Search NASA⌕ Search

SEARCH · Search NASA

Results for “wake recovery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Blade planform design optimization to enhance turbine wake control

Abstract This study considers optimizing the planform of wind turbine blades to ultimately enhance wind plant controls, namely, wake steering strategies. Adjoint‐enabled unsteady actuator line simulations are carried out to obtain gradients for optimization of several different performance objectives with respect to blade chord length at 10 locations along blade span. We demonstrate different blade design optimizations that can maximize time‐averaged lateral wake deflection, entrainment of kinetic energy, or total power of multiple turbines. Our optimized designs can produce a 4+% increase in wake deflection, a 4× increase in vertical kinetic energy entrainment, or a 3.6% increase in power when compared with the baseline case. While lateral wake deflection is only modestly sensitive to chord changes, we find that increasing the outboard chord length can dramatically increase kinetic energy entrainment, resulting in faster wake recovery and gains in net power. While this work develops only a few case studies emphasizing relative performance improvements and general trends, these results show the promise of a framework that combines mid‐fidelity computation with adjoint‐based optimization for control and design problems.

WIND ENERGY↗
DOE OSTI2024

Near wake evolution of a tidal stream turbine due to asymmetric sheared turbulent inflow with different integral length scales

Tidal stream turbines deployed at highly energetic open water sites are subjected to sheared inflow in the rotor plane. The inflow shear is expected to cause asymmetric loading on the rotor blades and affect the downstream wake. In the current study, two different turbulent inflow conditions, static-high shear and dynamic shear, were generated via an active-grid turbulence generator. A 1:20 scaled three-bladed horizontal axis tidal turbine model was tested in those conditions. The results were compared to a quasi-laminar case with no imposed turbulence or shear. The results show that the high shear reduces the average performance, with a drop of up to 16% in the optimal power coefficient. Besides, the shear profiles increase torque fluctuations and induce significant differences in wake hydrodynamics between the high-speed (upper) and low-speed (lower) regions. The large integral length scales further enhance the load fluctuations perceived by the rotor but have a negligible effect on the mean wake field quantities and the wake recovery. The lower half region featured a faster breakdown of tip vortex structure and a rapid drop of swirl number, a phenomenon conjectured to be a consequence of the strong turbulence intensities and Reynolds stresses in the lower half region. Furthermore, the sheared turbulent inflow also results in a very intensive energy redistribution process towards large-scale, low-frequency motions, which is important to the downstream turbines.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Recommendations on setup in simulating atmospheric gravity waves under conventionally neutral boundary layer conditions

Wind farm-induced atmospheric gravity waves have been the subject of recent research as they can impact wind farm performance. Pressure variations associated with gravity waves can contribute to the global blockage effect and wind farm wake recovery. Therefore, accurate numerical simulation of flow fields, where wind-farm-induced gravity waves may be produced, is important. Three main considerations in such simulations are the overall domain size, the use of Rayleigh damping near domain boundaries to dampen gravity waves, and advection damping at the inlet to prevent spurious oscillations. Often these considerations are treated ad hoc rather than systematically. This work aims to test and extend the systematic modelling of internal gravity waves proposed in a preliminary investigation to modelling of both internal and trapped gravity waves. The preliminary study identifies the length scales to set the domain and damping layer sizes and the time scale to configure the Rayleigh damping coefficient but under linearly stratified conditions. Large eddy simulations of flow through a wind farm canopy are performed under conventionally neutral boundary layer (CNBL) conditions to test the validity of proposed setups for CNBL conditions. Background atmospheric parameters, such as Froude number (Fr), inversion height (H i ), and inversion layer Froude number (Fr i ) control most of the atmospheric gravity wave characteristics. We validated for CBNL conditions that the effective wavelengths of the internal gravity waves are the correct length scale to configure the domain size and damping layer thickness. Likewise, the optimum damping coefficient to dampen the internal gravity waves relates to the free atmosphere's buoyancy frequency or buoyant perturbations' time scale. We infer that the damping coefficient in the inversion layer may relate to the inversion buoyancy frequency to effectively dampen the trapped gravity waves. Moreover, the advection damping length is linked to the horizontal wavelength of the trapped gravity waves in the inversion layer to prevent spurious waves at the inlet by retaining wave energy accumulation.

17 WIND ENERGY↗
DOE OSTI2025

Modeling Offshore Wind Farm Performance in Coastal Low-Level Jets Using Coupled Mesoscale-Microscale Large Eddy Simulations

Accurately predicting wind farm reliability under complex offshore atmospheric conditions remains a key challenge, particularly during noncanonical meteorological events such as coastal low-level jets (LLJs). LLJs, characterized by strong nonmonotonic vertical shear and directional veer, depart significantly from the simplified inflow assumptions embedded in conventional design standards, low-fidelity engineering models, and microscale large eddy simulations of the atmospheric boundary layer. In this work, we use the virtual wind farm framework—an exascale, graphics processing unit–accelerated large eddy simulation platform coupled with high-fidelity aeroservoelastic turbine models and advanced mesoscale-microscale coupling via the ExaWind software stack—to investigate turbine responses under realistic LLJ forcing. Simulations are performed over the U.S. North Atlantic offshore domain with the use of meteorological inputs from New York State Energy Research and Development Authority buoy data, focusing on a representative LLJ case impacting the International Energy Agency 15 MW reference turbine. Our results show that LLJs can cause up to 50% power deficits in downstream turbine rows and significantly amplify low-speed shaft and tower loads through nonlinear coupling between complex inflow characteristics and turbine structural dynamics. Two primary mechanisms drive these load amplifications: (1) unique LLJ inflow features—including veer and vertical/lateral shear—and (2) the downstream evolution of the flow under stable thermal stratification, which suppresses turbulence mixing and alters wake recovery. These mechanisms produce streamwise variations in turbine loading not captured by standard hub height–based metrics or existing design load case (DLC) definitions. This study highlights the critical role of rotor-scale flow gradients in driving fatigue and system-level aeroelastic responses, challenging current DLC and control strategies. We advocate the integration of full-flow field, environment-aware wind inputs into load modeling and control algorithms. By leveraging exascale computing to resolve mesoscale-microscale coupling, this work lays the groundwork for next-generation offshore wind turbine design and operation in meteorologically complex marine environments.

17 WIND ENERGY↗
DOE OSTI2024

Enabling "Fuel" Switching through On-Demand Wind Control

This work demonstrates that classical shear-flow stability theory can be successfully applied to modify wind turbine wakes and also explains the success of several emerging, empirically-arrived control methods (i.e., dynamic induction and helix control). Linear stability theory predictions are extended to include the effects of non-axisymmetric inflow profiles, such as wind shear, which is shown to not strongly affect the primary forcing frequency. The predictions, as well as idealized large-eddy simulations using actuator-line representation of the turbine blades, agree that the n = 0 and ±1 modes have faster initial growth rates than higher-order modes, suggesting the lower-order modes are more appropriate for wake control. Exciting the lower-order modes with periodic pitching of the blades produces higher entrainment into the wake and consequently faster wake recovery.

17 WIND ENERGY↗
DOE OSTI2023

ARCUS Vertical-Axis Wind Turbine (Final Scientific/Technical Report)

While land-based wind energy has become economically competitive with traditional energy generation sources in the U.S., offshore wind is not. For floating offshore wind this difference is even more substantial where the levelized cost of energy (LCOE) is projected to be around 3-5 times more expensive than land-based wind. The turbine capital costs represent around 50% of the LCOE for land-based wind sites, but the increased system costs for floating offshore wind reduce this to 20%. The platform and mooring costs are the single largest contributor to the LCOE for floating offshore wind where their mass must counteract the overturning moment caused by the turbine’s thrust force. Despite the high costs of the platform and relatively low cost of the turbine, current offshore wind turbines are designed essentially the same as for land-based sites. Reducing the LCOE is the greatest challenge to realize the benefits of sustained development of floating offshore wind in the U.S. Reducing the complicated system costs of floating offshore wind will enable the industry to continue to grow and outpace current projections if reduced cost curves can be reached. The ideal wind energy system would remove all mass and cost that is not directly capturing energy from the wind. For floating offshore wind energy systems, this objective is even more significant as increased mass above the water level must be supported by larger and more expensive floating platforms. For this reason, vertical-axis wind turbines (VAWTs) are ideal for floating offshore sites and have several advantages over horizontal-axis wind turbines (HAWTs) at this scale. Large VAWTs offer opportunities for improved energy capture over HAWTs as single units and with reduced wind plant aerodynamic losses through enhanced wake recovery. Additionally, the platform-level placement of the VAWT drivetrain greatly reduces the demands placed on the floating platform and its mass and cost. The ARCUS vertical-axis wind turbine concept (U.S. 11,421,650 B2) is an iteration beyond traditional Darrieus-type VAWTs that replaces the rigid tower with blades that are bent into shape and held in place with tensioned center supports, like a bow. The ARCUS design has been shown to further decrease the VAWT rotor mass properties, with a 50% reduction over traditional Darrieus VAWTs quantified in the ATLANTIS program. The ARCUS VAWT’s efficient use of material for the rotor and turbine support structures combined with its lowered center of gravity enables a tension-leg platform (TLP) with simplified installation procedures. TLPs have been an emerging platform architecture in the Oil and Gas industry and demonstrated to have the lowest hull mass requirements while maintaining stability with minimal roll and pitch deflections in operation. A 22 MW ARCUS turbine has been designed with a three-column TLP that enables quayside integration of the turbine while maintaining system stability during tow-out and installation and having optimal mass and cost properties. A comprehensive analysis shows the optimal ARCUS TLP system design minimizes LCOE through efficient material usage and increased energy capture to yield a competitive LCOE estimate of $\$$55/MWh. A comparison with a reference HAWT, having the same swept area, quantifies the advantages that helped to produce this improved LCOE for the ARCUS concept: (1) 30% reduction in total turbine mass, (2) 70% reduction in turbine center of gravity, and (3) 45% increase in energy production over what is optimal for a HAWT. Intellectual property has been generated through the ATLANTIS program providing opportunities to further reduce the LCOE and improve the performance of the ARCUS turbine and TLP system, expanding the list of innovations to support commercial development of the ARCUS concept.

17 WIND ENERGY↗
DOE OSTI2025

Investigating the relationship between simulation parameters and flow variables in simulating atmospheric gravity waves for wind energy applications

Wind farms, particularly offshore clusters, are becoming larger than ever before. Besides influencing the surface wind flow and the inflow for downstream wind farms, large wind farms can trigger atmospheric gravity waves in the inversion layer and the free atmosphere aloft. Wind-farm-induced gravity waves can cause adverse pressure gradients upstream of the wind farm, which contribute to the global blockage effect, and can induce favorable pressure gradients above and downstream of the wind farm that enhance wake recovery. Numerical modeling is a powerful means of studying these wind-farm-induced atmospheric gravity waves, but it comes with the challenge of handling spurious reflections of these waves from domain boundaries. Typically, approaches which employ radiation boundary conditions and forcing zones are used to avoid these reflections. However, the simulation setup of these approaches relies heavily on ad hoc processes. For instance, the widely used Rayleigh damping method requires ad hoc tuning to produce a setup that may only produce satisfactory results for a particular case. To provide more systematic guidance on setting up realistic simulations of atmospheric gravity waves, we conduct a large-eddy simulation (LES) study of flow over a 2D hill and through a wind farm canopy that explores the optimum domain size and damping layer setup depending on the fundamental parameters which determine the flow characteristics. In this work, we only consider linearly stratified conditions (i.e., no inversion layer), thereby focusing on internal gravity waves in the free atmosphere and their reflections from the domain boundaries. This type of flow is governed by a single Froude number, which dictates most of the internal wave properties, such as wavelength, amplitude, and direction. This, in turn, will dictate the optimum domain size and Rayleigh damping layer setup. We find the effective horizontal and vertical wavelengths (the representative wavelengths of the entire wave spectrum) to be the appropriate length scales to size the domain and damping layer thickness, and the optimal Rayleigh damping coefficient scales with the Brunt–Väisälä frequency. Considering Froude numbers seen in wind farm applications, we propose recommendations to limit the reflections to less than 10 % of the total upward-propagating wave energy. Typically, damping is done at the top boundary, but given the non-periodic lateral boundary conditions of practical wind farm simulation domains, we find that damping the inflow–outflow boundaries is of equal importance to damping the top boundary. The Brunt–Väisälä frequency-normalized damping coefficient should be between 1 and 10. The damping layer thickness should be at least one effective vertical wavelength; damping layers exceeding 1.5 times the vertical wavelength are found to be unnecessary. The domain length and height should accommodate at least one effective horizontal and vertical wavelength, respectively. Moreover, Rayleigh damping does not damp the waves completely, and the non-damped energy might accumulate over the simulation time.

17 WIND ENERGY↗
DOE OSTI2025

Comparison of wind farm control strategies under realistic offshore wind conditions: turbine quantities of interest

Abstract. Wind farm flow control is a strategy to increase the efficiency and therefore lower the levelized cost of energy of a wind farm. This is done using turbine settings such as the yaw angle, blade pitch angles, or generator torque to manipulate the flow behind the turbine, affecting downstream turbines in the farm. Two inherently different wind farm flow control methods have been identified in the literature: wake steering and wake mixing. This paper focuses on comparing the turbine quantities of interest between these methods for a simple two-turbine wind farm setup, while a companion article (Brown et al., 2025) focuses on the wake quantities of interest for a single wind turbine setup. Both papers use the same set of wind farm simulations based on high-fidelity large-eddy simulations (LESs) coupled with OpenFAST turbine models. First, precursor simulations are executed in order to match wind conditions measured with lidars in an offshore wind farm off the east coast of the USA. These measurements show general wind conditions that exhibit substantially higher vertical wind shear and veer than any of the LES studies performed with wind farm flow control strategies currently available in the literature. The precursors are used to evaluate the effectiveness of the control methods. In the LES, the wind veer leads to highly skewed wakes, which have considerable influence on the power uplift of wind farm flow control strategies. In addition to a baseline controller, four different control strategies, each of which uses either pitch or yaw control, are performed on the upstream turbine of a simple two-turbine wind farm. Assuming that the wind direction is known and constant over time, the simulations show that wake steering is generally the superior wind farm flow control strategy, considering both wind farm power production and turbine damage equivalent loads when substantial wind veer is present. This result is consistent over different wind speeds and wind directions. On the other hand, for similar wind conditions with lower veer, wake mixing was found to yield the highest power production, although at the expense of generally higher loads. This leads us to conclude that the effect of wind veer, which has so far not usually been considered, can not be neglected when determining the optimal wind farm flow control strategy.

17 WIND ENERGY↗
DOE OSTI2026

Dependence of wind-farm-induced gravity waves and wind farm performance on non-dimensional atmospheric parameters and simulation configuration

This large-eddy simulation (LES) study examines how wind-farm-induced atmospheric gravity waves (AGWs) and wind farm performance depend on non-dimensional atmospheric parameters and simulation configuration. A hypothetical aligned wind farm of actuator disks is simulated under neutral surface conditions, with a stable capping inversion and a mildly stable free atmosphere, to assess the effects of stratification beyond the atmospheric boundary layer (ABL) on ABL flow. Simulation set-ups fully resolving AGWs are validated to minimize spurious wave generation and reflection from the domain boundaries. The validated set-up is then used to analyze AGW types and characteristics, as well as stratification impacts under conventionally neutral boundary layer (CNBL) conditions. These conditions are governed by four non-dimensional parameters: the Froude numbers of the free atmosphere and capping inversion (Fr, Fr i ), and the aspect ratios of the ABL and wind farm (H̃ i , S h ). Simulation configurations that fully resolve AGWs – capturing at least one wavelength both horizontally and vertically – yield the most realistic stratification effects on ABL flow, whereas partial or unresolved configurations produce non-physical, channel-like behavior. A coherent description of the AGW phenomena is provided, highlighting the central role of capping inversion displacement in linking ABL fluctuations with AGWs. Trapped waves are confined within the capping inversion, while interfacial and internal waves aloft are identified as the AGW types most relevant to wind farm performance. The wavy inversion, analogous to an interfacial wave, forms converging and diverging zones that drive power fluctuations across the farm. The interfacial wavelength, measured over the wind farm, corresponds to one diverging, one converging, and one mildly diverging zone. As the interfacial wavelength decreases with Fr i , multiple convergence–divergence zones develop under sub-critical conditions (Fr i <1.0), while for super-critical conditions (Fr i > 1.0), the wavelength approaches the farm length. Wave amplitude increases with decreasing H̃ i (i.e., shallower capping inversions). Wind farm performance is most sensitive to H̃ i : shallow boundary layers increase blockage and reduce efficiency, while deeper layers enhance efficiency. Increasing Fr and Fr i mitigates blockage, and increasing S h mainly improves wake recovery. Although local power fluctuations arise from AGWs, overall wind farm efficiency remains nearly constant with Fr and Fr i , improving primarily with larger H̃ i and S h .

17 WIND ENERGY↗
DOE OSTI2022

Understanding Low Level Jets in the US Atlantic Offshore

Low level jets (LLJs) in the atmosphere exhibit a local windspeed maximum in the boundary layer, with positive shear beneath the jet and negative shear above the jet. Wind turbines tend to experience increased loads with varying wake recovery characteristics in the presence of an LLJ, therefore understanding the mechanism and impact of LLJs is crucial to wind energy development. The US Mid-Atlantic offshore region is a huge potential wind energy resource, yet LLJs in this area are poorly understood. In particular, the coastal offshore environment does not exhibit the same diurnal cycle that leads to strong LLJs in the well-characterized Great Plains region. In this study, we use the Weather Research and Forecasting model (WRF) plus lidar buoy data to identify case studies for LLJ events in 2020 in the New York Bight. A reduced order model is presented to explain the onset of these events based on the competing effects of baroclinicity and eddy diffusivity. Finally, using the macro-scale WRF, we drive a micro-scale large eddy simulation (LES) to generate a more detailed characterization of the Marine Boundary Layer during an LLJ. Gaining a better understanding of LLJs and their impacts on offshore wind in the mid-Atlantic is crucial for a transition toward renewable energy.

atmospheric boundary layer↗
DOE OSTI2023

21-Year Modeled Spatiotemporal Low-Level Jet Climatology Along the U.S. Mid-Atlantic Coast

Offshore wind farms are influenced by a variety of meteorological phenomena, ranging in spatial and temporal extent. One of these phenomena, the low-level jet (LLJ), is defined as a local maximum in wind speed with height in the planetary boundary layer, exhibiting a "nose-like" structure usually in the lowest few hundred meters above the surface. This vertical extent of LLJs may coincide with the rotor-swept area of a wind turbine, thus having implications for potential power production and mechanical loading. Previous studies in this area based on observations have confirmed the prevalence of LLJs here, with implications on power generation, wind turbine loads, and wake recovery depending on the LLJ characteristics, such as nose height and what part of the wind turbine power curve is being impacted.

LLJ↗
DOE OSTI2020

The effect of dynamic near-wake modulation on utility-scale wind turbine wake development

High-resolution field-scale experiments using flow visualization with natural snowfall and high-fidelity large eddy simulations are combined to investigate the effect of dynamic turbine operation and atmospheric conditions on wind turbine wake mixing and recovery in the wake of a 2.5 MW wind turbine. Instantaneous near-wake expansion and deflection in response to changes in blade pitch and wind direction, termed dynamic wake modulation, is quantified using both techniques, demonstrating excellent agreement. The simulations are used to extend these results by calculating the energy flux into the wake 7 rotor diameters downstream, showing that dynamic turbine-atmospheric interactions enhance mixing in the far-wake. This finding is exhibited under both uniform and turbulent inflow conditions. Under turbulent flow, a synergistic relationship is also observed between dynamic wake modulation and wake meandering, as wake recovery can be further accelerated when the two phenomena occur together. The results of this study have implications for the development of more realistic far-wake models that include the significant impact of dynamic wake modulation on wake mixing and development. Additionally, the findings from the current study can be used to develop advanced control algorithms to speed up wake breakdown and recovery, further improving wind farm efficiency.

17 WIND ENERGY↗
DOE OSTI2021

Wake Steering Wind Farm Control With Preview Wind Direction Information: Preprint

Wake steering is a wind farm control strategy in which upstream turbines operate with a yaw misalignment to deflect their wakes away from downstream turbines, yielding a net power gain for the wind plant. But the inability of wake steering controllers to perfectly track the wind direction leads to suboptimal performance. In this paper, we propose the use of preview wind direction measurements upstream of the turbine to improve controller performance by anticipating wind direction changes. Further, data from an operational wind plant are used to determine realistic preview measurement accuracy. Using the FLORIS engineering wind farm control tool, we compare the performance of standard and preview-enabled baseline and wake steering control for a two-turbine array during below-rated operation. Assuming perfect preview information, preview-based wake steering increases energy production by the equivalent of 9.5% of the baseline wake losses, compared to a wake loss recovery of 5.6% with standard wake steering. However, when realistic measurement accuracy is included, the preview-based controller provides no advantage over standard control, motivating the need for more sophisticated control and wind direction forecasting strategies.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2020

Performance and Wake Characterization of a Model Hydrokinetic Turbine: The Reference Model 1 (RM1) Dual Rotor Tidal Energy Converter

The mechanical power and wake flow field of a 1:40 scale model of the US Department of Energy’s Reference Model 1 (RM1) dual rotor tidal energy converter are characterized in an open-channel flume to evaluate power performance and wake flow recovery. The NACA-63(4)-24 hydrofoil profile in the original RM1 design is replaced with a NACA-4415 profile to minimize the Reynolds dependency of lift and drag characteristics at the test chord Reynolds number. Precise blade angular position and torque measurements were synchronized with three acoustic Doppler velocimeters (ADV) aligned with each rotor centerline and the midpoint between the rotor axes. Flow conditions for each case were controlled to maintain a hub height velocity, uhub= 1.04 ms−1, a flow Reynolds number, ReD= 4.4 × 105, and a blade chord length Reynolds number, Rec= 3.1 × 105. Performance was measured for a range of tip-speed ratios by varying rotor angular velocity. Peak power coefficients, CP= 0.48 (right rotor) and CP= 0.43 (left rotor), were observed at a tip speed ratio, λ= 5.1. Vertical velocity profiles collected in the wake of each rotor between 1 and 10 rotor diameters are used to estimate the turbulent flow recovery in the wake, as well as the interaction of the counter-rotating rotor wakes. The observed performance characteristics of the dual rotor configuration in the present study are found to be similar to those for single rotor investigations in other studies. Similarities between dual and single rotor far-wake characteristics are also observed.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Comparison of Rotor Wake Identification and Characterization Methods for the Analysis of Wake Dynamics and Evolution

Optimal wind power plant design requires understanding of wind turbine wake physics and validation of engineering wake models under wake-controlled operating conditions. In this work, we have developed and investigated several different wake identification and characterization methods for analyzing wake evolution and dynamics. The accuracy and robustness of these methods, based on Gaussian function fitting and adaptive contour identification, have been assessed by application to a large-eddy simulation data set. A new contour-based method based on downstream momentum deficit has been considered. Uncertainties arising from wake-identification errors result in characterizations of the wake expansion, recovery, and meandering motion that differ by 19% of the rotor area, 4% of the freestream, and 15% rotor diameter, respectively.

17 WIND ENERGY↗
DOE OSTI2024

Land-based wind plant wake characterization using dual-Doppler radar measurements at AWAKEN

Wind plant wakes have been shown to persist for tens of kilometers downstream in offshore environments, reducing the power output of neighboring plants, but their behavior on land remains relatively unexplored through observation. This study capitalizes on the unique and extensive field data collected for the American WAKE ExperimeNt (AWAKEN) project underway in northern Oklahoma. X-band dual-Doppler radars deployed at this site measure wind speed and direction at 25-m and 2-min resolution within a 30-km range, capturing the interactions between three neighboring wind plants. These measurements show that the wake of one wind plant extends at least 15 km downstream under easterly wind and stable atmospheric conditions. Though the wake wind speed increases within the first 10 km, it plateaus at 90% of the freestream wind speed. The spanwise velocity distribution within the wake initially shows the clear signature of the wind plant layout, which is smoothed as it propagates downstream, indicating spanwise momentum transfer is a key mechanism in wind plant wake development and recovery. These findings have important implications for wind plant siting decisions and resource assessments, and provide insights into atmospheric interactions at the wind plant scale.

17 WIND ENERGY↗
DOE OSTI2022

Toward control co-design of utility-scale wind turbines: Collective vs. individual blade pitch control

A large-eddy simulation framework has been coupled with controller modules to systematically investigate the impacts of collective (CPC) and individual (IPC) pitch control strategies on utility-scale wind turbine energy production and fatigue loads. Wind turbine components were parameterized using an actuator surface model to simulate the rotor blades and the turbine nacelle. The baseline CPC and IPC algorithms, consisting of single-input single-output proportional–integral controllers and two integral controllers, respectively, were incorporated into the numerical framework. A series of simulations were carried out to investigate the relative performance of the two controllers under various turbulent inflow conditions, spanning hub-height velocities of 7 to 14 m/s. The numerical simulation results of this study showed that, in comparison to the CPC, the IPC controller could successfully reduce the damage equivalent loads of utility-scale turbines at regions 2 and 3 of turbine operation by about 3% and 40%, respectively, without any penalty on the power production of the turbine. It was also shown that, despite its minor impact on the turbulence kinetic energy of the wake, the IPC controller did not influence the recovery of the turbine wake.

17 WIND ENERGY↗
DOE OSTI2021

Numerical investigation of wind turbine wakes under high thrust coefficient

Abstract We study wind turbine wakes of rotors operating at high thrust coefficients ( C T > 24/25) using large‐eddy simulations with a rotating actuator disk model. Wind turbine wakes at high thrust coefficients are different from wakes at low thrust coefficients. Wakes behave differently at high thrust, with increased turbulence and faster recovery. Lower induction in the wake is achieved because wakes in high‐thrust conditions recover much faster than in normal operating conditions. This enhanced recovery is possible thanks to the turbulence generated in the near wake. We explore the mechanism behind this behavior and propose a simple model to reproduce it. We also propose a Gaussian fit for the wakes under high‐thrust conditions and use it use it to initialize an Ainslie type model within the FAST.Farm framework.

FAST.Farm↗