Search NASA⌕ Search

SEARCH · Search NASA

Results for “wake identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

An application of parameter identification to the oscillatory motion of an airplane at high C(L)

This paper presents an application of a stepwise regression incorporating polynomial splines to oscillatory flight data from a light research airplane operating at near stall angles of attack. It is shown that data from several experiments can be combined into a large data set for analysis and that hysteresis phenomena can be observed in this large data set. Finally, it is postulated from the analysis of the flight data and theoretical calculations that the observed oscillatory motion is the result of a combination of wing stall and wing wake position at the tail.

Batterson, J. G.↗
NASA NTRSDate not supplied

Static and Forced Oscillation Wind Tunnel Tests of A Tandem Propeller Configuration

A series of static and forced oscillation tests were conducted using a tandem propeller configuration in the NASA Langley 12-Foot Low-Speed Tunnel. The primary objectives were to quantify the effect of aerodynamic interactions on propeller thrust and identify conditions where the effect is most significant. A secondary objective was to obtain a preliminary data set from dynamic testing to assess the impact of angular rate on thrust performance. This paper presents analysis of the experimental data, which includes propeller performance measurements and qualitative flow visualization. The static results show that the rear propeller in the tandem configuration can experience thrust degradations greater than 30%. The extent of the wake interaction is a function of the hub separation distance and the advance ratio of the front propeller. Forced oscillation results showed that the front propeller exhibited primarily linear behavior across the conditions tested, whereas the rear propeller exhibited dynamic nonlinearity in the region of significant thrust degradation. These results are intended to support high-fidelity modeling research, particularly for flight dynamics simulation development to aid trajectory prediction, control design, and identification of hazardous conditions for multirotor vehicles.

Aerodynamic Interactions↗
NASA NTRS2010

Optimization of a Multi-Stage ATR System for Small Target Identification

An Automated Target Recognition system (ATR) was developed to locate and target small object in images and videos. The data is preprocessed and sent to a grayscale optical correlator (GOC) filter to identify possible regionsof- interest (ROIs). Next, features are extracted from ROIs based on Principal Component Analysis (PCA) and sent to neural network (NN) to be classified. The features are analyzed by the NN classifier indicating if each ROI contains the desired target or not. The ATR system was found useful in identifying small boats in open sea. However, due to "noisy background," such as weather conditions, background buildings, or water wakes, some false targets are mis-classified. Feedforward backpropagation and Radial Basis neural networks are optimized for generalization of representative features to reduce false-alarm rate. The neural networks are compared for their performance in classification accuracy, classifying time, and training time.

false alarm rate↗
NASA NTRS2004

Exploration of Terminal Procedures Enabled by NASA Wake VAS Technologies

The National Aeronautics and Space Administration (NASA) tasked The MITRE Corporation's Center for Advanced Aviation System Development (CAASD) to investigate potential air traffic control (ATC) procedures that could benefit from technology used or developed in NASA's Wake Vortex Advisory System (WakeVAS). The task also required developing an estimate of the potential benefits of the candidate procedures. The main thrust of the investigation was to evaluate opportunities for improved capacity and efficiency in airport arrival and departure operations. Other procedures that would provide safety enhancements were also considered. The purpose of this investigation was to provide input to the WakeVAS program office regarding the most promising areas of development for the program. A two-fold perspective was desired: First, identification of benefits from possible procedures enabled by both incremental components and the mature state of WakeVAS technology; second identification of procedures that could be expected to evolve from the current Federal Aviation Administration (FAA) procedures. The evolution of procedures should provide meaningful increments of benefit and a low risk implementation of the WakeVAS technologies.

Lunsford, Clark R.↗
NASA NTRS1988

Helicopter main-rotor noise: Determination of source contributions using scaled model data

Acoustic data from a test of a 40 percent model MBB BO-105 helicopter main rotor are scaled to equivalent full-scale flyover cases. The test was conducted in the anechoic open test section of the German-Dutch Windtunnel (DNW). The measured data are in the form of acoustic pressure time histories and spectra from two out-of-flow microphones underneath and foward of the model. These are scaled to correspond to measurements made at locations 150 m below the flight path of a full-scale rotor. For the scaled data, a detailed analysis is given for the identification in the data of the noise contributions from different rotor noise sources. Key results include a component breakdown of the noise contributions, in terms of noise criteria calculations of a weighted sound pressure level (dBA) and perceived noise level (PNL), as functions of rotor advance ratio and descent angle. It is shown for the scaled rotor that, during descent, impulsive blade-vortex interaction (BVI) noise is the dominant contributor to the noise. In level flight and mild climb, broadband blade-turbulent wake interaction (BWI) noise is dominant due to the absence of BVI activity. At high climb angles, BWI is reduced and self-noise from blade boundary-layer turbulence becomes the most prominent.

Brooks, Thomas F.↗
NASA NTRS1975

Detection of severe storms by satellites

Ideas are presented for severe storm identification based on satellite data. The tops of huge thunderstorms in satellite pictures often appear as vast areas of extensive cirrus cloud; they consist of clusters of anvil clouds, each generated by vigorous thunderstorm circulation. The overshooting tops observed in satellite pictures are located where the subanvil updrafts are the strongest. Learjet experiment results show that an overshooting top varies either quickly or slowly, depending on the characteristics of individual clouds. When an overshooting top collapses, a small segment of the anvil cirrus jumps upward in the wake of the overshooting top. Also discussed is the monitoring of vertical motions from satellites and tornado-producing thunderstorms from geostationary altitude. A very high-resolution imagery of both infrared and visual spectral bands makes it possible to infer vertical motions beneath the anvil top. A combination of cloud velocity and anvil expansion rate will permit, in the future, determining the location of severe storms within the vast areas of anvil clouds.

Fujita, T. T.↗
NASA NTRS1982

Measurements by the plasma diagnostics package on STS-3

A comprehensive set of measurements about the orbiter environment are provided by the plasma diagnostics package (PDP). Ion and electron particle densities, energies, and spatial distribution functions; ion mass for identification of particular molecular ion species; and magnetic fields, electric fields and electromagnetic waves over a broad frequency range are studied. Shuttle environmental measurements will be made both on the pallet and, by use of the remote manipulator system (RMS), the PDP will be maneuvered in and external to the bay area to continue environmental measurements and to carry on a joint plasma experiment with the Utah State University fast-pulsed electron generator. Results of orbiter environment EMI measurements and S-band field strengths as well as preliminary results from wake search operations indicating wake boundary identifiers are reported.

Shawhan, S. D.↗
NASA NTRS1985

X-ray emission possibly coincident with the radio tail of PKS 0301 - 123

X-ray, radio, and optical observations are reported for a very poor cluster of galaxies containing the radio source PKS 0301 - 123. A long, 100,000 second X-ray observation using the Einstein Observatory's IPC resulted in the serendipitous discovery of a peculiar extended X-ray morphology associated with the poor cluster. The X-ray emission is extended in the same direction and is approximately the same length as the radio-tailed source, PKS 0301 - 123, which was mapped at 6 and 20 cm with the VLA. Optical redshift observations with the KPNO IIDS on the 2.1 m telescope confirm the identification of the X-ray and radio emission with the poor cluster at z = 0.1. It is argued that the X-ray extension is unlikely to be a chance coincidence of a background source projected onto the foreground cluster. Therefore, four possible mechanisms which might physically link the X-ray and radio emission are considered: thermal bremsstrahlung from a cluster with a flattened potential well; inverse Compton scattering of the relativistic electrons in the radio source, X-ray synchrotron radiation; and heating the cluster gas by the turbulent wake of the radio galaxy. The prospects for future observations of such X-ray/radio coincidences are briefly discussed.

Burns, J. O.↗
NASA NTRS2011

Identification of Cardiometabolic Vulnerabilities Caused by Effects of Synergistic Stressors that are Commonly Encountered During Space Missions

Microgravity is a physiologically challenging state even when at rest. Astronauts experience additional physical and mental stresses, such as prolonged exertion, sleep loss and circadian misalignment, that could impact cardiovascular function. The main goals of this four year NASA project are to characterize the independent and synergistic effects on cardiovascular and immune function of: (1) circadian misalignment; (2) sleep loss; and (3) varied physical and mental stressors, mimicking some of the synergistic stressors experienced by astronauts. Sixteen healthy volunteers, aged 35-55 years, will be studied with standardized behavioral stressors occurring across all circadian phases, both with and without accruing sleep loss, achieved via two 11-day "forced desynchrony" protocols performed in each subject (randomized, within-subject design), where wake periods are advanced 4-h each "day" (i.e. recurring 20-h "days"). One protocol permits 8.33 h sleep opportunity per 20-h "day" (=10 h sleep per 24-h), and the other permits 5 h sleep per 20-h "day" (=6 h sleep per 24-h; matching the reported sleep duration of astronauts). In both protocols, subjects will perform a standardized stress battery including a cognitively challenging task; bicycle exercise, and passive 60deg head up tilt. Outcome variables include blood pressure, heart rate, arrhythmia frequency, cardiac vagal tone (from heart rate variability), sympathetic activity (catecholamines), and endothelial function. Additional measures of cardiac function (echocardiography), responses to a passive 80deg head up tilt, maximal oxygen uptake, and immune function will be assessed at the beginning and at the end of each protocol (i.e., without and with sleep loss, and before and after circadian misalignment). We hope to identify the relative impact on cardiovascular risk markers of varied behavioural stressors while subjects experience circadian misalignment and sleep loss, mimicking some of the synergistic stressors experienced by astronauts. Supported by NASANNX1 OAR 1 OG.

Ruger, M.↗
NASA NTRS2022

Identification and Reduction of Interactional Noise of a Quadcopter in Hover and Forward Flight Conditions

Advanced Air Mobility is a vision for a safe, accessible, and sustainable aviation system to transport people and cargo between places not served by traditional aviation. With this emerging transportation industry, there is motivation to characterize the noise of vehicles to determine their potential impacts on the community. An experimental testing campaign was conducted on a representative model of a small unmanned aircraft system in the NASA Langley Low Speed Aeroacoustic Wind Tunnel as a continuation of a previous testing campaign. The goals of the current test are to identify sources of interactional noise as well as to test custom-designed rotors and noise reduction devices. The tested noise reduction methods involve increasing the vertical distances between the rotors and the vehicle airframe as well as between the forward and aft rotor disk planes. These methods are intended to reduce rotor-airframe interaction noise in hover and fore-aft rotor wake ingestion noise in forward flight. A phased microphone array is also utilized to identify the locations of prominent noise generation for the different vehicle configurations in forward flight. Elevation of the rotors from the vehicle airframe yielded nearly 8 dBA overall noise reduction in forward flight, while yielding up to 4 dB reduction in overall tonal levels for one of the rotors in hover.

Nikolas S Zawodny↗
NASA NTRS2000

Ground Vibration Test Planning and Pre-Test Analysis for the X-33 Vehicle

This paper describes the results of the modal test planning and the pre-test analysis for the X-33 vehicle. The pre-test analysis included the selection of the target modes, selection of the sensor and shaker locations and the development of an accurate Test Analysis Model (TAM). For target mode selection, four techniques were considered, one based on the Modal Cost technique, one based on Balanced Singular Value technique, a technique known as the Root Sum Squared (RSS) method, and a Modal Kinetic Energy (MKE) approach. For selecting sensor locations, four techniques were also considered; one based on the Weighted Average Kinetic Energy (WAKE), one based on Guyan Reduction (GR), one emphasizing engineering judgment, and one based on an optimum sensor selection technique using Genetic Algorithm (GA) search technique combined with a criteria based on Hankel Singular Values (HSV's). For selecting shaker locations, four techniques were also considered; one based on the Weighted Average Driving Point Residue (WADPR), one based on engineering judgment and accessibility considerations, a frequency response method, and an optimum shaker location selection based on a GA search technique combined with a criteria based on HSV's. To evaluate the effectiveness of the proposed sensor and shaker locations for exciting the target modes, extensive numerical simulations were performed. Multivariate Mode Indicator Function (MMIF) was used to evaluate the effectiveness of each sensor & shaker set with respect to modal parameter identification. Several TAM reduction techniques were considered including, Guyan, IRS, Modal, and Hybrid. Based on a pre-test cross-orthogonality checks using various reduction techniques, a Hybrid TAM reduction technique was selected and was used for all three vehicle fuel level configurations.

Bedrossian, Herand↗
NASA NTRS2018

Identification of Safety Metrics for Airport Surface Operations

A large fraction of safety incidents occurs on the ground during airport surface operations. Although these incidents are mostly non-fatal with a few exceptions, they are high profile incidents that remain a source of concern for the National Transportation Safety Board (NTSB), the Federal Aviation Administration (FAA), major airlines, and other stakeholders of the National Airspace System (NAS). These incidents have historically been mitigated by implementing changes to regulations, policies, and procedures over time. This approach has minimized but not eliminated the risk of occurrence of safety incidents. It is thus important to develop integrated techniques to assess, model, and prevent these incidents by analyzing the risk and likelihood of occurrence and communicating results of the analysis to decision-making personnel who can mitigate and prevent incidents in real time. The work presented in this paper builds on a previously developed architecture for safety, Real-Time Safety Monitoring (RTSM), to enable monitoring and prediction of the safety of the NAS. In the RTSM framework, hazards to flight are translated to safety metrics such as wake vortex encounters or loss of separation, that can be modeled and analyzed offline and also predicted and monitored in real time (online). The intent of this paper is to integrate predictable incidents that occur during surface and ground operations into the safety portfolio of the RTSM project by (i) identifying suitable information sources from which ground incidents can be studied, (ii) developing safety metrics correlated with surface operations, and (iii) recommending suitable data sources that can be quantified and used for the computation of pertinent safety metrics.

safety↗
NASA NTRS2018

Identification of Safety Metrics for Airport Surface Operations

A large fraction of safety incidents occurs on the ground during airport surface operations. Although these incidents are mostly non-fatal with a few exceptions, they are high profile incidents that remain a source of concern for the National Transportation Safety Board (NTSB), the Federal Aviation Administration (FAA), major airlines, and other stakeholders of the National Airspace System (NAS). These incidents have historically been mitigated by implementing changes to regulations, policies, and procedures over time. This approach has minimized but not eliminated the risk of occurrences. It is thus important to develop integrated techniques to assess, model, and prevent these incidents by analyzing the risk and likelihood of occurrence and communicating results of the analysis to decision-making personnel who can mitigate and prevent incidents in real time. The research presented in this report builds on prior work of researchers at the NASA Ames Research Center who developed an automated framework, Real-Time Safety Monitoring (RTSM), to enable monitoring and prediction of the safety of the NAS. In the RTSM framework, hazards to flight are translated to safety metrics such as wake vortex encounters or loss of separation, that can be modeled and analyzed offline and also predicted and monitored in real time (online). The intent of this report is to integrate predictable incidents that occur during surface and ground operations into the safety portfolio of the RTSM project by (i) identifying suitable information sources from which ground incidents can be studied, (ii) developing safety metrics correlated with surface operations, and (iii) recommending suitable data sources that can be quantified and used for the computation of pertinent safety metrics.

ground operations↗
NASA NTRS2008

Numerical Determination of Critical Conditions for Thermal Ignition

The determination of ignition or thermal explosion in an oxidizing porous body of material, as described by a dimensionless reaction-diffusion equation of the form .tu = .2u + .e-1/u over the bounded region O, is critically reexamined from a modern perspective using numerical methodologies. First, the classic stationary model is revisited to establish the proper reference frame for the steady-state solution space, and it is demonstrated how the resulting nonlinear two-point boundary value problem can be reexpressed as an initial value problem for a system of first-order differential equations, which may be readily solved using standard algorithms. Then, the numerical procedure is implemented and thoroughly validated against previous computational results based on sophisticated path-following techniques. Next, the transient nonstationary model is attacked, and the full nonlinear form of the reaction-diffusion equation, including a generalized convective boundary condition, is discretized and expressed as a system of linear algebraic equations. The numerical methodology is implemented as a computer algorithm, and validation computations are carried out as a prelude to a broad-ranging evaluation of the assembly problem and identification of the watershed critical initial temperature conditions for thermal ignition. This numerical methodology is then used as the basis for studying the relationship between the shape of the critical initial temperature distribution and the corresponding spatial moments of its energy content integral and an attempt to forge a fundamental conjecture governing this relation. Finally, the effects of dynamic boundary conditions on the classic storage problem are investigated and the groundwork is laid for the development of an approximate solution methodology based on adaptation of the standard stationary model.

Luo, W.↗
NASA NTRS1998

Modeling Macro- and Micro-Scale Turbulent Mixing and Chemistry in Engine Exhaust Plumes

Simulation of turbulent mixing and chemical processes in the near-field plume and plume-vortex regimes has been successfully carried out recently using a reduced gas phase kinetics mechanism which substantially decreased the computational cost. A detailed mechanism including gas phase HOx, NOx, and SOx chemistry between the aircraft exhaust and the ambient air in near-field aircraft plumes is compiled. A reduced mechanism capturing the major chemical pathways is developed. Predictions by the reduced mechanism are found to be in good agreement with those by the detailed mechanism. With the reduced chemistry, the computer CPU time is saved by a factor of more than 3.5 for the near-field plume modeling. Distributions of major chemical species are obtained and analyzed. The computed sensitivities of major species with respect to reaction step are deduced for identification of the dominant gas phase kinetic reaction pathways in the jet plume. Both the near field plume and the plume-vortex regimes were investigated using advanced mixing models. In the near field, a stand-alone mixing model was used to investigate the impact of turbulent mixing on the micro- and macro-scale mixing processes using a reduced reaction kinetics model. The plume-vortex regime was simulated using a large-eddy simulation model. Vortex plume behind Boeing 737 and 747 aircraft was simulated along with relevant kinetics. Many features of the computed flow field show reasonable agreement with data. The entrainment of the engine plumes into the wing tip vortices and also the partial detrainment of the plume were numerically captured. The impact of fluid mechanics on the chemical processes was also studied. Results show that there are significant differences between spatial and temporal simulations especially in the predicted SO3 concentrations. This has important implications for the prediction of sulfuric acid aerosols in the wake and may partly explain the discrepancy between past numerical studies (that employed parabolic or temporal approximations) and the measured data. Finally to address the major uncertainty in the near-field plume modeling related to the plume processing of sulfur compounds and advanced model was developed to evaluate its impact on the chemical processes in the near wake. A comprehensive aerosol model is developed and it is coupled with chemical kinetics and the axisymmetric turbulent jet flow models. The integrated model is used to simulate microphysical processes in the near-field jet plume, including sulfuric acid and water binary homogeneous nucleation, coagulation, non-equilibrium heteromolecular condensation, and sulfur-induced soot activation. The formation and evolution of aerosols are computed and analyzed. The computed results show that a large number of ultra-fine (0.3--0.6 nm in radius) volatile HSO4 - HO embryos are generated in the near-field plume. These embryos further grow in size by self coagulation and condensation. Soot particles can be activated by both heterogeneous nucleation and scavenging of H2SO4-H2O aerosols. These activated soot particles can serve as water condensation nuclei for contrail formation. Conditions under which ice contrails can form behind aircrafts are studied. The sensitivities of the threshold temperature for contrail formation with respect to aircraft propulsion efficiency, relative humidity, and ambient pressure are evaluated. The computed aerosol properties for different extent of fuel sulfur conversion to S(VI) (SO3 and H2SO4) in engine are examined and the results are found to be sensitive to this conversion fraction.

Menon, Suresh↗
NASA NTRS1998

Automated Fluid Feature Extraction from Transient Simulations

In the past, feature extraction and identification were interesting concepts, but not required to understand the underlying physics of a steady flow field. This is because the results of the more traditional tools like iso-surfaces, cuts and streamlines were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of much interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one 'snap-shot' of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments like pV3). And methods must be developed to abstract the feature and display it in a manner that physically makes sense. The following is a list of the important physical phenomena found in transient (and steady-state) fluid flow: Shocks; Vortex ores; Regions of Recirculation; Boundary Layers; Wakes.

Haimes, Robert↗
NASA NTRS1999

Automated Fluid Feature Extraction from Transient Simulations

In the past, feature extraction and identification were interesting concepts, but not required to understand the underlying physics of a steady flow field. This is because the results of the more traditional tools like iso-surfaces, cuts and streamlines were more interactive and easily abstracted so they could be represented to the investigator. These tools worked and properly conveyed the collected information at the expense of much interaction. For unsteady flow-fields, the investigator does not have the luxury of spending time scanning only one "snap-shot" of the simulation. Automated assistance is required in pointing out areas of potential interest contained within the flow. This must not require a heavy compute burden (the visualization should not significantly slow down the solution procedure for co-processing environments like pV3). And methods must be developed to abstract the feature and display it in a manner that physically makes sense. The following is a list of the important physical phenomena found in transient (and steady-state) fluid flow: (1) Shocks, (2) Vortex cores, (3) Regions of recirculation, (4) Boundary layers, (5) Wakes. Three papers and an initial specification for the (The Fluid eXtraction tool kit) FX Programmer's guide were included. The papers, submitted to the AIAA Computational Fluid Dynamics Conference, are entitled : (1) Using Residence Time for the Extraction of Recirculation Regions, (2) Shock Detection from Computational Fluid Dynamics results and (3) On the Velocity Gradient Tensor and Fluid Feature Extraction.

Haimes, Robert↗
NASA NTRS2004

Analysis of Surface Charging for a Candidate Solar Sail Mission Using Nascap-2k

The characterization of the electromagnetic interaction for a solar sail in the solar wind environment, and identification of viable charging mitigation strategies, is a critical solar sail mission design task, as spacecraft charging has important implications both for science applications and for sail lifetime. To that end, we have pexformed some preliminary surface charging calculations of a candidate 150 meter class solar sail spacecraft for the 0.5 AU solar polar orbit and a 1.0 AU L1 orbit. We construct a model of the spacecraft with candidate materials having appropriate electrical properties using Object Toolkit and perform the spacecraft charging analysis using Nascap-2k, the NASA/AFRL sponsored spacecraft charging analysis tool. We use mean and extreme solar wind environments appropriate for the 0.5 AU and 1.0 AU missions to establish current collection of solar wind ions and electrons. In addition, we include a geostationary orbit case to demonstrate a bounding example of extreme (negative) charging of a solar sail spacecraft in the geostationary orbit environment. Results from the charging analysis demonstrate that minimal differential potentials (and resulting threat of electrostatic discharge) occur when the spacecraft is constructed entirely of conducting materials, as expected. Examples with dielectric materials exposed to the space environment exhibit differential potentials ranging from a few volts to extreme potentials in the kilovolt range. Recommendations for further analyses include calculations of wake effects, surface current densities, and environments effects on conductivities.

Neergaard, Linda F.↗