Search NASA⌕ Search

SEARCH · Search NASA

Results for “variable speed limit”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Design Guide for Pitch-Up Evaluation and Investigation at High Subsonic Speeds of Possible Limitations Due to Wing-Aspect-Ratio Variations

A design guide is suggested as a basis for indicating combinations of airplane design variables for which the possibilities of pitch-up are minimized for tail-behind-wing and tailless airplane configurations. The guide specifies wing plan forms that would be expected to show increased tail-off stability with increasing lift and plan forms that show decreased tail-off stability with increasing lift. Boundaries indicating tail-behind-wing positions that should be considered along with given tail-off characteristics also are suggested. An investigation of one possible limitation of the guide with respect to the effects of wing-aspect-ratio variations on the contribution to stability of a high tail has been made in the Langley high-speed 7- by 10-foot tunnel through a Mach number range from 0.60 to 0.92. The measured pitching-moment characteristics were found to be consistent with those of the design guide through the lift range for aspect ratios from 3.0 to 2.0. However, a configuration with an aspect ratio of 1.55 failed t o provide the predicted pitch-up warning characterized by sharply increasing stability at the high lifts following the initial stall before pitching up. Thus, it appears that the design guide presented herein might not be applicable when the wing aspect ratios lower than about 2.0.

Spreemann, Kenneth P.↗
DOE OSTI2024

Modifications to the JET Shattered Pellet Injector to Optimize Disruption Mitigation Experiments for Supporting ITER’s DMS Design

Shattered pellet injection (SPI) experiments on Joint European Torus (JET) are an important element in determining the physics basis for mitigating disruptions in ITER. Here, the initial design of the JET SPI system included three barrels to produce pellets with diameters of 4.5, 8.1, and 12.5 mm. The variability of the pellet speed by operating with and without a mechanical punch was limited and led to poor pellet integrity, so the mechanical punch was removed. Fragment size distribution is a function of pellet speed and the desire to change the resulting fragment size distribution was not originally a requirement. After the first set of SPI experiments on JET, different pellet sizes were considered to enable dual injection experiments with identical pellet diameters. It was also determined that speed control is necessary to improve experimental repeatability and to determine how the fragment size distribution impacts mitigation performance. Two barrels were fabricated to form pellets of 10 mm diameter and a third to form an 8.1 mm diameter pellet. New propellant valves were also fabricated and characterized to improve repeatability and overall performance. To have fine control of pellet speed, inserts to reduce the breech volume were fabricated and installed. Laboratory testing was conducted to ensure pellet release and provide a comparison of propellant gas delivered versus pellet speeds for a range of pellet types and mixtures. This article will also discuss how lessons learned from the JET SPI modifications can be applied to other SPI systems, such as the ITER SPI system, as controlling pellet release with the least amount of propellant gas is essential for optimal SPI effectiveness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

Coaxial Rotor CFD Validation and ML Surrogate Model Generation

A fixed-pitch speed-controlled coaxial rotor system was tested in the NASA Langley Transonic Dynamics Tunnel in September 2022. The rotors have a diameter of 1.35 meters and an inter-rotor spacing of 25% of the diameter. Though this test was focused on the NASA New Frontiers Dragonfly mission, the resulting dataset is relevant to a wide array of applications of multirotor vehicles, especially those using fixed-pitch variable-speed rotors. Most notably beyond Dragonfly, perhaps, is the application of coaxial rotor pair configurations for eVTOL and Urban Air Mobility (UAM) aircraft. This work provides a thorough CFD validation study quantifying coaxial rotor performance estimation with accuracy on order 5-10% using an efficient hybrid BEMT-URANS flow solver over a wide range of operating conditions. This accuracy was achieved using novel approaches for the construction of both the C81 airfoil performance lookup tables and the BEMT rotor model. These novel approaches are combined with advanced scripting to further accelerate the commercial off-the-shelf CFD solver on GPU accelerated machines. Finally, the development of machine learning surrogate models is presented to produce highly efficient and accurate rotor performance predictions for fixed-pitch variable-speed multirotor aircraft over the complete flight regime including scout, cruise, climb, descent, as well as limiting cases of vortex-ring and windmill-brake states.

Coaxial↗
NASA NTRS1977

Ceramics for the advanced automotive gas turbine engine: A look at a single shaft design

The results of a preliminary analysis of a single shaft regenerative design with a single stage radial turbine are presented to show the fuel economy that can be achieved at high turbine inlet temperatures, with this particular advanced design, if the turbine tip speed and regenerator inlet temperature are not limited. The engine size was 100 hp for application to a 3500 lb auto. The fuel economy was analyzed by coupling the engine to the auto through a continuously variable speed-ratio transmission and operating the system at constant turbine inlet temperature over the Composite Driving Cycle. The fuel was gasoline and the analysis was for a 85 F day. With a turbine inlet temperature of 2500 F the fuel economy was 26.2 mpg, an improvement of 18 percent over that of 22.3 mpg with a turbine inlet temperature of 1900 F. The turbine tip speed needed for best economy with the 2500 F engine was 2530 ft/sec. The regenerator temperature was approximately 2200 F at idle. Disk stresses were estimated for one single stage radial turbine and two two-stage radial-axial turbines and compared with maximum allowable stress curves estimated for a current ceramic material. Results show a need for higher Weibull Modulus, higher strength ceramics.

Nosek, S. M.↗
DOE OSTI2021

Real-World Driving Features for Identifying Intelligent Driver Model Parameters

Driver behavior models play a significant role in representing different driving styles and the associated relationships with traffic patterns and vehicle energy consumption in simulation studies. The models often serve as a proxy for baseline human driving when assessing energy-saving strategies that alter vehicle velocity. Such models are especially important in connectivity-enabled energy-saving strategy research because they can easily adapt to changing driving conditions like posted speed limits or change in traffic light state. While numerous driver models exist, parametric driver models provide the flexibility required to represent variability in real-world driving through different combinations of model parameters. These model parameters must be informed by a representative set of parameter values for the driver model to adequately represent a real-world driver. It stands to reason that determining the parameter values from real-world driving data would serve the purpose of representing a real-world driver. Although the published literature is replete with techniques and consequences of using real-world driving data to determine parameter values for parametric driver models, none have explored them in the context of using shorter driving features where the parameter values may change over the course of a single trip for the same driver. In this study we consider the “intelligent driver model” (IDM) as our driver behavior model and use real-world driving data from the Transportation Secure Data Center (TSDC) maintained at the National Renewable Energy Laboratory (NREL). The TSDC includes real-world travel data from across the United States, from which NREL has created a wide range of driving routes consisting of road features such as speed limits, stop locations, and turn locations. The real-world driving data are categorized into different driving regimes and extracted into driving features. The driving features are then used to calibrate the parameter values for the IDM. The distribution of the parameters and the relationships among them are reported. The insights obtained from this study enable judicious usage of IDM or similar parametric driver models to represent baseline human driver behavior in simulations.

27 ARPA - Advanced Research Projects Agency-Energy↗
DOE OSTI2021

Real-World Driving Features for Identifying Intelligent Driver Model Parameters: Preprint

Driver behavior models play a significant role in representing different driving styles and the associated relationships with traffic patterns and vehicle energy consumption in simulation studies. The models often serve as a proxy for baseline human driving when assessing energy-saving strategies that alter vehicle velocity. Such models are especially important in connectivity-enabled energy-saving strategy research because they can easily adapt to changing driving conditions like posted speed limits or change in traffic light state. While numerous driver models exist, parametric driver models provide the flexibility required to represent variability in real-world driving through different combinations of model parameters. These model parameters must be informed by a representative set of parameter values for the driver model to adequately represent a real-world driver. It stands to reason that determining the parameter values from real-world driving data would serve the purpose of representing a real-world driver. While the published literature is replete with techniques and consequences of using real-world driving data to determine parameter values for parametric driver models, none have explored them in the context of using shorter driving features where the parameter values may change over the course of a single trip for the same driver. In this study we consider the “Intelligent Driver Model” (IDM) as the driver behavior model to explore and real-world driving data from the Transportation Secure Data Center (TSDC) maintained at the National Renewable Energy Laboratory (NREL). The TSDC includes real-world travel data from across the United States, from which NREL has created a wide range of driving routes consisting of road features such as speed limits, stop locations and turn locations. The real-world driving data are categorized into different driving regimes and extracted into driving features. The driving features are then used to calibrate the parameter values for the IDM. The distribution of the parameters and the relationships among them are reported. The insights obtained from this study enable judicious usage of IDM or similar parametric driver models to represent baseline human driver behavior in simulations.

27 ARPA - Advanced Research Projects Agency-Energy↗
DOE OSTI2020

A High-Efficient Solution for Electro-Hydraulic Actuators with Energy Regeneration Capability

This paper proposes a cost-effective, robustly practical solution for a high-efficient electro-hydraulic actuator (EHA) for linear drives. The solution addresses the challenges of high costs and limited efficiency that limit the application of EHA for the electrification of many off-road vehicles. Based on a variable-speed electric motor and a low-cost technology for a fixed-displacement pump, the proposed solution is suitable for a compact implementation and it is capable of energy regeneration under overrunning load conditions. Two different architectures—an open circuit and a closed circuit one—are considered to determine the most practical and efficient configuration as well as the control features. Both architectures minimize throttling losses associated with the conventional regulation of hydraulic actuators. Actuator velocities below the minimum and beyond the maximum allowable pump flow rate are achieved in both architectures using a proportional valve that bypasses the pump flow. The paper describes the design methodology as well as the simulation and experimental activities performed to verify the control strategies as well as energy efficiency. Considering an EHA system of about 20 kW, a complete efficiency map of the system is determined for all the possible four quadrants of operation thus including both resistive and overrunning loads, where energy recuperation is implemented. Simulation and experimental results show that the energy efficiency of the hydraulic systems can reach 84.7% in resistive phases. In assistive phases, the hydraulic system can recover up to 81.8% of the actuator energy. Here, the comparison between open-circuit and closed-circuit structures shows the advantages of the former in terms of energy efficiency. The proposed solution is suitable for electrified hydraulic actuation systems, in both industrial and mobile applications. With the advantages of the low cost of the hydraulic unit and high energy efficiency, it is particularly suitable for mobile applications such as construction machines, that are recently experiencing a significant electrification trend.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1954

Investigation of Transient Combustion Characteristics in a Single Tubular Combustor

An investigation was conducted to determine the combustion response to rapid fuel-flow changes in a single tubular combustor at two simulated altitude-rotor speed conditions of 25,000 feet-70 percent rated engine speed and 50,000 feet-70 percent rated engine speed. Limiting rates of change of fuel flow (acceleration limits) were determined and the effects of certain combustion air flow variables on the transient combustion characteristics were studied with the aid of rapid-response instrumentation.

Donlon, Richard H↗
NASA NTRS2010

Lidar Wind Profiler Comparison to Weather Balloon for Support of Orion Crew Exploration Vehicle Landings

A comparison study by the National Aeronautics and Space Administration Dryden Flight Research Center, Edwards, CA and the Naval Post Graduate School Center for Interdisciplinary Remotely-Piloted Aircraft Studies, Marina, CA was conducted to show the advantages of an airborne wind profiling lidar system in reducing drift uncertainty along a reentry vehicle descent trajectory. This effort was in support of the once planned Orion Crew Exploration Vehicle ground landing. A Twin Otter Doppler Wind Lidar was flown on multiple flights along the approximate ground track of an ascending weather balloons launched from the Marina Municipal Airport. The airborne lidar used was a 5-milli-Joules, 2-micron infrared laser with a 10-centimeter telescope and a two-axis scanner. Each lidar wind profile contains data for an altitude range between the surface and flight altitude of 2,700 meters, processed on board every 20 seconds. In comparison, a typical weather balloon would traverse that same altitude range with a similar data set available in approximately 15-20 minutes. These tests were conducted on November 15 & 16, 2007. Results comparing the balloon and a 10 minute multiple lidar profile averages show a best case absolute difference of 0.18 m/s (0.35 knots) in speed and 1 degree in direction during light and variable (less than 5 knots, without constant direction) wind conditions. These limited test results indicated a standard deviation wind velocity and direction differences of 0.71 m/s (1.3 knots) and 7.17 degrees for 1800Z, and 0.70 m/s (1.3 knots) and 6.79 degrees, outside of cloud layer.

Houtas, Franzeska↗
NASA NTRS1979

Application of digital controls on the quiet clean short haul experimental engines

The digital control systems for the Under-the-Wing (UTW) and Over-the-Wing (OTW) engines developed on the NASA/General Electric Quiet Clean Shorthaul Experimental Engine (QCSEE) program are described. The system to control engine variables includes three major functional parts: system sensors, digital control and system actuators. One of the primary control system functions is to prevent the engine from exceeding speed or temperature limits. The UTW control system also provides fault detection and condition monitoring. The control system requirements for the OTW engine are essentially the same as the UTW engine, however the inlet Mach number control requirement is eliminated, and failure indication and corrective action and full authority digital control are added. The digital controls scheduled the engine variables and maintained engine operation within all physical limits throughout the test program of approximately 200 hours of operation and provided stable and accurate control of both engines.

Saunders, A. A., Jr.↗
NASA NTRS1995

Calculation of design load for the MOD-5A 7.3 mW wind turbine system

Design loads are presented for the General Electric MOD-SA wind turbine. The MOD-SA system consists of a 400 ft. diameter, upwind, two-bladed, teetered rotor connected to a 7.3 mW variable-speed generator. Fatigue loads are specified in the form of histograms for the 30 year life of the machine, while limit (or maximum) loads have been derived from transient dynamic analysis at critical operating conditions. Loads prediction was accomplished using state of the art aeroelastic analyses developed at General Electric. Features of the primary predictive tool - the Transient Rotor Analysis Code (TRAC) are described in the paper. Key to the load predictions are the following wind models: (1) yearly mean wind distribution; (2) mean wind variations during operation; (3) number of start/shutdown cycles; (4) spatially large gusts; and (5) spatially small gusts (local turbulence). The methods used to develop statistical distributions from load calculations represent an extension of procedures used in past wind programs and are believed to be a significant contribution to Wind Turbine Generator analysis. Test/theory correlations are presented to demonstrate code load predictive capability and to support the wind models used in the analysis. In addition MOD-5A loads are compared with those of existing machines. The MOD-5A design was performed by the General Electric Company, Advanced Energy Program Department, under Contract DEN3-153 with NASA Lewis Research Center and sponsored by the Department of Energy.

Mirandy, L.↗
NASA NTRS1970

Laser observations of wave growth and foam density for fetch limited 25 M/SEC winds

The variability of sea surface conditions has been observed from a low flying aircraft by a laser wave profiling system for fetch limited wind speeds of 25 M/SEC. in the North Sea. Wave profiles obtained with the laser system have been analyzed and show that wave growth occurs simultaneously at all frequencies and that an equilibrium value for the higher frequency components is eventually reached, but not before substantially higher (overshoot) values are obtained. Simultaneous photography of the surface has been analyzed and show that 32 percent of the surface is covered with white caps, foam and streaks. This result is in good agreement with a semi-empirical relationship incorporating both the wind speed and the local wave spectrum which predicts 26 percent white water for the conditions observed.

Ross, D. B.↗
NASA NTRS1990

Helicopter far-field acoustic levels as a function of reduced main-rotor advancing blade-tip Mach number

During the design of a helicopter, the weight, engine, rotor speed, and rotor geometry are given significant attention when considering the specific operations for which the helicopter will be used. However, the noise radiated from the helicopter and its relationship to the design variables is currently not well modeled with only a limited set of full-scale field test data to study. In general, limited field data have shown that reduced main-rotor advancing blade-tip Mach numbers result in reduced far-field noise levels. The status of a recent helicopter noise research project is reviewed. It is designed to provide flight experimental data which may be used to further understand helicopter main-rotor advancing blade-tip Mach number effects on far-field acoustic levels. Preliminary results are presented relative to tests conducted with a Sikorsky S-76A helicopter operating with both the rotor speed and the flight speed as the control variable. The rotor speed was operated within the range of 107 to 90 percent NR at nominal forward speeds of 35, 100, and 155 knots.

Mueller, Arnold W.↗
NASA NTRS2017

Aeolus -A Mission to Study the Thermal and Wind Environment of Mars

Aeolus is a small satellite mission to observe surface and atmospheric forcing and general circulation of Mars, by measuring surface energy balance, atmospheric temperatures, aerosols and clouds, and winds. Critically, Aeolus will make these measurements at all local times of day, providing information on both seasonal and diurnal variability. To date, direct measurements of Martian wind speeds have only been possible at the surface, only during daylight hours, and over small areas limited by rover traverse capabilities. From orbit, thermal measurements (e.g., estimates from assumed geostrophic balance) as well as images of dust storms and dune migration have provided inputs to derive current data sets on Martian winds. However, Mars General Circulation models demonstrate that wind speeds derived from these indirect measurements may be in error by 50 to 100%. For this reason, direct wind velocity measurements have been deemed "High Priority" by MEPAG (Mars Exploration Program Analysis Group); measuring wind speeds and corresponding thermal data is vital to understanding the climate of Mars. Aeolus will carry four Spatial Heterodyne Spectrometers (SHS), coupled to two orthogonal viewing telescopes. These high-resolution near-infrared spectrometers will measure CO2 (daytime absorption) and O2 (day and night emission) lines in the Martian atmosphere. Doppler shifts in these lines can be measured during Martian day and night, resolving wind speeds down to ~5 m/s. Orthogonal views allow the spectrometers to capture wind vectors over all observation locations. Aeolus will also carry the atmospheric limb-viewing Thermal Limb Sounder (TLS) to measure atmospheric temperatures, water ice clouds, and dust abundances across all altitudes where winds are measured. Finally, the Surface Radiometric Sensor Package (SuRSeP), a nadir viewing radiometer, will measure the total reflected solar and emitted thermal radiance, surface temperature, and water cloud and dust total column abundances. The combined spectral and thermal measurements will provide a new understanding of the global energy balance, dust transport processes, and climate cycles in the Martian atmosphere. Aeolus will consist of a single satellite in a near-polar orbit, allowing it to pass over all local times, with the baseline mission observing all seasons of an entire Martian year (two Earth years). Aeolus was one of two Martian smallsat concepts selected for study through the Planetary Science Deep Space SmallSat Studies program. This talk will provide an overview of the mission, including science rationale, instruments, spacecraft, and mission operations concept.

and winds↗
DOE OSTI2024

Limits on the evolutionary rates of biological traits

Abstract This paper focuses on the maximum speed at which biological evolution can occur. I derive inequalities that limit the rate of evolutionary processes driven by natural selection, mutations, or genetic drift. These rate limits link the variability in a population to evolutionary rates. In particular, high variances in the fitness of a population and of a quantitative trait allow for fast changes in the trait’s average. In contrast, low variability makes a trait less susceptible to random changes due to genetic drift. The results in this article generalize Fisher’s fundamental theorem of natural selection to dynamics that allow for mutations and genetic drift, via trade-off relations that constrain the evolutionary rates of arbitrary traits. The rate limits can be used to probe questions in various evolutionary biology and ecology settings. They apply, for instance, to trait dynamics within or across species or to the evolution of bacteria strains. They apply to any quantitative trait, e.g., from species’ weights to the lengths of DNA strands.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Limits on the Evolutionary Rates of Biological Traits

This paper focuses on the maximum speed at which biological evolution can occur. I derive inequalities that limit the rate of evolutionary processes driven by natural selection, mutations, or genetic drift. These rate limits link the variability in a population to evolutionary rates. In particular, high variances in the fitness of a population and of a quantitative trait allow for fast changes in the trait’s average. In contrast, low variability makes a trait less susceptible to random changes due to genetic drift. The results in this article generalize Fisher’s fundamental theorem of natural selection to dynamics that allow for mutations and genetic drift, via trade-of relations that constrain the evolutionary rates of arbitrary traits. The rate limits can be used to probe questions in various evolutionary biology and ecology settings. They apply, for instance, to trait dynamics within or across species or to the evolution of bacteria strains. They apply to any quantitative trait, e.g., from species’ weights to the lengths of DNA strands.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Vertical-Axis Wind Turbine Steady and Unsteady Aerodynamics for Curved Deforming Blades

Vertical-axis wind turbines’ simpler design and low center of gravity make them ideal for floating wind applications. However, efficient design optimization of floating systems requires fast and accurate models. Low-fidelity vertical-axis turbine aerodynamic models, including double multiple streamtube and actuator cylinder theory, were created during the 1980s. Commercial development of vertical-axis turbines all but ceased in the 1990s until around 2010 when interest resurged for floating applications. Despite the age of these models, the original assumptions (2-D, rigid, steady, straight bladed) have not been revisited in full. When the current low-fidelity formulations are applied to modern turbines in the unsteady domain, aerodynamic load errors nearing 50% are found, consistent with prior literature. However, a set of steady and unsteady modifications that remove the majority of error is identified, limiting it near 5%. This paper shows how to reformulate the steady models to allow for unsteady inputs including turbulence, deforming blades, and variable rotational speed. A new unsteady approximation that increases numerical speed by 5–10× is also presented. Combined, these modifications enable full-turbine unsteady simulations with accuracy comparable to higher-fidelity vortex methods, but over 5000× faster.

17 WIND ENERGY↗
NASA NTRS1971

Parameter identification using a creeping-random-search algorithm

A creeping-random-search algorithm is applied to different types of problems in the field of parameter identification. The studies are intended to demonstrate that a random-search algorithm can be applied successfully to these various problems, which often cannot be handled by conventional deterministic methods, and, also, to introduce methods that speed convergence to an extremal of the problem under investigation. Six two-parameter identification problems with analytic solutions are solved, and two application problems are discussed in some detail. Results of the study show that a modified version of the basic creeping-random-search algorithm chosen does speed convergence in comparison with the unmodified version. The results also show that the algorithm can successfully solve problems that contain limits on state or control variables, inequality constraints (both independent and dependent, and linear and nonlinear), or stochastic models.

Parrish, R. V.↗