Search NASA⌕ Search

SEARCH · Search NASA

Results for “vehicle matching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Comparison of Anthropomorphic Test Device and Human Volunteer Responses in Simulated Landing Impact Tests of U.S. Space Vehicles

United States (U.S.) crewed vehicles are being designed to support the National Aeronautics and Space Administration’s (NASA’s) human spaceflight programs. Vehicles must be designed to meet NASA’s occupant protection requirements including landing injury assessment with anthropomorphic test devices (ATDs) and analytical models. However, these tools are limited in capturing all injuries that might occur during spacecraft landings. A NASA study of injuries during Soyuz vehicle landings has shown that analytical models are underpredicting occupant injury. Because of the inherent limitations with our analytical tools, human volunteer impact testing was employed to assess flight-like landing conditions of U.S. crewed vehicles. A total of 84 human volunteer tests in 11 different test orientations and g-levels were completed as part of this effort in collaboration with the Air Force Research Laboratory (AFRL) at Wright-Patterson Air Force Base and U.S. vehicle development companies. Human subjects were tested at various realistic landing loads and in the highest fidelity seat and suit components that were available at the time of testing for two U.S. vehicles. Matched-pair ATD tests in the same test conditions were also conducted with small female and midsized male Hybrid III ATDs. ATDs were fully instrumented. Head accelerations and subjective responses were recorded for human subjects. In some cases, chest accelerations were captured. Responses of the ATDs and humans in matched-pair tests were compared. No ATD tests showed evidence for risk of injury based on NASA occupant protection requirements. Human subjects reported 17 cases of discomfort or pain, and 1 human subject was diagnosed with a minor injury that was not evident in the ATD tests. These results provide evidence that ATDs do not capture all potential injury risks, namely lower severity injuries, discomfort, pain, and fit issues. Overall, human testing is beneficial to understanding the true risk of injury to crewmembers during Earth landings.

Teresa M Reiber↗
NASA NTRSDate not supplied

Comparison of Anthropomorphic Test Device and Human Volunteer Responses in Simulated Landing Impact Tests of U.S. Space Vehicles

United States (U.S.) crewed vehicles are being designed to support the National Aeronautics and Space Administration’s (NASA’s) human spaceflight programs. Vehicles must be designed to meet NASA’s occupant protection requirements including landing injury assessment with anthropomorphic test devices (ATDs) and analytical models. However, these tools are limited in capturing all injuries that might occur during spacecraft landings. A NASA study of injuries during Soyuz vehicle landings has shown that analytical models are underpredicting occupant injury. Because of the inherent limitations with our analytical tools, human volunteer impact testing was employed to assess flight-like landing conditions of U.S. crewed vehicles. A total of 84 human volunteer tests in 11 different test orientations and g-levels were completed as part of this effort in collaboration with the Air Force Research Laboratory (AFRL) at Wright-Patterson Air Force Base and U.S. vehicle development companies. Human subjects were tested at various realistic landing loads and in the highest fidelity seat and suit components that were available at the time of testing for two U.S. vehicles. Matched-pair ATD tests in the same test conditions were also conducted with small female and midsized male Hybrid III ATDs. ATDs were fully instrumented. Head accelerations and subjective responses were recorded for human subjects. In some cases, chest accelerations were captured. Responses of the ATDs and humans in matched-pair tests were compared. No ATD tests showed evidence for risk of injury based on NASA occupant protection requirements. Human subjects reported 17 cases of discomfort or pain, and 1 human subject was diagnosed with a minor injury that was not evident in the ATD tests. These results provide evidence that ATDs do not capture all potential injury risks, namely lower severity injuries, discomfort, pain, and fit issues. Overall, human testing is beneficial to understanding the true risk of injury to crewmembers during Earth landings.

Teresa M Reiber↗
NASA NTRS1991

Analysis of terrain map matching using multisensing techniques for applications to autonomous vehicle navigation

This paper describes skyline-based terrain matching, a new method for locating the vantage point of laser range-finding measurements on a global map previously prepared by satellite or aerial mapping. Skylines can be extracted from the range-finding measurements and modelled from the global map, and are represented in parametric, cylindrical form with azimuth angle as the independent variable. The three translational parameters of the vantage point are determined with a three-dimensional matching of these two sets of skylines.

Page, Lance↗
NASA NTRS2006

Boom Rendezvous Alternative Docking Approach

Space rendezvous and docking has always been attempted with primarily one philosophic methodology. The slow matching of one vehicle's orbit by a second vehicle and then a final closing sequence that ends in matching the orbits with perfect precision and with near zero relative velocities. The task is time consuming, propellant intensive, risk inherent (plume impingement, collisions, fuel depletion, etc.) and requires substantial hardware mass. The historical background and rationale as to why this approach is used is discussed in terms of the path-not-taken and in light of an alternate methodology. Rendezvous and docking by boom extension is suggested to have inherent advantages that today s technology can readily exploit. Extension from the primary spacecraft, beyond its inherent large inertia, allows low inertia connections to be made rapidly and safely. Plume contamination issues are eliminated as well as the extra propellant mass and risk required for the final thruster (docking) operations. Space vehicle connection hardware can be significantly lightened. Also, docking sensors and controls require less fidelity; allowing them to be more robust and less sensitive. It is the potential safety advantage and mission risk reduction that makes this approach attractive, besides the prospect of nominal time and mass savings.

Bonometti, Joseph A.↗
DOE OSTI2024

Optimization of Dynamic Ride-Sharing by Considering User Preference Through Discount and Delay Tolerance

Dynamic ride-sharing (DRS) has been projected to be a key solution to lowering system-wide congestion. Despite recent development progress, demand studies for DRS suggest low levels of willingness for travelers to use such services. The disconnect between DRS system designs and user preferences limits the application impacts of DRS in the real world. Therefore, this paper aims to design a new DRS system by considering the user preferences of choices under different levels of services. In this study, an agent-based approach is used to model a fleet of shared vehicles that allows DRS. An optimization model is developed to match riders to vehicles while accounting for traveler delay and delay acceptance. Travelers are also dynamically issued predictive discounts to incentivize them to accept longer trip delays. Results show that the proposed approach can improve system efficiency by increasing average vehicle occupancy by up to 1.0 persons/trip and DRS acceptance up to 38.9% depending on fleet size. Additionally, congestion is eased through the decrease of empty vehicle miles traveled by up to 7.1%.

Paul, Joseph↗
DOE OSTI2024

Integrating Human Factors in Dynamic Rideshare Assignment: Willingness-To-Pay for Delay

Dynamic ride-sharing (DRS) has been projected to be a key solution to lowering system-wide congestion. Despite recent developmental progress, demand studies for DRS suggest low levels of willingness for travelers to use such services. The disconnect between DRS system designs and user preferences limits the application impacts of DRS in the real world. Therefore, this paper aims to design a new DRS trip/vehicle assignment strategy by considering the user preferences of choices under different levels of service. In this study, an agent-based simulation approach is used to model a fleet of shared vehicles that allows DRS. An optimization model is developed to match riders to vehicles while accounting for traveler delay and delay acceptance. Travelers are also dynamically issued predictive discounts, catered to their expected willingness to pay, to incentivize them to accept longer trip delays. Results show that the proposed approach can improve system efficiency by increasing average vehicle occupancy by up to 1.0 persons/trip and DRS acceptance by up to 38.9% depending on fleet size. Additionally, congestion is eased through the decrease of empty vehicle miles traveled by up to 7.1%.

Paul, Joseph↗
NASA NTRS1978

A cycle timer for testing electric vehicles

A cycle timer was developed to assist the driver of an electric vehicle in more accurately following and repeating SAE driving schedules. These schedules require operating an electric vehicle in a selected stop-and-go driving cycle and repeating this cycle pattern until the vehicle ceases to meet the requirements of the cycle. The heart of the system is a programmable read-only memory (PROM) that has the required test profiles permanently recorded on plug-in cards, one card for each different driving schedule. The PROM generates a direct current analog signal that drives a speedometer displayed on one scale of a dual movement meter. The second scale of the dual movement meter displays the actual speed of the vehicle as recorded by the fifth wheel. The vehicle operator controls vehicle speed to match the desired profile speed. The PROM controls the recycle start time as well as the buzzer activation. The cycle programmer is powered by the test vehicle's 12-volt accessory battery, through a 5-volt regulator and a 12-volt dc-to-dc converter.

Soltis, R. F.↗
DOE OSTI2021

Influence of Fuel Properties on Gasoline Direct Injection Particulate Matter Emissions Over First 200 s of World-Harmonized Light-Duty Test Procedure Using an Engine Dynamometer and Novel “Virtual Drivetrain” Software

Abstract The influence of fuel properties on particulate matter (PM) emissions from a catalytic gasoline particulate filter (GPF) equipped gasoline direct injection (GDI) engine was investigated using novel “virtual drivetrain” software and an engine mated to an engine dynamometer. The virtual drivetrain software was developed in labview to operate the engine on an engine dynamometer as if it were in a vehicle undergoing a driving cycle. The software uses a physics-based approach to determine vehicle acceleration and speed based on engine load and a programed “shift” schedule to control engine speed. The software uses a control algorithm to modulate engine load and braking to match a calculated vehicle speed with the prescribed speed trace of the driving cycle of choice. The first 200 s of the World-harmonized Light-duty Test Procedure (WLTP) driving cycle was tested using six different fuel formulations of varying volatility, aromaticity, and ethanol concentration. The first 200 s of the WLTP was chosen as the test condition because it is the most problematic section of the driving cycle for controlling PM emissions due to the cold start and cold drive off. It was found that there was a strong correlation between aromaticity of the fuel and the engine-out PM emissions, with the highest emitting fuel producing more than double the mass emissions of the low PM production fuel. However, the post-GPF PM emissions depended greatly on the soot loading state of the GPF. The fuel with the highest engine-out PM emissions produced comparable post-GPF emissions to the lowest PM producing fuel over the driving cycle when the GPF was loaded over three cycles with the respective fuels. These results demonstrate the importance of GPF loading state when aftertreatment systems are used for PM reduction. It also shows that GPF control may be more important than fuel properties, and that regulatory compliance for PM can be achieved with proper GPF control calibration irrespective of fuel type.

Energy & Fuels↗
NASA NTRS1996

Pulse Detonation Engine Air Induction System Analysis

A preliminary mixed-compression inlet design concept for potential pulse-detonation engine (PDE) powered supersonic aircraft was defined and analyzed. The objectives of this research were to conceptually design and integrate an inlet/PDE propulsion system into a supersonic aircraft, perform time-dependent CFD analysis of the inlet flowfield, and to estimate the installed PDE cycle performance. The study was baselined to a NASA Mach 5 Waverider study vehicle in which the baseline over/under turboramjet engines were replaced with a single flowpath PDE propulsion system. As much commonality as possible was maintained with the baseline configuration, including the engine location and forebody lines. Modifications were made to the inlet system's external ramp angles and a rotating cowl lip was incorporated to improve off-design inlet operability and performance. Engines were sized to match the baseline vehicle study's ascent trajectory thrust requirement at Mach 1.2. The majority of this study was focused on a flight Mach number of 3.0. The time-dependent Navier Stokes CFD analyses of a two-dimensional approximation of the inlet was conducted for the Mach 3.0 condition. The Lockheed Martin Tactical Aircraft Systems-developed FALCON CFD code with a two equation 'k-1' turbulence model was used. The downstream PDE was simulated by an array of four sonic nozzles in which the flow areas were rapidly varied in various opening/closing combinations. Results of the CFD study indicated that the inlet design concept operated successfully at the Mach 3.0 condition, satisfying mass capture, total pressure recovery, and operability requirements. Time-dependent analysis indicated that pressure and expansion waves from the simulated valve perturbations did not effect the inlet's operability or performance.

Pegg, R. J.↗
NASA NTRS2014

An Experimental Study of Launch Vehicle Propellant Tank Fragmentation

In order to better understand launch vehicle abort environments, Bangham Engineering Inc. (BEi) built a test assembly that fails sample materials (steel and aluminum plates of various alloys and thicknesses) under quasi-realistic vehicle failure conditions. Samples are exposed to pressures similar to those expected in vehicle failure scenarios and filmed at high speed to increase understanding of complex fracture mechanics. After failure, the fragments of each test sample are collected, catalogued and reconstructed for further study. Post-test analysis shows that aluminum samples consistently produce fewer fragments than steel samples of similar thickness and at similar failure pressures. Video analysis shows that there are several failure 'patterns' that can be observed for all test samples based on configuration. Fragment velocities are also measured from high speed video data. Sample thickness and material are analyzed for trends in failure pressure. Testing is also done with cryogenic and noncryogenic liquid loading on the samples. It is determined that liquid loading and cryogenic temperatures can decrease material fragmentation for sub-flight thicknesses. A method is developed for capture and collection of fragments that is greater than 97 percent effective in recovering sample mass, addressing the generation of tiny fragments. Currently, samples tested do not match actual launch vehicle propellant tank material thicknesses because of size constraints on test assembly, but test findings are used to inform the design and build of another, larger test assembly with the purpose of testing actual vehicle flight materials that include structural components such as iso-grid and friction stir welds.

Richardson, Erin↗
NASA NTRS1985

Holding Cargo in Place With Foam

Foam fills entire container to protect cargo from shock and vibration. Originally developed for stowing space debris and spent satellites in Space Shuttle for return to Earth, encapsulation concept suitable for preparing shipments carried by truck, boat, or airplane. Equipment automatically injects polyurethane foam into its interior to hold cargo securely in place. Container of rectangular or other cross section built to match shape of vehicle used.

Fisher, T. T.↗
NASA NTRS1991

Conceptual design of an orbital debris collector

The current Lower Earth Orbit (LEO) environment has become overly crowded with space debris. An evaluation of types of debris is presented in order to determine which debris poses the greatest threat to operation in space, and would therefore provide a feasible target for removal. A target meeting these functional requirements was found in the Cosmos C-1B Rocket Body. These launchers are spent space transporters which constitute a very grave risk of collision and fragmentation in LEO. The motion and physical characteristics of these rocket bodies have determined the most feasible method of removal. The proposed Orbital Debris Collector (ODC) device is designed to attach to the Orbital Maneuvering Vehicle (OMV), which provides all propulsion, tracking, and power systems. The OMV/ODC combination, the Rocket Body Retrieval Vehicle (RBRV), will match orbits with the rocket body, use a spin table to match the rotational motion of the debris, capture it, despin it, and remove it from orbit by allowing it to fall into the Earth's atmosphere. A disposal analysis is presented to show how the debris will be deorbited into the Earth's atmosphere. The conceptual means of operation of a sample mission is described.

Odonoghue, Peter↗
NASA NTRS1978

Weight propagation and equivalent horsepower for alternate-engined cars

In order to evaluate properly the consequences of replacing conventional Otto-cycle engines with alternate power systems, comparisons must be carried out at the vehicle level with functionally equivalent cars. This paper presents the development and application of a procedure for establishing equivalent vehicles. A systematic weight propagation methodology, based on detailed weight breakdowns and influence factors, yields the vehicle weight impacts due to changes in engine weight and power. Performance-matching criteria, utilizing a vehicle simulation program, are then employed to establish Otto-engine-equivalent vehicles, whose characteristics can form the basis for alternative engine evaluations.

Klose, G. J.↗
NASA NTRS1991

Matching Terrain-Height Maps For A Robotic Vehicle

Computational method for merging coarser- and finer-scale terrain-height data developed. Terrain-height data from aerial photographs merged with similar data on finer scale estimated from stereoscopic-vision and wheel-sensor outputs on robotic vehicle. Intended for use in guiding motions of proposed Mars rover vehicle, underlying concept applicable to such other problems as guiding semiautonomous robotic land vehicles in general and merging different topographical maps containing partly conflicting and/or partly unreliable data on same terrain.

Gennery, Donald B.↗
NASA NTRS1987

Guidance and control strategies for aerospace vehicles

A simplified method of matched asymptotic expansions was developed where the common part in composite solution is generated as a polynomial in stretched variable instead of actually evaluating the same from the outer solution. This methodology was applied to the solution of the exact equations for three dimensional atmospheric entry problems. Compared to previous works, the present simplified methodology yields explicit analytical expressions for various components of the composite solution without resorting to any type of transcendental equations to be solved only by numerical methods. The optimal control problem arising in the noncoplanar orbital transfer employing aeroassist was also addressed.

Hibey, Joseph L.↗
DOE OSTI2023

Model Based Validation of Intelligent Powertrain Strategies for Connected and Automated Vehicles

Systems incorporating Vehicle to Everything (V2X) and conventional cellular based communication in vehicles can significantly help improve energy consumption via a combination of intelligent powertrain control strategies, smarter routing algorithms and driving in such a way as to minimize fuel economy and the emission of carbon dioxide, known as "eco-driving." In projects led by the Southwest Research Institute (SwRI), large-scale traffic simulations are created to model real-world scenarios with dynamic behavior that is reactive to imposed changes. Coupled with high fidelity powertrain models, the closed loop framework enables research and development of such Connected and Automated Vehicle (CAV) enabled technologies at scale. This paper will discuss a traffic system simulation environment that was built based on the High Street urban corridor in Columbus, Ohio. Eco-driving strategies were tested at scale on a variety of powertrain platforms – internal combustion engines, hybrid electric and fully electric vehicles. Furthermore, the paper will focus on hybrid electric powertrain modeling along with details on how the powertrain model was leveraged to develop a sophisticated clustering scheme to help down-select speed traces from large scale simulation studies for validation on vehicle dynamometer. Nominal energy consumption improvement around 12% was observed with good match between simulation studies and vehicle testing.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1961

Trajectory Control in Rendezvous Problems Using Proportional Navigation

The rendezvous problem is defined by the end conditions that the position and velocity of a vehicle and its target are to be matched. In its present form proportional navigation theory allows the interception of a target by the vehicle, that is , the matching of positions. This report extends the theory to include the full rendezvous end conditions. Trajectory constraint equations are derived and the method of computing the required thrust program in idealized problems is outlined. The thrust program obtained results entirely from the trajectory and does not consider the dynamics of the vehicles or errors inherent in a real system. The properties of the thrust program, such as its variation both in magnitude and direction, are examined. An acceleration forcing function is also derived and its properties examined. The theory is applied to the satellite rendezvous problem as an example and some computations are presented.

Cicolani, Luigi S.↗
DOE OSTI2025

Vehicular Re-Identification from Uncontrolled Multiple Views

Vehicle re-identification (re-ID) across disparate sensing modalities remains a fundamental challenge for transportation research. In this work, we introduce a deep multi-view vehicle re-ID framework that leverages Siamese networks to compare pairs of vehicle images and produce matching scores, enabling robust association across drastically different viewpoints such as those from UAVs, surveillance cameras, and ground sensors. The model exploits convolutional neural networks to learn features that remain discriminative under changes in angle, distance, and illumination, supporting more generalizable re-ID performance. As part of this effort, we also developed an automated pipeline to synchronize roadside and UAV video streams, producing a multi-perspective dataset that complements preexisting real collections and a synthetic dataset generated in this study. Together, these contributions advance the capability to re-identify vehicles across wide viewing baselines; establish a foundation for scalable, reproducible research in vehicle re-ID; and open pathways for future applications, such as inferring routine behaviors, movement patterns, and daily habits of the individual associated with the vehicle.

convolutional neural networks↗