrors, support structures, and drives. A particular challenge is dynamic wind loading, caused by the turbulent wind flow. To date, the design of solar collector structures has relied on wind tunnel experiments and numerical simulations that do not entirely capture the dynamic effects observed at scale. The CSP industry has shown increased interest in validating the idealized assumptions with measurements obtained in operational settings to improve wind load assumptions and increase reliability and cost-efficiency of the collector design. Further, performance models need realistic assumptions about wind loading and its impact on optical performance. In a parabolic trough field campaign, NREL successfully collected a wealth of long-term, high-resolution wind and loads data [2], that are publicly available and that can be used for the above-mentioned purposes. Heliostats are impacted differently by wind than parabolic troughs, due to their different shape, size, and field layout. To study the impact of wind and turbulence on heliostats, we initiated another field campaign in an operational power- tower plant, Crescent Dunes, in Nevada, USA. In this work, we present an overview of the measurements, first results, and potential implications of wind driven loads on Heliostats.

concentrated solar power↗
NASA NTRS2017

Human Mars Ascent Configuration and Design Sensitivities

Human missions to Mars may utilize several small cabins where crew members could live for days up to a couple of weeks. At the end of a Mars surface mission the Mars Ascent Vehicle (MAV) crew cabin would carry the crew to their destination in orbit in a matter of hours or days. Other small cabins in support of a Mars mission would include pressurized rovers that allow crew members to travel great distances from their primary habitat on Mars while unconstrained by time limits of typical EVAs. An orbital crew taxi could allow for exploration of the moons of Mars with minimum impact to the primary Earth-Mars transportation systems. A common crew cabin design that can perform in each of these applications is desired and could reduce the overall mission cost. However, for the MAV, the crew cabin size and mass can have a large impact on vehicle design and performance. The total ascent vehicle mass drives performance requirements for the Mars descent systems and the Earth to Mars transportation elements. Minimizing MAV mass is a priority and minimizing the crew cabin size and mass is one way to do that. This paper explores the benefits and impacts of using a common crew cabin design for the MAV. Results of a MAV configuration trade study will be presented along with mass and performance estimates for the selected design.

Polsgrove, Tara P.↗
DOE OSTI2023

Wind Loading on Parabolic Trough Collectors: Wind and Structural Loads Measurements at an Operational Powerplant

Concentrated Solar Power (CSP) is a promising method for using solar power for electricity generation with thermal energy storage for industrial applications. Solar collectors constitute almost 1/3 of the total cost of the power plant. One of the primary drivers of unrealiability of these collectors is wind-driven loading of mirrors, support structures, and drives. To date, the design of the solar collector structures has relied on data from wind tunnels that do not adequately capture the dynamic effects observed at scale. NREL initiated a field measurement campaign at the operational Nevada Solar One (NSO) parabolic trough powerplant. At this plant, parabolic trough solar collectors track the sun from east to west in the course of a day and face varying wind loads depending on the wind properties and the angle of the troughs. The aim of the project is a detailed characterization of prevailing wind and turbulence conditions and resulting operational loads on parabolic troughs, providing insights into structural dynamic response, and generating a comprehensive wind-loading dataset for validating simulations of wind loading on collector structures. The measurements at NSO consist of sonic anemometers on masts at different heights to characterize the incoming flow and conditions at four trough rows at the edge of the trough field. In addition, a Doppler Lidar scans the horizontal plane above the troughs. The wind measurements at NSO have been continuously collecting data since October 2021 and are combined with structural load measurements that started in November 2022. The load measurements were installed on the same four outermost trough rows and include support structure bending moments, drive torque moments, dynamic accelerations of the spaceframe, mirror displacement, and tilt angles. Measurements are planned to continue until May 2023, providing a first-of-a-kind, high-resolution multi-month dataset of combined wind and load measurements. In this presentation, we show first results of the measurement campaign. Based on the measurements, we identified three main factors altering the flow over the parabolic troughs: Wind speed, wind direction, and the angle of the parabolic troughs. Most interactions between incoming wind and the trough field are observed when the wind blows perpendicular to the trough rows. In this case, the first rows experience the highest wind speed and block the downwind rows, creating conditions with decreased wind speed and enhanced turbulence within the trough field. Also, turbulent length scales are smaller after the first row. This leads to the highest static loads (bending and torque moments) at the first row but potentially increased dynamic loads within the field. We illustrate our findings with case studies focused on different wind conditions and will present fatigue analysis to highlight the impact of wind-driven loads on collector structures.

CSP collectors↗
NASA NTRS1980

Solar total energy-large scale experiment, Shenandoah, Georgia

The design and development of a 7 meter diameter parabolic dish solar collector are discussed. Each of the four main subsystems of the collector: (1) reflector, (2) mount and drives, (3) receiver and (4) the controls, is discussed briefly with the major emphasis on the receiver design. To minimize development risks and production costs, a dish design based on use of stamped aluminum petals (sectors) was chosen. This design is similar to the design of a communication antenna already commercially produced. The reflective surface of the petals has a total reflectance of .86 and a specularity (dispersion) of 8 mrd. This performance is obtained by mechanical polishing and chemical brightening of the petal surface, followed by application of a clear RTV silicone protective coating. Selection of the material and weather proofing coated are discussed. Results from performance tests on an engineering development dish collector are presented and compared with pretest predictions.

Hensley, W. R.↗
DOE OSTI2022

A Comprehensive Approach towards Multi-Objective EMI Filter Design Optimization in High-Frequency SiC-Based Motor Drives

With rapid penetration of high-frequency, highdensity power electronics into the industry, controlling the system generated EMI becomes one of the major design challenges. Designing practical optimized EMI filters require simultaneous consideration of multiple aspects - including electromagnetic couplings, magnetic materials, practical component parasitics and their impacts at high-frequencies, and also the overall manufacturing costs. The multi-dimensional nature of the problem often results in overcompensated designs that hurt the system efficiency and power density. This paper focuses on a comprehensive design platform (developed in MATLAB) towards designing high-density, optimized, highly efficient EMI filters by analyzing the generated noise spectrum and evaluating a vast array of potential solutions before outputting an optimized filter solution. The proposed tool includes database-based component selection, optimal topology selection, multistage filter design, overall optimization for volume, mass, cost and total loss. The proposed filter has been thoroughly evaluated in a PSIM simulation environment emulating the hardware in CRD300DA12EXM3, a 300kW three-phase inverter from Wolfspeed with an RL load representing a motor drive application. Furthermore, a 20kHz switching frequency is chosen and impacts of the motor high-frequency characteristics on the generated EMI noise spectrum of the overall system have been analyzed.

42 ENGINEERING↗
DOE OSTI2020

Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps

As wind turbine blades continue to scale in length and total mass, the acceptability of traditional approaches for the engineering of processes to build these products has reached a limit. The continued need to reduce the levelized cost of energy (LCOE) drives manufacturing cycle times lower and the net mass of critical components challenges even the most experienced fabricators to meet the quality requirements for safe operating performance over the 25-year design life of the blade. In trying to reduce cycle time for key components of wind turbines, manufacturers discovered occasional buckling of fibers in wind turbine blade spar caps. The cause of the buckling was unknown. The goal of this project was to show that a comprehensive simulation, which considered all of the physics of the VARTM process, could identify the cause of the fiber buckling in spar caps that has been observed during the manufacturing process. Ultimately, the simulation determined the manufacturing process and parameters could lead to significant compressive stresses in the fibers eventually causing buckling. Simulation results suggest that the stress introduced from friction is the largest source of compressive stress in the fibers, the stress from the weight of gravity is significant but secondary, and the compressive stress from cure shrinkage does not play a significant role in the buckling of fibers. This report provides details of the testing and simulation methodology used to identify the cause of the fiber buckling.

17 WIND ENERGY↗